Power over EthernetPassive PoE 24V, for network cable length < 20m (LV version),
DC Power1x DC Jack Connector: 24V (LV version), 48V (HV version)
Power Consumption (Board Only)19W
Operating Voltage3.3V, 5V
Operating SystemCompex OS
CertificationRoHS Compliance
EnvironmentalTemperature: Operating: -20ºC to 70ºC, Storage: -40ºC to 90ºC
Dimensions (W x H x D)117 x 105 x 32 mm
Extras2 x SIM Card Slots (Note2)
Other FeaturesSurge Suppressor
On-board 2x2 5GHz 802.11a/n/ac
4x U.FL connectors
2x Gigabit Ethernet LAN RJ45 Port with Auto MDI-X
1x USB 3.0 Port
1x M.2 (NGFF) “B Key” Socket for 4G Module (Note1)
Note1: The configuration is not applicable for this FCC applicant.
FCC ID: TK4WPJ428
IEEE 802.3af/at or Passive PoE 48V (HV version)
Humidity (non-condensing): Operating: 5% to 95%, Storage: Max. 90%
Note2: The configuration is not applicable for this FCC applicant.
1 x Buzzer
Last Updated: 22/05/2017
RF Performance Table
COMPEX
SYSTEMS
PRELIMINARY
wireless embedded boards
2.4GHz
802.11b
2.4GHz
802.11g
2.4GHz
802.11n/ac
VHT20
2.4GHz
802.11n/ac
VHT40
Data Rate
1Mbps20dBm±2dB
2Mbps20dBm±2dB
5.5Mbps20dBm±2dB
11Mbps20dBm±2dB
6Mbps18dBm±2dB
9Mbps18dBm±2dB
12Mbps18dBm±2dB
18Mbps18dBm±2dB
24Mbps18dBm±2dB
36Mbps17dBm±2dB
48Mbps16dBm±2dB
54Mbps15dBm±2dB
MCS 018dBm21dBm±2dB
MCS 118dBm21dBm±2dB
MCS 218dBm21dBm±2dB
MCS 318dBm21dBm±2dB
MCS 417dBm20dBm±2dB
MCS 516dBm19dBm±2dB
MCS 615dBm18dBm±2dB
MCS 714dBm17dBm±2dB
MCS 813dBm16dBm±2dB
MCS 017dBm20dBm±2dB
MCS 117dBm20dBm±2dB
MCS 217dBm20dBm±2dB
MCS 317dBm20dBm±2dB
MCS 417dBm20dBm±2dB
MCS 516dBm19dBm±2dB
MCS 615dBm18dBm±2dB
MCS 714dBm17dBm±2dB
MCS 813dBm16dBm±2dB
MCS 912dBm15dBm±2dB
TX Power
(per chain)
TX Power
(2 chains)
Tolerance
2.4GHz
802.11b
2.4GHz
802.11g
2.4GHz
802.11n/ac
VHT20
2.4GHz
802.11n/ac
VHT40
Data Rate
1MbpsTBA±2dB
2MbpsTBA±2dB
5.5MbpsTBA±2dB
11MbpsTBA±2dB
6Mbps-94dBm±2dB
9Mbps-93dBm±2dB
12Mbps-92dBm±2dB
18Mbps-90dBm±2dB
24Mbps-87dBm±2dB
36Mbps-85dBm±2dB
48Mbps-81dBm±2dB
54Mbps-77dBm±2dB
MCS 0TBA±2dB
MCS 1TBA±2dB
MCS 2TBA±2dB
MCS 3TBA±2dB
MCS 4TBA±2dB
MCS 5TBA±2dB
MCS 6TBA±2dB
MCS 7TBA±2dB
MCS 8TBA±2dB
MCS 0TBA±2dB
MCS 1TBA±2dB
MCS 2TBA±2dB
MCS 3TBA±2dB
MCS 4TBA±2dB
MCS 5TBA±2dB
MCS 6TBA±2dB
MCS 7TBA±2dB
MCS 8TBA±2dB
MCS 9TBA±2dB
RX Specifications
Sensitivity
Tolerance
2
Atheros and other trademarks are properties of their respective owners. While every effort is made to ensure the information is accurate,
Compex Systems Pte Ltd | www.compex.com.sg | (+65) 6286 2086 | sales@compex.com.sg | Last Updated: 22/05/2017 WH SY HB
Note 1: The device didn’t support beam-forming technology and Cyclic Delay Diversity (CDD)
technology, and the transmit signals are uncorrected, so no add array gain to the band power and
band PSD.
Note 2: For SISO mode, only the Ant 0 chain can transmit. 11a&11b&11g mode support SISO
mode, 11n mode support MIMO mode.
Note 3: When the device working on full band, only the panel antenna (10dBi) can be used.
Panel antenna (25dBi) was used when the device only working on UNII-1 & UNII-3 bands.
Atheros and other trademarks are properties of their respective owners. While every effort is made to ensure the information is accurate,
Compex does not accept liability for any errors or mistakes that may arise. All specifications are subject to change without notice.
Compex Systems Pte Ltd | www.compex.com.sg | (+65) 6286 2086 | sales@compex.com.sg | Last Updated: 22/05/2017 WH SY HB
Federal Communications Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation distance of at least cm from all persons and must
70
not be collocated or operating in conjunction with any other antenna or transmitter.
Caution: This device is only defined as point-to-point product by the manufacturer.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.