Quick Install Guide
Compex
16-Port 10/100 Mbps
Fast Ethernet
Desktop Switch
PS2216
Version 1.2
1. Introduction
Figure 1 Compex PS2216
Compex PS2216 – A perfect switch for home and small offices. This is a fast
Ethernet Switch that provides 16 10/100Mbps ports capable of delivering full
or half duplex transmission with flow control. This cost-effective switch
allows the setting of priority ports, trunking groups or VLAN groups. In
addition, PS2216 is designed for full auto negotiation functionality that self
configures for the highest possible operation mode between nodes, coupled
with the collision-free packet switching capability makes this a perfect device
for your expanding network.
2. Panel View
3
11
910
1 2
12 13 14
465
FLW Ctrl
1615
78
Figure 2 Front View of Compex PS2216
Figure 3 Back Panel View of Compex PS2216
Figure 4 Side View of Compex PS2216
3. Panel Descriptions
Indicator Description
1 Power LED ON indicates switch is receiving power.
STEADY AMBER 10M Link
BLINK AMBER 10M Activity
STEADY GREEN 100M Link
2 Port LED
BLINK GREEN 100M Activity
3 16 RJ-45 Ports 16 UTP ports
4 DIP Switch To activate the VLANs, Trunking and Priority ports.
Please refer to Section 6 “Usage of Dip Switch” on the
following page.
5 FLW/Ctrl LED No function assigne d to this LED. This will no t be lighted.
6 DC Power Jack Jack for connection to an external power adapter
ReadyLINK
®
1
2 5
4. Specifications
♦
Industrial Standards Complies with IEEE 802.3 10Base-T, IEEE 802.3u
100Base-TX and ANSI/IEEE 802.3 N-Way autonegotiation standards; FCC Class A; CE mark.
♦
Interface Each unit has 16 10/100Mbps UTP ports (RJ-45).
♦
Port Speed/Mode
Selection
Auto-negotiation
♦
Link Distance 100Base-TX: can support up to 100M of ‘Category 5’
UTP cable to PC, hub or another switch.
10Base-T: can support up to 100M of ‘Category 3, 4,
and 5’ UTP cable to PC, hub or another switch.
♦
LED Indicators LED indicators are provided for status monitoring.
These include LEDs for system power, port speed,
traffic activity and link.
♦
Dyna mic memory
sharing In/Out buffer
4M Bit
♦
Forwarding Method Store-and-Forward.
♦
Number of MAC
Addresses
8K MAC Addresses
♦
Dynamic Addresses
Learning / Filtering
Yes.
♦
Power Supply External 3.3VDC, 3A
♦
Environment
Requirements
Operating Temperature::
Storage Temperature::
Operating Humidity:
Storage Humidity::
(non-condensing)
)
0°C to 40°C
-5°C to 60°C
10% RH to 90% RH
5% to 80% RH
♦
Physical Dimensions 151 x 92x 35mm (L x W x H)
♦
Weight About 0.26 kg
♦
Safety UL, CSA, TUV/GS
5. Installation of Compex PS2216
Compex PS2216 can be installed on a flat surface (desktop) or mounted on a
wall. Follow the steps below for proper installation.
Desktop installation
1. Unpack the switch.
2. Choose a location which is near to the electrical outlet. It is preferable to
place Compex PS2216 on a desktop with clear and sturdy surface.
3. Ensure that there is enough clearance around the unit to allow attachment
of network cables and power adapter.
4. Connect the power adapter to the switch. The POWER LED and the
respective PORT LED should be lighted up.
Wall installation
1. Measure the distance between the mounting holes at the bottom of the
switch and mark the wall to match the location of the mounting holes on
the switch.
2. Drill pilot holes at the two marked locations.
3. Fix two 5/16-inch diameters flat-head mounting screws into the wall,
with the heads of the screws protruded 1/8 inch out from the wall.
4. Carefully set the switch over the screws in the wall; then slide the switch
down onto the screws, pressing it slight to the wall.
5. Connect the power adapter to the switch. The POWER LED and PORT
LED for each connected port should be lighted up.
Now, Compex PS2216 is ready to operate.
6. Usage of DIP switch
Actions Taken Descriptions
Enabled Trunk 1 Port 1,2,9 and 10 are set as Trunking Ports.
Enabled Trunk 2 Port 3, 4,11 and 12 are set as Trunking Ports.
Enabled Priority Port 8 and 16 (High Priority) are set as Priority Ports.
Enabled VLAN VLAN Port 1 will become an overlapping port in Compex
PS2216. The other ports will be separated into 15 individual
VLANs.
For example,
If VLAN DIP Switch is enabled, Port 1 will be able to link to any
of the ports from Port 2 to 16. However, the ports between 2 to 16
will not be a ble to communicate with each other.
Please note that the enabling of VLAN and Port Trunking cannot be set at the
same time.
Disclaimer: Compex, Inc. provides this guide without warranty of any kind, either expressed or implied, including but not
limited to the implied warranties of merchantability and fitness for a particular purpose. Compex, Inc. may make
improvements and/or changes to the product and/or specifications of the product described in this guide, without prior notice.
Compex, Inc will not be liable for any technical inaccuracies or typographical errors found in this guide. Changes are
periodically made to the information contained herein and will be incorporated into later versions of the guide. The
information contained is subject to change without prior notice.
Trademark Information: Compex
®
, ReadyLINK® and MicroHub® are regi stered tra demarks of Compex, Inc. Microsoft
Windows and the Windows logo are the tra demarks of Microsoft Corp. NetWare is the register ed trademark of Nove ll Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Notice: Copyright
©
2003 by Compex, Inc. All rights reserved. Reproduction, adaptation, or translation without prior
permission of Compex, Inc. is prohibited, except as allowed under the copyright laws.
Manual Revision by Ong
Manual Number:
M-0348-V1.2C
Version 1.2, March 2003
FCC NOTICE: This device has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with th e instr uctions, may cause ha rmful in terference t o radio commun ications. However, there i s no guara ntee
that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television
reception, the user is encoura ged to try to correct th e interference by one or mor e of the following measures:
Reorient or r elocate the receivin g antenna.
Connect the computer into an outlet on a circuit
different fr om that to which th e receiver is connected .
Increase the separ ation between the computer and
receiver.
Consult th e dealer or an experien ced radio/T V
technician for help.
Caution:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate th e equipment.
FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)
(2)
This device m ay not cause harmful i nterference, an d
This device m ust accept any inter ference received, inclu ding interferen ce that may cause un desired operation.
ICES 003 Statement
This Class A digital apparatus complies with Canadian ICES-003
Gost NOTE: This device (apparatus, equipment) complies with the radio interference limits established for Class A
equipment in accordance with GOST R 51318.22-99 (CISPR 22-97) and shall not be used in dwelling houses, commercial
and industrial districts with low electric power consumption and be connected to low-voltage distributions electric supply
networks.
DECLARATION OF CONFORMITY: Compex, Inc. declares that the product:
Product Name: Compex 16-Port 10/100 Mbps Fast Ethernet Desktop Switch
Model No.: Compex PS2216 conforms to the following Product Standards:
Radiated Emission Standards:
EN55022A, FCC Part 15 Class A
Conducted Emission Standards:
EN60555Pt2 conducted emission; EN55022A conducted emission, LVD 60950 standard, FCC Part 15 Class A
Immunity Standards:
IEC 801-2; IEC 801-3; IEC 801-4
Low Voltage Directive:
EN 60 950:1992+A1:1993+A2:1993+A3;1995+A4;1996+A11:1997.
Therefore, this product is in conformity with the following regional standards:
FCC Class A followin g the provis ions of
FCC Part 15 directive; CE Mark following the provisions of the EC directive.
Manufactur er’s Name:
Compex, Inc.
Address:
4051 E. La Palma, Unit A,
Anaheim, CA 92807, USA
European Contact:
ReadyLINK Networktechnology GmbH,
Technical Support
Albert Einstein Straβe 34/M21,
63322 Rödermark, Germany
[Fax: +49 (60) 749-0668]
19th March, 2003
_______________
Shi Jia Xiang
R&D Manager
WARRANTY REGISTRATION CARD
[M-0088-V2.3C]
You can register via Internet at: http://www.cpx.com or http://www.compex.com.sg
Or E -mail: support@compex.com.sg with t he following informatio n:
To activate the warranty, please complete this card and return to Compex within ninety (90) days of
purchase date.
Product: Purchase Date: Revision: Serial No:
Name: Tit le: E-ma il:
Company: Dept:
Address: City:
Postal/Zip Code: State: Country:
Phone: ( ) Extn: Fax: ( )
Comp ute r in wh ich th is pro duc t is
insta lled?
Model: Serial No:
TCP/IP IPX/ODI XNS OST DLC DECnet Network protocol
(Check all that
apply):
NDIS SNA NBP Other:
Novell NetWare: 3.X 4.X 5.X SCO Unix: Openserver Ver:
Microsoft Windows: NT4.0 95 98 Win 2000
Linux: Red Hat Ver: SUSe Ver: Others: Ver: .
Network
Operating
System
(Check all that
apply):
Others NOS: Ver: .
Deskto p Publishing Word Pro cessing Accounting
CAD/CAM Spreadsheet Databa se Management
Applications used
on network
processing
(Check all that
apply):
E-ma il Other:
Work Friend Internet Dealer Magazine Exhibition
How did you
learn about
Compex?
Other:
Note:
For purchases within U.S.A and Canada, please fax to Compex, Inc. at (714) 630-6521
For purchases outside U.S.A and Canada, please fax to Compex Systems Pte Ltd at (65) 6280- 9947
----------Cut along the dotted line----------Cut along the dotted line----------Cut along the dotted line---------
--------Cut along the dotted line------------Cut along the dotted line------------Cut along the dotted line------------ Cut along the dotted line-----
Enable
Loading...