Craftsman 139.21242 Owner's Manual

ICRRFTSMRN°I

Garage Door Monitor

Model 139.21242

To prevent possible SERIOUSINJURYor DEATHfrom a closing garagedoor:

• NEVERpermit children to operate or play with door control push buttons or remote
control transmitters.

• Activate door ONLYwhen it is properly adjusted and there are no obstructions to
door travel.

• This door monitor works with an operator system equipped with an unattended
operationfeature. The door could move unexpectedly.NO ONESHOULDCROSS

THE PATHOFTHEMOVING DOOR.

NOTICE:To comply with FCCand/or Industry Canada(IC) rules, adjustment or modifications of this transceiver are
prohibited.THEREARENOUSERSERVICEABLEPARTS.

Thisdevicecomplieswith Part15of the FCCrulesand IC RSS-210,Operationissubject tothe following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,including

nterferencethat maycauseundesred operaton,

Introduction

Thegarage door monitor indicates the status of your garagedoor from inside the home.
Thegarage door monitor can be programmed with upto four garage door openers. The
garagedoor monitor is compatible with AssureLinkTM enabledgaragedoor openers only.

GARAGEDOORMONITOR Adapter 9 Vdc

Volume Control Button

)eaker Port

LEDs

Close Door Button

Features

VOLUMECONTROLBUTTON

TheVolume Control button allows you to set the volume to low, medium, high, or off.

CLOSEDOORBUTTON

TheClose Door button will close all open doors. Both LEDs will blink simultaneously as
the doors are closing. A long beepwill be heardconfirming the doors are closed.

Features (Continued)

LEDINDICATORS

LEDS MEANING

Red Green

Blinking Off At least one garage door is open
Off Solid ALL doors are closed

Solid Off No signal has beenreceived from a programmed garage

door openerwithin the last 20 minutes (implies a power
outageor a garagedoor opener malfunction)

Solid Solid Thegarage door monitor has been successfully

programmed

Redandgreen LEDsblink Thegarage door(s) is closing after pressing the CloseDoor
simultaneously button

Redandgreen LEDsblink Thegarage door monitor is not programmed to any garage

alternately and slow door opener

Redandgreen LEDsblink Thegarage door monitor is in programming mode

alternately fast

Off Off No powerto the garagedoor monitor

AUDIBLEALERT

Audible tones alertyou of the garage door(s) status. TheVolume Control button allows

_outo setthe volume to low medium, high, or off.

AUDIBLETONES MEANING

Oneshort beep* • Initiated Programming

• Initiated EraseMemory

• Memory has beenerased

• CloseDoor button has beenpressed

Two short beeps* Thegarage door monitor has been

successfully programmed
Failedattempt to program fifth garage door opener
Agarage door(s) is opening

Agarage door(s) is open
No communication with the garagedoor opener

Door closes successfully after pressing CloseDoor button

* These beepswill not be heard if the volume is setto OFF.

Two long beeps*
Three short beeps*

Oneshort beep repeating*
Onelong beep repeating*

Onelong beep*

Setup

Connectthe adapter to the garage door
monitor and a standard 110 Vac outlet.

NOTE:Depending on theplanned location

of the monitor within the home, it may be

more convenient to temporarily place the
monitor near the GarageDoor Opener

during programming. Onceprogramming
is completeplace the monitor in the
desired location.

Programming

1. Press and releasethe Learn button on
the back of the garagedoor monitor.

Within 60 seconds, press and release
the Learn button on the garagedoor
opener. Two short beepswill confirm
the garagedoor monitor has been
successfully programmed.

NOTE:Toprogram additional garagedoor

openers, repeat the steps above on each

individual garagedoor opener. Thegarage
door monitor can be programmed with up

to four garage door openers.

ERASEMEMORY

To eraseall programmed garagedoor openers from the garage door monitor, press and
hold the Learn button on the garage door monitor for at least six seconds. One short beep
will be heard at the beginning, one short beepwill confirm that all codes have been

erased.