Craftsman 32010871 Owner’s Manual

13 Amp

7 14°in°Circular

with Laser TracT_'_

Model No.

320.10871

DOUBLE INSULATED

oWARRANTY

Z_ CAUTION Read, understand and follow

all Safety Rules and Operating Instructions in this Manual before using this product.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www.craftsman.com

I I

• SAFETY o UNPACKING

o ASSEMBLY ° DESCRIPTION ,' OPERATION ,' ADJUSTMENTS

• MAINTENANCE

Warranty .............................................................................. Page 2

Safety Symbols ....................................................................... Page 3

Safety Instructions .................................................................... Pages 4 - 11

Glossary of Terms ......................................................................... Pages 11 - 12

Unpacking ............................................................................ Pages 12 - 13

Assembly ......................................................................................... Pages 13- 14

Description ......................................................................... Pages 15 - 17

Operation ............................................................................ Pages 17 - 27

Adjustments ......................................................................... Page 28- 29

Maintenance ........................................................................... Pages 29 - 30

Troubleshooting ......................................................................... Page 30

Accessories ................................................................................. Page 30

Repair Parts ............................................................................ Pages 31 - 34

Sears Repair Parts Phone Numbers ............................................. Back Cover

ONE YEAR FULL WARRANTY ON CRAFTSMAN _ PRODUCT

If this Craftsman product fails due to a defect in material or workmanship

within one year from the date of purchase, RETURN ITTOTHE NEAREST SEARS STORE OR PARTS AND REPAIR CENTER OR

OTHER CRAFTSMAN OUTLET IN THE UNITED STATES FOR FREE

REPAIR (OR REPLACEMENT IF REPAIR PROVES IMPOSSIBLE).

This warranty does not include expendable parts such as lamps, batteries, bits or blades.

If this Craftsman product is used for commercial or rental purposes,

this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also

have other rights, which vary from state to state. Sears, Roebuck and Co., Hoffman Estates, IL 60179

SAVE THESE INSTRUCTIONS!

READ ALL INSTRUCTIONS!

Thepurposeofsafetysymbolsistoattractyourattentionto possibledangers. Thesafetysymbols,andtheexplanationswiththem,deserveyourcareful

attentionandunderstanding.ThesymbolwarningsDONOTbythemselves eliminateanydangerTheinstructionsandwarningstheygivearenosubstitutes

forproperaccidentpreventionmeasures

z_ WARNING: BE SURE to read and understand all safety instructions in ,,

this ,manual, including all safety alert symbols such as "DANGER", "WARNING

I and CAUTION , BEFORE using this saw. Failure to follow all instructions _ below may result in electric shock fire and/or serious personal injury, .

SYMBOL MEANING

Z_ SAFETY ALERT SYMBOL: Indicates DANGER,WARNING,OR

[ Z_WARNING ]

I _ CAUT_ON ] Failure to obey this safety warning MAY result in personal

DAMAGE PREVENTION AND INFORMATION MESSAGES

These informuser of important information and/or instructions that could lead to

equipment or other property damage if not followed. Each message is preceded by the word "NOTE:" as in the example below:

NOTE: Equipment and/or property damage may result if these instructions are not followed.

CAUTION, May be used in conjunction with other symbols or pictographs,

DANGER: Failure to obey this safety warning WILL result in death or serious injury to yourself or to ethers. Always

follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

Failure to obey this safety warning CAN result in death or serious injury to yourself or to others. Always follow the

safety precautions to reduce the risk of fire, electric shock and personal injury.

injury to yourself or others or property damage, Always

follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

]

WEAR YOUR

z_WARNING: The operation of any tool with a cimular

blade can result in foreign objects being thrown into

your eyes, which can result in severe eye damage.

Before beginning power tool operation, ALWAYS wear safety goggles or safety glasses with side shield and

a full-face shield when needed. We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shield, available at Sears Stores

or other Craftsman Outlets.

z_WARNING: BE SURE to read and understand all instructions in this

manual before using this circular saw. Failure to follow all instructions may result in hazardous radiation exposure, electric shock, fire and/or serious

personal injury.

SAFETY PRECAUTIONS FOR LASERS This circular saw has a built-in laser light The laser is a Class Ilia and emits output power

of a maximum 1mW and 635-665nm wavelengths These lasers do not normally present an optical hazard However, DO NOT stare at the beam as this can cause flash blindness

The following label is on your tool.

It indicates where the saw emits the

laser light. BE AWARE of the laser light

location when using, ALWAYS MAKE

SURE that any bystanders in the vicinity

of use are made aware of the dangers

of looking directly into the laser.

Exposure. DO NOT stare into beam. Only turn laser beam on when the saw

[ /_,WARNING: LASER LIGHT. LASER RADIATION. Avoid Direct Eye

is on the workpiece. Class Ilia laser,

other than those specified in this manual may result in hazardous radiation

[ _WARNING: Use of controls, adjustments or performance of procedures

exposure.

telescopes or transits to view the laser beam will increase eye hazard.

[ Z_WARNBNG: The use of optical instruments such as, but not limited to,

1 DO NOT remove or deface any product labels. Removing product labels

increases the risk of exposure to laser radiation.

2, The laser beam can be harmful to the eyes. ALWAYS avoid direct eye exposure.

DO NOT look directly into the laser beam output aperture during operation DO NOT project the laser beam directly into the eyes of others. Turn laser on ONLY when making cuts.

3 Laser enhancing safety glasses are included to enhance the laser beam in bright light

conditions DO NOT wear these glasses if they interfere with the safe operation of this saw.

4, The laser on the circular saw is not a toy. ALWAYS keep out of the reach of

children, The laser light emitted from this device SHOULD NEVER be directed

towards any person for any reason,

5. BE SURE the laser beam is aimed at a workpiece (such as wood or rough coated surfaces) that does not have a reflective surface

6. DO NOT use on surfaces such as sheet steel that have a shiny, reflective surface. The shiny surface could reflect the beam back at the operator, Be aware that laser

light reflected off of a mirror or any other reflective surfaces can also be dangerous

7oALWAYS turn the laser beam off when not in use. Leaving the tool on increases

the risk of someone inadvertently staring into the laser's beam.

when using this laser. Use of this feature in any manner other than what appears

/_ CAUTION: ALWAYS follow only the instructions contained in this manual /

in this manual may result in a hazardous radiation exposure,

8. DO NOT attempt to modify the performance of this laser device in any way, This may result in a dangerous exposure to laser radiation.

9. ALWAYS use only the accessories that are recommended by Sears for use

with this producL Use of accessories that have been designed for use with other laser tools could result in serious injury.

10.

For further information regarding lasers, refer to ANSI-Z136.1 The STANDARD FOR THE SAFE USE OF LASERS, available

from the Laser Institute of America (407) 380-1553.

WORK AREA SAFETY

1_Keep your work area clean and well lit. Cluttered workbenches and dark areas

invite accidents°

2. DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes,

3. Keep bystanders, children and visitors away while operating a power tool. Distractions can cause you to lose control

4. Make your workshop childproof with padlocks and master switches_ Lock tools away when not in use.

5. MAKE SURE the work area has ample lighting so you can see the work and that

there are no obstructions that will interfere with safe operation BEFORE using your saw

PERSONAL SAFETY

1. KNOW your power tool. Read the operator's manual carefully. Learn the saw's

applications and limitations, as well as the specific potential hazards related to this tool.

2. STAY ALERT, watch what you are doing and use common sense when operating a power tool.

3. DO NOT use tool while tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

4. DRESS properly. DO NOT wear loose clothing or jewelry. Pull back long hair, Keep your hair, clothing, and gloves away from moving parts° Air vents often cover moving parts and should also be avoided. Loose clothing, jewelry or long hair can be caught in moving pads°

PERSONAL SAFETY cont.

5. AVOID accidental starting. Re sure switch is in "OFF" position before plugging in DO NOT carry tools with your finger on the switch. Carrying tools

with your finger on the switch or plugging in tools that have the switch in the

"ON" position invites accidents

6. REMOVE adjusting keys or wrenches before turning the tool "ON". Awrench

that is left attached to a rotating part of the tool may result in personal injury,

7 Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the toot in unexpected situations.

8. ALWAYS SECURE YOUR WORK. Use clamps or a vise to hold work when practical It is safer than using your hand and frees both hands to operate tool.

9 USE SAFETY EQUIPMENT, Always wear eye protection Dust mask, non-skid

safety shoes, hard hat, or hearing protection must be used for appropriate condilions.

10o DO NOT USE ON A LADDER or unstable support. Stable footing on a solid

surface enables better control of the tool in unexpected situations,

TOOL USE AND CARE SAFETY

_, WARNING : BE SURE to read and understand all instructions before

operating this saw. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

1, ALWAYS use clamps or other practical ways to secure and support the

workpiece to a stable platform. Holding the work by hand or against your body

is unstable and may lead to loss of control

2. DO NOT force the tool. Use the correct tool and blade for your application, The correct tool and blade will do the job better and safer at the rate for which it is

designed,

3 DO NOT use the tool if switch does not turn it "On" or "Off", Any tool that

cannot be controlled with the switch is dangerous and must be repaired.

4 DISCONNECT the plug from the power source before making any adjustments,

changing accessories or storing the tool, Such preventive safety measures reduce the risk of starting the tool accidentally.

5. NEVER leave the tool running. ALWAYS turn it off. DO NOT leave the tool until

it comes to a complete stop.

6. STORE idle tools out of the reach of children and other untrained persons, Tools are dangerous in the hands of untrained users.

7o MAINTAIN tools with care. Keep cutting tools sharp and clean. Properly

maintained tools with sharp cutting edges are less likely to bind and are easier to control.

8 CHECK for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tool's operation If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools,

9. USE ONLY accessories that are recommended for this tool, Accessories that may be suitable for one tool may become hazardous when used on another tool.

ELECTRICAL SAFETY

Z_WARNING: Do not permit fingers to touch the terminals of plug when

installing or removing the plug from the outlet.

1. Double insulated tools are equipped with a polarized plug (one blade is wider than the other).Thls plug will fit in a polarized outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.

2. Double insulation[] eliminates the need for the three-wire grounded power cord and grounded

power supply system. Applicable only to Class II (double-insulated) tools. This circular saw is

a double insulated tool.

Coveror ®

Outlet Box

Grounded _

I-_WARNING: Double insulation DOES NOT take the place of normal safety

precautions when operating this tool.

3, BEFORE plugging in the tool. BE SURE that the outlet voltage supplied is within

the voltage marked on the tool'sdata plate. DO NOT use "AC only" rated tools with a DC power supply

4, AVOID body contact with grounded surfaces, such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is grounded.

5 DO NOT expose power tools to rain or wet conditions or use power tools in

wet or damp locations. Water entering a power tool will increase the risk of electric shock.

6, INSPECT tool cords for damager Have damaged tool cords repaired at a Sears

Service Centsr, BE SURE to stay constantly aware of the cord location and keep it well away from the moving blade

7, DO NOT abuse the cord, NEVER use the cord to carry the toot by or pull the

plug from the outlet. Keep cord away from heat, oil, sharp edges or moving parts Replace damaged cords immediately Damaged cords increase the risk of electric shock

EXTENSION CORDS Use a proper extension cord, ONLY use cords listed by Underwriters Laboratories

(UL). Other extension cords can cause a drop in fine voltage, resulting in a loss of

power and overheating of tool For this tool an AWG (American Wire Gauge) size of at least 14-gauge is recommended for an extension cord of 25-ft or less in length

Use 12-gauge for an extension cord of 50-ft Extension cords 100-ft. or longer are not

recommended. Remember, a smaller wire gauge size has greater capacity than a larger number (14-gauge wire has more capacity than 16-gauge wire; 12-gauge wire has more capacity than 14-gauge) When in doubt use the smaller number

When operating a power tool outdoors, use an outdoor extension cord marked "W-A" or "W" These cords are rated for outdoor use and reduce the risk of electric

shock.

Z_ CAUTION: Keep the extension cord clear of the working area. Position

the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool,

Z_WARNING: Check extension cords before each use. If damaged

replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock, resulting in serious injury.

SAFETY SYMBOLS FOR YOUR TOOL

The label on your tool may include the following symbols.

V ....................................................... Volts

A ................................. Amps

Hz......................................... Hertz

W............................................................. Watts

min ...................................... Minutes

_. ............................... Alternating current

.............................. Direct current

no ....................................................... No-load speed

[] ............................................................ Class II construction, Double insulated

/min .................................... Revolutions or Strokes per minute

z_, ............................. Indicates danger, warning or caution

It means attention! Your safety is involved

SERVICE SAFETY

I If any part of this saw is missing or should break, bend, or fail in any way;

or should any electrical component fail to perform properly: SHUT OFF the power switch and lemove the saw plug from the power source and have

the missing, damaged or failed parts replaced BEFORE resuming operation

2, Tool service must be performed only at a Sears Parts and Repair Center,

Service or maintenance performed by unqualified personnel could result in a risk of injury

3 When servicing a tool, use only identical replacement parts, Follow

instructions in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric

shock or injury

SAFETY RULES FOR CIRCULAR SAWS

Keep hands away from cutting area and blade. Keep your

second hand on the auxiliary handle or motor housing. If both hands are holding the saw, the blade cannot cut them.

Z_ CAUTION: Blades coast after saw is switched off.

t KEEP your body positioned to eithei side of the saw blade and not in direct

line with the saw blade. Kickback could cause the saw to jump backwards (See "Kickback What Causes It and Ways to Prevent It" on pages 18 and I9)

2. DO NOT reach underneath the work. The guard cannot protect you from the blade beneath the workpiece.

DOES NOT cover the blade on the underside of the workpiece (Pgo 17 Fig. 4).

_ When sawing through a workpiece, the lower blade guard

ALWAYS keep your hands and fingers away from the cutting area.

3. CHECK lower guard for proper closing BEFORE each use. DO NOT operate the saw if the lower guard does not move freely and close instantly. Never clamp or tie the

lower guard in the open position. If the saw is accidentally dropped, timelower guard may be bent. Raise the lower guard with the retracting lever The guard is operating properly when it moves freely, does not touch the blade or any other part in all angles and depths of cut, and readily returns to the closed position

4 CHECK the operation and condition of the lower guard spring, If the guard and the

spring are not operating properly, they MUST BE serviced before use. The lower guard may operate sluggishly, due to damaged pads, gummy deposits, or a buildup of debris DO NOT operate your saw until the damage has been repaired or replaced.

5 The lower guard should be retracted manually ONLY for making special cuts, such

as pocket or compound cuts. ALWAYS raise the lower guard by retracting its lever. As soon as the blade enters the material, the lower guard MUST be released. For al!

other sawing, the lower guard should operate automatically

6 ALWAYS make sure that the lower guard is covering the blade BEFORE placing the

saw down on a work bench or floor. An unprotected moving blade wil! cause the saw to walk backwards, cutting whatever is in its palh Make note of the time it takes for the blade

[o stop spinning alter the switch is released.

7 NEVER hold the piece being cut in your hands or across your legs. tt is important to

support the workpiece properly in order to minimize body exposure, blade binding, or toss of control.

8 HOLD TOOL by insulated gripping surfaces (handles) when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make the exposed metal parts of the tool "live" and shock the operator

9 ALWAYS clamp the workpiece securely so it will not move when making the cut

10 When ripping, ALWAYS USE a rip fence or straight edge guide. This improves the

accuracy of the cut and reduces the chance of the blade binding.

11. ALWAYS USE blades that have the correct size and shape (diamond vso round) arbor holes. Blades that do not match the mounting hardware of the saw will run erratically and

cause loss of control

I I

SAFETY RULES FOR CIRCULAR SAWS cont,

!2 NEVER use damaged or incorrect blade washers or bolts. The blade washers

and bolts were specially designed for your saw, for optimum performance and safety of operation

13 NEVER cut more than one piece at a time. DO NOT STACK more than one

workpiece on the worktable at a time.

!4. AVOID awkward operations and hand positions where a sudden slip could

cause your hand to move into the blade.

15 NEVER reach into the cutting path of the blade.

/fX WARNING: Use of this product can generate dust containing chemicals

known to cause cancer, birth defects or other reproductive harm. Some examples of

these chemicals are:

oLead from lead-baaed paints.

• Crystalline silica from bricks and cement and other masonry products_ . Arsenic and chromium, from chemically treated lumber.

Your risk from these exposures varies, depending upon how often you do this type of work.To reduce your exposure to these chemicals:

• Work in a well-ventilated area. ° Work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling and other construction activities. Wear protective clothing and wash exposed

areas with soap and water.

Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption

of harmful chemicals

WARNING: Use of this tool can generate and/or disburse dust, which may

cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles

away from face and body.

ADDITIONAL RULES FOR SAFE OPERATION

WARNING: BE SURE to read and understand all instructions, Failure

to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

1 Know your power tool. Read operator's manual carefully. Learn the applications

and limitations, as well as the specific potential hazards related to this tool Following this rule will reduce timerisk of electric shock, fire or serious injury

2 ALWAYS wear safety glasses or eye shields when using this saw, Everyday

eyeglasses have only impact-resistant lenses; they are NOT safety glasses

3 PROTECT your lungs. Wear a face mask or dust mask if the operation is dusty

ADDITIONALRULESFORSAFEOPERATIONcont.

4 PROTECT your hearing. Wear appropriate personal hearing protection during use

Under some conditions and duration of use, noise from this product may contribute

to hearing loss

5 ALL VlSTORS AND BYSTANDERS MUST wear the same safety equipment that the

operator of the saw wears,

6 INSPECT the tool cords periodically and if damaged have them repaired at your

nearest Sears Service Center or other Authorized Service Facility. BE AWARE of the cord location,

7, ALWAYS check the tool for damaged parts. Before further use of the tool, a guard or

other part that is damaged should be carefully checked to determine if it will operate properly and perform its intended function Check for misalignment or binding of moving

parts, breakage of parts, and any other condition that may affect the tool's operation

A guard or other part that is damaged should be properly repaired or replaced at a Sears

Service center 8 INSPECT and remove all nails from lumber before sawing, 9, SAVETHESE INSTRUCTIONS, Refer to them frequently and use them to instruct

others who may use this tool, If someone borrows this tool, make sure they have

these instructions also,

Spindle The shaft on which a blade or cutting tool is mounted Also called the Arbor

Revolutions Per Minute (RPM) The number of turns completed by a spinning object in one minute

Saw Blade Path The area over, under, behind or in front of the blade, as it applies to the workpiece. That area which will be or has been cut by the blade,

Set The distance that the saw blade tooth is bent (or set) outward from the face of the blade

Miter Cut

A cutting operation made with the blade at any angle other than 900to the fence

Compound Miter Cut

A compound miter cut is a cut made using a miter angle and a bevel angle at the same time,

Cross cut A cutting or shaping operation made against the grain of the workpiece

Bevel Cut A cutting operation made with the blade at any angle other than 90° to the miter table,

Dado Cut A non-through cut which produces a square-sided notch or trough in the workpiece (requires special blade).

Chamfer Cut A cut removing a wedge from a biock of wood so the end (or part of the end) is angled

at other than 90°

I I

Ripping or Rip Cut

A cutting operation along the length of the workpiece

Freehand Cut Performing a cut without using a fence, miter gauge, fixture, work clamp, or other

proper device to keep the workpiece flora twisting or moving during the cut. Through Sawing

Any cutting operation where the blade extends completely through the thickness of the workpiece

Non-Through Cuts

Any cutting operation where the blade does not extend completely through the thickness of the workpiece, like a dado cut

Leading End

Tile end of the workpiece pushed into toot first

Kerr

The material removed by the blade in a through cut or the slot produced by the blade

in a non-through or partial cut Kickback

A hazard that can occur when tile blade binds or stalls, throwing the workpiece back

toward operator

Werkpiece or Material The item on which the cutting operation is being done The surfaces of a workpiece

are commonly [eferred to as faces, ends and edges Gum

A sticky, sap-based residue from wood products,

Resin

A sticky, sap-based substance that has hardened

when you are assembling parts, making adjustments, installing or removing

blades, cleaning or when it is not in use. Disconnecting the saw will prevent

WARNING: Your saw should NEVER be connected to the power source

accidental starting, which could cause serious personal injury.

1 Included with your circular saw is the cutting blade (unassembled) packed separately

Also a blade wrench stored in the base, for use installing or changing the blade, an

edge guide and a pair of Laser enhancing safety glasses used to enhance the laser beam in bright light conditions

2 Inspect tile saw carefully to make sure that no breakage or damage has occurred during

shipping, If any of the items mentioned are missing (refer to PARTS LIST illustration see Fig1 page 13), return tile saw to your nearest Sears store or Craftsman outlet to have the saw replaced

in the power cord or operate saw until the broken or missing parts are replaced.

WARNING: If any parts are broken or missing, DO NOT attempt to plug ]

Failure to do so could result in possible serious injury.

]

-7

I I

PARTS LIST

(Fig. 1)

4. Blade Wrench I[ !

(forchanging I_J

the blade)

5_Laser Enhancing _/..,F /

Safety Glasses (-/ _11 .(7,U

(forenhancing laser) "_----"

(unassembled, install onto saw)

6. Operator's Manual

INSTALLING THE BLADE (Figs. 2 and 2a) Carefully remove the blade from its packing, inspect it to be sure that it is not cracked

or damage& 1, Saw should not be plugged into power source,

power source BEFORE assembling parts, making adjustments or installing blades.

z_ WARNING: To prevent personal injury, ALWAYS disconnect the plug from

2. Place saw on its side on a flat surface 3 To loosen the depth-of-cut ad ustment lever, raise the saw up all the way and tighten lever

This gives you easier access to blade mounting area (see Fig 2a) 4 Place saw upright, on its base and on a flat surface (see Fig 2a). 5 To loosen the spindle clamping screw "A", depress the spindle lock button (see Fig 2)_

Place the blade wrench on the spindle clamping screw "A", Move the wrench back and

forth until you feel the spindle lock button depress further and it locks the blade in position so the spindle clamping screw can be removed Keeping the spindle lock button

firmly depressed, turn the spindle screw counterclockwise to remove __j__ _ \J

Spindle __

Lock Button

Depth-oI-Cut

Adjustment Lever

Fig. 2a

)uter "D"Washer

Blade Rotation teeth point up at front

=A" Spindle

Clamping Screw

INSTALLING THE BLADE cont. (Figs. 2 and 2a)

L_ WARNING: BE SURE to wear protective work gloves while handling a saw

blade.The blade can injure unprotected hands,,

Z_ WARNING: A 7 1/4-inch blade is the maximum blade capacity of your saw, A

larger than 71/4-inch blade will come in contact with the blade guards. Also, NEVER use a blade that is so thick that it prevents the outer blade washer from engaging

with the flat side of the spindle,, Blades that are too large or too thick can result in

an accident causing serious injury.

6. Completely remove the spindle clamping screw "A" and the outer "D" washer (see Fig, 2a),

7,.The remaining washer is the inner bushing washer that fits around the spindle

shaft and it does not need to be removed,

8,, Put a drop of oil onto the inner bushing washer and outer "D" washer where

they will touch the blade.

9. Raise lower blade guard using the blade guard lever and hold it in the raised position for the next step.

10, Place the saw blade inside the lower blade guard, onto the spindle shaft

and against the inner bushing.

shown in (Fig. 2a),

NOTE: The teeth of the blade should point upward at the front of the saw as /

11,.Replace the "D" washer,

12. Firmly hold down spindle lock button as you replace the spindle screw and hand tighten it in a clockwise direction, Then use blade wrench to tighten the spindle clamping screw thoroughly,

with the flat side of the spindle.

NOTE: NEVER use a blade that is too thick to allow the"D"washer to engage I

REIVIOVING THE BLADE (Figs. 2 and 2a)

1, Unplug the saw,

2, Follow steps 2, through 6, of "INSTALLING THE BLADE" and

remove the blade (see Fig. 2a).

-I

KNOW YOUR CIRCULAR SAW (Fig, 3)

NOTE: Before attempting to use your saw, familiarize yourself with all of the

operating features and safety requirements.

Your circular saw has a precision-built eiectdc motor and it should only be connected to a 120-volt, 60-Hz AC ONLY power supply (normal household current). DO NOT operate on direct current (DC). This large voltage drop will cause a loss of power and the motor will overheat, If the saw does not operate when plugged into correct 120-volt, 60-Hz AC ONLY outlet, check the power supply The saw has an 8-fL, 2-wire power cord

(no adapter needed). This Circular Saw has the following features:

1.13 Amp, 5000 RPM (no-load speed) motor provides the power and torque for fast, sure cuts in wood, plywood, hardboard and wood-base materials.

2. LaserTrac T_The unique, innovative feature for accurate, efficient cutting!

3. LED WORKLIGHT illuminates cutting area for easy visibility.

This light stays "On" when saw is plugged into power source.

]

4. Quick depth-of-cut adjustments with a maximum depth of cut: 2 3le-in. thick at 90; 1 13hs-in. thick at 45°

5. Easy to read bevel cut scale adjusts from 0° to 52° bevel capacity.

6. Die-cast aluminum blade guards for extra strength and durability,

7. Extended length, trigger switch for maximum control and comfort. Squeeze for power "ON", release for power "OFF"°

8. Large stamped Steel Base provides a stable work surface for better saw control.

9. Soft-grip ergonomically designed contoured rear handle and front assist handle for positive gripping, control, balance and comfort.

10. Includes Craftsman ®24 tooth carbide-tipped steel general purpose blade.

11. Top mounted blade spindle lock for easy blade changes.

12. Includes edge guide to help produce accurate cuts. 13_Sawdust ejection chute helps direct dust and chips away from operator.

14_ Permanently lubricated '100% ball bearings for smooth operation and tong life,

15. Durable machined gearing for efficient power transmission.

This Circular Saw has the following features cont.

Fig, 3 TriggerSwitch

Rear Handle

Upper Blade Guard

Lower Blade Guard Lever

Spindle Clamping

Screw

Laser Light Aperture

Mounting Slots for Edge Guide

Front Assist Handle

MotorHousing

I Scale

Bevel Adjustment Locking Lover

Base

_oge Guide Locking/retaining

Screw

Spindlo Lock Button

Motor Housing --

Depth-of-Cut Adjustment Lever

Loosen _

Tighten 4"

Base

Cut Scale

Lower Blade

-Blade Wrench (storesinbase)

Input Rating

No Load Speed

Blade Diameter Cutting Depth at 90° Cutting Depth at 45°

Maximum Bevel Angle

SAW BLADES All saw blades need to be kept clean,

sharp and properly set in order to cut efficiently Using a dull blade places a

heavy load on the saw and increases the danger of kickback Keep extra blades on hand, so sharp blades are always available Gum and wood pitch

hardened on the blade slows the saw down Use gum and pitch remover,

hot water or kerosene to remove them, DO NOT use gasoline

13 Amps 120V, 60HZ AC

5000 RPM

71/,_-in. (184mm)

23/a-in. (60.33mm)

113/1G-in. (46.03mm)

52 °

Fig. 4 r Blade

BLADE GUARD SYSTEM (FiG 4) The lower blade guard, attached to

your circular saw, is there for your protection and safety, It should

NEVER be altered for any reason, If it becomes damaged or begins to return slowly or sluggishly, DO NOT operate your saw until the damage has been repaired or replaced. ALWAYS leave the guard in its correct operating position when using the saw.

CAUTION: NEVER use the saw when the guard is not operating properly. The

guard should be checked for correct operation before each use, If you drop your saw, check the lower blade guard and bumper for damage at all depth settings before using, NOTE: The guard is operating properly when it moves freely and then readily returns to the closed position. If for any reason your lower blade guard and bumper does not close freely, take the saw to your nearest Sears Repair Center for service before using it.

KICKBACK...WHAT CAUSES IT AND WAYS TO HELP PREVENT IT (Fig. 5) The Causes of Kickback

Correct Blade Depth Blade is Set Too

Fig. 5

1 Kickback is a sudden reaction to a pinched,

bound or misaligned saw blade, which causes an uncontrolled saw to lift up and out of the workpiece and toward the operator.

2 When the blade is pinched or bound tightly by the

kerr closing down, the blade stalls and the motor reaction drives the unit rapidly back towards the

operator

3 If the blade becomes twisted or misaligned in the

cut, the teeth at the back edge of the blade can dig into the top surface of the wood This causes the

blade to climb out of the kerr and

jump back towards the operator

4 Sawing into knots or nails in the workpiece

can cause Kickback

5 Sawing into wet or warped lumber can

cause Kickback, (see Fig. 6a)

6 Forcing a cut, or not supporting the workpiece

correctly can cause Kickback (see Fig 6a)

7 Kickback is a result of tool misuse and!or incorrect

operating procedures or conditions

It can be avoided by taldng the proper

precautions, on page 19,

Deep

Fig. 6

Right _

Fig,

--1

Ways to Help Prevent Kickback

or the saw stalls. Kickback could cause you to lose control of the saw_ Loss of control

_ ALWAYS release trigger switch immediately if the blade binds

can lead to serious injury.

ALWAYS maintain a firm grip with both (see Fig 7) hands on the saw and position your body and arms to allow you to resist Kickback forces

Kickback forces can be controlled by the operator, if the proper precautions

are taken

If the blade is binding, or when you are interrupting a cut for any reason, ALWAYS

release the trigger and hold the saw motionless in the material until the blade

comes to a complete stop NEVER attempt to remove the saw from the work or pull the

saw backward while the blade is in motion, or Kickback may occur, CHECK and take

corrective action to eliminate the cause of blade binding 3 Inspect the workpiece for knots or nails before cutting Never saw into a knot or nail 4 DO NOT cut warped or wet lumber (see Fig 6a)

5 ALWAYS support large panels to minimize the risk of blade pinching and Kickback Large

panels tend to sag under their own weight (see Fig 6a) Supports MUST be placed under the panel, one near the line of cut and one near the edge of the panel (see Fig 6)

6 When restarting the saw in the workpiece, CENTER the blade in the kerf and check to be

sure that the saw teeth are not engaged into the material, If the saw blade is binding, it may walk up or Kickback from the workpiece when the saw is restarted

7 DO NOT use a dull or damaged blade, Unsharpened, improperly set, or gummed-up blades

produce narrow kerr which causes excessive friction, blade binding and Kickback

8 KEEP the blade at the correct depth setting. The depth setting should not exceed 1/4-inch

betow the material being cut (see Fig. 5). BE SURE that the blade depth and adjusting

locking levers are tight and secure BEFORE making a cut, If blade adjustment shifts while

cutting it may cause binding and Kickback,

9 USE EXTRA CAUTION when making a "Pocket Cut" into existing walls or other blind areas

The protruding blade may cut objects that can cause Kickback

I I

1 ..........................................

MAKING DEPTH-OF-CUT ADJUSTMENTS (Fig. 8)

ALWAYS use the correct blade depth setting The correct blade depth setting for all cuts should net be more than 1/4-inch below the material being cut (see Fig 5) Allowing more depth will increase the chance of kickback and cause the cut to be rough Your saw is

equipped with a deptb-oFout scale that provides increased depth-of-cut accuracy

The depth-of-cut scale is located on the inside back of the upper blade guard

Fig, B

plh-of-Cul Scate

Raise the Saw

Depth-of-CutLever \\ forAdiusting_

Lower the Saw

TO SETTHE BLADE DEPTH (Fig. 8a)

1 Unplug the saw,

,4k, WARNING: ALWAYS unplug saw before making any adjustments, Failure to

unplug the saw could result in accidental starting which can cause serious personal

injury.

2 Raise the depth-of-cut adjustment

lever to loosen the base (see Fig, 8).

3. Determine the desired depth of cut 4 Locate the depth-of-cut scale oil the

back of the upper blade guard (see Fig, 8a)

5 Hold the base of the saw flat against

the edge of the workpiece and then raise or lower the saw until the indicator

mark on the bracket aligns with the notch on the blade guard at the desired depth-of-cut mark,

6 Tighten depth-of-cut adjustment lever

Adjusting _ /

Fig_ 8a --[

) ,,,- of-t t

9, -De,,

iNIllll

USING THE LASER TRAC _ LASER LIGHT FEATLIRE (Fig. 9)

Z_ WARNING: LASER LIGHT. LASER RADIATION, Avoid Direct Eye Exposure,

DO NOT stare into beam. Only turn laser beam on when the saw is on the workpiece. Class ilia laser_

NOTE: Your circular saw has a built-in laser light. To activate laser light switch, saw must be plugged into power source.

DO NOT turn the laser beam on until the saw

is on the workpiece

Mark the line of cut on the workpiece Adjust the cutting angle and cutting depth

as needed

Plug in the saw and push the laser switch

forward to turn on the laser

Align laser beam with line-of-cut (see Fig 9)

Squeeze the trigger switch and slowly push

the saw forward using both hands Keep the red laser beam on the line-of-cut

Always shut off the laser light when you are

finished cutting

]

Fig. 9

e_nh CAUTION: The laser enhancing safety glasses that were included will

ance the laser light in bright light conditions. DO NOT wear these glasses if they

interfere with the safe operation of this saw,

LED WORKLIGHT Your circular saw has a built-in worklight for better visibility when cutting This light is always

"ON" when saw is plugged into power source

STARTING A CUT (Fig. 10)

maintain proper control of saw, Failure to clamp and support workpiece and loss of

I _ WARNING: ALWAYS clamp and support workpiece securely. ALWAYS

control of saw could result in serious injury,

1. ALWAYS use your saw with your hands positioned correctly, with one hand operating the trigger switch and the other on the front assist handle (see Fig. 10).,

and easier. Loss of control of the saw could cause an accident resulting in possible

Z_ WARNING: ALWAYS maintain proper control of the saw to make sewing safer

serious injury.

2. NEVER use the saw with your hands positioned as shown in Fig, 11

To Help Maintain Control:

3. ALWAYS support the workpiece

near the cuL

4. ALWAYS support the workpiece so the cut will be on your right.

5. ALWAYS clamp the workpiece so it will not move during the cut,, Place the workpiece with the good side down,

I NOTE: The good side of the workpiece is the side where appearance is important. ]

6. Before starting a cut, draw a guideline along

the desired line of cut, then place the front edge of the saw base on that part of the workpiece that is solidly suppoded (see Fig 10)

7. NEVER place the saw on the part of the

workpiece that will fall off when the cut

is made (see Fig. 11).

8. ALWAYS keep the cord away from the

cutting area. ALWAYS place the cord so it does not hang up on the workpiece when making a cut.

g Hold the saw firmly with both hands (see Fig 10)_

Fig. 11

z_ WARNING: If the cord hangs up on the workpiece during a cut, release the

trigger switch immediately. To avoid injury, unplug the saw and move the cord to prevent it from hanging up again.

I_ Using the saw with a damaged cord could result in serious injury

or death. If the cord has been damaged, have it replaced before using the saw again,,

+ 50 hidden pages