Compex WLM54AG 6A MiniPCI is a high-performance, compact,
lightweight and low power consumption network adapter. Built on
Atheros AR5414 chipset, it can be used for all IEEE802.11 b/g
compatible WLAN and is ideally suited for integration in a wide range o
OEM devices.
WLM54AG 6A MiniPCI network adapter offers an output power of up to
20dBm on b/g band, and also supports a variety of security features such
as WEP, AES,TKIP, receive and transmit filtering, error recovery , quality o
service (QoS) as well as IEEE802.1x standard, thus providing security to
the wireless network and increase WLAN performance.
Features
2.4GHz IEEE 802.11b/g standard
•
Output power of up to 20dBm @ b/g Band
•
Wireless Encryption and Authentication Supported
•
Extended Distances and High Speeds Due to Better Output Signal Power
•
High Performance with Low Power Consumption
•
Multi-Country Roaming Support (IEEE802.11d)
•
Suitable for Embedded System or OEM Project
•
2 x U.FL(Main & Aux) Antenna Connector
•
Affordable and Ideal for a Variety of Applications
•
Technical Specifications
Chipset
Host Interface
Operating
Voltage
Power
Consumption
Antenna
Connector
Standards
Frequency
Range
Modulation
Techniques
Security
Certificate
ROHS
Compliance
Environment
Specifications
Humidity
Dimension
Weight
DataRate TX Power Tolerance DataRateSensitivity
802.11b
Atheros AR5414
PCI Interface v2.3 (Type III-B Mini PCI form factor)
3.3 VDC
1.8W
2 x U.FL Antenna Connector
IEEE 802.11b: 11Mbps 5.5Mbps2Mbps1Mbps
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This device must accept any interference received, including interference that may
cause undesired operation. Product that is a radio transmitter is labeled with FCC ID.
FCC Caution:
(1) Exposure to Radio Frequency Radiation. This equipment must be installed and
operated in accordance with provided instructions and the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be collocated or operating in conjunction with any other
antenna or transmitter. End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions for satisfying RF
exposure compliance.
(2) Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
(3) This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
(4) Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
The equipment must not be co-located or operating in conjunction with any other
antenna or transmitter.
IMPORTANT NOTE: In the event that these conditions cannot be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate
FCC authorization.
OEM integration instructions:
This device is intended only for OEM integrators under the following conditions:
The module is only limited to installation in mobile applications. The antenna must be
installed such that 20 cm is maintained between the antenna and users,and the
transmitter module may not be co-located with any other transmit or antenna. The
module shall be only used with the integral antenna(s) that has been originally tested
and certified with this module.
As long as 3 conditions above are met,further transmitter test will not be required.
However,the OEM integrator is still responsible for testing their end-product for any
additional compliance requirement with this module installed (for example,digital
device emission,PC peripheral requirements,etc.)
End product labeling
This transmitter module is authorization only for use in device where the antenna may
be installed such that 20 cm may be maintained between the antenna and users. The
final end product must be labeled in a visible area with the following:“Contains
Transmitter Module FCC ID: TK4-WLM54AG or Contains FCC ID: TK4-WLM54AG”
Information that must be placed in the end user manual:
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module. The end user manual shall include all required
regulatory information/warning as show in this manual.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.