Compex Systems WLM54GP23 Users Manual

This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users. For laptop installations, the antenna must be installed to
ensure that the proper spacing is maintained in the event the users places the
device in their lap during use (i.e. positioning of antennas must be placed in the
upper portion of the LCD panel only to ensure 20 cm will be maintained if the user
places the device in their lap for use), and
2) The transmitter module may not be co-located with any other transmitter or
be required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization
is no longer considered valid and the FCC ID can not be used on the final product.
In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling:
This transmitter module is authorized only for use in device where the
antenna may be installed such that 20 cm may be maintained between the
antenna and users (for example access points, routers, wireless ADSL modems,
certain laptop configurations, and similar equipment). The final end product must
be labeled in a visible area with the following:
"Contains TX FCC ID: TK4-WLM54GP23".
Manual Information for End Users
The end user must not have manual instructions to remove or install the
device. The user manual for end users must include the following information in a
prominent location.
"IMPORTANT NOTE:
To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter."
Quick Install Guide
Compex Wireless-AG Mini PCI Adapter
WLM54GP23
1. Introduction
This mini PCI adapter, Compex WLM54GP23 contains a dual-mode single chip MAC/BB/Radio for IEEE 802.11a, 11g and 11b Wireless LAN. It can support high-speed data transmission of up to 54Mbps in the 2.4GHz and 5GHz frequency bands based on 802.11b/g and
802.11a mode respectively.
NETPASSAGE
Version 1.1
Based on the latest industry standard Wi-Fi Certified IEEE
802.11a/b/g specification, the Compex WLM54AG offers maximum channel speeds of up to 54 Mbps. It supports key security features like Wi-Fi Protected Access (WPA), WPA2, WEP and 802.1x.
You can find this adapter that is seated inside the wireless products such as the WLM54GP23. It can be removed from or inserted onto the PCBA of the WLM54GP23.
2. Package Content
Compex WLM54GP23 retail package contains the following items:
1 x Compex WLM54GP23
1 x External Power Adapter
1 x 3dBi SMA Antenna
1 x Base Stand
1 x RJ45 MDIX cross-over Ethernet cable
1 x Quick Install Guide with Warranty Registration Form
1 x Product CD (including Quick Install Guide, User’s Manual,
Firmware Recovery Tool & Utilities)
3. Hardware Installation
1. Connect one end of the RJ45 crossover Ethernet cable to your PC and another end to the Ethernet port of your Compex WLM54GP23.
2. Next, attach the power adapter supplied in the packaging to the power point.
3. Connect the power plug onto the socket on your Compex WLM54GP23.
Power Point
RJ45
Ethernet cable
Compex
W
LM54GP23
4. Power ON your Compex WLM54GP23 and your PC. Notice that the LAN Link/ACT and Power LEDs have lighted up. This indicates that the connection has established successfully between your Compex WLM54GP23
PC
and your PC.
4. Access to Web-based Interface
Compex has developed a powerful uConfig utility which provides you hassle-free access to the web-based configuration page. To do so, simply
1. Insert your Product CD into your CD-ROM drive. Go to
Utilities section and select uConfig to run the program.
2. The following screen shot will appear. Select NetPassage
W
LM54GP23 and click on OpenWeb button to access to the
authentication page.
Now, your Compex WLM54GP23 acts as a DHCP Server which can assign IP address to your PC/clients.
6. WLAN Basic Setup for Compex WLM54GP23
1. To configure your Compex WLM54GP23 for your wireless user, go to WLAN Basic Setup from the CONFIGURATION section.
2. From your Access Point Setup window, key in the ESSID that you intend to use for your wireless network.
3. You may leave the frequency channel as SmartSelect. This allows your access point to select the channel automatically.
4. Leave the remaining settings as default and click Apply button to update the changes.
3. The password is pre-configured as password in the field
provided. Click on Log On! button to access to the main page.
After accessing to the main page of your Compex WLM54GP23, you can start doing your configuration
5. Basic Configuration for Compex WLM54GP23
1. To handle automatic IP addressing, go to Management Port under CONFIGURATION section.
2. Go to DHCP Server option and select Enable radio button. Click on Apply button to update the changes.
7. TCP/IP Configuration for wireless clients
Generally, automatic IP addressing should be configured for your wireless client PCs or notebooks. You may configure the TCP/IP settings of Microsoft windows XP as follows:
1. From your desktop, right click on My Network Places and select Properties.
2. Next, right click on your Ethernet Adapter go to Properties.
3. Highlight Internet Protocol (TCP/IP) and click on Properties button.
4. Select the radio buttons for Obtain an IP address automatically and Obtain DNS server address automatically. Click OK button to update the changes.
7. Next, enter the Network name (SSID) which must be the same
as the ESSID that you input earlier for your access point.
Next, you may set up Windows XP’s Wireless Network Connection as follows:
5. Right click on Wireless
Network Connection
corresponding to the Wireless Ethernet Adapter you wish to connect to your Compex W
LM54GP23 and click on
Properties.
6. Go to Wireless Networks tab and click on Add.. button.
Ensure that the Network name (SSID) value is the same for all wireless clients in the same wireless network.
For now, you may leave the other information as its default settings. Network Authentication: Open Data encryption: Disabled
For details in configuring your Compex the User’s Manual stored in the Product CD.
WLM54GP23, kindly refer to
8. Panel Views and Descriptions
1
2
Disclaimer: Compex, Inc. provides this guide without warranty of any kind, either expressed or implied, including but not limited to the implied warr anties of merchantability and fitness for a particular purpose. Compex, Inc. may make improvements and/or changes to the product and/or specifications of the product described in this guide, without prior notice. Compex, Inc will not be liable for any technical inaccuracies or
5
typographical errors found in this guide. Changes are periodically made to the information contained herein and will be incorporated into later versions of the guide. The information contained is subject to change without prior notice.
Trademark Information: Compex Inc. Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp. NetWare is the
registered trademark of Novell Inc. All other brand and product names are trademarks or registered trademarks of their respective owners. Notice: Copyrights without prior permission of Compex, Inc. is prohibited, except as allowed under the copyright laws.
Manual Revision by Ann
Manual Number: M-0428-V1.2C Version 1.2, April 2005
©
2004 by Compex, Inc. All rights reserved. Reproduction, adaptation, or translation
®
, ReadyLINK® and MicroHub® are registered trademarks of Compex,
3
4
6 7 8 5
Features Status and Indications
1 LAN Link/Act
LED
Steady Yellow Compex
operating at the speed
WLM54GP23 is
of 10Mbps.
Steady Green Compex W
LM54GP23 is
operating at the speed of 100Mbps.
2 WLAN Link/Act
LED
Steady Green More than 1 wireless
client is present in the wireless network.
Blinking Green Activity is detected in
the wireless network.
3 Diagnostic LED Steady Green The device is in access
point or gateway mode. Blinking Green The device is booting. Off The device is in Client
mode.
4 Power LED Steady Blue Power is supplied to the
device. Off No power is supplied to
the device.
5 External Antenna Rotatable antenna 6 LAN RJ45
Using RJ45 Ethernet cable for connection.
Ethernet Port 7 DC 3.3V 3A Power input of 3.3VDC 8 Reset button Push button:
2s to reboot your device between 2s to 10s to restore to its
factory default
> 10s for operating mode switch
This document may become superseded, in which case you may find its latest version at:
http://www.compex.com.sg/prodspec.asp?f=Manual&s=1
POWER
FCC NOTICE: This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.

Connect the computer into an outlet on a circuit different from that to which the
receiver is connected. Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2)
This device must accept any interference received, including interference that may cause undesired
operation. Products that contain a radio transmitter are labeled with FCC ID and may also carry the FCC logo. Caution: Exposure to Radio Frequency Radiation. To comply with the FCC RF exposure compliance requirements, the following antenna installation and device operating configurations must be satisfied: a.b.For configurations using the integral antenna, the separation distance between the antenna(s) and any
person’s body (including hands, wrists, feet and ankles) must be at least 2.5cm (1 inch).
For configurations using an approved external antenna, the separation distance between the antenna and
any person’s body (including hands, wrists, feet and ankles) must be at least 20cm (8 inch). The transmitter shall not be collocated with other transmitters or antennas.
ICES 003 Statement
This Class B digital apparatus complies with Canadian ICES-003.
DECLARATION OF CONFORMITY: Compex, Inc. declares that the product: Product Name: Compex Wireless-A/G Dual-Band Network Access Point Model No.: WPE54AG conforms to the following Product Standards: Radiated Emission Standards:
C63.4-1992; 47 CFR Part 15, Subpart C (Section 15.247), ANSI C63.4-1992.
Conducted Emission Standards:
Immunity Standards:
Low Voltage Directive:
Therefore, this product is in conformity with the following regional st andards: FCC Class B – following the provisions of FCC Part 15 directive; CE Mark – following the provisions of the EC directive.
Manufacturer’s Name: Compex, Inc. Address:840 Columbia Street , Suite B
Brea, CA 92821, USA
---------Cut along the dotted line---- ------Cut along the dotted line----------Cut along the dotted line---------
WAR RANTY REGI S T RA T ION CARD
Register via the Internet at http://www.cpx.com or http://www.compex.com.sg
To activate the warranty, please complete this card and return to Compex within ninety (90) days
Please e-mail this warranty card to support@c ompex.com.sg.
Product: Purchase Date: Model: Serial No:
------ Cut along the dotted line--- --
Name: E- mail:
Company:
Address:
Postal/Zip Code: Country:
Phone: ( )
--- Cut along the dotted line-----
Note:
For purchases within U.S. A and Canada, please fax to Compex, Inc. at (714) 482 0332 For purchases outside U.S.A and Canada, please fax to Compex Sys tems Pte Ltd at (65) 6280-9947
ETSI EN 300 328-2: July 2000; FCC: 47 CFR Part 15, Subpart B, ANSI
ETS 300 826: Nov. 1997.
IEC 801-2; IEC 801-3; IEC 801-4
EN 60 950:1992+A1: 1993+A2: 1993+A3; 1995+A4; 1996+A11: 1997
from the date of purchase.
Increase the separation between the computer and
receiver. Consult the dealer or an experienced ra dio / TV technician for help.
[M-0088-V2.4C]
----Cut along the dotted line----
Loading...