Compex Systems WLE1216V220 Users Manual
05 November2019
1590 APPLIANCE
R80.20
Getting Started Guide
Models: V-81, V-81W [Classification: Restricted]
Check Point Copyright Notice
Check Point Copyright Notice
© 2019 Check Point Software Technologies Ltd.
All rights reserved. This product and related documentation are protected by copyright and distributed
under licensing restricting their use, copying, distribution, and decompilation. No part of this product or
related documentation may be reproduced in any form or by any means without prior written authorization
of Check Point. While every precaution has been taken in the preparation of this book, Check Point
assumes no responsibility for errors or omissions. This publication and features described herein are
subject to change without notice.
RESTRICTED RIGHTS LEGEND:
Use, duplication, or disclosure by the government is subject to restrictions as set forth in subparagraph (c)
(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and FAR
52.227-19.
TRADEMARKS:
Refer to the Copyright page for a list of our trademarks.
Refer to the Third Party copyright notices for a list of relevant copyrights and third-party licenses.
1590 Appliance R80.20 Getting Started Guide|2
Important Information
Latest Software
We recommend that you install the most recent software release to stay up-to-date with the
latest functional improvements, stability fixes, security enhancements and protection
against new and evolving attacks.
Certifications
For third party independent certification of Check Point products, see the Check Point
Certificationspage.
Check Point R80.20
1590 Appliance R80.20 Getting Started Guide
For more about this release, see the R80.20 home page.
Latest Version of this Document
Open the latest version of this document in a Web browser.
Download the latest version of this document in PDF format.
Feedback
Check Point is engaged in a continuous effort to improve its documentation.
Please help us by sending your comments.
Revision History
Date Description
05 November2019 First release of this document
1590 Appliance R80.20 Getting Started Guide|3
Table of Contents
Table of Contents
Introduction
Shipping Carton Contents
Setting up the Appliance
Wall Mounting
Connecting the Cables
First Time Deployment Options
Appliance Diagrams and Specifications
Front Panel
Back Panel
Side Panels
Using the First Time Configuration Wizard
Starting the First Time Configuration Wizard
Welcome
Zero Touch
6
7
8
8
9
10
11
12
14
16
18
18
19
19
Authentication Details
Appliance Date and Time Settings
Appliance Name
Security Policy Management
Internet Connection
Local Network
Wireless Network
Administrator Access
Appliance Registration
Security Management Server Authentication
Security Management Server Connection
Software Blade Activation
Summary
Zero Touch Cloud Service
21
23
24
25
26
28
30
31
33
36
37
39
40
41
USB Drive or SD Card
Health and Safety Information
42
43
1590 Appliance R80.20 Getting Started Guide|4
Table of Contents
Information sur la Santé et la Sécurité
Support
51
58
1590 Appliance R80.20 Getting Started Guide|5
Introduction
Introduction
Thank you for choosing Check Point's Internet Security Product Suite. Check Point products provide your
business with the most up to date and secure solutions available today.
Check Point also delivers worldwide technical services including educational, professional, and support
services through a network of Authorized Training Centers, Certified Support Partners, and Check Point
technical support personnel to ensure that you get the most out of your security investment.
For more information about the appliance, see the
Guide
.
For more technical information, go to Check Point Support Center.
Check Point 1500 Appliance series Administration
1590 Appliance R80.20 Getting Started Guide|6
Shipping Carton Contents
Introduction
Item
Appliance 1 1590 Appliance appliance
LAN cable 1 1.8m - RJ45 to RJ45, CAT5e, shielded, STP, black color
Console cable 1 1m, USB type-C to USB-2.0 type-A, black color
Power adapter 1 AC to 12VDC desktop, 40W wired, 60W WiFi, black color
Power cord for adapter 1 Plug types: US, UK, EU and AUS/NZ, India, China, Japan
Rubber feet 4 Assembled on the appliance
Wall mount kit 1 Includes drilling hole location sticker.
Antenna 4 WiFi Antenna RP-SMA type, black color (WiFi models only)
Guides 1
License Agreement 1 End user license agreement
Quantity
Description
Screws: M4*6, truss screw
Check Point 1590 Appliance Quick Start Guide
1590 Appliance R80.20 Getting Started Guide|7
Setting up the Appliance
Setting up the Appliance
1.
Remove the Check Point 1590 Appliance appliance from the shipping carton and place it on a
tabletop.
2. Optional - Remove the transparent protective sticker from the front panel of the appliance.
3.
Identify the network interface marked as LAN1. This interface is preconfigured with the IP address
192.168.1.1.
Wall Mounting
To mount the appliance to the wall:
1.
Place the wall-mount sticker on the wall and drill two holes for the screws.
2.
Attach the 2 screws in the accessory kit (M4*6) to the wall.
3.
Mount the appliance and verify the 2 screws are fastened well to the appliance.
Key Item Description
1 Holes on the bottom of the appliance Attach screws here.
1590 Appliance R80.20 Getting Started Guide|8
Connecting the Cables
1.
Connect the power supply unit to the appliance and to a power outlet.
The appliance is turned on when the power supply is connected.
2.
When the appliance is turned on, the Power LED on the front panel lights up in red for a short period.
The LED then turns blue and starts to blink. This shows a boot is in progress and firmware is being
installed.
When the LED turns a solid blue, the appliance is ready for login.
Note - The LED is red if there is an alert or error.
3.
Connect the standard network cable to the LAN1 port on the back panel of the appliance and to the
network adapter on your PC.
4.
Connect the console cable to the console port on the back of the appliance, and to a USB port on a
supported terminal.
Connecting the Cables
a. Set the Flow control to None.
b. To get the console driver, click: https://www.silabs.com/products/development-
tools/software/usb-to-uart-bridge-vcp-drivers
c.
Verify the MD5 and SHA256 are the following:
n MD5 - c0b27c9b0f3a3ed53927a4857853a2cb
n SHA 256 -
5d8fa117cd499a50cab895f35d50d108a61e80b6a3f6d2ecbffa8949085b8f2e
5. If you use an external modem:
Connect the Ethernet cable to the WAN port on the appliance back panel and plug it into your
external modem or router’s PC/LAN network port. The WAN Link LED on the appliance front panel
lights up when the Ethernet is connected
1590 Appliance R80.20 Getting Started Guide|9
First Time Deployment Options
First Time Deployment Options
There are different options for first time deployment of your gateways:
n
"Using the First Time Configuration Wizard" on page18
n
"Zero Touch Cloud Service" on page41
n
"USB Drive or SD Card" on page42"USB Drive or SD Card" on page42
1590 Appliance R80.20 Getting Started Guide|10
First Time Deployment Options
Appliance Diagrams and Specifications
This section describes the different features in the front, back, and side panels of these 1590 Appliance
models:
n Wired
n WiFi (with antennas)
Note - Depending on which model appliance you have, some of the specifications below may vary.
1590 Appliance R80.20 Getting Started Guide|11
First Time Deployment Options
Front Panel
Note - There is only one set of LEDs. These LEDs show different colors (blue or red) depending on what
activity is occurring.
Table: LEDs
Key Item Description
1 WiFi LED
(WiFi models only)
n
Off - WiFi off
n
Blue -WiFi on and operates normally
2 Management LED n
n
Red - WiFi error/alert
Off – No management
n Colors - See below
1590 Appliance R80.20 Getting Started Guide|12
Table: LEDs (continued)
Key Item Description
First Time Deployment Options
3 Internet LED n
4 Power LED (Status) n
Off - No internet connection
n
Blue - Connected
n
Blinking Red - Connection failure
Solid Blue – Normal operation
n
Blinking Blue – Boot in progress or installing
firmware.
n
Red – Error/Alert
Note – This LED is red when the appliance is first turned on.
The Management LED shows the status of the retries mechanism:
Action
Management LED
Activity
Zero Touch is running. Blinks pink (slowly)
Successfully connected to Zero Touch Cloud Server and saved the
Blinks pink (rapidly)
deployment script.
Zero Touch process is completed. SMP activation is not needed. Solid pink
Activation sleeping time. Blinks blue (slowly)
Reactivation. Blinks blue (rapidly)
SMP is connected. Solid blue.
SMP mode is off. LED off
Gateway failed to connect to the SMP and will exit from the retry script. Constant red.
Wait times before retry:
Failure Waiting Time
1st 2 minutes
2nd 4 minutes
3rd 8 minutes
4th 16 minutes
Subsequent Retries every 16 minutes until Cloud Services are successfully activated
1590 Appliance R80.20 Getting Started Guide|13
First Time Deployment Options
The table below describes the network LEDs (RJ45 WAN and LAN ports and the SFP). Each port uses a bicolor LED to reflect the link/activity and speed, from 10M to 1GbE.
RJ45 and 1G SFP LED1 (Green) LED2 (Amber)
No link Off Off
1G link ON ON
1G Act Blink ON
100M link ON Off
100M Act Blink Off
10M link ON Off
10M Act Blink Off
Back Panel
1590 Appliance R80.20 Getting Started Guide|14
First Time Deployment Options
Key Item Description
1 Reset Short press resets the system but does not remove any user parameters.
2 Ground screw Functional grounding.
3 Factory default Press the button continuously for 12 seconds to restore the appliance to its
factory default. All user parameters previously configured are removed.
4 LAN ports LAN ports 1-8.
10/100/1000MbE
5 DMZ fiber SFP
port
DMZ combination port. The LEDs above indicate connection and speed (see
below).
1GbE speed, short and long range.
6 RJ45 DMZ and
WAN1 combo
port
The DMZ is a combo port of SFP and RJ45 (on the right). Only one can
operate a time once plugged in and connected.
10/100/1000MbE
7 USB port 3.0 USB port 3.0 for SW download and external dongle as WiFi.
8 Console Plug in the serial console cable here. Baud rate: 115200.
9 Power cord
Plug the power adapter cord in here.
socket
1590 Appliance R80.20 Getting Started Guide|15
Side Panels
First Time Deployment Options
Key Item Description
1 Anti-theft
slot
2 SD slot Insert micro-SD card here.
Notes:
Insert anti-theft cable here. Use Kensington and Sunbox TL-623M cable as a
reference.
1590 Appliance R80.20 Getting Started Guide|16
First Time Deployment Options
n Micro-SD card supports formats NTFS and FAT, up to 256GB size.
n While inserting the micro-SD card, make sure the golden pins are facing upward:
1590 Appliance R80.20 Getting Started Guide|17
Using the First Time Configuration Wizard
Using the First Time Configuration
Wizard
Configure the Check Point 1590 Appliance appliance with the First Time Configuration Wizard.
To close the wizard and save configured settings, click Quit.
Note - In the First Time Configuration Wizard, you may not see all the pages described in this guide. The
pages that show in the wizard depend on your appliance model and the options you select.
Starting the First Time Configuration Wizard
To configure the Check Point 1590 Appliance appliance for the first time after you complete the hardware
setup, use the First Time Configuration Wizard.
If you do not complete the wizard because of one of these conditions, the wizard will run again the next
time you connect to the appliance:
n The browser window is closed.
n The appliance is restarted while you run the wizard.
After you complete the wizard, you can use the WebUI (Web User Interface) to change settings configured
with the First Time Configuration Wizard and to configure advanced settings.
To open the WebUI, enter one of these addresses in the browser:
n https://my.firewall
n https://192.168.1.1:4434
If a security warning message shows, confirm it and continue.
The First Time Configuration Wizard runs.
1590 Appliance R80.20 Getting Started Guide|18
Loading...