Cornelius Flavor Fusion 22127 User Manual

Icemaker & Adaptor Hold-Down Kit Installation Instructions

INSTALLATION INSTRUCTIONS

ICEMAKER AND ADAPTER HOLD-DOWN KIT P/N 629096853

F

OR FLAVOR FUSION / IDC UNITS ONLY

Instructions for Non-30 Inch Wide Icemaker – Flavor Fusion Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Instructions for 30 Inch Wide Icemakers – Flavor Fusion Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Instructions for Non-30 Inch Wide Icemaker – IDC Series Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Instructions for 30 Inch Wide Icemaker – IDC Series Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Parts Included in the Kit are Shown in Table 1:

Table 1

Part No. Description Qty.

22127 Icemaker Rear Mounting Plate 2
50904 Silicone sealant 1 tube
620053922 Left Side Adapter Hold-Down Bracket 1
620053923 Right Side Adapter Hold-Down Bracket 1
620518916 Adaptor/Icemaker Side Hold-Down Plate (Flat) 2
620701601 #10-16 S.S. Sheetmetal Screws 12

Tools Needed:

• Power Drill

• 9/64 in. (.140 in.) Drill Bit

• #2 Phillips Head Screwdriver

INSTRUCTIONS FOR NON-30 INCH WIDE ICEMAKER – FLAVOR FUSION UNITS

WARNING: Failure to follow the installation instructions correctly may result in equipment damage

and/or personal injury.

The Parts shown in Table 2 are NOT Used for this Installation:

Table 2

Part No. Description Qty.

620518916 Adaptor/Icemaker Side Hold-Down Plate (Flat) 2

1. Remove the two top black side panel screws from both sides of the Flavor Fusion unit (See Figure 1) and
save the screws.

Release Date: June 30, 2008 www.cornelius.com Revision: 1
© 2008, IMI Cornelius Inc. - 1 - Publication Number: 629096853INS

Icemaker & Adaptor Hold-Down Kit Installation Instructions

Side Panel

Screws

Figure 1

2. Locate the two right and left side hold down brackets, shown in Figure 2. These are the brackets with the
bent flange on them.

Left Side

Right Side

Figure 2

Straight Edge Goes
to the Rear of the
Dispenser

3. There are two options for installing the brackets, outside of the side panels or behind the side panels, as
shown in Figure 3. Left side of unit is shown in Figure 3.

Figure 3

4. Place the bracket over the adapter lid then re- install the black screws that were removed in Step 1.

Publication Number: 629096853INS - 2 - © 2008, IMI Cornelius Inc.

Icemaker & Adaptor Hold-Down Kit Installation Instructions

Flange on bracket
MUST Go Over the
Top of the Adapter
Lid as Shown.

Figure 4

5. Repeat Steps 1 through 4 for the opposite side of the dispenser.

6. Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 5.

Run a Continuous
Bead of Caulking
Around the Adapter
Top

Figure 5

7. Locate the icemaker mounting plates at the rear of the icemaker and positi on as shown in Figure 6, if plates
are not already installed.

NOTE: Kit contains two plates, both mounting plates must be installed.

Figure 6

8. Using the plate as a template, drill 9/64 in. (0.140 in.) holes into the icemaker base and the dispenser, as
shown in Figure 7.

© 2008, IMI Cornelius Inc. - 3 - Publication Number: 629096853INS