Craftsman 113248320, 113248210 Owner’s Manual

Save ThisManual

ForFutureReference

S _AIRS

owners

manual

Model No.

113.248210

Single Speed Band Saw

with Leg Set

Model No.

113.248320

Two Speed Band Saw

with Leg Set

Illl

113.248320

Model No.

113.248440

Two Speed Electronic

Band Saw with Leg Set

Model No.

113.248510

Two Speed Electronic

Band Saw with Cabinet

S_rial

Number . Model and s_rial numbers

may b_ found at the left-hand side of the bas_.

You should record both

model and s_rial number

in a safe place for futur_

US_.

CAUTION:

READALL

INSTRUCTIONS

CAREFULLY

113.248440

113.248510

CRRFTSMRN

12-INCH BAND SAW

• assembly

• operating

• repairparts

Sold by SEARS,ROEBUCKAND CO., Chicago, IL.60684 U.S.A.

Part No. SP5292 Printed in U.S,A

FULL ONE YEAR WARRANTY ON CRAFTSMAN BAND SAW

If within one year from the date of purchase, this Craftsman Band Saw tails due to adefect in material or workmanship,

Sears will repair it, free of charge.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST BEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.

This warranty applies only while this product is used in the Unltad States.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

SEARS, ROEBUCK AND CO., DEPT. 698/731A Sears Tower, Chicago, IL 60684

TABLE OF CONTENTS

Section Title Page Number General Safety Instructions for

Power Tools .......................... 3

Additional Safety Instructions for

Band Saw ............................ 4-5

Glossary of Terms for Woodworking .......... 6

Electrical Connections .................... 6-7

General Information ...................... 8

Model Description ....................... 8

Unpacking and Checking Contents .......... 8-10

Assembling Leg Set ...................... 11-13

Assembling Cabinet ...................... 13-15

Mounting the Saw to the Cabinet ............ 15-16

Mounting Door .......................... 16

Attaching the Handwheel .................. 17

Mounting the Motor ...................... 17-19

Connecting the Motor ..................... 20

Selecting Blade Speed .................... 21

Recommended Speed Settings ............. 21

Changing Speed Settings ................. 21

Attaching Trim Caps ...................... 22

Getting to Know Your Band Saw ............ 23'

Location and Function of the

Electronic Indicator System .............. 24-25

Installingthe Blade ....................... 26-27

Aligning the Blade and

Blade Guide Assemblies ................. 28-30

Mounting the Front Table .................. 30-32

Squaring the Blade to the Table ............. 32

Adjusting Front Table ..................... 33

Location and Function of Controls ........... 34

Tilting Head for Bevel Cut ................. 35

Adjusting Bevel Lock Knob ................ 35

Basic Band Saw Operation ................ 36

Installing Sanding Attachment .............. 37

Installing the Sanding Belt ................. 37

Recommended Accessories ................ 38

Maintenance ............................ 38-39

Trouble Shooting--All Models .............. 39

Trouble Shooting--Motor .................. 40

Trouble Shooting--Electronics .............. 41-42

Parts Lists ............................. 43-50

Leg Set .............................. 43

Drive Assembly ........................ 44-45

Base Components ..................... 46-47

Bevel Drive and Motor Mount

Assembly Parts ...................... 48-49

Cabinet .............................. 50

GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS

ALL MODELS

1. KNOW YOUR POWER TOOL

Read and understand the owner's manual and labels affixed to the tool. Learn its application

and limitations as well as the specific potential hazards peculiar to this tool.

2. GROUND ALL TOOLS

This tool is equipped with an approved 3-conductor cord and a 3-prong grounding type plug to fit the proper grounding type receptacle. The green conductor in the cord isthe groundi ng wire. Never connect the green wire to a live

terminal.

3. KEEP GUARDS IN PLACE,

in working order, and in proper adjustment and

alignment.

4. REMOVE ADJUSTING KEYS AND WRENCHES

Form habit of checking to see that keys and adj usti ng wrenches are removed from tool before turning it on.

5. KEEP WORK AREA CLEAN

Cluttered areas and benches invite accidents.

Floor must not be slippery due to wax or sawdust.

6. AVOID DANGEROUS ENVIRONMENT

Don't use power tools indamp orwet locations or

expose them to rain. Keep work area well lighted.

Provide adequate surrounding work space.

7. KEEP CHILDREN AWAY

All visitors should be kept a safe distance from work area.

8. MAKE WORKSHOP CHILD-PROOF

-- with padlocks, master switches, or by removing starter keys.

9. DON'T FORCE TOOL It will do the job better and safer at the rate for

which it was designed.

10. USE RIGHT TOOL Don't force tool or attachment to do a job it was

not designed for.

11. WEAR PROPER APPAREL

Do not wear loose clothing, gloves, neckties or

jewelry (rings, wrist watches) to get caught in

moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. Roll long sleeves above the elbow.

12. USE SAFETY GOGGLES (Head Protection)

Wear Safety goggles (must comply with ANSI

Z87.1) at all times. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. Also, use face or dust mask if cutting operation is dusty, and ear protectors

(plugs or muffs) during extended periods of

operation.

13. SECURE WORK

Use clamps or a vise to hold work when practical.

It's safer than using your hand, and frees both

hands to operate tool.

14. DON'T OVERREACH

Keep proper footing and balance at all times.

15. MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for best and safest

performances. Follow instructions for lubricating

and changing accessories.

16. DISCONNECT TOOLS

before servicing; when changing accessories such as blades, bits, cutters, etc.

17. AVOID ACCIDENTAL STARTING

Make sure switch is in "OFF" position before plugging in.

18. USE RECOMMENDED ACCESSORIES

Consult the owner's manual for recommended accessories. Follow the instructions that accom-

pany the accessories. The use of improper acces- sories-may cause hazards.

19. NEVER STAND ON TOOL

Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Do

not store materials above or near the tool such that it is necessary to stand on the tool to reach

them.

20. CHECK DAMAGED PARTS

Before further use of the tool, a guard or other part that is damaged should be carefully checked

to ensure that it will operate properly and perform

its intended function. Check for alignment of moving parts, binding of moving parts, breakage

of parts, mounting, and any other conditions that may effect its operation. A guard or other part

that is damaged should be properly repaired or

replaced.

21. NEVER LEAVE TOOL RUNNING UNATTENDED

Turn power off. Don't leave tool until it comes to a complete stop.

ALL MODELS

additional safety instructions for band saw

Safety is a combination of common sense, staying alert, and knowing how your band saw works.

BEFORE USING THE SAW:

WARNING: TO AVOID MISTAKES THAT COULD

RESULT IN SERIOUS, PERMANENT INJURY, DO NOT PLUG THE SAW IN UNTIL THE FOLLOWING STEPS HAVE BEEN SATISFACTORILY

COMPLETED:

1. Assembly and alignment.

2. Learn the function and proper use of the on-off switch, bevel crank and lock, upper blade guide

• Always wear sM_ty goggles that comply • Before turning saw on, a_lj ust UPPER with ANSI Z87.t BLADE GUIDE to ius! ciell workptece÷

• Before turning law on, check and adju st: • Supp_, fixture or braK;e workpJe_e

a) Blade Tensic)n b) Blade Guides firmly _mnst tabht so it will not rock c) Thrust Searingl or twist Irom y_r hand,

IDANGER I FOR YOUR OWN SAFETY:

WHEN INSTALLING OR MOVING THE SAW

1. To avoid injury from unexpected saw movement: a. Place the saw on a firm level surface where

there is plenty of room for feeding the work- piece.

b. Adjust the saw so the table is level and the saw

does not rock.

c. Bolt the saw to the floor if it tends to slip, slide,

or tip over during operations like cutting long, heavy boards.

d. Turn saw off and unplug electric cord before

moving the saw to a new area.

2. Store and use the band saw indoors.

BEFORE EACH USE

1. Inspect your saw. If any part of this band saw is missing, or bent, or failed in any way, or any electrical componentsdo not work properly, turn the saw off, remove switch key, and unplug the saw. Replace damaged, missing, or failed parts

before using the saw again.

2. Plan your work to protect your eyes, hands, face, ears and body.

a. Do not do layout, assembly, or set up work on

the table while the saw is running.

b. Wear safety goggles (not glasses) that comply

with ANSI Z87.1 (shown on package). Using any power tool can result in foreign objects

being thrown into the eyes, which can result in permanent eye damage. Safety goggles are available at Sears retail or catalog stores. Use

of glasses or use of goggles not in compliance

and lock knob, lower blade guide, tension adjust- ing knob and tension scale, and blade thrust

bearing adjustment.

3. Read and understand all safety instructions and operating procedures throughout the manual.

4. Read the following labels which appear on the

front of the band saw and blade guard.

f----

L___J

Krlow This Tool! Read ind Undersland Owner's Manual before Using this MaChine.

• Plan hand politt _0ns so • sudden •lip • Tt.n _ Off. fro'hove switch key, •rid wMt won't cau_ injury, tot" _4a4e to s|o_ b.efom adjusting _w.

• Turn sew O11 and wa_t for blade to stop char_ltrsg bla<_s or leevir_g arel. b4r/0fe treeing jammed rnaterlal_ • Meintain _/*1"ma=lmum cl4arance betmn

with ANSI Z87.1 could result in severe injury from breakage of the eye protection.

c. For dusty operations, wear aface shield along

with safety goggles.

d. Use extra caution with large, very small, or

awkward workpieces.

1. Use extra supports (tables, saw horses, etc.) forany workpieces large enough to tip

when not held down to the table top.

2. Do not feed small pieces that require your finger holding the workpiece to go under

the guard area. Use jigs or fixtures to hold the work and keep your hands away from

the blade.

. When cutting irregularly shaped work-

pieces, plan your work so it will not pinch

the blade. A piece of molding, for example,

must lay flat or be held by a fixtu re or jig that

will not let it twist, rock or slip while being cut.

4. Properly support round material such as

dowel rods, or tubing. They have a tendency to roll while being cut, causing the b!ade to

"bite." To avoid this, always use a "V" block, or clamp the workpiece to a miter gage.

e. To avoid risk of hearing damage, wear ear

plugs or muffs during extended periods of operation.

fiM.e and sanding belt.

WEAR YOUR

Toavoidbeingsuddenlycaughtintheblade:

1.Donotwear gloves.

2. Remove all jewelry and loose clothing.

3. Tie back long hair.

4. Roll long sleeves above the elbow.

To avoid injury from accidental starting, always unplug saw, turn switch off and remove switch

key before removing the guard, installing or removing any blade, accessory or attach ment,

or making any adjustments.

To avoid slips and jams causing injury:

1. Choose the right size and style blade for the material and the type of cutting you plan to do. Use this band saw to cut and sand only

wood, wood like products and plastic.

2. Make sure the blade teeth point downward toward the table.

3. Make sure the blade tracking guides and thrust bearings are properly adjusted.

4. Always check and correctly adjust blade or sanding belt tension.

To avoid accidental blade contact, minimize blade breakage and provide maximum blade support.

1. Always adjust the upper blade guide and blade guard to just clear the workpiece.

2. Plan your hand placement so your fingers will not be where a sudden slip could cause

them to hit the blade.

Make sure all clamps and locks are tight and there is no excessive play in any parts.

To avoid an electrical shock, make sure your fingers do not touch the metal prongs on the

plug when installing or removing the plug to or from a live outlet.

Never turn your band saw "ON" before clearing

everything except the workpiece and related

feed or support devices off the table,

BEFORE SANDING

1. Keep the table and sanding belt adjusted so the gap between them is no more than 1/16-inch

wide.

2. To avoid fire, shock, or cause electrical shorts, do not sand metal. It could ignite the sawdust

inside the saw.

WHENEVER SAW IS RUNNING

WARNING: DO NOT ALLOW FAMILIARITY (GAINED FROM FREQUENT USE OF YOUR

BAND SAW) TO CAUSE A CARELESS MIS- TAKE. ALWAYS REMEMBER THAT A CARE-

LESS FRACTION OF A SECOND IS SUFFI- CIENT TO INFLICT SEVERE INJURY.

a. If your saw makes an unfamiliar noise or if it

vibrates excessively, stop immediately. Turn the saw off. Remove switch key and unplug the saw. Do not restart until finding and

correcting the problem.

b. Avoid awkward hand positions where a sudden

slip could cause a hand to move into the blade

or the sanding belt.

c, Feed the workpiece only fast enough to let the

blade cut without bogging down or binding.

d. Before freeing jammed material, turn saw off.

Remove switch key. Remove plug from power

source outlet. Wait for all moving parts to stop.

e. When backing up the workpiece, the blade

may bind in the kerf (cut). This Js usually caused by sawdust clogging up the kerr or because the blade comes out of the guides. If this happens:

1, Turn saw off.

2. Unplug saw.

3. Remove switch key. 4, Wait for all moving parts to stop.

5. Remove band saw cover.

6. Stick a flat blade screwdriver or wedge into

the kerf.

7. Turn the upper wheel by hand while backing up the workpiece.

Before removing loose pieces from the table, turn saw off and wait for all moving parts to

stop.

ACCESSORIES

USE ONLY RECOMMENDED ACCESSORIES. Follow the instructions that come with the accessories. Con- sult the owner's manual for recommended accessories.

The use of improper accessories may cause risk of injury to persons.

glossary of terms for woodworking

ALL MODELS

Beveling

An angle cutting operation through the face of the

board,

Crosscut

A cutting operation made across the width of the workpiece.

Compound Cutting

A simultaneous bevel and miter cutting operation. FPM

Feet per minute. Used in reference to surface speed

of blade.

Freehand (as used for band saw)

Performing a cut without the workpiece properly

supported on the work table.

Gum

A sticky, sap based residue from wood products.

Kerr

The material removed by the blade in a through cut or the slot produced by the blade in anon-through or

partial cut.

Leading End

The end of the workpiece which is pushed into the cutting tool first.

Mitering

An angle cutting operation made across the width of the workpiece.

Push Stick

A device used to feed the workpiece through the saw during narrow ripping type operations so the opera- tor's hands are kept well away from the blade.

Resaw

A cutting operation to reduce the thickness of the workpiece to make thinner pieces.

Resin

A sticky, sap based substance that has dried.

Ripping

A cutting operation along the length of the work-

piece.

Sawblade Path

The area of the worktable or workpiece directly in

line with the saw blade.

Set

The distance the tip of the saw blade tooth is bent outward from the face of the blade,

Trailing End

The workpiece end last cut by the saw blade.

Workpiece

The item on which the cutting operation is being performed. The surfaces of aworkpiece are commonly referred to as faces, ends, and edges.

Worktable The surface on which the workpiece rests while

performing a cutting or sanding operation.

electrical connections

ALL MODELS

POWER SUPPLY

Motor Specifications The A-C motor used in this saw is a capacitor-start,

non-reversible type having the following specifica-

tions:

24832

24844

24851

Rated H.P. ...................... 5/8...

Maximum Developed H.R .......... 11/8..

Voltage ......................... 120..

Amperes ....................... 7.9,.

Hertz (Cycles) ................... 60...

Phaze ......................... Single

RPM ........................... 1725.

Rotation of Shaft ................. Clock-

wise

WARNING: TO AVOID ELECTRICAL HAZARDS, FIRE HAZARDS, OR DAMAGE TO THE TOOL, USE

PROPER CIRCUIT PROTECTION. YOUR SAW IS WIRED AT THE FACTORY FOR 120V OPERATION.

CONNECT TO A 120V, 15-AMP, BRANCH CIRCUIT AND USE A 15-AMP FUSE OR CIRCUIT BREAKER.

TO AVOID SHOCK OR FIRE, IF POWER C )RD IS

24821

1/2

120

7.9

Single

1725

Clock-

wise

WORN OR CUT, OR DAMAGED IN ANY WAY, HAVE IT REPLACED IMMEDIATELY.

IF NOT PROPERLY GROUNDED THIS POWER TOOL CAN CAUSE ELECTRICAL SHOCK -- PARTICULARLY WHEN USED IN DAMP LOCA- TIONS CLOSE TO PLUMBING. IF AN ELECTRICAL SHOCK OCCURS THERE IS ALSO THE POTEN- TIAL OF ASECONDARY HAZARD SUCH AS YOUR

HANDS CONTACTING THE SAWBLADE. NOT ALL OUTLETS ARE PROPERLY GROUNDED. IF YOU ARE NOT SURE THAT YOUR OUTLET IS PRO- PERLY GROUNDED, HAVE IT CHECKED BY A QUALIFIED ELECTRICIAN.

Your unit has a plug that looks like the one shown

below.

3-PRONG PLUG

GROUNDED

PROPERLY _-_i /

OUTLET

GROUNDING PRONG

This power tool is equipped with a 3-conductor cord and ground type plug listed by Underwriters' Labora- tories. The ground conductor has a green jacket and

is attached to the tool housing at one end and to the

ground prong in the attachment plug at the other end.

This plug requires a mating 3-conductor grounded type outlet as shown above.

TOOL. Check the saw blade to make sure it turns freely. If the blade is free, try to start the motor

again. If the motor still does not start, refer to the "Motor Trouble-Shooting Chart."

If the motor suddenly stalls while cutting wood, turn the power switch off, unplug the tool, and free the blade from the wood. The motor may

now be restarted and the cut finished.

WARNING: TO MAINTAIN PROPER TOOL GROUND- ING WHENEVER THE OUTLET YOU ARE PLAN- NING TO USE FOR THIS POWER TOOL IS OF THE TWO PRONG TYPE, DO NOT REMOVE OR ALTER

THE GROUNDING PRONG IN ANY MANNER. USE AN ADAPTER AS SHOWN AND ALWAYS CON-

NECT THE GROUNDING PRONG TO KNOWN GROUND.

It is recommended that you have a qualified electri-

cian replace the two prong outlet with a properly grounded three prong outlet.

An adapter as shown is available for connecting the

plug to 2-prong receptacles. The green grounding lead extending from the adapter must be connected

to a permanent ground such as a properly grounded

outlet box.

GROUNDING LUG

ADAPTER I _: _

3-PRONG \_ '._._ _._--< _ CONNECTED TO A

PLUG \ _ " I_II KNOWN GROUND

__._'_' ____,; - .

\\ _ I I{'_T_) il MAKE SURE THIS IS

\_ "/_'"_l_JJJ_l --'" 2 PRONG

_" " _"_--_"_ RECEPTACLE

WARNING: THE ADAPTER ILLUSTRATED IS FOR

USE ONLY IF YOU ALREADY HAVE A PROPERLY GROUNDED 2-PRONG RECEPTACLE.

MOTOR SAFETY PROTECTION

CAUTION: To avoid motor damage this motor should be blown out or vacuumed frequently to keep

sawdust from interfering with normal motor ventila- tion.

1. This tool should be connected to a 120V, 15 amp branch circuit with a 15 amp fuse or circuit

breaker. Failure to use the proper size fuse can result in damage to the motor.

2. If the motor fails to start, turn the power switch to the "OFF" position immediately. UNPLUG THE

4. Frequent "blowing" of fuses or tripping or circuit breakers may result if:

a. MOTOR IS OVERLOADED - Overloading can

occur if you feed too rapidly.

b. LOW VOLTAGE - Although the motor is de-

signed for operation on the voltage and fre- quency specified on the motor nameplate,

normal loads will be handled safely on voltages

not more than 10% above or below the name- plate voltage. Heavy loads, however, require

that voltage at motor terminals equals the

voltage specified on nameplate.

5. Most motor troubles may be traced to loose or incorrect connections, overload, reduced input

voltage (such as small size wire in the supply

circuit) or to overly long supply circuit wire. Always check the connections, the load and the supply circuit whenever motor fails to perform satisfactorily. Check wire size and length with

the Wire Size Chart below.

WIRE SIZES

The use of any extension cord will cause some loss of power. To keep this to a minimum and to prevent

overheating and motor burn-out, use the table below to determine the minimum wire size (AW.G.) exten- sion cord. Use only 3-wire extension cords which have 3-prong grounding type plugs and 3-pole receptacles which accepts the tools plug.

CAUTION: For circuits that are farther away from electrical service box, the wire size must be increased

proportionately in order to deliver ample voltage to the saw motor.

Length of the 120 Volts Wire Sizes Required

Conductor (American Wire Gage Number)

0 - 25 Ft. 16

26 - 50 Ft. 14

51 - 100 Ft. 12

general information

ALL MODELS

1. This manual is for the following Models--

113.248210,113.248320,113.248440, and113.248510.

All sections are labeled withthe correctmodel num- ber.Follow ONLY instructions that are meant for

your model saw.

2. Ifyou aremissing anypart(s)whileputtingyour saw

together, do not continue assembly. Contact your Sears Service Center or Retail Store and get the

missing part(s) before continuing assembly or try- ingto use the saw.

Complete parts lists are located at the end of this manual. Usethese liststoidentifythe number of any

missingpart.

3. Sometimes small parts get lost inpackaging materi- als.Donotthrowaway any packaging untilyoursaw isput together. If you are missinga part, check the packaging before contacting Sears.

unpacking and checking contents

ALL MODELS

Model Description

Model 113.248210: Manual Band Saw; 18x 23 inch work table; sLngle speed; 1/2H.P. motorthat develops 1 H.P.; legset.

Model 113.248320: Manual Band Saw; 27 x 23 inch work table; two speed; 5/a H.P. motor that develops

11/8H.R; legset.

Model 113.248440: Electronic Band Saw; 27 x 23 inch work table; two speed; % H.P. motor that develops 11/8H.P.;legset.

Model 113.248510: Electronic Band Saw; 27 x 23 inch work table; two speed; 5/8 HP. motor that develops 11/8H.P.;23 inch cabinet with door.

TOOLS NEEDED

MEDIUM SCREWDRIVER

PRI-,, SSCREWDRmVE. @

.......... 318" WRENCH

:_ 7/16" WRENCH

SQUARE _/

7116" SOCKET 9/16" SOCKET

1/8" HEX "L" WRENCH

5/32" HEX "L" WRENCH _ SOCKET WRENCH

WARNING: TO AVOID INJURY FROM UNEXPECT- ED STARTING OR ELECTRICAL SHOCK, DO NOT

PLUG THE SAW IN UNTIL ALL ASSEMBLY AND

ALIGNMENT STEPS ARE COMPLETE. THE POWER

CORD MUST REMAIN UNPLUGGED WHENEVER YOU ARE WORKING ON THE SAW.

Unpacking and Checking Contents

1. Separate all "loose parts" from packaging mater- ials and check each item with "Table of Loose

Parts" to make sure all items are accounted for, before discarding any packing material.

9/16" WRENCH

COMBINATION SQUARE MUST BE TRUE

STRAIGHT EDGE GF BOARD 3/4-INCH THICK

THIS EDGE MUST BE

DRAW LIGHT LINE ON BOARD

ALONG THIS EDGIE

f__./

€

t,_

PER_CTLY STRAIGHT

SHOULD BE NO GAP OR OVERLAP HERE WHEN SQUARE IS FLIPPED OVER IN DOTTED POSITION

WARNING: IF ANY PARTS ARE MISSING, DO

NOT ATTEMPT TO ASSEMBLE THE BAND SAW, PLUG IN THE POWER CORD, OR TURN

THE SWITCH ON UNTIL THE MISSING PARTS ARE OBTAINED AND ARE INSTALLED COR- RECTLY.

2. Remove front table and front cover first while saw is being unpacked. TO remove the front

cover, pull thecover at the neck and underside of throat area.

TABLE OF LOOSE PARTS

ITEM DESCRIPTION QTY.

A Motor ............................... 1

B Basic Saw Assembly .................. 1

(Models 113.248210 and 113.248320 Do not include electronic

indicator system)

C Owners Manual ....................... 1

D Trim Cap, L.H ......................... 1

E Trim Cap, R.H ........................ 1

F Leg ................................ 4

G Lower Stiffener ....................... 4

H Sanding Platen ....................... 1

I Poly "V" Drive Belt .................... 1

NOTE: To avoid damage to the band saw leave it

laying on its left side until you are ready to mount it to the leg set or cabinet. To prevent scratching the finish, lay a piece of the packing box under the saw.

J Pulley ............................... 1

K Loose Parts Bag

containing the following items:

Band Saw Blade 1/4 x 80 ................ 1

Sanding Belt 1/2 x 80 ................... 1

Handwheel Asembly ................... 1

Bag of Loose Parts #508014 ............. 1

Bag of Loose Parts #507968 ............ 1

Bag of Loose Parts #507741 ............. 1

Battery (Electronic Models Only) ......... 1

L Cabinet Assembly (Model 113.248510 Only) 1

M Leg Channel ........................ 1

D E

ALL MODELS

LIST OF LOOSE PARTS IN BAG #507968

ITEM DESCRIPTION QTY.

A Truss Head Screw 1/4-20x12 ............ 32

B Lockwasher Ext. t/4 .................... 32

C Hex Nut 1/4-20 ........................ 32

D Leveling Foot ......................... 4

E Hex Jam Nut 3/8-16 .................... 8

F Bracket Leg .......................... 4

LIST OF LOOSE PARTS IN BAG #508014

ITEM DESCRIPTION QTY.

G Pan Hd. Screw 10-32 x 2 ................ 1

H Hex Nut 10-32 ........................ 1

I Switch Key ........................... 1

J Lo Hd. Screw Cap 1/4-20x si8 ............ 2

K Spacer #10 x 5As ...................... 3

L Hex Flange Lock Nut 10-32 .............. 4-

M Locking Setscrew 1/4-20x 1/2............. 3

N Wingnut %s-18 ........................ 1

O Washer 7/32x1x11,4s .................. 1

0 Washer 13/64x s/ex 1/32.................. 2

P Pan Hd. Screw Type TT 10-32 x 3/8........ 2

Q Hex Hd. Screw Ty TT 1/4-20x % .......... 4

_] t_\\\/\\\_\\\\\\\_\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\_e

i,v

K L M

LIST OF LOOSE PARTS IN BAG #507741

ITEM DESCRIPTION QTY.

R Table Alignment Key ................... 1

S Table Latch .......................... 2

T Belt Tension Stud ..................... 1

U Table Latch Spring .................... 2

V Table Alignment Spring ................. 2

W Key 3/16Sq. x 15,46..................... 1

P O*

*NOT SHOWN TO SCALE

assembly and alignment

MODEL 113.248210, 113.248320,

113.248440

ATTACHING LEVELING FEET

From the loose parts bag find the following hardware:

Item Description Qty.

A Support Bracket .................... 4

B Leveling Feet ...................... 4

C Hex Nut 3/8-16...................... 8

From the loose parts find the following items:

D Leg .............................. 4

*NOT SHOWN TO SCALE

1. Mount floor leveler support brackets inside legs. Line up the three tabs on brackets with slots on leg and tap into place. Make sure lip on bracket points

up. Install the remaining three brackets the same way.

2. Put ahex nut on each of the leveling feet and screw it down towards the rubber foot.

3. Put the leveling feet through the holes in the bottom of the floor leveler support bracket.

4. Put another hex nut on each of the leveling feet_.nd

hand tighten until they are next to the support bracket.

LEG

SUPPORTBRACKET

NUTS

WARNING: After the legset has been attached to the basic saw assernbly, it will be necessary to adjust the

leveling feet so the saw does not rock.

SUPPORT BRACKE ___,,.,_,.

LEVELING FOOT

MODEL 113.24821 O, 113.248320,

1113.248440

ATTACHING LEG SET

From the loose parts bag findthe following hardware: Item Description Qty.

A Truss Head Bolts 1/4.20x 1/2........... 32

B Lockwashers External 1/4 ............. 32

C Hex Nuts 1/4-20..................... 32

From the loose parts find the following items:

D Leg Channel ....................... 1

E Legs (with attached support brackets and

leveling feet) 4

F Lower Stiffeners .................... 4

1. Lay a piece of cardboard on the floor to keep from scratching the saw.

2. Position the basic saw assembly on the floor as shown below. The back cabin et ofthe saw should be

laying flat on the floor. It may be necessary to have someone help you lift the saw.

_*NOTSHOWN TO SCALE

Switch

=_ont

Side ,/_/_J_//_1 __.Front Leg s Are

tt__._ _ Artacbed Here

_ Leg

3. Mount the two front legs to the basic saw assembly using truss head bolts, Iockwashers, and nuts. Make sure that the four (4) holes in each corner of the saw line up with the four (4) holes in the top of each leg. At thistime only put bolts through thesides ofthe saw assembly notthe front. Onlyfinger tighten

nuts.

4. Position the leg channel inside the legset as shown.

Fasten the channel piece, leg, and saw together

with two (2) truss headbolts on each side. The threaded section of the bolts should point towards

the inside of the basic saw assembly. Put a lock-

washer and hex nuton each bolt. Finger tighten nuts atthis time.

J[ t_'/ \ Rear Legs Are L_._/_Attached_ __ _ Here

\ Floor

SAW

BAS E

LEG

TRUSS HEAD

SCREW

LOCKWASHER

Trusshead screw, Iockwasher, hex nut, and front channel piece.

Use truss head bolts, Iockwashers, and hex nuts to mount the two (2) rear legs to the basic saw assem-

bly. It may be necessary to slightly tilt the saw as- sembly backwards in order to get the four (4)holes in each corner of the saw to line up with the four (4)

holes in the top of each leg. Finger tighten nuts at this time.

Attach the four (4) lower stiffeners to the legs. Two (2) truss head bolts, washers, and hex nuts are re-

quired to hold each end of alowerstiffener in place. Only hand tighten hex nuts.

7. Go back with a 7/_6wrench or socket and tighten all hex nuts.

8. Carefully lift the saw into its normal position. It may be necessary to have someone help you in order to avoid damaging the saw.

ADJUSTING LEVELING FEET WARNING: TO AVOID INJURY FROM UNEX-

PECTED SAW OR WORK MOVEMENT, LEVEL- ING FEET MUST BE ADJUSTED SO THAT SAW

DOES NOT ROCK.

Toadjust leveling feet so the saw will sit properly: a. Move saw to desired location.

b. Raise or lower leveling foot by turning itclockwise or

counterclockwise.

c. Tighten nuts to lock leveling foot in place.

TRUSS HEAD BOLT"-'-'_' .-J.__

,._j_ WASHER

LEG . _ _S_/_ :1i

///_ ,,/LL_--_ --

i S FFE.ER

HEXNu,

MODEL 113.248510

ASSEMBLING CABINET

1. Separate all "loose" parts from packing materials and check each item with "Parts List" to make

sure all items are accounted for before discard-

ing any packing material.

From loose parts find the following items:

ITEM DESCRIPTION QTY.

1 Right Side Panel ...................... 1

2 Left Side Panel ....................... 1

3 Lower Shelf .......................... 1

4 Skirt ................................ 2

5 Shelf Stiffener ........................ 1

6 Corner Bracket ....................... 2

7 Spacer .............................. 2

8 Door ................................ 1

Bag of Loose Parts #508166 Containing Following Items:

Screw, Truss Hd. 1/4-20 x 1/2 ................ 34

Lockwasher, Ext. 1/4 ...................... 34

Nut, Hex 1/4-20 .......................... 34

Foot, Leveling 3/8 ......................... 4

Nut, Hex Jam 3/8-16 ....................... 8

Bag of Loose Parts #507530

(In Cabinet Assembly) Containing Following Items:

Screw, Pan Hd. #6-10 x 1/2 .................. 2

Screw, Pan Hd. Ty "T" 6-32 x 318 ............. 2

Screw, Pan Hd. #10-10x 1/2 .................. 4

Catch Magnetic ........................... 1

Hinge Door .............................. 2

MODEL 113.248510

2. After layout of cabinet parts, take the lower shelf and turn upside down on floor. Small front flange should be pointing upward.

3. Locate the two (2) corner brackets, four (4) 1/4- 20 x 1/2 truss head bolts, Iockwashers, and nuts.

Attach the corner brackets to the front flange in

holes as illustrated. Attach both corner brackets.

4. Locate the two (2) side panels, one (1) shelf stiffener, and six (6) 1/4-20 x 1/2truss head bolts, Iockwashers and hex nuts. Place the right side panel on its back side as illustrated. Stand up the lower shelf on the rear flange and line up the

holes on the corner bracket and shelf stiffener with the holes in the side panel. Mount the bolts

in the three holes and tighten hex nuts with a 7/16-inch wrench or socket. Repeat procedure

for left side panel.

o o o o

LOWER

SHELF

CORNER /_

BRACKETS 7_

\ ,/:o:

CORNER BRACKETS

SHELF

SHELF STIFFENER PANEL

RIGHT SIDE

5. Locate the two(2) skirts, eight(8) truss head bolts, Iockwashers and hex nuts. Assemble one(l) skirt to

the front of the cabinet using four(4) bolts, lock- washers and nuts. Hand tighten only. Stand the cab-

inet upright and assemble the rear skirt to the cabinet using two(2) truss head bolts Iockwashers

and nuts using the top two holes only. From inside the cabinet insert two bolts out through the two remaining holes in the rearskirt. Installlockwashers and nuts hand tightened only.

REAR SKIRT

LEFTSIDE

PANEL

REAR FLANGE

SHELF

/...i RIGHT SIDE PANEL

FRONT

SKIRT

MODEL 113.248510

6.Secure rear of shelf to right side and left side panels using (2) 1/4-20 x 1/2 truss head bolts and hex nuts.

Hand tighten only.

7. Locate the right and left side spacers, the six (6) 1/4-20 x 1/2 truss head bolts, Iockwashers, and

hex nuts. Position the spacer inside the right and left side panels and fasten in the three holes as illustrated. Tighten nuts using a 7/16-inch wrench

or socket.

LOCKWASHER

NUT

SPACER

Locate four (4) leveling feet and eight (8) 3/8-16 hex nuts. Attach the leveling feet to bottom of

side panels in front and rear as illustrated. Hand tighten hex nuts.

WARNING: TO AVOID INJURY FROM UN- EXPECTED SAW OR WORK MOVEMENT,

LEVELING FEET MUST BE ADJUSTED SO THAT SAW DOES NOT ROCK.

To adjust leveling feet so the saw will sit properly:

a. Move saw to desired location. b. With 9/16-inch wrench loosen bottom nut.

c. Back off top nut by hand.

d. Raise or lower foot by adjusting bottom nut

using 9/16-inch wrench.

e. Snug top nut against inside of leg by hand.

f. Adjust all four feet as necessary then tighten

all four bottom nuts using a 9/16-inch wrench.

1/'4-20 x 1!2 RIGHT SIDE PANEL

MOUNTING THE SAW TO THE CABINET

1, From loose parts bag find the following hard-

ware:

ITEM DESCRIPTION QTY.

A Truss Head Bolts 1/4-20 x 1/2 .......... 4

B Lockwashers External 1/4 .............. 4

C Hex Nuts 1/4-20 ....................... 4

c©

MODEL 113.248510

2. Place saw on cabinet so that holes in bottom of saw line up with holes in top of cabinet.

3. Install bolts, Iockwashers, and nuts as shown. Tighten securely using a 7/16-inch wrench or

socket. The front two bolts hold the saw, lower wheel cover, and the cabinet together. Install these bolts from the bottom side,

4. After the band saw has been mounted to the

cabinet, go back and tighten all the nuts that were previously hand tightened using a 7/16-

inch wrench or socket.

FRONT

MOUNTING DOOR Tools needed: 7/16" wrench or socket and phillips

screwdriver.

1. Locate the two (2) door hinges and four (4) 10-10 x 1t2 plastite screws. Mount hinges on either side of the door withphillips screwdriver.

2. Locate the four (4)truss head bolts, Iockwasher and

hex nuts to attach door hinges to the side panel. Tighten hex nuts with a 7/16" wrench or socket.

3. Locate the magnetic catch, the magnetic catch stop

plate, two (2) 6-10 x 1/2 pan head screws and two (2)

6-32 x 3t8 pan head screws. Attach the magnetic

catch to the door with the two (2) 6-10 x 1/2 pan head screws using a phillips screwdriver. Attach the mag- netic catch stop plate to the side panel opposite the

side the hinges are to be mounted. Use the two (2) 6-32 x 3/8 pan head screws to mount stop plate.

Adjust the stop plate if necessary with phillips screw- driver for desired closure.

;IDE PANEL

MAGNETIC CATCH

STOP PLATE

MAGNETIC

CATCH

+ 36 hidden pages