Craftsman 315.21636 User Manual

Owner's Manual

16 in. variablespeed

SCROLL SAW

Model No.

315.216360

Save this manual for
future reference.

A, CAUTION: Read and

follow all Safety Rules and
Operating Instructions before

first use of this product.

Customer Help Line

1-800-932-3188

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Visit the Craftsman web page: www.sears.com/craftsman

972000-707

11-99

• Safety

• Features

• Adjustments

• Operation

• Maintenance

• Parts List

(_®

NRTWC

• TableofContents...........................................................................................................................................2

• WarrantyandIntroduction..............................................................................................................................2

• RulesForSafeOperation...........................................................................................................................3-5

• Electrical.........................................................................................................................................................6

• GlossaryandProductSpecifications.............................................................................................................7

• UnpackingandToolsNeeded........................................................................................................................8

• Labels.............................................................................................................................................................9

• Features..................................................................................................................................................10-11

• Assembly.................................................................................................................................................11-12

• Adjustments.............................................................................................................................................12-15

• Operation.................................................................................................................................................16-19

• Maintenance............................................................................................................................................19-20

• Troubleshooting............................................................................................................................................20

• ExplodedViewandRepairPartsList......................................................................................................22-25

• Parts Ordering / Service ............................................................................................................................... 26

FULL ONE YEAR WARRANTY ON CRAFTSMAN SCROLL SAW
If this rRAFTSMIIH ° Scroll Saw fails due to a defect in materialor workmanshipwithinone year from the date of

purchase, Sears willrepair it, free of charge.
Contact a Sears Service Center for repair.

Ifthis product is usedfor commercialor rentalpurposes,this warrantyapplies only for 90 days from the date of

purchase.
This warranty gives you specific legal rights,and youmay also have other rightswhich varyfrom state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

Your saw has many features for making cutting
operations more pleasant and enjoyable. Safety,

performance and dependability have been given top
priority in the design of this saw making it easy to

maintain and operate,

_1_ Look for this symbol to point out important safety precautions. It means attention!!! Your

safety is involved.

_1_ WARNING:

_, CAUTION: Carefully read through this entire

owner's manual before using your new saw. Pay
close attention to the Rules For Safe Operation,

and all Safety Alert Symbols including Danger,
Warning and Caution. If you use your saw
properly and only for what it is intended, you will

enjoy years of safe, reliable service.

The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always wear

safety goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses

with side shields, available at Sears Retail Stores.

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations with them, deserve your careful attention and understanding. The safety warnings do

not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for
proper accident prevention measures,

SYMBOL

A

MEANING
SAFETY ALERT SYMBOL:

Indicates danger, warning or caution. May be used in conjunction with other symbols or picto-
graphs.

A

,&

A

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and persona_ injury.

WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, etectric shock and persona_ injury.

CAUTION: Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock

and personal injury.

Note: Advises you of information or instructions vital to the operation or maintenance of the equipment.

IMPORTANT

Servicing requires extreme care and knowledge of the system and should be performed only by a qualified
service technician. For service we suggest you return the tool to your nearest Sears store for repair. Always use

original factory replacement parts when servicing.

_, WARNING; Do not attempt to operate this tool

until you have read thoroughly and understand

completely all instructions, safety rules, etc.

contained in this manual. Failure to comply can
result in accidents involving fire, electric shock,

or serious personal injury. Save owner's manual
and review frequently for continuing safe

operation, and instructing others who may use

this tool.

_l, WARNING: Do not connect your scroll saw to a

power source until you have assembled and
adjusted the saw as described in this manual

and have read and understood all precautions
and operating instructions in the manual and
printed on the tool.

READ ALL INSTRUCTIONS

• KNOW YOUR POWER TOOL. Read the owner's
manual carefully. Learn the saw's applications

and limitations as well as the specific potential
hazards related to this tool.

• GUARD AGAINST ELECTRICAL SHOCK BY

PREVENTING BODY CONTACT WITH
GROUNDED SURFACES, For example; pipes,

radiators, ranges, refrigerator enclosures.

• KEEP GUARDS IN PLACE and in good working
order.

• REMOVE ADJUSTING KEYS AND

WRENCHES. Get in the habit of checking to see
that hex keys and adjusting wrenches are

removed from tool before turning on the saw.

• KEEP THE WORK AREA CLEAN. Cluttered
work areas and work benches invite accidents.

DO NOT leave tools or pieces of wood on the

saw while it is in operation,

• DO NOT USE IN DANGEROUS ENVIRON-

MENTS. Do not use power tools near gasoline or

other flammable liquids, in damp or wet loca-
tions, or expose them to rain. Keep the work

area well lit.

• KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a

safe distance from work area. Do not let visitors

contact tool or extension cord while operating.

• MAKE WORKSHOP CHILD-PROOF with

padlocks and master switches or by removing
starter keys.

• DO NOT FORCE THE TOOL. It will do the job

better and safer at the rate for which it was
designed.

• USE THE RIGHT TOOL. Do not force the tool or

attachment to do a job it was not designed for.
Don't use it for a purpose not intended.

RULES FOR SAFE OPERATION (Continued)

USE THE PROPER EXTENSION CORD. Make

sure your extension cord is in good condition.
When using an extension cord, be sure to use
one heavy enough to carry the current your

product will draw. An undersized cord will cause
a drop in line voltage resulting in loss of power
and overheating. A wire gage size (A.W.G) of at

_east 18 is recommended for an extension cord

25 feet or less in length. If in doubt, use the next

heavier gage, The smaller the gage number, the
heavier the cord.

• INSPECT EXTENSION CORDS PERIODI-
CALLY and replace if damaged.

• DRESS PROPERLY. Do not wear loose clothing,
gloves, neckties, rings, bracelets, or other •

jewelry. They can get caught and draw you into

moving parts. Rubber gloves and nonslip foot-
wear are recommended. Also wear protective
hair covering to contain long hair.

• ALWAYS WEAR SAFETY GLASSES WITH
SIDE SHIELDS. Everyday eyeglasses have only •

impact-resistant lenses; they are NOT safety

glasses.

• PROTECT YOUR LUNGS. Wear a face or dust

mask if the cutting operation is dusty.

• PROTECT YOUR HEARING. Wear hearing

protection during extended periods of operation. •

• SECURE WORK. Use clamps or a vise to hold

work when practical. It's safer than using your
hand and it frees both hands to operate tool.

DO NOT OVERREACH. Keep proper footing and
balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools
sharp and clean for better and safer perfor-

mance. Follow instructions for lubricating and
changing accessories.

• DISCONNECT ALL TOOLS. When not in use,
before servicing, or when changing attachments,

blades, bits, cutters, etc., all tools should be
disconnected from power supply.

• AVOID ACCIDENTAL STARTING. Be sure
switch is off when plugging in.

• USE RECOMMENDED ACCESSORIES. The

use of improper accessories may cause risk of

injury.

• NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the blade is unin-
tentionally contacted.

• CHECK DAMAGED PARTS. Before further use

of the tool, a guard or other part that is damaged

should be carefully checked to determine that it

will operate properly and perform its intended
function. Check for alignment of moving parts,

binding of moving parts, breakage of parts, saw
stability, mounting and any other conditions that

may affect its operation. A guard or other part

that is damaged must be properly repaired or

replaced by a qualified service technician at a
Sears store to avoid risk of personal injury.

DIRECTION OF FEED. Feed work into a blade
or cutter against the direction of rotation of the

blade or cutter only.

NEVER LEAVE TOOL RUNNING UNAT-
TENDED. TURN THE POWER OFF. Do not

leave tool until it comes to a complete stop,
USE ONLY CORRECT BLADES. Use the right

blade size, style and cutting speed for the
material and the type of cut. Blade teeth should
point down toward the table. Sharp blades

minimize stalling and kickback. Correctly adjust
blade tension.

TO PROTECT THE OPERATOR and minimize

blade breakage, ALWAYS adjust the hold down
foot to just clear the workpiece. Never operate

the saw with any guard or cover removed. Make
sure all guards are operating properly before

each use.

KEEP HANDS AWAY FROM CUTTING AREA.

Do not hand hold pieces so small that your

fingers go under the blade guard. Never reach

underneath work or behind, under, or within

three inches of the blade and its cutting path with
your hands and fingers for any reason. Do not

attempt to remove cut material when blade is
moving.

WARNING: Blades coast after turn off.

AVOID PINCHING THE BLADE. Be cautious
when cutting off material which is irregular in

cross section. For example, molding must lay flat
on the table and not be permitted to rock.

• DO NOT ABUSE CORD. Never yank cord to
disconnect itfrom receptacle. Keep cord from

heat, oil, and sharp edges.

• INSPECT TOOL CORDS PERIODICALLY and if

damaged, have repaired by a qualified service
technician at a Sears store, Stay constantly

aware of cord location and keep it well away

from the moving blade.

• DO NOT USE TOOL IF SWITCH DOES NOT

TURN IT ON AND OFF. Have defective switches

replaced by a qualified service technician at a

Sears store.

4

RULES FOR SAFE OPERATION (Continued)

KEEP TOOL DRY, CLEAN, AND FREE FROM
OIL AND GREASE. Always use a clean cloth
when cleaning. Never use brake fluids, gasoline,

petroleum-based products, or any solvents to
clean tool.

A LARGE PIECE OF MATERIAL SHOULD BE
SUPPORTED while cutting. To minimize risk of

blade pinching and kickback, always support
long workpieces. Saw may slip, walk or slide

while cutting long or heavy boards.
BEFORE MAKING A CUT, BE SURE ALL

ADJUSTMENTS ARE SECURE.

• BEFORE CHANGING THE SETUP, REMOVING

COVERS, GUARDS OR BLADE, UNPLUG THE
SAW.

DO NOT FEED THE MATERIAL TOO QUICKLY

while cutting. Do not force the workpiece against

the blade.

NEVER CUT MORE THAN ONE WORKPIECE

AT A TIME. If making a stacked cut, all of the
pieces must be secured to each other with

masking tape or double stick tape to make one
workpiece. Do not put more than one workpiece

on the saw table at a time. Always hold the work
firmly against the table. See page 18.

AVOID CUTTING NAILS. Inspect for and

remove all nails from lumber before cutting.

NEVER PERFORM LAYOUT, ASSEMBLY, OR
SETUP WORK ON THE TABLE while the

cutting tool is operating.
NEVER TOUCH BLADE or other moving parts

during use.

NEVER START A TOOL WHEN THE BLADE IS
IN CONTACT WITH THE WORKPIECE. Clear

thetable of debris before turningyour scrollsaw

on.

ALLOW THE MOTOR TO COME UP TO FULL
SPEED before starting a cut.

FIRMLY CLAMP OR BOLT your scroll saw to a

firm, level workbench or table. The most comfort-

able saw table height is at approximateFy hip
height.

• AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a suddenslip couldcause

yourhand to move intothe blade. ALWAYS
make sureyou have good balance. Do notcut

pieces ofmaterial that are toosmallto hold

comfortablyin your hand.

• REPLACEMENT PARTS. All repairs,whether

electrical ormechanical,shouldbe made by
qualifiedservice technicianat a Sears store or

repaircenter.

_i, WARNING: When servicing use only identical

Craftsman replacement parts. Use of any other

parts may create a hazard orcause product

damage.

• NEVER USE IN AN EXPLOSIVE ATMO-

SPHERE. Normal sparkingof the motor could
ignitefumes.

• DO NOT OPERATE THIS TOOL WHILE UN-

DER THE INFLUENCE OF DRUGS, ALCOHOL,
OR ANY MEDICATION.

STAY ALERT AND EXERCISE CONTROL.
Watch what you are doingand use common
sense. Do not operate tool when you _'e tired.

Do not rush.
MAKE SURE THE WORK AREA HAS AMPLE

LIGHTING to see the work and that no obstruc-
tionswill interferewithsafe operation BEFORE
performingany work usingyour saw.

ALWAYS TURN OFF SAW before disconnecting
it,to avoidaccidentalstartingwhen reconnecting

to powersupply. NEVER leave the scrollsaw

unattended while connected to a power source.

_L WARNING: Do not allow familiarity withyour

saw make you careless. Remember that a

careless fraction of a second is sufficientto inflict
severe injury.

SAVE THESE INSTRUCTIONS. Referto them
frequently and use to instructother users. Ifyou

loan someonethistool, loan them these instruc-
tionsalso.

SAVE THESEINSTRUCTIONS

5

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the tool's plug. When using a power tool at a consider-
able distance from the power source, use an exten-

sion cord heavy enough to carry the current that the
tool will draw. An undersized extension cord will

cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the
chart provided below to determine the minimum wire

size required in an extension cord. Only round jack-
eted cords listed by Underwriter's Laboratories (UL)

should be used.

Length of Extension Cord

Up to 25 feet

26-100 feet 16

When working with the tool outdoors, use an exten-

sion cord that is designed for outside use, This is

indicated by the letters WA on the cord's jacket.

Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.

_ CAUTION: Keep the cord away from the cutting

area and position the cord so that it will not be
caught on lumber, tools, or other objects during

cutting.

Wire Size (A.W.G.)

18

ELECTRICAL CONNECTION

Your Sears Craftsman Scroll Saw is powered by a
precision built electric motor. It should be connected

to a power supply that is 120 volts, 60 Hz, AC only

(normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will

cause a loss of power and the motor will overheat. If
the saw does not operate when plugged into an outlet,

double check the power supply.

GROUNDING INSTRUCTIONS

in the event of a malfunction or breakdown, grounding

provides a path of least resistance for electric current
to reduce the risk of electric shock. This tool is

equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug

must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local

codes and ordinances.

Do not modify the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified
electrician. Improper connection of the equipment-

grounding conductor can result in a risk of electric
shock. The conductor with insulation having an outer

surface that is green with or without yellow stripes is
the equipment-grounding conductor. If repair or

replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to
a live terminal.

Check with a qualified electrician or service personnel
if the grounding instructions are not completely

understood, or if in doubt as to whether the tool is
properly grounded.

Repair or replace a damaged or worn cord immedi-

ately.
This tool is intended for use on a circuit that has an

outlet like the one shown in Figure 1. It also has a
grounding pin like the one shown.

GROUNDING

PIN COVEROF GROUNDED

OUTLETBOX

Fig. 1

Bevel Cut
Acutting operation made withthe table at any angle

otherthan 90°to the blade.

Crosscut

A cutting or shaping operation made across the grain

of the workpiece.
Compound Cut

A compound cut is a cut made using a miter angle
and a bevel angle at the same time.

Freehand (for scroll saw)
Performing a cut without the workpiece being guided

by a fence or miter gage. Work must supported by the

table.

Gum

A sticky, sap based residue from wood products.

Kerf

The material removed by the blade in a through cut or
the slot produced by the blade in a nonthrough or

partial cut.

Leading End

The end of the workpiece pushed into the cutting tool
first.

Nonferrous Metal

Metal that does not contain iron; such as aluminum,

brass, and copper.

Push Stick
A device used to feed the workpiece through the saw

blade during narrow ripping type operations and helps
keep the operator's hands well away from the blade.

Resaw

A cutting operation to reduce the thickness of the
workpiece to make thinner pieces.

Resin

A sticky, sap base substance that has hardened.

Ripping

A cutting operation along the length of the workpiece.
Saw Blade Path

The area directly in line -- over, under, behind, or in
front of the blade. As it applies to the workpiece, that

area which will be, or has been, cut by the blade.
Set
The distance that the tip of the saw blade tooth is bent

(or set) outward from the face of the blade.

SPM

Strokes per minute. Used in reference to blade
movement.

Throw-Back

Throwing of a workpiece in a manner similar to a

kickback. Usually associated with a cause other than

the kerf closing, such as a workpiece not being

against the fence, being dropped into the blade, or
being placed inadvertently in contact with the blade.

Through Sawing
Any cutting operation where the blade extends

completely through the thickness of the workpiece.

Workpiece
The item on which the cutting operation is being done.
The surfaces of a workpiece are commonly referred to

as faces, ends, and edges.
Worktable
The surface on which the workpiece rests while

performing a cutting or sanding operation.

Throat

Motor
Drive

Blade Length

Table Size

16 in. Table Tilt 45 ° right and 10" left

120 V, 1.2 amp 60 HZ-AC only Overall Dimensions 12-1/4 in. W

Variable Speed 25-1/4 in. L

500-1600 Strokes per minute 14 in. H

Net Weight 28 Ibs.

5 in. plain or pin

10-5/8 in. x 18-3/4 in.

7

_lj WARNING: To prevent accidental starting or

electrical shock that could cause possible

serious personal injury, assemble all parts to

your saw before connecting it to power supply.

Saw should never be connected to power supply

when you are assembling parts, making
adjustments, lubricating, installing or removing.

blades, cleaning, or when not in use.

Carefully lift saw from the carton and place it on
a level work surface.

Remove pack of 2 extra blades and owner's

manual from the carton.

_, WARNING: If any parts are missing, do not

operate this tool until the missing parts are
replaced. Failure to do so could result in possible

serious personal injury.

The following tools (not included) are needed for
adjustments and alignment:

• Small Combination Square

• Adjustable wrench

• Flatblade Screwdriver

• Do not discard the packing materials until you
have carefully inspected the saw, identified all

parts, and satisfactorily operated your new saw.

Note: If any parts are damaged or missing, do not
attempt to plug in the power cord and turn the switch
on until the damaged or missing parts are obtained

and are installed correctly.
Your scroll saw comes completely assembled. A

package of 2 extra blades and an owner's manual are
included with your saw.

SMALL

COMBINATION

SQUARE

FLATBLADESCREWDRIVER

Fig. 2

The following labels are on the scroll saw with locations indicated.

WARNING

ON OFF

a

CRRFTSMRN°

ConsumerHelp Line 1-800-932-3188

WARNING / ADVERTENCIA

Fig. 3

Thisversatilevariablespeedscrollsawisgreatfor

makingtoys,puzzles,games,artwork,andjewelry.It
isahandydo-it-yourselftool.Itcutswood,wood

compositionproducts,plastic,andotherfibrous
materialupto2 inchesthick.Italsocutsnonferrous

metals(aluminum,brass,copper).

KNOW YOUR SCROLL SAW

Before attempting to use your saw, familiarize yourself
with all operating features and safety requirements of

your Sears Craftsman scroll saw. See Figure 5.

ON/OFF KNOB WITH VARIABLE SPEED

Your scroll saw has an easy access ON/OFF knob
with variable speed. Pull the knob out to turn ON the

saw, and push the knob in to turn OFF the saw. Turn
the knob to adjust the speed from the high speed of
approximately 1600 SPM (Strokes Per Minute) to the

low speed of approximately 500 SPM.

LOCK OFF POST

Place a pad lock in the lock post next to the ON/OFF

knob to lock the saw in the OFF position to prevent
unauthorized use of the saw by children or others.

TOOLLESS BLADE HOLDERS

Retain and position the blade without the use of
additional tools. Use the knobs for plain end blades or
use the designed slots for pin type blades.

TENSION QUICKRELEASE

ADJUSTING KNOB

KNOB

AIRDIAPHRAGM

BLADE

,STORAGE

DRAWER

Fig. 4

BLADE STORAGE DRAWER

Attached under the left side of the table is a blade
storage drawer. It will hold up to 20 blades. Drawer
snaps closed securely, See Figure 4.

BLADE TENSION KNOBS

Blade tension is controlled by a dual knob tension
control system. The inner (smaller) knob, tension
adjusting knob, is for making adjustments of the blade

tension. The outer (larger) knob, quick release knob,
is used to quickly set and release blade tension to

facilitate blade changes.

HOLD DOWN FOOTLOCK KNOB

MOTOR

LOCKOFF POS1

ON/OFF KNOB

PLAINENDBLADEKNOB

HOLDDOWNFOOT/

BLADEGUARD

SAWBLADE

,SAWTABLE

BLADE STORAGE DRAWER

BEVEL ADJUSTMENTKNOB

Fig. 5

10

HOLD DOWN FOOT/BLADE GUARD
The hold down foot should be lowered until itjust
rests on top Ofthe workpieoe to prevent the workpieco

from lifting while cutting, but not so much that the
workpiece drags. The vertical portion provides e blade

guard to prevent accidental blade contact.

HOLD DOWN FOOT LOCK KNOB

Allows you to raise or lower the hold down foot/blade

guard and secure it at desired heights.

SAWDUST BLOWER
Keeps the line of cut on workpiece clean for more

accurate scroll cuts.
SAWDUST EXHAUST

Your saw has a sawdust exhaust that fits a standard

shop vacuum hose. See Figure 13.

SAW TABLE

Your scroll saw has an aluminum saw table that

provides a working surface to support your workpiece.

TABLE LOCK KNOB

Allows you to tilt the table end lock it at the desired

angle up to 45 degrees.

BEVEL SCALE

The bevel scale and indicator are located on the front
of the saw for easy viewing. They show the angle of

the table.

ZERO DEGREE STOP FOR TABLE

Located under the front of the saw table, the zero

degree stop allows easy return and fine adjustment of
the zero degree relationship between the table and

the blade.

Your Craftsman 16 in. scroll saw was fully assembled

at the factory. Before operating this tool, it is important
to check all alignments and settings. Normal handling
during shipment may have changed settings.

_1_ WARNING: To avoid serious personal injury

from unexpected tool movement, always

securely mount scroll saw to a workbench.

MOUNTING SCROLL SAW TO
WORKBENCH

See Figure 6.

If the scroll saw is to be used in a permanent applica-
tion, we recommend that you secure it in e permanent
location such as a workbench. When mounting the
saw to a workbench, holes should be drilled through
the supporting surface of the workbench using dimen-

sions i_lustrated.

• Each hole in the base of the saw should be
bolted securely using 5/16 in. diameter machine

bolts, lock washers, and hex nuts (not included).
Bolt should be of sufficient length to accommo-
date the saw base, lock washers, hex nuts, and

the thickness of the workbench.

• Locate end mark the holes where scroll saw is to

be mounted.

• Drill (3) 3/8 in. diameter holes through work-
bench.

• Place scroll saw on workbench aligning holes in

the base with holes drilled in the workbench.

• Insert all three 5/16 in. bolts and tighten securely

with lock washers and hex nuts.

Note: All bolts should be inserted from the top. Install
the lock washers and hex nuts from the underside of

the bench.

Supporting surface where scroll saw is mounted
should be examined carefully after mounting to insure
that no movement during use can result. If any tipping

or walking is noted, secure workbench or supporting

surface before beginning cutting operations.

9

24 in.

3/8 in.dia,

6 5/8 in

q4_1_ in. 19in.

12in.

11

Fig. 6

CLAMPING SCROLL SAW TO
WORKBENCH

See Figure 7.

If the scroll saw is to be used in a portable application,

we recommend that you fasten it permanently to a

mounting board that can easily be clamped to a
workbench or other supporting surface. The mounting

board should be of sufficient size to avoid tipping of
saw while in use.

• Mount saw to board using holes in frame as a
template for hole pattern or the diagram in

Figure 6. Locate and mark the holes where scroll

saw is to be mounted.

• Follow last three steps in previous section called

Mounting Scroll Saw to Workbench.

Make sure mounting bolts are long enough to go
through holes in the saw frame, material being

mounted to, lock washers, and hex nuts.
Note: It may be necessary to countersink hex nuts

and washers on bottom side of mounting board.

\

C-CLAMP

MOUNTING

BOARD

C-CLAMF

WORKBENCH

Fig. 7

_1, WARNING: To prevent accidental starting that

could cause possible serious personal injury,
turn off the saw and unplug before making any
adjustments.

HOLD DOWN FOOT/BLADE GUARD

See Figure 8.

The hold down should be adjusted so it contacts the
top surface of the work being cut. Tighten adjusting

knob after adjustment has been made.

• Loosen the hold down foot lock knob.

• Move the hold down foot to the desired position.

• Tighten the hold down foot lock knob.

The tall, front part of the hold down foot acts as a

blade guard to prevent accidental contact with the

blade.

SAWDUST BLOWER

See Figure 8.

The dust blower is designed and preset to direct air to
the most effective point on the cutting line. Be sure

hold down foot is properly adjusted to properly secure
workpiece and to properly direct air to the cutting

surface.

• Insert hose to air diaphragm before starting the
saw.

AIR DIAPHRAGM

HOLD DOWN FOOT

BLADE

AIR HOSE

\

Fig. 8

12

SQUARING TABLE TO THE BLADE

See Figures 9 and 10.

• Loosen the hold down foot lock knob and move
hold down rod all the way up. Tighten knob.

• Loosen the table lock knob and move the table
untit it is approximately perpendicular, or at right

angle to the blade.

• Place a small square on the table next to the
blade to check if the table is 90 degrees to the

blade. If adjustment is needed, raise or lower the

table until table is approximately go degrees to
the blade and securely tighten the table lock

knob.

Loosen the screw holding the scale indicator,
move indicator to the 0 degree mark and se-

curely tighten screw. Remember, the bevel scale
is a convenient guide but should not be relied

upon for precision. Make practice cuts on scrap
materiat to determine if your angle settings are
correct.

• Adjust the hold down foot to desired position and
securely tighten the hold clown foot knob.

HOLDDOWNROD

HOLDDOWNFOOT

SETTING THE TABLE FOR HORIZONTAL
OR BEVEL CUTTING

See Figures 10, 11 and 12.

A bevel scale is provided under the work table as a
convenient guide for setting the approximate table

angle for bevel cutting. When greater precision is

required, make practice cuts on scrap material and

adjust the table as necessary for your requirements.
An adjustable zero degree stop is provided to quickly

return the table to the zero degree setting.

• Loosen the table lock knob and push down on
the right side of the table. If the table stops at 0 °,
the zero degree stop is properly set. If the table

stops somewhere other than zero, then adjust
the zero degree stop.

ZERODEGREE II /

COMBINATION

SQUARE

HOLDDOWN

FOOT/

BLADEGUARD

SAW BLADE

TABLELOCK

KNOB

Fig. 9

SCALe

_ __ INDICATOR

TABLE LOCK SCREW

KNOB Fig. 10

• To access the zero degree stop, loosen the table
lock knob, and tilt the table with the right side all
the way down. Just under the front of the saw

table is the zero degree stop. See Figure 1I.
Loosen the hex nut and rotate the hex bolt to

raise or lower the bolt as needed to adjust the
zero degree stop. Be sure to check to see that

the table is square to the blade.

Now, by returning the table to the zero position, the
zero degree stop provides a quick reference to the
preset position.

13

HEX BOLT SAWTABLE

HEXNUT

ERODEGRE

STOPASSEMBLY

Fig. 11

The zero stop assembly can be rotated to the left and
down out of the way and the table can be angled up to

12' to the left. See Figure 12.

Note: Make sure the zero degree stop is rotated all
the way down or it will contact the blade storage

drawer as you angle to the left.

• On the top back of the saw, rotate the quick
release knob to the left or counterclockwise to

loosen blade tension. See Figure 5.

• Remove the throat plate.

• Place blade through the throat plate opening with

the teeth of the blade to the front of the saw and
pointing down toward the table. Engage the pin

into the "V" notch of the lower blade holder.

• Pull up on the blade and push down on the saw

arm to engage the upper pin in the "V" notch of

the upper blade holder.
Note: If the blade touches the hold down foot on
either side then the hold down foot must be adjusted.

• Loosen the foot adjusting knob. See Figure 13.

• To center the hold down foot around the saw

blade, slide the hold down foot to the side.

• Tighten the foot adjusting knob.

• To tension the blade, rotate the quick release

knob (outer, larger knob) 1/4 turn to the right or

clockwise to apply tension to the blade. Fine

adjustments of the blade tension may be per-

formed using the tension adjusting knob (inner,

smaller knob) at any time, while the blade is
under tension or not.

• Replace throat plate.

Plain End Blades

See Figure 13.

• Turn off and unplug the saw from outlet.

Fig. 12

INSTALLING BLADES

Scroll saw blades wear out quickly and must be
replaced frequently for best cutting results, Expect to

break some blades while you learn to use and adjust
your saw. Blades generally stay sharp for 1/2 hour to
2 hours of cutting, depending on type of material and
speed of operation.

Pin End Blades

See Figure 13.

• Turn oft and unplug the saw from outlet.

_l, WARNING: To avoid injury from accidental

starting, always turn off and unplug the saw
before installing, removing or replacing the

blade.

_. WARNING: To avoid injury from accidental

starting, always turn off and unplug the saw
before installing, removing, or replacing the

blade.

• On the top back of the saw, rotate the quick
release knob to the left or counterclockwise to

loosen the blade tension. See Figure 5.

• Remove the throat plate.

• Loosen the blade knobs by hand and remove the
blade.

• Place new blade through the throat plate opening
in the table with the teeth of the blade to the front

of the saw and pointing down toward the table.
Next, place blade in the lower blade holder into

the slot that enlarges as you loosen the blade
knob.

• Position blade and securely tighten blade knob.

• Pull up on the blade and down on the saw's

upper arm to install blade into upper blade
holder.

Note: If the blade touches the hold down foot on

either side then the hold down foot must be adjusted.

14

Loosenthefootadjustingknob.See Figure 13.

To center the hold down foot around the saw
blade, slide the hold down foot to the side.

Tighten the foot adjusting knob.
Position blade and securely tighten blade knob.

Turn the quick release knob to the right or
clockwise to tension the blade.

Turn the tension adjusting knob to the right,
clockwise or to the left, counterclockwise until the

blade is in desired tension. • Turn tension adjusting knob (upper, smaller

• Replace throat plate, knob) to the right or clockwise to increase

PLAIN END BLADE decrease blade tension.

-- _ FOOT ADJUSTING
_ll,_.L PLAIN =ND KN Note: Adjustments of blade tension can be made at

QUICK _ I I | I

,o,,.,,,, ,o,,o,o,

tension. Turn it to the left or counterclockwise to

leased or engaged while making adjustments with the
tension adjusting knob.

Fig. 14

__ anytime. The quick release knob can be either re-

PIN ENDBLADE

| "_ HOLD DOWN FOOT TO DECREASE TO INCREASE
:1 SAWBLADE TENSION TENSION

TENSIONADJUSTING KNOB

PLAINEND

BLADEKNOB

• Rotate quick release knob to the right or clock-

SAWDUST

©

EXHAUST

ADJUSTING BLADE TENSION

See Figures 14and 15.

• Turn off and unplug the saw.

_k WARNING: Failure to unplug your saw could

result in accidental starting causing possible

serious personal injury.

Tension adjusting knob is on the top of the saw.

See Figure 5. Rotate the quick release knob
(outer, larger knob) 1/4 turn to the left or counter-

clockwise to release blade tension.

®

Fig. 13

wise 1/4 turn to engage tension before using the

scroll saw.

Check tension by the sound the blade makes when
plucked like a guitar string. This method of adding

tension to the blade can be developed with practice

and requires knowing your scroll saw.

• Pluck the back straight edge of blade while
turning tension adjusting knob. Sound should be

a musical note. Sound becomes less flat as
tension increases. Sound decreases with too

much tension.

Note: Be careful not to over tension the blade. Too
much tension may cause blade to break as soon as

you start cutting. Too little tension may cause blade to

bend or break before teeth wear out.

Fig. 15

15

This scroll saw is designed to cut wood, wood compo-
sition products, plastic, and nonferrous metals (alumi-
num, brass, copper).

GENERAL OPERATION

Please read and understand the following items
concerning your scroll saw before attempting to use

the saw.

• There is a learning curve for each person who
wants to use this saw. During that period of time
it is expected that some blades will break until

you learn how to use and adjust the saw.

• Allow the saw to cut material by guiding the
workpiece into the blade as it moves. Do not
force the work.

• The blade teeth cut material only on the down
stroke.

You must guide the workpiece into the blade
slowly because the teeth of the blade are very

small and can only remove material on the down
stroke.

• Scroll saw blades wear out and must be replaced
frequently for best cutting results. Scroll saw

blades generally stay sharp for 1/2 hour to 2
hours of cutting, depending on type of material

and speed of operation.

• To get accurate cuts, be prepared to compen-
sate for the blade's tendency to follow the wood
grain as you are cutting wood.

• In cutting wood, best results are achieved when
cutting wood less than one inch thick.

• When cutting wood thicker than one inch, the
user must guide the workpiece very slowly into

the blade and take extra care not to bend or twist
the blade while cutting.

• When choosing a blade to use with your scroll
saw, consider the following carefully:

• Very fine, narrow blades should be used to

scroll cut in thin material 1/4 in. thick or less.

Most blade packages state the size or thick-
ness and type of material which that blade is

intended to cut. Package should also state the

radius, o_size of curve, which can be cut with

that blade.

• Wider blades cannot cut curves as tight or

small as thinner blades.

• Blades wear faster:

• When cutting plywood and other laminates.

• When cutting material thicker than 3/4 in.

• When cutting hardwood.

• When side pressure is applied to the blade.

ON/OFF KNOB WITH VARIABLE SPEED

See Figure 16.

Your scroll saw has an easy access On/Off knob with
variable speed.

• Pull the knob out to turn ON the saw, and push
the knob in to turn OFF the saw.

Note: After saw is turned on, a hesitation before blade
movement is normal.

_IL WARNING: Never leave the saw unattended

until the blade has come to a complete stop to
prevent serious personal injury.

LOCK
POST

ON/OFFKNOB

Fig. 16

• By turning the knob, the variable speed control
may be adjusted from the high speed of approxi-
mately 1600 SPM (Strokes Per Minute) to the

low speed of approximately 500 SPM Suggested
speeds are identified under Choice of Blade and
Speed, page 18. Turn the On/Off knob to the

right or clockwise to increase strokes per minute
and to the left or counterclockwise to reduce the

strokes per minute.

This motor has an electronic control that regulates the

speed and provides overload protection to the motor.
If the motor fails to start after about 2 seconds, push

the knob OFF and disconnect the saw from the power

source. Refer to the troubleshooting chart.
Note: If the internal overload protector has been

tripped, pushing the On/Off knob OFF will reset it.

16

LOCK POST

See Figure 17.

To prevent unauthorized use of your scroll saw, we
suggest that you disconnect it from the power supply

and lock the knob in the OFF position. A Master
Lock® 105D padlock should be used. When the lock

is installed and locked, as illustrated, the switch is
inoperable. Store the padlock key in another location.

• To lock the saw in the OFF position, install a
padlock through the lock post beside the knob as

illustrated and lock the padlock. (Padlock is not
supplied with the saw.)

_lb WARNING: For your own safety, always push

the knob OFF when machine is not in use. Also,
in the event of a power failure, push knob OFF.

Lock the scroll saw switch OFF with a padlock.
This will prevent the machine from starting up

again when the power comes back on. Failure to
heed this warning can result in serious personal

injury.

o

INTERIOR SCROLL CUTTING

See Figure 18.

• One of the features of a scroll saw isthat it can
be usedto make scrollcutson the interior of a

board withoutbreakingor cuttingthroughthe
edge or perimeterof the board.

WARNING: To avoid possible serious injury

,&

from accidental starting, always turn the switch
OFF and remove plug from power source outlet
before removing or replacing the blade.

• To make interior cuts ina board, remove the
scroll saw blade as explained in the Installing
Blades section on page 14.

• Drill a 1/4 in. hole in the board to be used to
make interior cuts.

• Place the board on the saw table with the hole in
the board over the access hole in the table.

• Install blade through hole in board then adjust
the hold down foot and the blade tension. See

pages 14 and 15.

• When finished making the interior scroll cuts,
simply remove the blade from the blade holders

as described in the Installing Blades section,
and remove the board from the table.

ON/OFFKNOB =__ _ _

DRILLHOLE

INTERIOR

CUT

Fig. 17

Fig. 18

17

STACK CUTTING

See Figure 19.

After becoming well acquainted with your saw through
practice and experience, you may wish to try stack
cutting. Stack cutting may be used when several
identical shapes need to be cut. Several pieces of

wood may be stacked on top and secured to each
other before cutting. The wood pieces may be joined

together by placing double sided tape between each
piece or by wrapping masking tape around the
corners or ends of the stacked wood. You must attach

the stacked pieces of wood to each other so they will
move on the table as a single piece of material.

_I, .WARNING:. To avoid possible, serious personal

injury, do not cut more than one loose piece of
material at a time.

TAPE

CHOICE OF BLADE AND SPEED

Fig. 19

The scroll saw accepts a wide variety of blade widths and thicknesses for cutting wood and other fibrous materi-
als. Your saw uses 5 inch long blades of either the pin end or the plain end style. The blade width and thickness
and the number of teeth per inch to use are determined by the type of material and the size of the radius being

cut. A full selection of scroll saw blades are available through Sears Retail Stores.

Note: As a general rule, always select narrow blades for intricate curve cutting, and wide blades for straight and

large curve cutting.

Speed or

Teeth/Inch

Width

Thickness

Strokes Per Material Cut

Minute

10

.110in.

.020 in.

1200-1600

Popular size for cuttinghard and soft
woods3/16 in. up to 2 in. Plastics,paper,

felt, bone, etc.

15

.110in.

.020 in.

600-1200

Wood, plastics, extremely thin cuts on
materials 3/32 in. to 1/2 in. thick.

18

BEFORE EACH USE:

• INSPECT YOUR SAW. Disconnect the saw. To
avoid injury from accidental starting, turn the

switch OFF and unplug the saw before changing
the setup or removing covers, guards, or blade.

• INSPECT YOUR WORKPIECE. Make sure there

are no nails or foreign objects in the workpiece to

be cut.

• USE EXTRA CAUTION WITH LARGE, VERY

SMALL, OR AWKWARD WORKPIECES.

• Never use this tool to cut pieces too small to hold

by hand.

.095in.

.010 in.

500-600

• Always use extra supports (tables, saw horses,

• Never use another person as a substitute for a

• When cutting an irregularly shaped workpiece,

For tight radius work in thin materials
3/32 in. to 1/8 in. wood, veneer, bone,

fiber, ivory, plastic, etc.

blocks, etc.) for any workpiece large enough to
tip when not held down to the table top.

table extension, or as additional support for a
workpiece or to help feed, support, or pull the
workpiece.

plan your work so it will not pinch the blade. A
piece of molding, for example, must lay flat or be

held by a fixture or jig that will not let it twist,
rock, or slip while being cut.

18

Properlysupportroundmaterialsuchasdowel
rods.Theyhaveatendencytorollduringacut,
causingthebladeto"bite."Toavoidthis,always

usea"v"block.

• Cleareverythingexcepttheworkpiece and

related support devices off the table before
plugging into power and turning the saw on.

• PLAN THE WAY YOU WILL HOLD THE

WORKPIECE FROM START TO FINISH. Do not
hand hold pieces so small that yourfingerswill

go under the work hold-down.

• BEFORE FREEING ANY JAMMED MATERIAL:

• Turn switch OFF.

• Wait for all moving parts to stop.

• Unplug the saw.

,_ WARNING: When servicing, use only identical

Craftsman replacement parts. Use of any other
part may create a hazard or cause product
damage.

WHEN BACKING OUT OF THE WORKPIECE,
THE BLADE MAY BIND IN THE KERF (CUT).
THIS IS USUALLY CAUSED BY SAWDUST

CLOGGING UP THE KERF. IF THIS HAPPENS:

• Turn switchOFF.

• Wait for all moving parts to stop.

• Unplugthe saw.

• Remove the blade from the blade holders.

• Remove the workpJece with blade from the table.

• Remove blade from workplace.

_i, WARNING: Before removing _oosepieces from

the table, turn saw off and wait for all moving
parts to stop to avoid serious personal injury.

BRONZEBEARING

_. WARNING: To prevent accidental starting that

could cause possible serious personal injury,
turn off and unplug the saw before maintaining or

lubricating your scroll saw.

GENERAL MAINTENANCE

• Keep your Scroll Saw clean.

• After cleaning the table top initially, apply a thin
coat of automobile type (paste) wax to the table

top so the wood slides easily while cutting.

ARM BEARINGS

See Figure 20.

Lubricate the arm bearings after every 50 hoursof
use or whenever there is a squeak coming from the

bearings.

• Carefully place the saw on its side as shown in
Figure 20. Remove the rubber cap from the

lower arm of the saw.

• Squirt a few drops of SAE20 oil around the shaft

end and bronze bearing. Let oil soak in over-

night, remaining in this position.

Note: Lubricate the upper arm bearing from the other

side of the saw.

,_IL WARNING: Ifthe power cord is worn, cut, or

damaged in any way, have it replaced
immediately by a quatified service technician at a
Sears store to avoid risk of personal injury.

MOTOR BRUSHES

See Figure 21.

Your saw has externally accessible brush assemblies
that should be checked periodically for wear. When
one of the two brushes becomes worn, replace both

brushes.

• Unplug your saw.

_l, WARNING: Failure to unplug yoursaw could

result in accidental starting causing serious
injury.

19

• Remove brush cap with a flat blade screwdriver.

• Remove brush assembly. Gently pry the brush
assembly out using a small screwdriver, point of
a nail or paper clip, etc.

• Check for wear. If one brush is worn down

shorter than 1/4 in., replace both brushes. Do
not replace one side without replacing the other.

• Reassemble using new brush assembly. Make

sure curvature of brush matches curvature of
motor and that brush moves freely in brush tube.
Use the blunt end of something thin (eraser end

of pencil, etc.) to push the brush into the tube

until it stays.

• Make sure brush cap is oriented correctly

(straight) and replace.

• Tighten brush cap using a hand powered screw-

driver only. Do not overtighten.

• Repeat for other brush.

_i, WARNING: For your own safety, turn switch OFF and remove plug from power outlet before adjusting or

aligning your scroll saw.

\

#pBRUSHCAP

Fig. 21

PROBLEM CAUSE SOLUTION

Motor will not run. 1. Problemwith ON-OFF switch, 1.

power cord, or outlet.

2. Motor Defective. 2.

Blades breaking. 1. Too much tension. 1. Adjust tension.

2. Feeding too quickly. 2. Reduce feed rate.

3. Wrong blade. 3.

4. Blade twisting in wood. 4.

Vibration (there is always 1. Improper mounting of saw. 1. Check mounting.
some vibration when the saw 2. Mounting surface. 2. Check mounting in manual.

is running). 3, Loose table or table resting 3. Tighten table lock knob.

against motor.

4, Loose motor mounting. 4. Tighten mounting screws.

Blade runout (blade not 1, Blade holders out of line. 1. Realign blade.
properly aligned with arm

motion).

Have worn parts replaced before using
Scroll Saw again. Have the proper

outletinstalled bya qualified electri-
cian.

Do notattempt any repair. Have
repaired by a qualified servicetechni-
cian at a Sears store or repaircenter.

Narrow blades for cuttingthinwood or
tightcorners and turns, wide blades for

thickerwood orwideturns.

Reduce side pressure on blade, check
blade tension.

20

21

CRAFTSMAN SCROLL SAW- MODEL NO. 315.216360

7

16

25

19

39

40

FIGURE A

42

37

i

i

I

36 _36

45

46

23

24

53_ __

52

Po
G_

Key
No.

11
12
13

14

15

16

17
18
19

20
21
22

23
24
26

26
27
28

1
2
3
4
5

6
7
8
9

Part
Number

979817-002
980119-001
979814-001
979813-001

979832-001
981385-001

979809-001
979807-001

979806-001

**STD851005

979805-001

**STD851006

979803-002
979802-001

980123-001
979777-001
979788-001
979786-001

979785-001
979784-001
979775-001

979776-001
979774-001

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216360

PARTS LIST FOR FIGURE A

Description Quan.

Blade Lock Knob ........................................... 1

Blade Holder ................................................. 1

Spring Pin ..................................................... 1

Spring Pin ..................................................... 1

Saw Blade ..................................................... 1

Throat Plate .................................................. 1

Table ............................................................. 1

Table Screw .................................................. 1

Blade Drawer ................................................ 1

Blade Drawer Bracket ................................... 1

Washer (M5) ................................................. 3

Screw (M5 X 8 Pan Hd.) ............................... 3

Screw (M5 X 8 Pan Hd.) ............................... 2

Bevel Lock Knob ........................................... 1

Flat Washer (M6) .......................................... 2

Scale ............................................................. 1

Miter Scale Bracket ...................................... 1

Motor (Includes Key Nos. 21,22, 23, & 24) . 1

Motor Screw ............................................... :.. 3

Clamp Screw ................................................ 2

Brush Holder ................................................. 2

Brush Assembly ............................................ 2

Brush Cap ..................................................... 2

Counterbalance ........................... ................. 1

Clamp Screw ................................................ 1

Spacer .......................................................... 1

Screw (M5 X 15 Pan Hd.) ............................. 1

Key Part
No. Number

29 979772-001
30

31 **STD840508
32 979822-001

33 979823-001
34 979824-001
35 979825-001
36 981367-001

37 979771-002
38 **STD833020
39 979768-001

40
41 979766-001
42 979767-001

43 979801-001
44 979800-001

45 979799-001
46 979798-001
47 979797-002

48 979796-001
49 979794-001
50 979793-001
51 979795-001

52 979790-001
53 979791-001

54

Description Quan.

Indicator ........................................................ 1

Hex Bolt (M5 X 15) ....................................... 1

Hex Nut (M5) ................................................ 1

Hex Bolt (Socket Hd. Special) ...................... 1

Washer ......................................................... 1

Stopper ......................................................... 1

Spring Pin ..................................................... 1

Rubber Feet .................................................. 3

Base .............................................................. 1

Hex Bolt (M6 X 20) ....................................... 4

Warning Label ............................................... 1

Hex Bolt (M5 X 16) ....................................... 3

Screw (Pan Hd.) ........................................... 2

Nozzle ........................................................... 1

Screw (Pan Hd.) ........................................... 2

Control Box ................................................... 1

PC Board Assembly ............... ,..................... 1

Gasket .......................................................... 1

On/Off Knob .................................................. 1

Knob Label .................................................... 1

Motor Pointer ................................................ 1

Switch Label ................................................. 1

Motor Cover .................................................. 1

Power Cord Assembly .................................. 1

Strain Relief ................................................... 1

Screw (M6 X 10 Pan Hd.) ............................. 4

* Standard Hardware Item - May Be Purchased Locally ** Available From Division 98 - Source 980.00

*** Complete Assortment Available At Your Nearest Sears Retail Store

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216360

29

37

38

12

39

ro
J_

14

12

40

"26

20

24

18

42

15

14

FIGURE B

I

CRAFTSMAN SCROLL SAW- MODEL NO. 315.216360

The model numberwillbefoundon a plate attached tothe frame. Always mentionthemodel number inall correspondenceregardingyour SCROLL |

SAW orwhen orderingrepairparts.

[

PARTS LIST FOR FIGURE B

I

J

Key Pad
No. Number

1 979827-002

2 979737-001

3 979736-002
4 979742-001
5 979735-001
6 979756-001

7 979734-001
8 979828-001

ro

ol

9 979733-001

10 979830-001
11 979732-001
12 979765-001

13 979763-001
14 979764-001
15 979814-001

16 979813-001
17 980119-001
18 979817-002

19 979762-001

20 **STD852005

21 979761-001
22

Description Ouan.

Tension AdjustingKnob ................................ 1

Spring Pin ..................................................... 1

Quick Release Knob..................................... 1

RubberBoot.................................................. 1

Cam .............................................................. 1

Arm Spring.................................................... 1

TensionWedge ............................................. 1

Washer ......................................................... 1

Tension Bolt.................................................. 1

E-Ring ........................................................... 1

TensionWedge ............................................. 1

Bushing......................................................... 4

LowerArm .................................................... 1

Spacer Bearing............................................. 2

SpringPin ..................................................... 1

Spring Pin ..................................................... 1

Blade Holder ................................................. 1

Blade Lock Knob........................................... 1

Link ............................................................... 1

SpringWasher (M5) ..................................... 2

Screw (Socket Hd. Cap) ............................... 1

Washer (M4) ................................................. 2

Key Pad

No. Number
23 979759-001
24 979758-001

25
26 979752-001

27 979751-001
28
29 981386-001

30 979741-001
31 979831-001
32 979744-002

33 979745-001
34 979749-001

35 979743-001
36 979747-001
37 979746-001

38 979748L001
39 979753-001

40 979754-001
41 979755-001

42 979757-001
43 979829-001

972000-707

Description Ouan.

Screw (Pan Hd.) ........................................... 2

BallBearing .................................................. 2

Bolt(M5 X 18 Hex Hd.) ................................. 1

RightArm Cover ........................................... 1

Spring Pin ..................................................... 1

Screw (M4 X 30 Pan Hd.) ............................. 8

Data Plate ..................................................... 1

Hold Down Foot Lock Knob.......................... 1

Support Bar Assembly.................................. 1

FootAdjusting Knob ..................................... 1

Support Plate ................................................ 1

Hold Down Clamp ......................................... !

Washer/Spacer ............................................. 1

Hold Down Foot............................................ 1

Air Hose ........................................................ 1

Air Diaphragm............................................... 1

Upper Arm .................................................... 1

Hand Warning Label ..................................... 1

Left Arm Cover.............................................. 1

Logo Plate ...................... '............................... 1

RubberStopper ............................................ 3

Owners Manual

* Standard Hardware Item -- May Be Purchased Locally

** Available From Division 98 - Source 980.00

In U.S.A. or Canada

for in-home major brand repair service:

Call 24 hours a day, 7 days a week

1"800-4-MY-HOME s°(1-800-469-4663)

Para pedir servicio de reparacibn a domicilio - 1-800-676-5811

Au Canada pour tout le service ou les pi_ces - 1-800-469 4663

For the repair or replacement parts you need:

Call 6 a.m. - 11 p.m. CST, 7 days a week

Parts Direct s_

1-800-366-PART (1-800-366-7278)

Para ordenar piezas con entrega a domicilio - 1-800-659-7084

For the location of a Sears Service Center in your area:

Call 24 hours a day, 7 days a week

1-800-488-1222

To purchase or inquire about a Sears Maintenance Agreement:

Call 7 a.m. - 5 p.m. CST, Monday - Saturday

1-800-827-6655