Cornelius P-N 620204721 User Manual

ED/DF175 22” CCM322/522 Nordic Style Lid Kit Installation Instructions

INSTALLATION INSTRUCTIONS

ED/DF175 22” CCM322/522 NORDIC BLACK/GRAY STYLE LID KITS

This Nordic style kit applies to the Cornelius 22” wide CCM322/522 ice maker.

Item

No.

1 620043511

2 620046011 Lid Assembly 1
3 22127 Bracket 2
4 70217 #8 Screw 12
5 50904 RTV 1
6 90221 Label 1
7 620204721INS Installation Instruction 1
8 620701902 Acorn Nut, 8–32 Nylon 2

9 620701901 Sealing Washer 2
10 620037007 Ice Baffle ED150 1
11 621701903 #8 Nylon Washer 2
12 630500109 Bin Stat 1

CAUTION: Disconnect electrical power to the dispenser before proceeding with the icemaker
adapter kit installation.

WARNING: The dispenser must be secured with 3/8-16 bolts (6) to the counter before installing
this Icemaker Adapter Kit. Refer to the installation manual and Figure 2 for the counter mounting
template.

Part No. Name Qty.

Cover, Gray

620043512

Cover, Black

1

1. Unpack Kit.

2. Insert baffle assembly into the adapter lid.

3. Place (2) sealing washers (item 9) over studs and (2) flat washers (item 11), then fasten in place
with (2) plastic acorn nuts (item 8).

4. Set ice maker lid on the top of the dispenser.

5. Using the slotted holes in the lid as a template, drill four (4) .140_ diameter (9/64_) holes at the
bottom of the slots (see detail A). Use extreme care not to drill into the hopper. Fasten the lid to the
dispenser with four (4) #8 sheet metal screws, two on each side.

6. Seal the ice maker to the top of the dispenser as follows:
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker

outline so that the ice maker will set on the RTV.

B. Set the ice maker onto the lid and position it as required.
C. Wipe away the excess RTV.

7. Drill 9/64” diameter holes into the ice maker cabinet using the bracket as a template. Use extreme
care not to drill into any ice maker components (condenser, tubing, etc.). Secure the brackets using
the screws provided.

8. Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in
the bottom of the ice maker. Wrap the eye of the wireform over the stud near the hole to the end of
the wireform bracket and wrap the tube around the end of the bracket several times, insuring the
tube is secure.

NOTE: The bin stat must not interfere with the agitator rotation or in the path of ice falling from
the icemaker. If it interferes with the agitator or in the path of ice, bend the bracket out of the way.

Release Date: October 5, 2007 www.cornelius.com Revision: A
© 2007, IMI Cornelius Inc. - 1 - Publication Number: 620204721INS

ED/DF175 22” CCM322/522 Nordic Style Lid Kit Installation Instructions

9. If the plastic acorn nuts interfere with the positioning of the plastic manual fill cover, it may be
necessary to make small notches in the back flange of the cover to clear the acorn nuts.

10. The unit is now ready for operation.

Figure 2. Mounting Template

ICEMAKER

SEAL ICEMAKER

TO ITEM 2 WITH

ITEM 5 (RTV)

4

8 PLACES

6

4 PLACES

4

3

2

1

VIEW A

FIGURE 1. ED/DF175 Kit

Publication Number: 620204721INS - 2 - © 2007, IMI Cornelius Inc.