Craftsman 139.18802, 139.18803 User Manual

For use with Craftsman 315 MHz or 390 MHz garage door openers manufactured after
January 1, 1993. The garage door opener activates when the programmed button on the
remote control is pressed. The remote control can activate up to three garage door openers.

Make sure the garage door opener has a working light bulb because it is a programming
indicator.

MODEL 139.18802

LED

MODEL 139.18803

LED

PREPARE

3-BUTTON REMOTE CONTROLS

MODELS 139.18802 AND 139.18803

To prevent possible SERIOUS INJURY or
DEATH from a moving gate or garage door:

• ALWAYS keep remote controls out of
reach of children. NEVER permit children
to operate or play with remote controls.

• Activate gate or door ONLY when it can be
seen clearly, is properly adjusted and there
are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight
until completely closed. NEVER permit
anyone to cross path of moving gate or
door.

Learn
LED

OR OR

Green
or
Red/Orange

Purple

PROGRAM THE REMOTE CONTROL (139.18802)

1

Press and hold the program button
the remote control until the LED on
the front of the remote control
turns on.

2

Press and release the remote control button you wish to use the
number of times that corresponds with the garage door opener type:

# of Presses Garage Door Opener Type

1
2
3
4

Locate the Learn
button on the garage
door opener.

NOTE: Your garage door
opener may look different.

Learn
LED

Learn
LED

Yellow

Security+ 2.0
315 MHz Security+
390 MHz Security+
390 MHz Billion Code (Green Learn Button)

TM

(Yellow Learn Button)

®

(Purple Learn Button)

®

(Red/Orange Learn Button)

Locate the Program button on the
remote control.

Program Button

139.18802

Program Button

3

To exit programming mode,
press any remote control
button except the button
that was just programmed.

139.18803

4

Press and release the Learn
button on the garage door
opener.

The Learn LED will light.

Within 30 seconds...

Learn
Button

56

Press the remote control button
programmed in step 2 until the

To test, press the programmed
button on the remote control...

7

Install the visor clip.

garage door opener lights flash
or two clicks are heard.

Click

Click

The garage door
opener will activate.

PROGRAM THE REMOTE CONTROL (139.18803)

1

Press and hold the program button
the remote control until the LED on
the front of the remote control
turns on.

Safety pin or
paper clip

4

Press and release the Learn
button on the garage door
opener.

Learn
Button

The Learn LED will light.

Within 30 seconds...

2

Press and release the remote control button you wish to use the
number of times that corresponds with the garage door opener type:

# of Presses Garage Door Opener Type

1
2
3
4

56

Press the remote control button

Security+ 2.0
315 MHz Security+
390 MHz Security+
390 MHz Billion Code (Green Learn Button)

TM

(Yellow Learn Button)

®

(Purple Learn Button)

®

(Red/Orange Learn Button)

To test, press the programmed button on the remote control...

3

To exit programming mode,
press any remote control
button except the button
that was just programmed.

programmed in step 2 until the
garage door opener lights flash
or two clicks are heard.

Click

Click

The garage door
opener will activate.

BATTERY

The LED on your remote will stop flashing when the battery is low and needs to be replaced.
To replace battery, open the case as shown. Insert battery positive side up (+). Replace the battery
with only 3V CR2032 coin cell batteries. Dispose of old battery properly.

139.18802

Pry open the case first in the middle (1), then

Pry open the case with a screwdriver blade.

139.18803

at each side (2 and 3) with the visor clip.

2

1

3

REPLACEMENT PARTS

To prevent possible SERIOUS INJURY or
DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify
doctor.

To reduce risk of fire, explosion or chemical
burn:

• Replace ONLY with 3V CR2032 coin
batteries.

• DO NOT recharge, disassemble, heat
above 212° F (100° C) or incinerate.

NOTICE: To comply with FCC and or Industry Canada rules (IC),
adjustment or modifications of this receiver and/or transmitter
are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.

Tested to Comply with FCC Standards for Home or office use.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20

Visor Clip

(Model 139.18802 ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B137

To order replacement parts call...

®

1-800-4-MY-HOME

(1-800-469-4663)