Cornelius JETSPRAY LT1, JETSPRAY LT1-WI6, JETSPRAY LT1-W25, A1371, A1456 Owner's Manual & Parts List

YourStandardof ExceUencefor BeverageMerchandisingonSix Continents

Document No . 11341

Revision N 0

December

1994

Printed in

the

USA

Manufa ctured b y Jet Spray Corpora tion

825 Univers ity Avenue ,

P.O.

Box 8250,Norwood,

MA

02062

This manual applies to models of
Serial Numbe r 314936 or higher .

Mmw...

LTI
LTl-WI6
LTl-W25

Instant Liquid Iced Tea Dispenser

J6J=-==-..r

":,::-",,, "'\ ~~rpITS

LIST

B

*EXPORT MODEL LT1-W25 REOUIRES A 220/240V 50HZ OUTLET

-1-

5.

J[j

Remove drip tray and grille.
Remove front panel assembly from unit by

lifting up and pulling out from the bottom .

(See sketch.)

4.

3. Place

flare gasket in check valve and connect to water
inlet at rear of unit. (See instruction sheet
included with check valve.) Connect a 1/4" 00 copper

water line to the fitting on the check valve and to a

30-125 psig water supply. Water line should be long
enough so that unit can be moved for cleaning.

2. Do not plug in the unit.

1. Place dispenser on a flat, sturdy surface accessible to
a 115 volt 60Hz* outlet and a 30-125 psi water supply.

It is recommended that a shutoff and an 80/100 mesh
strainer be installed in the water line.

A. INSTALLATION INSTRUCTIONS:

A water line is connected to the solenoid valve through a fitting

located on the rear panel of the unit. A one gallon container of

tea concentrate is placed inside the unit through the removable

front panel. A product tube is placed inside the gallon
container of tea concentrate , and runs up to the mixing block.

When the push handle is depressed it closes a switch, acti vating

the solenoid valve, allowing water to pass through the mixing
block. The pressure drop in the mixing valve allows syrup to be
siphoned from its container, mixed with water, and dispensed out
the outlet tube.

BRIEF DESCRIPTION OF HOW THE UNIT WORKS

The Model LT1 is intended for commercial use. It is a compact,

lightweight, countertop unit designed to dispense a mixture of
tea concentrate and water simply by activating a push handle.
The proper electrical outlet, one gallon of tea concentrate, and

a water source are all that is required to set the dispenser

into operation.

Instant Liquid Iced Tea Dispenser

MODEL LT1

© 1994-2014, Cornelius Inc.

Publication Number: 11341IPL

-2-

1. Drip tray, grille, and product tube assembly may be
washed in warm soapy water, such as Joy. Rinse
thoroughly in potable water.

2. Clean the outside of the dispenser with a clean damp

cloth and mild soap.

C. CLEANING UNIT

2. To adjust this ratio for a richer or weaker drink, use

the 1/8" Allen wrench packed in the drip tray.

Adjustments are made through a hole located in the

upper right hand side panel. using the 1/8" Allen

wrench, turn the adjusting screw counterclockwise for

a richer drink and clockwise for a weaker drink.

1. The ratio of concentrate to water is factory set for a

5 to 1 mix.

B. RATIO CONTROL - CONCENTRATE TO WATER

*EXPORT MODEL LT1-W25 REQUIRES A 220/240V 50HZ OUTLET

12. unit is now set for operation.

11. Depress push handle to prime unit.
NOTE: Draw approximately 12 oz. until product line is

full.

10. Turn on power switch, located on rear of unit.

7. Replace front panel assembly.

8. Replace drip tray and grille.

9. Plug power cord into 115 volt 60Hz* outlet.

6. Remove cap and product tube assembly from inside unit.
Place cap and product tube in a full gallon of
concentrate. Slide container of concentrate into unit

making sure that the plastic line from the product tube

assembly is not crimped in any way.

Publication Number: 11341IPL

© 1994-2014, Cornelius Inc.