Craftsman 139.53778 Owner's Manual

i Aodel 139.53778
3-Fu nction Transmitter

Owners Manual

F+CC+rules prohibit adjustments to or modification of receiver andlor transmitter circuitry except for changing the code setting
and replacing transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS_

Manufactured under I or mors of th_ lot[owingUS palents: RE29,525; 4,037,201;4,750jt8; 4.806,930

MATCH THE CODE IN NEW AND EXISTING TRANSMITTERS

If this transmitter will be used wlth an existing transmitter to ope_te the same receiver(a), proceed as follows:
Locate the code switches in original transmitter(s), Open the battery compartment cover in the new 3-function transmitter
to access the code _witches, Place the transmitters side by side as shown below.+

Set code switches in the new transmitter to the same positions as code switches in the odglnal transmitter(s),
NOTE 1: Code switches #2 through #9 In ALL transmitters used to operate a receiver must be set to match. (Code

switch #1 on a 3-function transmitter is neutral, Set it to ANY position. It will not affect the code selected.
NOTE 2: If the original transmitter(s) has only 7 or 8 code switches, set code switches #8 and/or #9 to center

(0) position in new transmitter,

3-Fur_l_on

Transmitler

Cede Switches

(_._)

C:3 C:_ H J 3-Funclion

_ Transmitte,"

i_--"_1_""_ + tl CodeSwitches

O "

3-Func_n

Mini Transrnirier

Code Switches

(_-9)

REPLACEMENT PARTS: Case, top and bottom (No circuit board) - 41A3476; Visor clip - 290128; 12V Battery. 10A14

CHANGE THE CODE IN RECEIVER AND TRANSMITTER(S)

530OOSR SERIES

0NITH REC-EIVER 'SR' CODE B_N)

Garage Door Openers and Light Controls

(ltlustration A shows e garage door opener receiver)

SeJec[atransmlt_er

==

push buttc_ to _,_

operatereceiver

PUsh Butlons

Cede Bu_on u_

Makesure all transmittersareset tomatching code switch

positions as described above.

1+Press the 'SR' code button on your receiver+(illustra-

tion (A) shows a representative garage door opener
receiver). The indicator light will turn ON,

2, STANDAWAYFROM DOORar_ press theSELECTED

PUSH BUTTON of one transmitter.The indicator light
will turn OFF and door will move.Code In receivernow

matches transmitter(s) code andwill activatewhen the
selected transmitter push button is pressed,

NOTE." If transmitter push button le not pressed

within 30 seconds, the lndic.slor light will turn OFF,

Repeat 1 and 2.

Touse the 3-Function Transmitterwithother 53000 SR
Series receivers: Select anothertransmitter pushbutton

tooperatea UghtControloradditbnal garagedooropener.

All transmitters used tooperate receivermt_'t besetto the
same code (as described abo_e).Then repeat t and 2.
Youcan select a different transmitter push button to oper-

ate each device.

114Al154B

53000 SERIES

(WITH RECEIVER CODE SWITCHES)

Garage Door Openers and Light Controls

(Illustration B shows n garage door opener receiver)

PushButlon(-)_

PushButton(0)

PushBunon(+)

B

t%%% []

l

Code switch #1 in (-) pos'll_on, Receiver w_lt

operate wibh transmitters' large push bullon

Select a
Iransmit[er
push but_c,n

to operate
receiver

Slide receiver

code switch # I

to posldon b"_t
matches selected
Iransmiller

push button

Make sure 811transmitters are set tomalching code switch
positions as described above.

I. Select a transmitter push button to operate the receiver

as shown in Figure B,

2. Set RECEIVER code switch #1 to match the position
of the transmitter push button selected. Refer to
Illustration (B). Then set remaining code switches in
receiver to match the transmitter(s) code switch positions.

NOTE: if the receiver has only 7 or 8 switches, set
transmitter swttch #8 and/or #9 to (0)o

To use the 3-Function Transmitter with other 53000
Series receivers: Set receiver code swilch #1 to match

the position of another transmitter push button+ Then set

remaining code switches to match transmitter(s) code

switches+

Code switches #2 through #9 in all transmitters used

to operate the receiver MUST be set to matching
positions.

i ii ii ii i H ml ii i Hii ilmlll.,. ,ll.ll.llHll

@ 1990_Sears Roebuck & Company

All Rights Reserved Printed In Mexk:o

Sears Model 139.53778
3-Function Transmitter

REPLACEMENT PARTS:
Case, top and bottom (No circuit board)

Visor clip

12V Battery

41A3476

29C128

10A14