Compex Systems WLE1216V220 User Manual

wireless modules

COMPEX SYSTEMS

PRELIMINARY

4x4 802.11b/g/n Mini PCIe WiFi Module

Standard size form factor

Mod e l: WLE1216V2-2 0

KEY FEATURES

• Qualcomm Atheros ‘Cascade’ QCA9984

• Heat sink allows free air operation

• IEEE 802.11b/g/n compliant, up to 800Mbps

• Mini PCI Express 2.0 interface

• Supports Spatial Multiplexing

Maximal Ratio Combining (MRC), Space Time Block
Code (STBC)

• Supports IEEE 802.11d, e, h, i, j, k, r, u, v time stamp, w ,
and z standards

• Designed for High Bandwidth Enterprise Wireless
Access Points

Specications

Chipset QCA9984

System Memory 256Kbit serial I²C bus EEPROM

Host Interface Mini PCI Express 2.0 Standard

Operating Voltage 3.3V

Antenna Connector 4x U.FL

Frequency Range 2.412 ~ 2.462 GHz

Power Consumption 6.68W (Max)

Supported Operating System CompexWRT or OpenWRT/LEDE

Modulation Techniques CCK, OFDM: BPSK, QPSK, 16-QAM, 64-QAM

Temperature Range Operating: -20ºC to 70ºC

Humidity Operating: 5% to 95% (non-condensing)

Storage: Max. 90% (non-condensing)

ESD Sensitivity Class 1B

Dimensions (W x H x D) 29.9 x 50.8 x 12.9 mm

Storage: -40ºC to 90ºC

Last Updated: 02/01/18

Feature Guide

COMPEX SYSTEMS

PRELIMINARY

U.FL connectors

wireless modules

CH3

CH2

CH1

CH0

Mechanical Dimensions

Mini PCIe 2.0
edge connector

Atheros and other trademarks are properties of their respective owners. While every effor t is made to ensure the information is accurate,

3

Copyright © Compex Systems. All rights reserved. COMPE X and the COMPEX logo, are registered trademarks of Compex Inc.

Compex does not accept liability for any errors or mistakes that may arise. All specifications are subject to change without notice.

Compex Systems Pte Ltd | www.compex.com.sg | ([phone] | [e-mail] | Last Updated: 02/01/18 WH SY HB

Packaging Content

COMPEX SYSTEMS

PRELIMINARY

Item Quantity

WLE1216V2-20 Wireless Module 1

Ordering Conguration

Item Code Chipset Form Factor Card Information

wireless modules

WLE1216V2-207A00001.01 QCA9984 Standard size card

Packaging Information

Packaging Type Dimensions Weight Dimensional Weight

Packing Box (50 units) 385 x 207 x 76 mm 1.514 kg 1.5 kg

Carton Box

(5 packing boxes / 250 units)

422 x 410 x 240 mm 8.3 kg 9 kg

4x4 802.11b/g/n

2.4GHz

Atheros and other trademarks are properties of their respective owners. While every effor t is made to ensure the information is accurate,

4

Copyright © Compex Systems. All rights reserved. COMPE X and the COMPEX logo, are registered trademarks of Compex Inc.

Compex does not accept liability for any errors or mistakes that may arise. All specifications are subject to change without notice.

Compex Systems Pte Ltd | www.compex.com.sg | ([phone] | [e-mail] | Last Updated: 02/01/18 WH SY HB

Compliance Information
FCC 15.105

For a Class B digital device or peripheral, the instructions furnished the user shall
include the following or similar statement, placed in a prominent location in the text of
the manual:
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

FCC 15.19

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.

FCC 15.21

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

FCC 15.203

This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.

RF exposure warning

The antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.

OEM Integration Instructions：

This device is intended only for OEM integrators under the following conditions：
The module is only limited to installation in mobile applications. The antenna must be
installed such that 20 cm is maintained between the antenna and users，and the
transmitter module may not be co-located with any other transmit or antenna. The
module shall be only used with the integral antenna(s) that has been originally tested
and certified with this module.
As long as 3 conditions above are met，further transmitter test will not be required.
However，the OEM integrator is still responsible for testing their end-product for any
additional compliance requirement with this module installed (for example, digital
device emission, PC peripheral requirements，etc.)

IMPORTANT NOTE：
In the event that these conditions cannot be met (for example certain laptop
configuration or co-location with another transmitter), then the FCC authorization for
this module in combination with the host equipment is no longer considered valid and
the FCC ID of the module cannot be used on the final product. In these and
circumstance，the OEM integrator will be responsible for re-evaluating. The end
product (including the transmitter) and obtaining a separate FCC authorization

The final end product must be labeled in a visible area with the following: “Contains
Transmitter Module FCC ID: TK4WLE1216V220 or Contains FCC ID:
TK4WLE1216V220”

The module will be restricted on these host (Detail information show as below)
Manufacturer: Compex Systems Pte Ltd
Product name：Client Terminal
Product Model Number：WPJXXX

Antenna Type Frequency Band

(GHz)

Dipole Antenna

Panel Antenna

2.4 4 5

2.4 4 11

TX Paths Max Peak Gain

(dBi)

Note: The device didn’t support beam-forming technology and Cyclic Delay Diversity (CDD)
technology, and the transmit signals are uncorrected, so no add array gain to the band power and
band PSD.