![](/html/08/080a/080a69bd1c38645784bb3cc0c2abefa30608de98040e143d8c924025af54affa/bg1.png)
Operator's Manual
I:RRFTSMRN
ACCESSORIES FOR MODEL NO. 212400
10 in. (254 mm) COMPOUND MITER SAW
Save this manual for
future reference.
_, CAUTION: Read and follow
all Safety Rules and Operating
Instructions before first use of
this product.
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
983000-136
7-02
• SAFETY
• LOOSE PARTS
• INSTALLATION
• SERVICES
![](/html/08/080a/080a69bd1c38645784bb3cc0c2abefa30608de98040e143d8c924025af54affa/bg2.png)
READ ALL INSTRUCTIONS
READ THESE INSTRUCTIONS AND THE
INSTRUCTIONS FOR THE 212400 COMPOUND
MITER SAW THOROUGHLY before using
accessories.
KNOW YOUR POWER TOOL. Read the operator's
manual for the Compound Miter Saw carefully.
Learn the saw's applications and limitations as well
as the specific potential hazards related to this
tool.
KEEP THE WORK AREA CLEAN. Cluttered work
areas and work benches invite accidents. DO NOT
leave tools or pieces of wood on the saw while it is
in operation.
,a,
The following accessories are included:
• Work Clamp
• Dust Bag
• Table Extensions (2)
• Stop Block
Look for this symbol to point out important safety precautions. It
means attention.V.v, v Your safety is involved.
• ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses; they
are NOT safety glasses.
• ALWAYS DISCONNECT SAW FROM POWER
SUPPLY BEFORE MAKING ADJUSTMENTS OR
ADDING ACCESSORIES. Make sure the switch is
off when reconnecting to power supply.
• SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instruct other users. If you
loan someone this tool, loan them these instruc-
tions also.
• Small Wing Screw
• Clamp Bracket (2)
• Clamp Bracket Screws (2)
• Operator's Manual
?
SMALL
WINGSCREW
STOPBLOCK
DUSTBAG
SCREW
\
CLAMPBRACKET
TABLE EXTENSIONS
Fig. 1
,_ WARNING: The use of attachments or accessories not listed might be hazardous.
![](/html/08/080a/080a69bd1c38645784bb3cc0c2abefa30608de98040e143d8c924025af54affa/bg3.png)
WARNING: To prevent accidental starting that
A
could cause possible serious personal injury,
assemble all parts to your saw completely before
connecting it to power supply. Saw should never
be connected to power supply when you are
assembling parts, making adjustments, installing
or removing blades or accessories, or when not
in use.
DUST BAG
See Figure 2.
The dust bag fits over the exhaust port on the upper
blade guard. To install it, remove the dust guide from
the exhaust port. Then, squeeze the two metal clips to
open the mouth of the bag and slide it on the exhaust
port. Release the clips. The metal ring in the bag
should lock in between the grooves on the exhaust
port. For more efficient operation, empty dust bag
when no more than half full. This will permit better air
flow through the bag.
DUSTBAG
TABLE EXTENSIONS
See Figure 3.
To install table extensions, insert the ends of the
extensions into the holes in the sides of the base.
Secure them in place by positioning a clamp bracket
under each table extension beneath the miter table.
Orient each clamp bracket as shown in figure 3.
Secure each clamp bracket in place with a clamp
bracket screw. The clamp bracket screw threads
through the clamp bracket and tightens against
bottom of miter table, securing clamp bracket against
table extension.
SAWVIEWEDFROM BELOW
5
EXHAUSTPORT
-- CLAMP
6RACKET
TABLEEXTENSION
Fig. 3
Fig. 2