Cornelius WCC700 User Manual

IMI CORNELIUS INC.

One Cornelius Place
Anoka. MN 55303-6234
Telephone [phone]
Facsimile (763) 422–3246

DUAL DF/ED 2XX LID KIT FOR THE FOLLOWING ICE

MAKERS: Cornelius Extreme 522 and Wilshire WCC 700

Dispenser DF/ED 2XX
Kit Number 629087947

Components Qty

1. Cover 620043547 2

2. Lid Assembly (XAC 522 Icemaker) 620046064 1

3. Lid Assembly (WCC 700 Icemaker) 620046060 1

4. Mounting Bracket 22127 4

5. Screw, #8 SM 70217 20

6. RTV 50904 1

7. Label 91957 2

8. Instructions 620919550 1

9. Nut, Nylon 620701902 4

10. Washer, Nylon 620701903 4

11. Washer, Sealing 620701901 4

12. Ice Baffle 620037003 2

13. Gasket Strip 620505802 2

14. Binstat Kit 631500109 1

15. Plate, Top Cover 620044644 1

1. Unpack kit. Refer to Figures 1 & 2 for component detail.

2. Attach the ice baffles (item 12) to the lid assemblies (items 2 & 3) using the gasket strips, washers and acorn
nuts provided (figure 1).

3. Replace the center–mounting bracket supplied with the dual merchandiser kit with the top cover plate sup­plied with this kit (item 15). Failure to do this will prevent the adapter kit from functioning properly.

4. Set the lid assembly onto the dispenser. Using the slotted holes on the side of the lid as a template, drill four
(4) 9/64” diameter holes at the bottom of the slots (Figure 2).

Note: Use extreme care not to drill into the hopper. Use a drill stop to ensure that the drill bit does not
penetrate deeper than ¼” past the sheet metal. Failure to do so could result in a hole in the hopper, great­ly reducing the efficiency of both the dispenser and ice maker.

5. Fasten the lid to the dispenser with four (4) #8 sheet metal screws (item 5), two on each side.

6. Seal the ice maker to the top of the dispenser as follows:
A. Run beads of RTV (item 7) around the opening in the lid assembly and the inside of the perimeter of the

ice maker outline so that the ice maker will set on the RTV. Make sure that some RTV is applied inside

the nutserts on the lid assembly.
B. Set the ice maker onto the lid and position it as required.
C. Insert the thumbscrews (item 5) into the lid to attach the icemaker to the lid (Figure 3).
D. Wipe away the excess RTV.

EIMI Cornelius Inc; 2001

November 30, 2001

Revision A

620919550

7. Attach the mounting brackets (item 4) to the to the ice makers and lid assemblies with the the #8 sheet metal
screws (item 5) (figure 2).

8. Follow the ice maker manufacturer’s instructions to complete the installation of the ice maker.

9. Install the bin–stat (item 14) per the instructions provided with that kit.

10. Install the covers (item 1) into the slots on the lid assemblies (figure 3).

11. Apply the label (item 6) on the front of the cover.

EIMI Cornelius Inc; 2001

November 30, 2001

Revision A

620919550

13

10

11

9

SECTION W–W

SCALE 0.625

9

4X

10

4X

12

4X

11

2X

2X

13

12

EIMI Cornelius Inc; 2001

FIGURE 1. PARTS

November 30, 2001

Revision A

620919550

DRILL ø 9/64 (.140) HOLES

USING BOTTOM OF SLOTTED
HOLES AS A TEMPLA TE.

WCC700 ICEMAKER

EXTREME 522 ICEMAKER

VIEW X

SCALE 0.250

2X

1

2X

SEE FIGURE(S) 3a & 3b

4X

4

5

16X

7

3

SEAL ICEMAKER(S) TO

2

ITEM 2 AND 3 WITH
ITEM 6 (RTV)

4X

5

REPLACE ITEM 5–ED2XX DUAL–LIGHTED

MERCHANDISER KIT WITH

P/N 620044644

EIMI Cornelius Inc; 2001

FIGURE 2. DISPENSER ASSEMBLY

November 30, 2001

SEE VIEW ”X”

Revision A

620919550

WCC700 ICEMAKER

1

FIGURE 3a. CLOSED POSITION

SCALE 0.250

EXTREME 522 ICEMAKER

LID ASSEMBLY

WCC700 ICEMAKER

1

EXTREME 522 ICEMAKER

LID ASSEMBLY

EIMI Cornelius Inc; 2001

FIGURE 3b. OPEN POSITION

SCALE 0.250

November 30, 2001

Revision A

620919550