![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bg1.png)
Operator's Manual
Electric
Snow Thrower
®
0®
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
P/N 769-03412 (8/07)
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bg2.png)
THANK YOU
Thank you for buying this quality product. This modern
outdoor power tool will provide many hours of useful
service. You will find it to be a great labor-saving device.
This operator's manual provides you with easy-to-
understand operating instructions. Read the whole
manual and follow all the instructions to keep your new
outdoor power tool in top operating condition.
TABLE OF CONTENTS
Service Information ......................... 2
Rules for Safe Operation ..................... 3
Know Your Unit ............................ 7
Assembly Instructions ....................... 8
Operating Instructions ....................... 9
PRODUCT REFERENCES, ILLUSTRATIONS AND
SPECIFICATIONS
All information, illustrations, and specifications in this
manual are based on the latest product information
available at the time of printing. We reserve the right to
make changes at any time without notice.
Copyright@ 2006 MTD SOUTHWEST INC, All Rights
Reserved.
SERVICE INFORMATION
Service on this unit both within and after the warranty
period should be performed only by an authorized and
approved service dealer.
For service call 1-800-800-7310, or 1-800-668-1238 in
Canada to obtain a list of authorized service dealers near
you. For more details about your unit, visit our website at
www.yardman.com.
If you have difficulty assembling this product or have
any questions regarding the controls, operation or
maintenance of this unit, please call the Customer
Support Department.
Maintenance and Repair Instructions ........... 11
Cleaning and Storage ....................... 12
Troubleshooting Chart ...................... 13
Specifications ............................. 13
Warranty Information ....................... 14
Parts List ............................... $14
Before beginning, locate the unit's model plate. It lists
the model and serial numbers of your unit. Refer to the
sample plate below and copy the information for future
reference.
Model Number
Serial_mber --_ ParentPartNumber
\MODEL: /
S/N : ITEM : /
DO NOT RETURN THE UNIT TO THE RETAILER.
PROOF OF PURCHASE WILL BE REQUIRED FOR
Copy the model and parent
part number here:
WARRANTY SERVICE.
Copy the serial number
here:
Make sure you carefully read and understand this manual before starting or operating this equipment.
THIS PRODUCT IS COVERED BY ONE OR MORE U.S. PATENTS. OTHER PATENTS PENDING.
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bg3.png)
The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
SYMBOL MEANING
,_ SAFETY ALERT: Indicates danger, warning or
caution. Attention is required in order to avoid
serious personal injury. May be used in conjunction
with other symbols or pictographs.
SYMBOL MEANING
I
DANGER: Failure to obey a safety warning will
result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the
risk of fire, electric shock and personal injury.
WARNING: Failure to obey asafety warning can
result in injury to yourself and others. Always follow
the safety precautions to reduce the risk of fire,
electric shock and personal injury.
I
NOTE: Advises you of information or instructions vital to
the operation or maintenance of the equipment.
Read the Operator's Manual and follow all warnings and safety instructions. Failure to do so can result in
serious injury to the operator and/or bystanders.
FOR QUESTIONS, CALL 1-800-800-7310 IN U.S. OR 1-800-668-1238 in CANADA
CAUTION: Failure to obey a safety warning may
result in property damage or personal injury to
yourself or to others. Always follow the safety
precautions to reduce the risk of fire, electric shock
and personal injury.
• IMPORTANT SAFETY INSTRUCTIONS •
READ ALL INSTRUCTIONS
WAI_IIIIIi[IIIIIICI: you must followthe
When using the unit,
safety rules. Please read these instructions
before operating the unit in order to ensure
the safety of the operator and any bystanders.
Please keep these instructions for later use.
Before Operating
• Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
• Do not operate this unit when tired, ill or under the
influence of alcohol, drugs or medication.
• Children under the age of 15 must not use the unit;
teens may operate ttie unit with adult guidance.
• Inspect the unit before use. Replace damaged parts.
Make sure all fasteners are in place and secure.
Replace snow thrower parts that are cracked,
chipped, or damaged in any way.
• Exercise caution to avoid slipping or falling.
Thoroughly inspect the area where the snow thrower is
to be used. Remove all doormats, sleds, boards, wires,
debris, and other foreign objects which may be thrown
by the snow thrower.
Make sure the rotor will spin freely before using the
unit.
Dress properly. Wear adequate winter outer garments.
Wear heavy, long pants, boots, gloves and a long sleeve
shirt. Do not wear loose clothing, jewelry, short pants,
sandals or go barefoot. Secure hairabove shoulder level.
Wear footware that doesn't leak when operating the
snow thrower and that will improve footing on slippery
surfaces. Wear rubber boots.
Never attempt to make adjustments while the motor is
running.
Let the motor and unit adjust to outdoor temperatures
before starting to clear snow.
Always wear safety glasses/shields or goggles at all
times during operation or while performing an
adjustment or repair to protect eyes from foreign
objects that may be thrown from the machine.
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bg4.png)
SAFETY WARNINGS FOR ELECTRIC UNITS
DANGER: When using electric machines, basic
safety precautions should always be followed to reduce
the risk of fire, electric shock and personal injury.
Carefully read and understand the entire operator's
manual before using your unit. Pay close attention to
the operating instructions and safety warnings.
• This snow thrower should be grounded while in use to
protect the operator from electric shock. The snow
thrower is equipped with an approved 3-conductor
cord and 3-prong grounding-type plug to fit the proper
grounding-type receptacle. The green or green/yellow
conductor in the cord is the grounding wire. Never
connect this wire to a live terminal. If your unit is for
use on less than 150 volts, it has a plug that looks like
A in the figure below. If it is for use on 150 to 250
volts, it has a plug that looks like D in the figure.
_ A_ Metal
Gro Screw _Sl_ j
Pin
Grounding Grounding D
Means Pin
• An adapter (show in B and C in the above figure) is
available for connecting 3-prong grounding-type plugs
to 2-prong receptacles. The grounding means
extending from the adapter must be connected to a
permanent ground such as a properly-grounded outlet
box. No adapter is available for the plug shown in D.
• Use only 3-wire outdoor extension cords that have 3-
prong grounding-type plugs and 3-pole receptacles
that accept the snow thrower's plug. Replace or repair
damaged cords.
MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR
120 VOLT APPLIANCES USING 0-12 AMPS
Cord length (ft.) 25 50 100 150
Wire size (AWG) 16 16 14 14
CORD SETS: Please see your dealer for the
appropriated extension cord to use with this product.
Make sure your cord set is in good condition, with a
cord that is heavy enough to carry the current that
your unit will draw. An undersizedcord set will cause a
drop in line voltage resulting in a loss of power, as well
as overheating. The table shown above illustrates the
correct size to use depending on the cord length and
nameplate amperage rating. If in doubt, use the next
heavier size line gauge. The smaller the gauge
number, the heavier the cord. To prevent the cord
from disconnecting from the unit, use the cord hook
shown in the Operating Instructions.
shock, use onlySW-A, SOW-A, STOW-A,SJW-A,
I WARNING: To reduce therisk of electrical I
SJOW-A,SJTW-Aor SJTOW-A cord types.
• Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) that will
be used for the unit. Use receptacles with built-in
GFCI protection for an extra measure of safety.
° A data plate on your unit indicates the voltage used.
Never connect the unit to an AC voltage that differs
from this voltage.
with an extension cord suitable for outdoor use.
I WARNING: To prevent electric shock, use only I
Inspect all extension cords and the unit power
connection periodically. Look closely for deterioration,
cuts or cracks in the insulation. Also inspect the
connections for damage. Repair or replace the cords if
any defects appear.
When cleaning, inspecting or repairing the unit, make
certain the rotor and all moving parts have stopped.
Disconnect the extension cord to prevent accidental
starting.
Do not abuse the extension cord. Never carry the
snow thrower by the cord or yank on the cord to
disconnect it from the receptacle.
Keep the extension cord away from heat, oil, and
sharp edges to prevent damage.
If the extension cord is damaged in any manner while
it is plugged in, pull the extension cord from the wall
receptacle.
Prevent any possible disconnection of the cord
receptacle from the extension cord during operation
by using the cord retainer and guide bar. Refer to the
section Using the Cord Retainer.
Avoid accidental starting. Don't carry a plugged-in
snow thrower with your finger on the switch. Be sure
switch is off when plugging in the unit.
Always unplug the unit and allow it to cool before
putting it into storage. Store indoors.
Always unplug the unit when not in use, and before
performing any maintenance or repairs.
WHILE OPERATING
• Walk, never run.
• Be sure the snow thrower is not in contact with
anything before starting the unit.
• Stay away from the discharge opening at all times.
Keep face, hands, and feet away from concealed
moving or rotating parts.
• Be attentive when using the snow thrower, and stay
alert for holes in the terrain and other hidden hazards
or traffic.
I
I
I
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bg5.png)
° Do not use on a gravel surface or crushed rock
surfaces. Use extreme caution when crossing
gravel/crushed rock drives, walks, or roads.
° Clear snow from slopes by going up and down. Never
go across the slope. Use caution when changing
directions. Never clear snow from steep slopes.
° Never attempt to use the snow thrower on a roof or
any steep, inclined, slippery surfaces.
° Never operate snow thrower without proper guards,
plates or other safety protective devices in place.
° Never operate the snow thrower near glass
enclosures, automobiles, trucks, window wells,
dropoffs, etc. without proper adjustment of the snow
discharge angle. Keep children and pets away.
° Don't force or overload the snow thrower. The snow
thrower will perform at its best and safest when it is
run at the rate for which it was designed.
• Never operate the machine at high speeds on slippery
surfaces. Look behind and use care when backing up.
• Never direct discharge towards people or allow anyone
in front of the unit while operating.
• Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1 standards, and ear/hearing
protection when operating this unit.
• Use the unit only in daylight or good artificial light.
° Avoid accidental starting. Remain in the starting
position whenever starting the unit. The operator and
unit must be in a stable position while starting. See
Starting/Stopping Instructions.
• Use the right tool. Only use this tool for the purpose
intended.
• Do not overreach. Always keep proper footing and
balance.
• Always hold the unit with both hands when operating.
Keep a firm grip on handles or grips.
° Keep hands, face, and feet at a distance from all
moving parts. Do not touch or try to stop the rotor
when it is rotating.
° If the rotor will not rotate freely due to frozen ice, thaw
the unit thoroughly before attempting to operate it
under power.
• Keep the rotor clear of debris.
• Never attempt to clear the rotor with the motor
running. Turn the motor off first and unplug the
extension cord.
• Keep clothing and body parts away from the rotor.
° Do not operate the motor faster than the speed
needed. Do not run the motor at high speed when not
clearing snow.
° Always stop the motor when clearing snow is delayed
or when walking from one location to another.
° Disengage power to the rotor when snow thrower is
transported or not in use.
After striking a foreign object, turn the unit off and
inspect the snow thrower for damage. Unplug the
unit. Repair damage before restarting and operating
the unit.
° If the unit should start to vibrate abnormally, stop the
unit and check immediately for the cause. Vibration is
generally a warning of trouble.
° Stop the motor and unplug the unit whenever you
leave the operating position, before unclogging the
rotor or discharge vanes, and when making any
repairs, adjustments, or inspections.
Never discharge snow onto public roads or near
moving traffic.
Let the snow thrower run for a few minutes after
clearing snow so moving parts do not freeze.
Use only original equipment manufacturer
replacement parts and accessories for this unit. These
are available from your authorized service dealer. Use
of any unauthorized parts or accessories could lead to
serious injury to the user or damage to the unit, and
void your warranty.
Do not use the unit in the hand held position. Do not
pick up the unit when it is powered and running. The
unit is designed to travel along the ground.
OTHER SAFETY WARNINGS
• Be sure to secure the unit while transporting.
• Store the unit in a dry area, locked up or up high to
prevent unauthorized use or damage, out of the reach
of children.
Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use, see Cleaning and Storage
instructions.
If the labels on the unit become defaced or start lifting
off, contact your authorized service dealer.
Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
• Maintain snow throwers with care. Follow instructions
for lubricating and changing accessories.
SAVE THESE INSTRUCTIONS
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bg6.png)
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
• SAFETY ALERT SYMBOL
Indicates danger, warning or caution.
May be used in conjunction with other
symbols or pictographs.
• WARNING - READ
OPERATOR'S MANUAL
Read the operator's manual(s)and follow
all warnings and safety instructions.
Failureto do so can result in serious injury
to the operator and/or bystanders.
• KEEP BYSTANDERS AWAY
WARNING: Keep all bystanders,
especially children and pets, at least
50 feet (15 m) from the operating area.
SYMBOL MEANING
• THROWN OBJECTS AND
ROTATING CUTTER CAN CAUSE
SEVERE INJURY
WARNING: Small objects can be
propelled at high speed, causing
injury. Keep away from the rotating
rotor.
• SPINNING ROTOR CAN CAUSE
SEVERE INJURY
WARNING: Keep hands, feet, and
clothing away from the discharge area.
Do not step in front of the unit, or use
hands to clean the rotor area.
• KEEP HANDS AND FEET AWAY
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bg7.png)
APPLICATIONS
As a snow thrower:
° Clears snow from walkways, driveways, sidewalks,
pathways and more
Starter
Button
Overload
Protection
Switch
Front Handle
Discharge
Directional
Control
/
/
/
/
/
/
/
/
/
/
Cord
Retainer
Bail
Handlebar
\
Cord Guide
Bar
Cord Outlet
Receptacle
Vanes
Rotor
Belt Case Cover
Flange Lock Nut
Handlebar
Knob
Wheels
Cover
Screws (7)
Scraper
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bg8.png)
ASSEMBLING THE HANDLEBARS
Before you can operate the unit, you must install the
handlebars.
1. When you unpack the unit, loosen and remove the
two knobs and washers from the inside of the lower
bars (Fig. 1).
2. Hold the handle bar in the position shown in Figure 1
and slide it onto the lower bars making sure that the
ends of the handlebar are on the inside of the lower
bars.
3. Align the holes in the handlebar with the holes in the
lower bars and insert the bolts through those holes.
4. Check to make sure the bail is assembled into switch
assembly (Fig. 1).
NOTE: Take care not to pinch the switch cable when
positioning the handlebars.
5. Place the washers on the bolts, then screw the two
knobs onto them.
6. Tighten the knobs to secure the handlebars in place.
NOTE: Do not over-tighten the knobs.
7. Clip the switch cable to the cable restraint on the
lower bar as shown in the inset of Figure 1.
8. Remove the banding once the upper handle is
assembled to the lower handle (Fig. 1).
USING THE CORD RETAINER
There is an extension cord retainer to prevent the
extension cord from disconnecting during use. The
retainer hangs from the cord guide bar.
NOTE: Do not plug the extension cord into the power
source receptacle until the cord is connected to
the cord retainer and plugged into the unit.
To use the cord retainer:
.
Fold the extension cord in half, forming a tight loop
near the receptacle.
2.
Push the loop through the bottom hole in the retainer
(Fig. 2).
3.
Slide the loop over the retaining clip and pull down
until the cord fits snugly (Fig. 2).
NOTE: Use a UL-approved extension cord. A 100-foot,
14-gauge cord is recommended. A 50-foot, 16-
gauge cord is acceptable.
Both the cord retainer and guide bar restrain the
extension cord and keep it out of the way at all times,
safely to the side of the operator.
The extension cord and retainer will slide on the guide
bar as the unit is moved to the left and right. Connect
your extension cord to the unit as shown in Figure 3.
Banding
Fig. 1
Fig. 2
Cord Will Slide
Side to Side
Cord
Guide Bar
Fig. 3
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bg9.png)
STARTING INSTRUCTIONS
WARNING: Avoid accidental starting. Make sure
you are in the starting position when using the
snow thrower. To avoid serious injury, the operator
and unit must be in a stable position while starting.
You must follow this sequence correctly to start the unit.
1. Make sure you have plugged in the unit.
2. Press in and hold the red starter button (Fig. 4).
3. While holding the starter button, lift and hold the bail.
NOTE: The unit will NOT start if you fail to press and
hold the starter button until you lift the bail.
4. Hold the bail and begin operating the unit (Fig. 5).
STOPPING INSTRUCTIONS
1. Release your hand from the bail.
2. The starter button will pop out and the unit will stop.
Bail
Starter
Button
/
/
/
/
/
/
/
Overload
Protection
Switch
Fig. 4
Fig. 5
OVERLOAD PROTECTION SWITCH
This unit is equipped with an overload protection switch
to protect the circuit (that the unit is plugged into) from
short circuit overloads.
If the switch pops out:
1. Release the bail and allow the unit to stop and cool
for a minute.
2. Press the overload switch to reset. Resume
operation (Fig. 4).
If the switch pops again shortly after the first time:
1. Allow the unit to cool for 15 to 30 minutes.
2. After the unit has cooled, press the overload switch
to reset. Resume operation.
If the switch does not stay in, or if it continues to pop out
during operation, take the unit to an authorized service
dealer for repair.
OPERATING THE UNIT
1. Start the unit according to the Starting Instructions.
The depth and weight of the snow governs the
forward speed.
2. Push the unit so that it rides on the wheels and
scraper.
3. Make sure the power cord is attached to the cord
retainer and rests on the guide bar. The power cord
should trail to the side of the operator.
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bga.png)
Discharge Direction Adjustment
Snow may be discharged to the left, straight forward, or
to the right of the operator.
To change the direction, use the following instructions:
1. Release the bail to stop the rotor.
2. Firmly grasp the discharge directional control handle
and pull it up. This releases the spring-loaded rod
from the discharge direction slot and allows free
movement (Fig. 6)
3. Turn the discharge directional control to the left, the
center or the right, depending on which direction you
want to throw the snow (Fig. 7).
NOTE: From the center position, the discharge directional
control turns approximately 45 degrees in either
direction (left or right). Do not force it.
4. Release the discharge directional control so it fits
into the slot to secure the desired position.
NOTE: Make sure the discharge directional control is
securely positioned in direction slot and cannot
rotate freely.
5. Restart the unit according to the Starting Instructions.
\
\
Top View
Discharge snow
in FRONT
45°
Discharge snow to
LEFT of operator
45°
,/
Discharge snow to
RIGHT of operator
Fig. 7
Tips for Best Snow Throwing Results
• For the most efficient snow throwing, keep the vanes
parallel and throw snow downwind.
• Slightly overlap each swath you make (Fig. 8).
Directional Control
Pull the Discharge
/_
#
Upwards
/
/
Fig. 6
10
Fig. 8
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bgb.png)
SERVICING THE UNIT
Extreme care and knowledge of the system is required when
servicing this unit. Service should be performed by qualified
service personnel only. Replacement parts for this unit must be
identical to the parts they replace. Refer any repair to an
authorized service dealer.
INSPECTING/REPLACING THE DRIVE BELT
When servicing the unit, use only original equipment
manufacturer replacement parts. Inspect the drive belt once a
year or every 50 hours of operation, whichever comes first, for
wear. If the drive belt needs to be replaced, use the following
instructions.
Belt Tensioner
(Idler Arm)
/
/
/
/
/
/
I_lb WARNING: To avoid serious personal injury,
1,
Remove the flange lock nut from the belt case cover with a
wrench or nut driver (Fig. 9).
2.
Remove the seven (7) screws from the belt case cover
using a #T20 Torx bit or flat blade screwdriver (Fig. 9).
I_ WARNING: To reduce the risk of electrical
Cover
Screws (7)
turn off the unit and allow it to cool. Unplug the
unit before you perform any maintenance.
shock, replace the cover before connecting the
unit to a power source.
I
Driven
Pulley
Fig. 10
5. Reinstall the cover with the seven (7) screws. To make
installation easier, place the narrow part of the cover into
I
the recess of the housing. Install the top two screws, then
push the rest of the cover down into the recess and over
the rotor shaft. Torque all seven (7)screws to 18-23 inolb
(2.0-2.5 Nom).
6. Reinstall the flange lock nut. Torque the nut to
80-100 inolb (9.0-11.2 Nom).
NOTE: If the flange lock nut is damaged, do not replace it with
a standard nut. Replace only with an original
equipment manufacturer replacement part.
Drive Pulley
Belt Tensioner
Belt
Flange Lock Nut
Fig. 9
3. Pull the belt tensioner (idler arm) away from the drive
pulley. Remove the damaged or broken belt from the
driven pulley and drive pulley inside of the housing.
Discard appropriately (Fig. 10).
4. Loop the new belt around the drive pulley and driven
pulley (Fig. 10). Pull the belt tensioner (idler arm) away
from the drive pulley to install the belt around the drive
pulley.
NOTE: Make sure the washer is still in place on the driven
pulley shaft prior to reinstalling the belt case cover.
Drive Belt
Retainer
Driven
Pulley
Fig. 10a
WARNING: When refitting the belt back into the
main housing, be sure that the belt is to the right of
the Drive Belt Retainer. If the belt is placed to the
left, serious damage may occur.
11
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bgc.png)
REPLACING THE SCRAPER CLEANING
I_ ARNING: To avoid serious personal injury,
Use only original equipment manufacturer replacement
parts.
1. Place the unit on the ground or on a work bench.
Position the unit so the vanes and rotor are facing up.
2. Beneath the rotor, locate the three (3) screws securing
the scraper to the housing. Remove them using a
#T20 Torx bit or flat blade screwdriver (Fig. 11).
3. Remove the scraper and discard it appropriately.
4. The new scraper will snap into place. Once in place,
attach it to the unit by reinstalling the three (3)
screws.
Torque the screws to:
always turn your unit off and unplug it before you
perform maintenance.
25-30 in°lb (2.8-3.3 N°m).
I I ARNING: To avoid serious personal injury, I
Use a small brush to clean off the outside of the unit. Do
not use strong detergents. Household cleaners that
contain aromatic oils such as pine and lemon, and
solvents such as kerosene, can damage plastic housing
or handle. Wipe off any moisture with a soft cloth.
TRANSPORTING
• Allow the motor to cool before transporting.
• Secure the unit while transporting.
• To move the unit, grasp it by the top and middle front
handles (Fig. 12).
• If you are transporting the unit with the handles folded,
be careful not to make contact and accidentally bend
the discharge directional control (Fig. 6). If you bend or
damage the control, you can no longer adjust the
vanes.
always turn your unit off and unplug it before you
clean or service it.
Scraper
Fig. 11
STORAGE
° Allow the motor to cool before storing.
• Store the unit locked up to prevent unauthorized use
or damage.
• Store the unit in a dry, well-ventilated area.
• Store the unit out of the reach of children.
12
Fig. 12
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bgd.png)
CAUSE
Unitisunplugged
Starterbuttonorbailwereimproperlyused
Overloadprotectionswitchhaspoppedout
ACTION
Checkcordtomakesureitispluggedintoanelectricaloutlet
Pressinstarterbutton,holdit,andholdbail
PushitinandfollowtheStarting Instructions
CAUSE
Beltisdamaged
CAUSE
Scraperisworn
Replace the belt, according to Inspecting/Replacing the
Driver Belt
Replace the scraper
ACTION
ACTION
If further assistance is required, contact your authorized service dealer
Motor type ............................................................................................................................................................... A.C.,120 Volts Electric
Operating RPM .............................................................................................................................................................. up to 14,000 rpm
Ignition Switch ...................................................................................................................................................... Bail Lock Safety Button
Amperage .................................................................................................................................................................................... 8.5 amps
Overload Protection ................................................................................................................................................. 120V, 15 amp Breaker
Handles .................................................................................................................................................................................... Steel Tube
Approximate Unit Weight ..................................................................................................................................................... 20 Ibs. (9 kg.)
Snow Depth (maximum) ........................................................................................................................................ 6 inches (0.152 meters)
Cleared Path Width ............................................................................................................................................. 12 inches (0.318 meters)
*All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes
at any time without notice.
13
![](/html/51/514a/514aa55c4f67ee1ea99efc2c2f1f0b9cb02fbe9bb8f83f797646599880dc6843/bge.png)
MANUFACTURER'S LIMITED WARRANTY FOR:
®
The limited warranty set forth below is given by MTD
LLC ("MTD") with respect to new merchandise purchased and
used in the United States, its possessions and territories.
MTD warrants this product against defects in material and
workmanship for a period of two (2) years commencing on the
date of original purchase and will, at its option, repair or
replace, free of charge, any part found to be defective in
material or workmanship. This limited warranty shall only apply
if this product has been operated and maintained in
accordance with the Operator's Manual furnished with the
product, and has not been subject to misuse, abuse,
commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water or damage because of
other peril or natural disaster. Damage resulting from the
installation or use of any accessory or attachment not
approved by MTD for use with the product(s) covered by this
manual will void your warranty as to any resulting damage. This
warranty is limited to ninety (90) days from the date of original
retail purchase for any MTD product that is used for rental or
commercial purposes, or any other income-producing purpose.
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE THROUGH YOUR LOCAL
AUTHORIZED SERVICE DEALER. To locate the dealer in your
area, please check for a listing in the Yellow Pages or contact
the Customer Service Department of MTD LLC by calling
1-800-800-7310 or writing to P.O. Box 361131, Cleveland
OH 44136-0019 or if in Canada call 1-800-668-1238. Or visit
our website at www.yardman.com. No product returned
directly to the factory will be accepted unless prior written
permission has been extended by the Customer Service
Department of MTD LLC.
This limited warranty does not provide coverage in the
following cases:
A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters.
B. Wear items - Bump Knobs, Outer Spools, Cutting Line,
Inner Reels, Starter Pulley, Starter Ropes, Drive Belts.
No implied warranty, including any implied warranty of
merchantability or fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty or guaranty, whether written or oral,
except as mentioned above, given by any person or
entity, including a dealer or retailer, with respect to any
product shall bind MTD. During the period of the
Warranty, the exclusive remedy is repair or replacement
of the product as set forth above. (Some states do not
allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.)
The provisions as set forth in this Warranty provide the
sole and exclusive remedy arising from the sales. MTD
shall not be liable for incidental or consequential loss or
damages including, without limitation, expenses incurred
for substitute or replacement lawn care services, for
transportation or for related expenses, or for rental
expenses to temporarily replace a warranted product.
(Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.)
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of the safety features of the product shall void this Warranty.
You assume the risk and liability for loss, damage, or injury
to you and your property and/or to others and their property
arising out of the use or misuse or inability to use the
product.
This limited warranty shall not extend to anyone other than
the original purchaser, original lessee or the person for whom
it was purchased as a gift.
How State Law Relates to this Warranty: This warranty
gives you specific legal rights, and you may also have other
rights which vary from state to state.
To locate your nearest service dealer dial 1-800-800-7310
in the United States or 1-800-668-1238 in Canada.
C. MTD does not extend any warranty for products sold or
exported outside of the United States of America, its
possessions and territories, except those sold through
MTD's authorized channels of export distribution.
MTD reserves the right to change or improve the design of
any MTD Product without assuming any obligation to modify
any product previously manufactured.
14
MTD LLC
P.O. Box 361131
Cleveland, OH 44136-0019