Craftsman 211420 Assembly Instructions And Parts List

Grinq :t

21142q

SAVE THESE ASSEMBLY iNSTRUCTiONS AND PARTS LiST

ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL
ff this Craftsman tool fails due to a defect in material or

workmanship within one year from the date of purchase,
CALL 1-800-4-MY-HOME e_TO ARRANGE FOR FREE

REPAIR.
This warranty applies onIy while this tool is in the United

States.
This warranty gives you specific Iegal rights, and you may

aIso have other rights, which vary from state to state.
Sears, Roebuck and Co°, Dept° 817WA

Hoffrnan Estates, _L60179

®

6, KEEP VISITORS AND CHILDREN AWAY. DO NOT

permit people to be in the immediate work area,
especially when the electrical tool is operating,

7, DO NOT FORCE THE TOOL to perform an opera-

tion for which it was not designed, it wiil do a safer
and higher quality job by only performing opera-

tions for which the tool was intended,

8, WEAR PROPER CLOTHING. DO NOT wear loose

clothing, gloves, neckties, or jewelry, These items
can get caught in the machine during operations
and puil the operator into the moving parts, The

user must wear a protective cover on their hair, if
the hair is long, to prevent it from contacting any

moving parts,

GENERAL SAFETY iNSTRUCTiONS
FOR POWER TOOL

Before using the Bench Grinder Leg Set, read and
understand the instruction Manual,

To avoid serious injury and damage to the tool, read
and follow all of the Safety and Operating instructions

before operating the Power Tool,

1, READ the entire instruction Manual, LEARN how to

use the tool for its intended applications,

2, GROUND ALL TOOLS, if the tool is supplied with a

3-prong plug, it must be plugged into a 3-contact
electrical receptacle, The 3rd prong is used to
ground the tool and provide protection against

accidental electric shock, DO NOT remove the
3rd prong,

3, AVOID A DANGEROUS WORKING ENVIRON-

MENT. DO NOT use ebctdcal tools in a damp
environment or expose them to rain,

4, DO NOT use electrical tools in the presence of

flammable liquids or gasses,

5, ALWAYS keep the work area dean, well lit, and

organized, DO NOT work in an environment with
floor surfaces that are slippery from debris, grease,

and wax,

9, ALWAYS WEAR EYE PROTECTION, Any power

tool can throw debris into the eyes during opera-
tions, which could cause severe and permanent

eye damage, ALWAYS wear Safety Goggbs (that
comply with ANSI standard Z87,1) when operating
power tools, Safety Goggles are available at Sears

Retail Stores,

10,

WEAR A DUST MASK TO PREVENT INHALING

DANGEROUS DUST OR PARTICLES,

11,

ALWAYS UNPLUG THE TOOL FROM THE ELEC-

TRICAL RECEPTACLE when making adjustments,
changing parts or performing any maintenance,

12,

KEEP PROTECTIVE GUARDS IN PLACE AND IN

WORKING ORDER,

13,

AVOID ACCIDENTAL STARTING, Make sure

that the power switch is in the "OFF" position
before plugging in the power cord to the electrical

receptacle,

14,

REMOVE ALL MAINTENANCE TOOLS from the

immediate area prior to turning "ON" the Bench
Grinder,

15,

USE ONLY RECOMMENDED ACCESSORIES,

Use of incorrect or improper accessories could
cause serious injury to the operator and cause
damage to the tool, if in doubt, check the instruc-
tion manual that comes with that particular acces-
sory,

16,NEVERLEAVE A RUNNING TOOL UNATTENDED,

Turn the power switch to the "OFF" position, DO
NOT leave the tool until it has come to a complete

stop,

17, DO NOT STAND ON A TOOL, Serious injury

could result if the tool tips over or you accidentally
contact the took

18, DO NOT store anything above or near the tool where

anyone might try to stand on the tool to reach it,

19, MAINTAIN YOUR BALANCE. DO NOT extend

yourself over the tool, Wear oil resistant rubber°
soled shoes, Keep floor clear of debris, grease,
and wax,

20, MAINTAIN TOOLS WITH CARE, Always keep tools

clean and in good working order, Keep all blades
and tool bits sharp,

21, EACH AND EVERY TIME, CHECK FOR DAM-

AGED PARTS PRIOR TO USING THE TOOL,
Carefully check all guards to see that they operate

properly, are not damaged, and perform their
intended functions, Check for alignment, binding or
breaking of moving parts, A guard or other part that
is damaged should be immediately repaired

or replaced,

22, CHILDPROOF THE WORKSHOP AREA by

removing switch keys, unplugging tools from the
electrical receptacles, and using padlocks,

23, DO NOT OPERATE TOOL IF UNDER THE

INFLUENCE OF DRUGS OR ALCOHOL,

24, SECURE ALL WORK, When it is possible, use

clamps or jigs to secure the workpiece, This is
safer than attempting to hold the workpiece with

your hands,

SAVE THESE iNSTRUCTiONS.

UNPACKUNG AND CHECKUNG CONTENTS

This Bench Grinder Leg Set wiii require a minimal
amount of assembly, Use a rubber mallet or a hammer
with a wooden block for assembly,

Remove all of the parts from the shipping box,
Check and clean each part and lay them on a clean
work surface, Compare the items and quantities to
Figure 1-1,

CAUTION: if there is any missing or damaged parts,
do not attempt to assemble this Bench Grinder Leg Set,
To obtain missing or damaged parts, please call

1°800°897°7709,

Figure 1-1

\

\

KEY PART
NO, NO, DESCRmPTION

1 OR93517 TRAY

2 STD52320 HEX HD SCR 5/16-18 X 2" (not shown)
3 STD551031 FLAT WASHER 5/16" (not shown)
4 STD551131 LOCK WASHER 5/16" (not shown)
5 STD541031 HEX NUT 5/16-18 (not shown)

6 OR93518 UPPER LEG
7 OR93519 LOWER LEG
8 OR93520 SHORT HORIZONTAL SUPPORT
9 OR93521 LONG HORIZONTAL SUPPORT

10 OR90394 FOOT

O:0

QTY, 1

2
4

2 7
2

4
4
2
2
4

DO NOT ASSEMBLE the Bench Grinder Leg Set until
you have read and understand the entire instruction

Manual,
DO NOT ASSEMBLE the Bench Grinder Leg Set if

any parts are missing or damaged,

LEG SET ASSEMBLY

Figure 2-1

0

o

Figure 2-3

2, Repeat Step 1 on the remaining Upper Legs,
3, insert the 2 tabs on the end of the Lower Leg (7)

into the 2 slots in the end of the Upper Legs (refer
to Figure 2ol), Using a rubber mallet or a hammer

with a wooden block, tap the Lower leg until the
tabs are fully engaged into the Upper Leg,

insert the 2 tabs on the end of the Upper Leg (6)
into the 2 shots in the Tray (1), See Figure 2ol,
Using a rubber mallet or a hammer with a wooden
Mock (Figure 2°2), tap the Upper ieg until the tabs
are fuliy engaged into the Tray, See Figure 2°3,

Figure 2-2

4, Repeat Step 3 on the remaining Lower Legs,

Figure 2-4

5,

insert the 4 square hobs on the Long Honzontal
Support (9) over the ears on the Lower Leg (see
Figure 2°4), Using a rubber mallet or a hammer
with a wooden Mock, tap the HonzontaH Support
downward until the square hobs bottom out on
the ears on the iower iegs,

6,

Repeat Step 5 on the Short HonzontaH Support (8)
See Figure 1ol,

7,

Assemble the plastic Foot (10) onto the end of each
Leg, See Figure 1ol,

3