Craftsman 139.53682 User Manual

CRRFTSMRN ®

OWNER'S MANUAL

SECURITY,F

Universal Remote Control

Conversion Kit

Model 139.53682 (With I Remote Control)

Model 139.53683 (With 2 Remote Controls)

Children operating or playing with s garage door

opener can injure themselves or others. The

garage door could close and cause serious injury or death.

Install the receiver (or any additional push buttons) out of the reach of children and away

from all moving parts of the door and door

hardware, but where the garage door is visible. Do not allow children to operate the push button(s) or the remote control(s).

A moving garage door could injure someone under it. Activate the opener only when the door

is properly adjusted, you can see it clearly, and

there are no obstructions to door travel•

DISCONNECT POWER TO THE GARAGE DOOR OPENER REFOREPROCEEDING.

The SECURITY+ Universal Remote Control

Conversion Kit consistsof a receiver and remote control(s). This accessorywill convert almost any garage

door opener to rollingcode technology. The remotecontrol sends a coded signalfrom outside the garage. Insidethe

garage, the plug-inreceiver accepts the transmittedsignal

and starts the dooropener. With Security+, the code between the remote control and the receiver changes with

each use, accessing over 100 billion new codes. IMPORTANT: To improve the security of your opener,

discard your old remote controls end erase or reset your code. For maximum security and range, you

must disable the existing receiver on your opener, otherwise it could still activate your opener:

• Ifthere is an external receiver, disconnect power to it.

• If it is an integrated receiver, either clip off the component that feeds power to the receiver or

remove the tuning slug and antenna from the receiver section. If you have a different brand of opener,

contact the manufacturer for additional information on

disabling the existing receiver.

• If you have a Sears opener with an SRT receiver,

erase the old codes by holding down the SRT button

for 6 seconds until the indicator light turns off.

• If you have code switches, reset them to a random

code and deactivate the receiver as follows: On the opener panel, peel

back the lower right _ I_ I_ corner of the label to

expose the tuning

Cut Antenna

slug (closest tothe antenna), as shown.

Remove the slug with a small hex

head wrench and cut

Tuning

-- Slug

.Peal beck label

at comet

the antenna wire.

To complywithFco rules,adjustmentsor modificationsof thr= reseivorand,/or transmitterare prohibited,except forchangingthe code set_g o_replacing

the ransmittorbattery.THEREARE NO USERSERV CEABLEPARTS.

NOTICE TO U. S. CONSUMERS:

Some stat_sprohibitthe service or repairof garage door openers wbchcannotbe madeto complywiththe safetystandardscontained in UL325 (1988 revision).In ordertocomplywithboththeletterand the spiritof these laws, this universalremote conttolconverterkit shouldnotbe used with anySears Craftsman=garage dooropener

manufacturedpdorto Apdl1, 1982.

Aotuator Cover Indicator

Light

Power..

SRT ._

Indicator

Antenna

"o _11 Wire

ght

- Illico..- _ act Bell Wire

•"_-- Opener Terminals

SRT (learn)

Actuator Belllwira

!Terminals

L._ to Garage Door

OPEN RECEIVER: Insert a small screwdriver in slot on receiver front panel as shown• Twist up actuator cover.

CONNECT RECEIVER AND OPENER: Remove about

1/4" of insulation from each end of the 2-strand bell wire.

Connect one end to the receiver screw terminals

(polarity is NOT required). Route wire along the

channels and out the bottom as shown. Connect the other end of the bell wire to the two opener

terminal screws labeled "2" (white) and "1" (red), "common" and "command" or the terminals used for the

push button control.

Use insulated staples (not supplied) to secure bell wire between receiver and opener. Length of bell wire

depends on where the receiver will be installed. Replace the actuator cover.

Choose a 120Vac polarized outlet for the receiver which is OUT OF THE REACH OF CHILDREN. Plug receiver

into selected outlet. Return power to the opener.

Side two contains code setting instructions and service information,

PROGRAMMING THE RECEIVER The receiver and remote control(s) have been

factory preset with a matching code. The door will open when you press the LARGE push button. You can activate your opener with up to eight SECURITY.I. remote controls (with blue push buttons) and one SECURITY+ Keylees Entry.

Ifyou purchase additional remote controlsto operate this receiver:

1. Remove the receiver actuator cover.

2. Press and HOLD the selected remote controlpush button (Illustration A).

3. Then press the SRT (learn) actuator on the receiver (Illustration B). The adjacent indicatorlight will FLASH. Release the remote control push button.

The opener will now operate when either the receiver actuator or the remote control push button is pressed.

3-Function

Remote Control

Select a remote control push

button to operate receiver

UnlversalReceiver

B o

SRT

Actuator

(loam)

Light

NOTE: If the remote control push button is not held down until the receiver Indicator light flashes, the

receiver will not learn the code.

To erase ALL remote control codes from memory:

Press and HOLD receiver SRT actuator. Indicator light alongside will glow. When the Indicator light

turns OFF (in about 6 seconds) ALL codes will be

erased.

REPLACEMENT PARTS

Universal Receiver (complete) .................... 41.6,5041-1

Receiver Actuator Cover .......................... 41A4926

Remote Control Housing Only (no circuit board) ....... 41A5032

Visor clip ...................................... 29B134

3V 2032 Lithium Battery ............................ 10A20

(1 required for Remote Model 139.53681B)

3V 2016 Lithium Battery ............................ 10A19

(2 required for Remote Model 139.53681)

THE REMOTE CONTROL BATTERIES

Openthisend firsttoavoid/_L--'_"_

cracking_sf_._-_<:_._--,"/

housin_

_:_ • Twist

toopen

The lithium batteries should

produce power for up to 5 years. Replace batteries positive side

down, as follows: Use the visor clip or screwdriver blade to pry open the case as shown. To

replace the cover,insert the 3 tabs at the opposite end and snap shut.

When ordering parts, always provide the following

information:

• Product Type

• Model Number

• Part Number

• Part Description

For the repair or replacement parts you need

Call 7 am - 7 pm, 7 days s week

1-800-366-PART

(1-800-366-7278)