Craftsman 139.18795 Owner's Instructions Manual

INSTALLATION

1. Choose a convenient
location for installation.
Install out of the reach
of children at a
minimum height of 5
feet (1.5m), away from
all moving parts of
door.

For a one-piece door,
choose the optional
location shown in the
illustration to avoid injury as the door swings up and out.

Test the reception of the Keyless Entry by operating your
opener from the selected location. Change the location if
necessary.

2. Remove the compartment cover to access the bottom
mounting hole. Slide the cover down to remove. Remove
battery.

3. Center the keypad at eye level
against the selected location. Mark
4-1/4" (10.8 cm) up the centerline
from the bottom and drill a 1/8" (3.2
mm) pilot hole. Install top mounting
screw, allowing 1/8" (3.2 mm) to
protrude above surface. Position
keypad on screw head and adjust
for snug fit.

With cover open so bottom
mounting hole is visible, mark the
position of the hole. Remove
keypad and drill 1/8" (3.2 mm) pilot hole. Replace keypad and
complete installation with bottom screw, using care to avoid
cracking plastic housing. Do not over tighten.

Reinstall battery and replace the battery cover. To replace
battery cover slide up and snap it into place.

1

Security✚

®

Keyless Entry

Model 139.18795

OWNER'S INSTRUCTIONS

Door Jamb Edge
(Optional)

Keyless
Entry

Door Jamb Face
(SECTIONAL DOOR ONLY)

KEYLESS ENTRY MUST BE
INSTALLED WITHIN
SIGHT OF THE DOOR

Exterior Front Wall
1-Piece or
Sectional Door

Typical
Installation

Side two contains instructions for changing the personal
entry password and setting a temporary password.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.

1. Press and release the “learn” button on motor
unit. The learn indicator light will glow
steadily for 30 seconds.

2. Within 30 seconds, enter a four digit personal
identification number (PIN) of your choice on
the keypad. Then press and hold the ENTER
button.

3. Release the button when the motor unit lights
blink. It has learned the code. If light bulbs are
not installed, two clicks will be heard.

SETTING THE PERSONAL ENTRY PASSWORD

We recommend that you program your password now, before
you install the Keyless Entry. Then you can test the reception
at the mounting location before you proceed further.

USING THE “LEARN” BUTTON

FEATURES

For use with any Security✚®garage door openers having an
orange "learn" button.

Personalized Password: Up to 10,000 possible
combinations. Password can be easily changed if desired.

Temporary Password: Can be added for visitors or service
persons. This temporary password can be limited to a
programmable number of hours or a programmable number
of entries.

Rolling Code: While your password remains constant until
you change it, the code between the Keyless Entry and the
receiver changes with each use, randomly accessing over
100 billion new codes.

Operation: Opener activates when 4-digit password and
Enter button is pressed.

If wrong numbers are accidentally pressed, correction can be
made immediately. The Enter button will transmit only the last
four digits.

The Keypad will blink for 15 seconds after the password is
transmitted. During that time the Enter button can be used to
stop or reverse the door travel.

To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:

• Install door control within sight of gate or garage door, out of
reach of children at a minimum height of 5 feet (1.5 m), and away
from all moving parts of gate or door.

• NEVER permit children to operate or play with gate or door control
push buttons or remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate or
closing garage door.

WARNING





WARNING

Keypad Cover

31D431

Bottom mounting

hole

Battery

10A2

Battery

Cover

31B430

114A2152B

TO CHANGE AN EXISTING, KNOWN PIN

If the existing PIN is known, it may be changed by one person
without using a ladder.

1. Press the four buttons for the present PIN, then press and
hold the # button.

The opener light will blink twice. Release the # button.

2. Press the new 4-digit PIN you have chosen, then press
ENTER.

The motor unit lights will blink once when the PIN has been
learned.

Test by pressing the new PIN, then press ENTER. The door
should move.

TO SET A TEMPORARY PIN

You may authorize access by visitors or service people with a
temporary 4-digit PIN. After a programmed number of hours or
number of openings, this temporary PIN expires and will no
longer open the door. It can be used to close the door even after
it has expired. To set a temporary PIN:

1. Press the four buttons for your personal entry PIN (not the last
temporary PIN), then press and hold the ✽ button.

The opener light will blink three times. Release the button.

2. Press the temporary 4-digit PIN you have chosen, then press
ENTER. The opener light will blink four times.

3. To set the number of hours this temporary PIN will work,
press the number of hours (up to 255), then press ✽.

OR

3. To set the number of openings this temporary PIN will work,
press the number of times to open (up to 255), then press #.

The opener light will blink once when the temporary PIN has
been learned.

Test by pressing the four buttons for the temporary PIN, then
press ENTER. The door should move. If the temporary PIN was
set to a certain number of openings, remember that the test has
used up one opening.

To clear the temporary password, repeat steps 1-3, setting the
number of hours or times to 0 in step 3.

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

WARNING

THE KEYLESS ENTRY BATTERY

The 9 volt battery should produce power for at least one year.
Replace when the keypad illumination becomes dim.

Dispose of old batteries properly.

© 2006, Sears, Roebuck and Co., Sears Canada, Inc.

WARNING