Product Guide
VITM4-2CH-2S
Vitesse Modular 4 - 2 Ch / 2 supply Switching Modules
Overview
The Vitesse modular system is a cost effective method of providing power and control for lighting installations in in-
dustrial, commercial and retail buildings. The system is designed for ease of installation: mains input is connected
using the spacious wiring compartment; control inputs and outputs are pluggable using industry standard connectors.
The modular approach allows for between 4 and 16 luminaires to be connected.
The VITM4-2CH-2S is a two channel, non-dimming distribution box for use in applications that require two independ-
ent supplies for switching lighting or lighting and ventilation circuits. For example this product is ideal for installations
that have essential and non-essential supplies for lighting circuits and require common switching using presence detectors. This product provides connections for separate Live, Neutral and Permanent Live inputs.
System Components
202mm
150mm
146mm
127mm
Channel 1 Channel 2 Channel 1
VITM4-S-2CH-2S
Vitesse modular starter for non-dimming systems
Height - allow 150mm for total height of unit (including connectors and cable)
Fixing points
VITM4-E-2CH-2S
Vitesse modular extender f or non-dimming systems
122mm
75mm
Channel 2
9 pole interface
connector and lead
supplied with
detectors
Installation
BESA box fixings
Channel for channel nuts (zebs)
3 x Ø20mm knockouts for rear
cable entry
4 x key slots to accept M6 (1/4”)
fixings
Removable gland plate with
3 x Ø20mm knockouts
Warning. This device works at mains voltage. Be sure to take care when working with electricity.
The box should be fixed on a smooth, flat surface or using drop rod fixings attached to channel nuts.
Ensure that there is easy access to the wiring compartment and all connectors once the box is in-situ.
Wiring
Permanent Live 1
Neutral 1-Supply in
Earth
Live 1-Switched
Live 2-Switched
Neutral 2-Supply in
Permanent Live 2
Live 1-Supply in
Large
cables
Small
cables
Channel 1
Channel 2
Live 2-Supply in
Cable clamps
All wiring should be mains rated.
Remove wiring compartment cover.
Wire the box using the diagrams below
Switched live turns the lights on and off
Use the cable clamps to secure the wiring or use cable glands
(not supplied). The clamps can be split, and flipped over to
clamp different cable diameters.
Replace wiring compartment cover.
Plug in the luminaires ensuring that the connector latches to
the box.
Connecting a detector
Luminaire connections / Lead colours
Permanent Live Black (4 core only)
Neutral Blue
Earth Green / Yellow
Switched Live Brown
Detector lead needs to be ordered separately from the
detector. Order code VITM4-L3-2CH-2S.
Where two detectors connect to a single box a dual
lead is available VITM4-LD3-2CH-2S.
CH1 and CH2 plugs are coded.
Ensure that the plugs are
inserted correctly and do not
apply excessive force
Sensor
2
Local emergency test switch
Wiring
N1
N2
E L1
L2
Local emergency test switch supply 1
Local emergency test switch supply 2
Emergency test using central switch
N1 E
N2
L2 L1
Local emergency
test switch supply 1
Multiple boxes
Local emergency
test switch supply 2
Emergency test using power interruption
N2
N1 E
L1 L2
Wire link 1
Wire link 2
A local lighting switch may still be used when there
is a central emergency test switch or when a circuit
breaker is used to interrupt the power.
3
DO NOT WIRE ACROSS
PHASES
Applications
2 Channel detectors
The flexibility of using two channels detectors allows the following scenario:
Channel 1 - occupancy and lux
Channel 1 of the detector can be used to switch the Channel 1 luminaires at a preset lux level. These luminaires
are typically situated nearest the windows. The luminaires will also switch with occupancy.
Channel 2 - occupancy only
The inner luminaires, ie those furthest from the windows, are switched with occupancy only.
Presence detectors
The unit can only be used in presence mode only, ie automatic on, automatic off.
The diagrams below illustrate a typical application.
Window / room switching
Window / room switching + Extender
4
This page intentionally left blank
5
This page intentionally left blank
6
This page intentionally left blank
7
Part numbers
Presence / Absence Detectors
EBDSPIR-PRM-2CH PIR 2-Channel presence detector
EBDSPIR-PRM-2CH-NC PIR 2-Channel presence detector, normally closed fail safe contacts
MWS3A-PRM-2CH Microwave 2-Channel presence detector
MWS3A-PRM-2CH-NC Microwave 2-Channel presence detector, normally closed fail safe contacts
MWS6-PRM-2CH Microwave 2-Channel presence detector
MWS6-PRM-2CH-NC Microwave 2-Channel presence detector, normally closed fail safe contacts
Modules
VITM4-S-2CH-2S 4 pole starter box, 2 channel, 2 supplies
VITM4-E-2CH-2S 4 pole extender box, 2 channel, 2 supplies
Detector Leads (LSF)
VITM4-L3-2CH-2S 3m 2 channel sensor lead, 2 supplies
VITM4-LD3-2CH-2S 3m 2 channel dual detector sensor lead, 2 supplies
Luminaire Leads (LSF)
VITM4L303100W 3 core 3m 1.0mm2 White plug
VITM4L305100W 3 core 5m 1.0mm2 White plug
VITM4L403100R 4 core 3m 1.0mm2 Red plug
VITM4L405100R 4 core 5m 1.0mm2 Red plug
Other leads available to order.
Connectors
VITM4-LPW 4 pole luminaire plug white
Ratings
Voltage 230VAC +/- 10%
Frequency 50Hz
Terminal capacity 4mm2 in wiring compartment
Temperature 0ºC to 35ºC
Power Rating of system 16A. Rating of each output 10A
Note: detector may have different rating, check datasheet
Compliance BS 5733:1995
For lighting purposes only with suitable circuit protection. For fixed wiring only
IMPORTANT NOTICE!
This device should be installed by a
qualified electrician in accordance with
the latest edition of the IEE wiring
regulations.
FM 45789 EMS 534520
Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice.
8
UK Patent no. GB2463063
EU patent pending
EU registered design no.
001587544-0001, 001587544-0002
C.P. Electronics Ltd
Brent Crescent
London
NW10 7XR
United Kingdom
Tel: + 44 (0) 333 900 0671
Fax: + 44 (0) 333 900 0674
www.cpelectronics.co.uk
enquiry@cpelectronics.co.uk
Ref: #WD326 Issue 4
Loading...