Cornelius CCM630, CCM830, CCM330, CCM530, CCM430 User Manual
ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
INSTALLATION INSTRUCTIONS
ED2XX 30” CCM330/430/530/630/830/1030 NORDIC BLACK/GRAY
S
TYLE LID KITS
This Nordic style kit applies to the Cornelius 30” wide CCM322/522 ice maker.
Item
No.
1
2 15537 Lid Assembly 1
3 29565 Bracket 2
4 70217 #8 Screw 6
5 50904 RTV 1
6 90221 Label 1
7 620204731INS Installation Instructions 1
8 620701902 Acorn Nut, 8--32 Nylon 2
9 620701901 Sealing Washer 2
10 620037003 Baffle, Ice 1
11 621701903 #8 Nylon Washer 2
12 620505802 Insulation Strip 1
13 630500109 Bin Stat 1
CAUTION: Disconnect electrical power to the dispenser before proceeding with the icemaker
adapter kit installation.
1. Unpack Kit.
2. Place insulation strip (item 12) over studs on the baffle and insert baffle assembly into the adapter
3. Place (2) sealing washers (item 9) over studs and (2) flat washers (item 11), then fasten in place
4. Set icemaker lid on the top of the dispenser.
5. Using the slotted holes in the lid as a template, drill four (4) .140_ diameter (9/64_) holes at the
6. Seal the icemaker to the top of the dispenser as follows:
7. Drill 9/64” diameter holes into the icemaker cabinet using the bracket as a template. Use extreme
8. Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in
NOTE: The bin stat must not interfere with the agitator rotation or in the path of ice falling from
the icemaker. If it interferes with the agitator or in the path of ice, bend the bracket out of the way.
Part No. Name Qty.
53003
52969
lid.
with (2) plastic acorn nuts (item 8)
bottom of the slots (see detail A). Use extreme care not to drill into the hopper. Fasten the lid to the
dispenser with four (4) #8 sheet metal screws, two on each side.
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the icemaker
outline so that the icemaker will set on the RTV.
B. Set the icemaker onto the lid and position it as required.
C. Wipe away the excess RTV.
care not to drill into any icemaker components (condenser, tubing, etc.). Secure the brackets using
the screws provided.
the bottom of the ice maker. Wrap the eye of the wireform over the stud near the hole to the end of
the wireform bracket and wrap the tube around the end of the bracket several times, insuring the
tube is secure.
Cover, Gray
Cover, Black
1
Release Date: October 5, 2007 www.cornelius.com Revision: A
© 2007, IMI Cornelius Inc. - 1 - Publication Number: 620204731INS
ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
9. If the plastic acorn nuts interfere with the positioning of the plastic manual fill cover, it may be
necessary to make small notches in the back of the cover to clear the acorn nuts.
10. The unit is now ready for operation.
2 PLACES
2 PLACES
2 PLACES
11
9
8
8
11
9
12
10
12
10
FIGURE 1. ED2XX Kit
Publication Number: 620204731INS - 2 - © 2007, IMI Cornelius Inc.
Loading...