Consew CES-300, CES-300L User Manual

INDUSTRIAL

"ELECTRIC

STEAM

IRON

°

MODELS ·

CES-300
CES-300L

HOW TO USE THE IRON

1.

Hang bottle 1 meter above pressing surface.
(See Bottle Hanging Instruction)

2.

Connect the black hose and to the
clear hose end to the bottle

3.

Empty demineralizer package into the bottle and
fill it

with

tap water only.

use the demmeralizer

4.

T1e

the electnca! cord

5.

Piug the

outlet.

6.

Set the temperature

irdn

7.

Open the bottle valve

with

The

8<

When
supplied iron rest.

9. Always unplug the iron when unattended
or not in use.

1ron

cord into a grounded electncal

heat

up

for

ten

water

by

pressing the steam sw;tch.

1ron

is

now

ready for use.

not pressing, place the

(if

you want

as

an

opt1on.

and

hose together.

d1al

on

NO.

minutes.

and

allow the hose to fill

1ron.

to

i

4 and let the

1ron

on the

and

BOTTLE
CLOSE
OPEN

VALVE

TO

TO

FILL

USE

WATER

GROUNDING

ELECTRIC

TIE

CORD & HOSE

TOGETHER

BOTILE

DEMINERAUZER

"TYPE

PlUG

1MrnR

Do not stand iron

on

its

back.

IMPORTANT NOTICE
ABOUT DEMINERAUZER :

The demineralizer extends the life of

the iron

bule

new package from your distributor.

& prevents calcium build-up.

When

the demineralizer changes from

to

brown, replace it by ordering a

CDNSEIN?

PRESSING WITH CONSEW IRON

Now

that your 1ron

professtonal results.

-Initially,
This may take a few seconds. then you

-

Begtn to press.

-For
It

-There
follows:

-A
starch build-up

-When

to allow water to enter

best results,

is

not necessary to activate the steam switch continuously.

are several setttngs

::i:

2-

1 '

::I

3

~

4

-

#

5

teflon shoe

unattended or not

properly set-up, please read the followmg

s

1

1nto

1t

1s

only necessary to press the steam

on

your temperature

Preheat

-Silk

-Cotton

-Linen(

1s

recommended and

delicate fabrics

and

and

wool(medtum

htgh temperature)

1n

use,

always turn

t1ps

for pressing

the hose and tron, press the steam switch.

will

see

steam.

switch

d1aL

Recommended temperature settings are

(low

temperature)

temperature)

IS

available from your distributor

off

and unplug your iron.

for a

few

seconds

to

prevent garment shine and

with

at

a time.

as

PROBLEM

-

.....

. .. ...

---

Iron does
heat.

No steam
little steam.

Iron spits water.

Iron too

r--·

Iron not

____

not

or

hot.

hot enough.

---

very

----

TROUBLE SHOOTING GUIDE

PROBABLE CAUSE

No power

-------·

Temperature
position
T em perature

or 2.
Little or no water in bottle.

r--------

Bottle not high enough.

Clogged

Clogged

Iron

Steam sw1tch held

Temperature

Temperature

to

iron.

dial IS

dial

..

--

filters.

steam

not hot enough.

IS

holes.

dtal

dtal

"OFF"

in

IS set on No. 1 Set temperature dial

down

IS

set

1s

set

too long.

·----

too high.

-----

too low.

Check electric outlet.
Set temperature dial

No.

No.
Fill bottle
Bottle

Pressing surface.

----

Remove and rinse filter under

water faucet.

Clear holes w1th straightened
paper
Turn temperature dial up(

1----

1---------

SUGGESTED REMEDY

3, 4

or

3, 4 or 5.

-

with

must

·-----------:-------·

clip.

-------------

Let iron heat up.

_____

Release steam
heat up.
Turn thermostat dial
(counter clockwise).

--------

Turn thermostat dial

..

5.

water.

be

-·---·--··

switch

36"

to

to

above the

--------

clockwise).

--·-·

and let

down

up(

clockwise).

--

1ron

IF

THE

ABOVE

CONTACT

YOUR

SCGGESTED

RE~vlEDIES

DISTRIBUTOR

FOR

DO

NOT

FURTHER

CORRECT

INFORI\1ATION.

YOUR

PROBLEM

'