Craftsman 139.30498, 139.30499 Owner's Manual
For use with Craftsman 315 MHz or 390 MHz garage door openers manufactured after
January 1, 1993. The garage door opener activates when the programmed button on the
remote control is pressed. The remote control can activate up to three garage door openers.
Make sure the garage door opener has a working light bulb because it is a programming
indicator.
MODEL 139.30498
LED
MODEL 139.30499
LED
PREPARE
3-BUTTON REMOTE CONTROLS
MODELS 139.30498 AND 139.30499
To prevent possible SERIOUS INJURY or
DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of
reach of children. NEVER permit children
to operate or play with remote controls.
• Activate gate or door ONLY when it can be
seen clearly, is properly adjusted and there
are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight
until completely closed. NEVER permit
anyone to cross path of moving gate or
door.
Learn
LED
Green
or
Red/Orange
OR OR
Purple
PROGRAM THE REMOTE CONTROL (139.30498)
1
To enter
programming
mode, use the
visor clip to
press the Program
button until the LED
on the front of the
remote control turns on.
2
Press and
release the
Learn button
on the garage
door opener.
The Learn LED will light.
Within 30 seconds...
Learn
LED
Locate the Learn
button on the garage
door opener.
NOTE: Your garage door
opener may look different.
Learn
LED
Yellow
3
Press and release the remote
control button you want to use...
Check to see if the garage door opener
light bulb blinks. If not, wait for the
remote control LED to light solid then
slowly press and release the remote
control button again. Repeat until the
light bulb blinks.
DO NOT press the button after the
light bulb blinks.
Locate the Program button on the
remote control.
Program Button
139.30498
139.30499
Program Button
4
To exit programming mode, press
any remote control button except
the button that was just programmed.
5
To test, press the programmed button on
the remote control...
The garage door opener
will activate.
6
Install the visor clip.
PROGRAM THE REMOTE CONTROL (139.30499)
1
Using a safety pin or paper
clip, press the Program button
until the LED on the front of
the remote control turns on.
4
To exit programming mode, press
any remote control button except
the button that was just programmed.
2
Press and
release the
Learn button
on the garage
door opener.
3
Press and release the remote
control button you want to use...
Check to see if the garage door opener
light bulb blinks. If not, wait for the
remote control LED to light solid then
slowly press and release the remote
The Learn LED will light.
control button again. Repeat until the
light bulb blinks.
DO NOT press the button after the
light bulb blinks.
Within 30 seconds...
5
To test, press the programmed button on the remote control...
The garage door opener
will activate.
BATTERY
The LED on your remote will stop flashing when the battery is low and needs to be replaced.
To replace battery, open the case as shown. Insert battery positive side up (+). Replace the battery
with only 3V2032 coin cell batteries. Dispose of old battery properly.
139.30498
Pry open the case first in the middle (1), then
Pry open the case with a screwdriver blade.
139.30499
at each side (2 and 3) with the visor clip.
2
1
3
REPLACEMENT PARTS
To prevent possible SERIOUS INJURY or
DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify
doctor.
To reduce risk of fire, explosion or chemical
burn:
• Replace ONLY with 3V2032 coin batteries.
• DO NOT recharge, disassemble, heat
above 212° F (100° C) or incinerate.
NOTICE: To comply with FCC and or Industry Canada rules (IC),
adjustment or modifications of this receiver and/or transmitter
are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.
Tested to Comply with FCC Standards for Home or office use.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20
Visor Clip
(Model 139.30498 ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B137
To order replacement parts call...
®
1-800-4-MY-HOME
(1-800-469-4663)
Loading...