Cooper Wiring Devices RF9601 Users Manual

INSTALLATION INSTRUCTIONS
WARNING:

• Turn OFF circuit breaker or remove fuse(s)

and test that power is off before wiring.

• Never wire any electrical device with power turned on. Wiring

Switch with power on may cause permanent damage to Switch
and void warranty.

• If you are not sure about any part of these

instructions, please contact a licensed
electrician.

IMPORTANT:

RF Switch will not work or will become damaged if wired incorrectly,
and warranty will be voided. Refer to wiring instructions provided on
reverse side.

CAUTION:

1. Use only with 120V AC 60 Hz.

2. Do not exceed maximum rating of the switch as indicated on
the device.

3. Must be installed and used in accordance with
electrical codes.

4. If a bare copper or green ground connection is not

available in the wallbox, contact a licensed electrician
for installation.

5. Use only #14 or #12 copper wire rated for at least

75°C with these devices. Do not use with Aluminum
wire.

NOTES:

1. The RF Master Switch is wired directly to the light fixture.

2. The RF Smart Switch is not compatible with standard 3-

way switches.

3. For Multi-location applications (3-Way or 4-Way) the RF

Smart Accessory Switch (RF9617) or a regular toggle switch
could be used along with one RF Master Switch.

4. The RF Accessory Switch communicates via RF signals to

control the light from more than one location.

5. For multi-location control use RF Smart Dimmer Master

direct wired to the light along with RF Accessory (RF9642-
Z). The RF Accessory does not require direct

connection to the light (use Association function).

Z-Wave Device Network Installation Instructions

1. This product may be added to a new or existing Z-Wave
network. An Eaton Wiring Devices Z-Wave device has a blue
LED, which will blink when the device is not included in a Z-
Wave network. The LED stops blinking when the device is in a
network.

2.To include this device in a Z-Wave network, select the command
on your Z Wave controller for inclusion (Install, Add Device, Add
Node, Include Device, etc.). Then press the device switch one
time to include it in the network.

3.Based on the controller, the controller may ask to scan the QR
code or manually enter 5 digit code under the QR
code to install the device as a secured device

4. After the device is added to the network, the LED
will stop blinking.

5.To exclude this device from a Z-Wave network,
select the command on your Z-Wave controller for exclusion
(Uninstall, Remove Device, Remove Node, Exclude Device, etc.).
Then press the device switch one time to exclude it from the
network. The LED will start blinking.

6. This product works with other Z-Wave products from different
vendors and product categories as part of the same network.

OPERATION INSTRUCTIONS

RF9601 & RF9617

Parameter

Description

Value

1

Delayed Off Time

0 to 255

2

Panic On Time

0 to 255

3

Panic Off Time

0 to 255

5

Power Up State

1=OFF 2= ON
3 = Last State

6

Panic Mode Enable

0=Off
1=On

13

BLUE LED Brightness

Level while the switch

is ON

0-4

14

BLUE LED Brightness

Level while the switch

is OFF

0-4

• Press once to turn lights ON

• Press again to turn lights OFF.

• When lights are ON, press and hold for 2 seconds until the blue

LED blinks. After the preset delay, the lights will turn OFF (up to 4
minutes).

Change LED Indicator brightness
This feature allows the change of the brightness of the
LED indicator.
There are 5 levels (Off to Full brightness) to change the
LED indicator brightness level either while the device is
ON or OFF state.

 Changing the LED indicator brightness when

the device is on ON state

o Turn the light on
o Press and hold the On/Off button for

15 seconds till the LED indicator
flashes for the second time.

o Release the button
o Single tap the ON/OFF button to

change the LED indicator level (it will
cycle between the five levels)

o Once the brightness level is chosen

then double tap on the On/Off button
and this value will be saved

 Changing the LED indicator brightness when

the device is on OFF state

Local Reset
The device could be reset locally which means to be
excluded from its network and restore the default.
Before leaving the network the device will send a
notification to the controller indicating its departure.

 Turn on the device
 Press and hold for 20 second till the LED

flashes

 Release the button
 LED will flash fast and then LED will blink

indicating the switch is not part of the network

o Turn the light Off
o Press and hold the On/Off button for

15 seconds till the LED indicator
flashes.

o Release the button
o Use the dim button (UP/DOWN) to

change the LED indicator level (it will
cycle between the five levels)

o Once the brightness level is chosen

then double tap on the On/Off button
and this value will be saved

Configuration parameters