Constructa SRI3015, CP432J9, 4VN170BA, SRI30E05EU, S4930N1 Installation instructions
...
en
Brief and handy:
everything your dishwasher
needs.
Before using for the first time,
still read the installation and
operating instructions!
Fill with salt
Set the water softening system *
Find out the water hardness
at your water utility company
and enter below
* only before using the
dishwasher for the first
time or if the water hardness changes
Dissolves limescale (not required for set value 0!)
Read off the set value
dH fH Clarke mmol/l
0–6
0–11
0–8
7–11
12–16
17–21
22–35 438–62 27–44
12–16
17–29
30–37
9–11
12–20
21–26
Quickly sorted
Set value on
the appliance
0–1,1
1,2–2,0
2,1–2,9
3,0–3,7
3,0–3,7
3,8–6,2
and then set the value
– Identify setting from the following
0
1
2
3
water hardness table.
– Set the water hardness switch to
the appropriate level.
Summary of instructions for dishwasher
Turn on the tap
Select programme
Rotate programme selector to right only!
Start programme Off we go
Switch on the main switch.
Programme selector rotates in a clockwise
direction and indicates the progress of the
programme.
Switch off the appliance Everything o.k.
When the prgramme has ended (programme selector
is back in the 12 o’clock position), switch off the main
5 600 053 156 (8302) 450R
switch. Turn off the tap.
Fill with rinse aid
Fill with detergent
Switch on the appliance
Unscrew
the lid.
Only before using
the dishwasher
for the first time
pour approx. 1 l /
1 1/4 pt water into
the salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never detergent!)
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1,
lift up lid 2.
Pour in
rinse aid.
Very dirty dishes, a lot of detergent ...
If required, open
the lid (press the
pin).
Warning,
combination
products are not
suitable for all
programmes,
follow manufacturer’s instructions.
Pour in
detergent.
Quick, economical or intensive
Overview of programmes
The max. possible number of programmes is
indicated in this overview. The appropriate
programmes for your appliance can be found
on the fascia.
The programme data is based on laboratory measured values in compliance with
European standard EN 50242. Deviations
are possible in practice.
Duration in minutes
Power consumption in kWh
Water consumption in litres
Intensive Normal Eco Prerinse
117
1,40
22
110
1,30
19
Screw on the
lid. Switch on
dishwasher
immediately.
Close the
lid. CLICK!
Push the lid
shut, press.
PLOP!
65 65 65
99
1,10
16
17
0,12
4
Maintenance and care
For perfect rinsing results
Filters
Check and,
if required,
clean:
Spray arms
Remove blockages/
deposits
Troubleshooting
Fault
Residual water in the appliance
Programme does not continue
Rotate filter cylinder,
remove filter system
Pull up lower arm Unscrew upper arm Clean under running
Rinse under
running water
water (if required, use
a toothpick)
Dealing with problems correctly ...
Possible causes
Programme not yet finished
Programme interrupted
Door is open
Remedial action
Wait until the programme finishes
(programme selector is back in the
12 o’clock position) or cancel programme (see below).
Continue the programme (see
Interrupting the programme).
Close the door, switch on the
main switch again.
Fault Possible causes
Plastic parts/utensil
parts discoloured ...
Milky deposits on the
utensils (removable)
...
Insert Screw on filter
Insert lower arm Screw on upper arm
Detergent with lower bleaching
effect
Insufficient detergent
Rinse aid dosage too high
(visible streaking)
Rinse aid dosage too low
system.
NOTE MARK!
Remedial action
Use detergent containing chlorine
bleach.
Follow manufacturer’s instructions.
Reduce or increase dosage
according to instructions.
Appliance does not run/stops
Utensils are not clean
Sand or gritty residue
on the utensils
No/insufficient water
check whether
Utensils close together/on top of
each other
Insufficient detergent
Unsuitable programme
Spray arms blocked
Filters loose
Filters dirty
Spray arm nozzles blocked
Insufficient water
Turn on the water supply.
Supply fittings unobstructed and
not calcified.
Supply hose kink-free.
Arrange utensils according to
instructions.
Follow manufacturer’s instructions.
Select more intensive programme.
Re-arrange obstacles (e.g. large
spoons).
Clean filters (see above),
attach correctly (MARK).
Clean filters (see above).
Clean spray arms (see above).
See “Appliance does not run”.
Interrupting the programme Cancelling the programme
– Switch off the main switch.
– To continue the programme, switch on the main switch again.
– Switch off the main switch.
– Rotate the programme selector in a clockwise direction to “Dry” and switch on the
main switch again.
– Wait until the Drain programme has finished and the programme selector is back in
the 12 o’clock position.
– Start a new programme or switch off the appliance.
Glasses cloudy/dull ...
Rust on the cutlery ...
Water too hard
Glasses not dishwasher-proof
Detergent unsuitable
Cutlery not rust-resistant
Refill with salt/adjust water softening
system.
Use dishwasher-proof glasses.
Use glass-friendly detergents.
Use dishwasher-proof cutlery.
Further information can be found
in the operating instructions ...
Self-help is worthwhile!
Arrange utensils
correctly
Arrange dishwasher-proof utensils (having removed any ash, wax, grease, ink, sticky labels; remove,
large remnants of jam, dairy products and food) according to the operating instructions and check that
the spray arms can rotate freely.
Loading...