Compaq StorageWorks S1000 - NAS, StorageWorks NAS S1000 Install Manual

Part Number: 000001768 Version 1.0

Compaq, the Compaq logo and StorageWorks are trademarks of Compaq Information
Technologies Group, LP.

All other product names mentioned herein may be trademarks of their respective
companies.

Compaq shall not be liable for technical or editorial errors or omissions contained herein.
The information in this document is provided “as is” without warranty of any kind and is
subject to change without notice. The warranties for Compaq products are set forth in the
express limited warranty statements accompanying such products. Nothing herein should
be construed as constituting an additional warranty.

Printed in the U.S.A.

Published by Compaq Computer Corporation under license from Maxtor Corporation.

Copyright© 2001-2002 Maxtor Corporation. All Rights Reserved.

Technical Assistance

Refer to Compaq WorldWide Telephone Numbers booklet for technical support in your
country.

StorageWorks NAS S1000

Table of Contents

Preface: About This Guide .................................................... i

Who Should Use This Guide - - - - - - - - - - - - - - - - - - - - - - - - - - i
Box Contents - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - i
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - i
System Information - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ii
Typographical Conventions - - - - - - - - - - - - - - - - - - - - - - - - - - ii
Related Documents - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ii
Compliance Statements - - - - - - - - - - - - - - - - - - - - - - - - - - - - iii

1 Pre-Installation Planning ............................................................... 1

Equipment Required for Installation- - - - - - - - - - - - - - - - - - - 1
Site Planning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1
About Your StorageWorks NAS S1000 - - - - - - - - - - - - - - - - - 3

2 Installing Your StorageWorks NAS S1000 .................................. 4

Connecting StorageWorks NAS S1000 to Your Network- - - - 4
Turning on the Power- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Installing StorageWorks NAS S1000 Setup and Discovery
Utility Software - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Completing StorageWorks NAS S1000 Setup and Discovery
Utility Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6

3 Configuring Your StorageWorks NAS S1000 ............................. 9

First Login- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
Welcome To StorageWorks NAS S1000
First Time Setup Wizard - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
Setting the Date and Time - - - - - - - - - - - - - - - - - - - - - - - - - 12
Setting the Administrator Password- - - - - - - - - - - - - - - - - - 12
Setting E-mail Alerts- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Setting Server Appliance Identity - - - - - - - - - - - - - - - - - - - - 14
Finish the Wizard - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
Ready for use - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
Normal Power-Down - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17

Index ................................................................................... 18

About This Guide i

About This Guide

Who Should Use This Guide

This Installation Guide is intended to help setup and configure your StorageWorks™
NAS S1000 by Compaq. It assumes that you are somewhat familiar with networking and
system administration basics.

Box Contents

 Compaq StorageWorks NAS S1000 system
 Quick Start Card
 Compaq StorageWorks NAS S1000 End User License Agreement
 Power Cord
 CAT-5 Ethernet Cables (2)
 Mounting ears (pre-installed)
 Rubber feet (4)
 StorageWorksNAS S1000 CD containing:

• StorageWorks NAS S1000 Setup and Discovery Utility

• StorageWorks NAS S1000 documentation

 Worldwide Telephone Numbers booklet
 Limited Warranty Statement
 Important Safety Information book

Overview

Yo ur StorageWorks NAS S1000 comes ready to install with all the required software. It works in
a 10/100 Mbps Ethernet network (or Gigabit Ethernet network when so equipped), and is
administered using an Internet Explorer web browser. It includes

StorageWorks NAS S1000

Setup and Discovery Utility, Compaq’s software utility that helps you locate the unit on your
network, configure

StorageWorks NAS S1000 network settings, and launch the web user

interface.

NOTE: Should you encounter any difficulties during the installation

and configuration process outlined in this guide, please refer
to the On-Line Help File also found on the StorageWorks NAS
S1000 CD.

About This Guide ii

System Information

Please record the following information from the label on the side panel:

 Model Number: __________________________________________
 Serial Number: ___________________________________________
 Assembly Number: ________________________________________

These numbers will be needed by support personnel if you should contact them.

Typographical Conventions

The following typographical conventions are used in this guide to help you locate and
identify information:

Related Documents

Following is a list of related publications for background and additional information:

 StorageWorks NAS S1000 On-Line Help File
 Quick Start Card
 StorageWorks NAS S1000 End User License Agreement (EULA)
 Warranty Statement
 Also see our Web site at: www.compaq.com/storage/nas for the latest Release Notes

Table P-1. Typographical Conventions

Item Symbol Description

Italic text is used for emphasis and book titles.

Bold text identifies menu names, menu options, items you can click

on the screen, and keyboard keys.

Courier
font

identifies file names, folder names, and text
that either appears on the screen or that you
are required to type in.

NOTE: Notes provide extra information, tips, and hints regarding

the topic.

CAUTION: Cautions identify important information about actions

that could result in damage to or loss of data or could
cause the system to behave in unexpected ways.

WAR NI NG : Warnings identify critical information about actions that

could result in unexpected equipment failure, loss of
critical operating system files or potential bodily injury.

About This Guideiii

Compliance Statements

This Class B digital apparatus meets all requirements of the Canadian Interference Causing
Equipment regulations.

Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur la
materiel brouilleur du canada.

This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference that may cause undesired operation.

European Community Compliance Statement

This product is in conformity with the protection requirements of EC Council Directive
89/336/EEC on the approximation of the laws of the Member States relating to
electromagnetic compatibility. Compaq cannot accept responsibility for any failure to
satisfy the protection requirements resulting from a non-recommended modification of
the product.

Korean Government Ministry of Communication (MOC) Statement

Please note that this device has been approved for business purposes with regard to
electromagnetic interference. If you find this is not suitable for your use, you may

exchange it for one with a non-business purpose.

StorageWorks NAS S1000 1

1 Pre-Installation Planning

Equipment Required for Installation

To connect, install and administer your StorageWorks NAS S1000, you will need an
available 10/100 Ethernet network hub or switch port. It will be necessary for your
workstation to have the following capabilities:

• Windows 95/98/Me/NT (SP5)/2000/XP

• Internet Explorer v5.01 or newer - support for Netscape is not currently available.

• Client for Microsoft Networks enabled over TCP/IP

• Ethernet Connection

• DVD/CD-ROM Drive

Site Planning

When planning a site to house your StorageWorks NAS S1000, you will want to consider
requirements for power and network availability, as well as a space with well regulated
temperature and humidity that is relatively free of dust and other airborne contaminants.
If your installation calls for placement on a table top, apply the enclosed rubber feet to the
bottom of the chassis.

The following tables are designed to help you plan your StorageWorks NAS S1000
Installation.

NOTE:

If a secure browser session is necessary, then Internet Explorer
v5.5 with Active X installed is the required browser.

Table 1-1. Size & Weight

Item Quantity

Weight 27 pounds (12.3 kg)

Size 17 x 20 x 1.75 inches (43.2 x 50.8 x 4.5 cm)

NAS S10002

Pre-Installation Planning

Table 1-2. Electrical Requirements

Item Quantity

Voltage Range 90 ~ 135 VAC or 180 ~ 265 VAC

Frequency 47 ~ 63 Hz

WARN ING: Make sure your site has the necessary capacity to

handle your StorageWorks NAS S1000 unit(s).
Overloading electrical supply circuits is extremely
hazardous. Care should also be taken to properly ground
all rack mounted equipment.

Table 1-3. Operating Environment Requirements

Item Quantity

Temperature - Operating

Temperature - Non-Operating

41º to 104º F (5ºC to 40º C)
external operating temperature range

-4º to 140º F (-20ºC to +60ºC)

Humidity - Operating

Humidity - Non-Operating

5% to 85% humidity non-condensing

5% to 95% humidity non-condensing

CAUTION: When mounting your StorageWorks NAS S1000 in a rack system,

make sure that the air vents do not become blocked. Also, care
must be taken to ensure that StorageWorks NAS S1000 is
installed in an environment compatible with the ambient
temperatures stated in the table above. Maximum of 40º C.

StorageWorks NAS S10003

Pre-Installation Planning

About Your StorageWorks NAS S1000

Front Panel

The StorageWorks NAS S1000 front panel has four LEDs. Three are grouped together on the
right side, one on the left. The LEDs indicate the following:

• Far left LED (soft power button). Solid LED indicates power on. This LED will blink
during boot-up, and will also blink to indicate error conditions (See StorageWorks NAS
S1000 On-Line Help File for alert codes).

• Network Link 1 for LAN 1. Flashing indicates network activity.

• Network Link 2 for LAN 2. Flashing indicates network activity.

• Hard disk drive LED indicates read/write activity.

Back Panel

Shown below is the view of the StorageWorks NAS S1000 back panel.

SOFT POWER BUTTON

LAN 1

LAN 2

HARD DISK DRIVE

(FRONT PANEL)

POWER
CONNECTION

FAN

CONNECTIONS FOR FIELD SERVICE PERSONNEL ONLY

UPS
CONNECTION

LAN 1

LAN 2

GIGABIT OPTION

SCSI PORT

(BACK PANEL)

StorageWorks NAS S1000 4

2 Installing Your StorageWorks NAS S1000

Connecting StorageWorks NAS S1000 to Your Network

To connect the StorageWorks NAS S1000 to your network, insert one or both of the
included Ethernet cables into either StorageWorks NAS S1000 10/100 Ethernet port (LAN 1
or LAN 2), located on the rear panel. Insert the other end of this cable into network hub or
switch. If your StorageWorks NAS S1000 is equipped with a Gigabit Ethernet option, you
may connect it to a 10/100/1000 network hub or switch, using a CAT-6 cable (not
supplied).

NOTE: The two 10/100 Ethernet ports found on StorageWorks NAS S1000 are

pre-configured to provide load balancing and fail-over capability.
Although not necessary for a successful installation, this feature does
enhance system performance, and allows for redundancy in the event
of a cable or component failure. To use this function, connect the
second included Ethernet cable to your StorageWorks NAS S1000 and
the other end to another open port on your network hub or switch.
Load balancing and fail-over will automatically be enabled with no
special configuration required for your switch.

LAN 1

LAN 2

StorageWorks NAS S1000 5

Installing Your StorageWorks NAS S1000

Turning on the Power

1 Connect one end of the enclosed power cord to a power source. Plug the other end into the

power receptacle on the back panel shown in the figure below.

2 Toggle the main power switch on the back panel to the “ON” position ( I ).

3 Press the soft power button on the front panel (shown below), to turn on the unit.

The LED in the power button will come on. After a few moments it will begin blinking, and
continue to blink for several minutes during the power-up cycle. When the power light
stops blinking and disk activity stops, your StorageWorks NAS S1000 is ready to configure.

Installing StorageWorks NAS S1000 Setup and Discovery Utility Software

StorageWorks NAS S1000 Setup and Discovery Utility software is Compaq’s software utility
that helps you locate the unit of your network, configure StorageWorks NAS S1000 network
settings, and launch the web user interface.

Use a workstation that is logged onto the network where the StorageWorks NAS S1000
unit is connected. Insert the StorageWorks NAS S1000 Installation and Documentation CD
into your CD-ROM drive. If the initial installation screen does not appear, use Windows
Explorer to launch the setup program from the CD.

Click on StorageWorks NAS S1000 Setup and Discovery Utility to begin your installation.

NOTE:

The “ON” position ( I ) and “OFF” position (O) are displayed on the
main power switch on the back panel.

(BACK PANEL)

POWER
RECEPTACLE

MAIN POWER SWITCH

(FRONT PANEL)

SOFT POWER BUTTON

StorageWorks NAS S1000 6

Installing Your StorageWorks NAS S1000

StorageWorks NAS S1000 Setup and Discovery Utility

When the StorageWorks NAS

S1000 initial installation screen
appears, click the StorageWorks

NAS S1000 Setup and Discovery
Utility link. The utility will guide

you through a typical installation
process.

Completing StorageWorks NAS S1000 Setup and Discovery Utility Installation

When the Install wizard has completed, launch StorageWorks NAS S1000 Setup and
Discovery Utility by clicking on the check box and then selecting Finish.

NOTE: If you have an older version of StorageWorks NAS S1000 Setup and Discovery

Utility on your server, you should un-install the older version, before installing
your newer version.

StorageWorks NAS S1000 7

Installing Your StorageWorks NAS S1000

Alternately, you may exit the wizard without selecting the option by selecting Finish which
will close the InstallShield. Then launch StorageWorks NAS S1000 Setup and Discovery
Utility from your Windows workstation by selecting Start, Programs, StorageWorks NAS
S1000 Setup and Discovery Utility.

Finding Your New StorageWorks NAS S1000

Once StorageWorks NAS S1000 Setup and Discovery Utility finds all of the StorageWorks
NAS S1000 units on your network, it will display computer Name, Status, IP Address and
Workgroup.

If you have earlier StorageWorks NAS S1000 version models on your network, they will be
displayed as well, and you may continue to administer those units through this
StorageWorks NAS S1000 Setup and Discovery Utility session.

NOTE: If you launch StorageWorks NAS S1000 Setup and Discovery Utility from the

InstallShield, the InstallShield will remain running in the background. You may
wait until completion of your configuration (next chapter) to finish and exit the
InstallShield, or you may minimize all other applications and finish and exit at
this time.

NOTE:

If you have multiple units in a rack-mounted situation, highlight the
appropriate unit on the StorageWorks NAS S1000 Setup and Discovery Utility.
The front LED will blink eight times to help you locate it.

StorageWorks NAS S1000 8

Installing Your StorageWorks NAS S1000

If a DHCP server is running in your network, launch the StorageWorks NAS S1000
configuration screens by double-clicking on the default name of your newly installed
StorageWorks NAS S1000 and skip to Chapter 3.

Modifying Default Network Settings for non-DHCP Service

If StorageWorks NAS S1000 is attached to a network without a DHCP server, your
StorageWorks NAS S1000 will be displayed with an IP Address in the 169.254.xxx.xxx

range. You must now assign a unique “Static IP Address” to your unit. See your network
administrator for an available IP address before proceeding.

To set an IP address, highlight the default name of your StorageWorks NAS S1000 with a
single mouse click and then select the Change Settings button. You will receive a warning
message about making changes - click OK. Change the DHCP Client setting by clicking the
down arrow and highlighting Disabled.

Then Delete the default IP Address and
enter your unique address, subnet
mask, and gateway (if applicable.)

Next, click Apply to make the changes
permanent. Your StorageWorks NAS
S1000 will now automatically reboot.

End this procedure by selecting the
Close button.

After your StorageWorks NAS S1000 has
rebooted, press the Refresh button in
the main StorageWorks NAS S1000
Setup and Discovery Utility window.
When the search is complete, your new
settings should appear. If not, go back
to the top of this page, and begin again.

Now, double click on the StorageWorks
NAS S1000 in the StorageWorks NAS
S1000 Setup and Discovery Utility
window to launch the configuration
screens on your newly enabled
StorageWorks NAS S1000.

CAUTION: You are reminded that currently, there is no Netscape browser support. If you

are using Netscape as your default browser, you will have to reset Internet
Explorer as your default browser before beginning this installation.

StorageWorks NAS S1000 9

3 Configuring Your StorageWorks NAS S1000

First Login

To begin configuring your StorageWorks NAS S1000, you must now login by entering
Administrator into the User Name field. Leave the Password field and Domain field blank
and click OK.

After finishing login, then Internet Explorer browser will launch and display the HTTP
Shares window. Click on Administer this server appliance.

StorageWorks NAS S1000 10

Configuring Your StorageWorks NAS S1000

Security Alert

The Security Alert dialog box appears, asking if you want to proceed with the security
certificate.

To install the certificate, select View Certificate button, then select Install Certificate button.

Click the Next button, and you will be guided through the Certificate Manager Import Wizard.

NOTE: If you select the NO button, it will end the Security Alert dialog

box, and you will not be able to proceed.
If you select the YES button and do not install the certificate,
then this Security Alert message box will be activated each
time login occurs!

StorageWorks NAS S1000 11

Configuring Your StorageWorks NAS S1000

Once added to the Root Store, you will no longer be prompted for the Security Certificate at
login.

Next, you will be prompted for a second login to gain access to the StorageWorks NAS
S1000 Configuration Wizard. Login by entering Administrator into the User Name
field. Leave the Password field and Domain field blank and click OK.

Welcome To StorageWorks NAS S1000 First Time Setup Wizard

The first-time setup wizard provides a quick way to input the necessary settings in getting
your StorageWorks NAS S1000 system up and running. This setup wizard WILL ONLY appear
the first time you logon to your StorageWorks NAS S1000.

The setup wizard takes you through the first five necessary steps in configuring your
system:

Setting the date and time
Setting the Administrator password
Setting E-mail alerts
Setting server appliance identity
Finish the wizard

After this first session, you can modify any of these parameters by using the configuration
options under the Network tab (Setting the Administrator Password and Setting the Server
Appliance Identity) and the Maintenance tab (Setting the Date and Time and Setting
E-Mail Alerts) in the primary navigation bar.

NOTE:

If you change the name of your StorageWorks NAS S1000
during the Setup and Configuration phase, you will be
required to re-install the security certificate.

StorageWorks NAS S1000 12

Configuring Your StorageWorks NAS S1000

Setting the Date and Time

Enter the year, month, date, hour, and time (hours, minutes, AM/PM) and your time zone
for your StorageWorks NAS S1000. Optionally, you can also have the server automatically
adjust your server's time for daylight saving time changes.

The changes you make to your StorageWorks NAS S1000 will not affect the settings on your
desktop client workstation.

Click on NEXT to move to the next step in the setup wizard.

Setting the Administrator Password

The Administrator Account page prompts you for the:

 The current password (blank for first time setup)
 The new password, and
 Confirmation of the new password.

The grayed-out Administrator user name is automatically retrieved from the system.

Click on NEXT to move to the next step in the setup wizard.

StorageWorks NAS S1000 13

Configuring Your StorageWorks NAS S1000

Setting E-mail Alerts

The Set Alert E-Mail page allows you to either enable or disable sending alert e-mails. Alert
e-mails are defined as:

 Critical alerts - these alerts could result in system malfunction or failure unless cleared.
 Warning alerts - these alerts describe abnormal system operation that should be fixed

as soon as possible.

 Informational alerts - these alerts provide the administrator with recent normal

changes in system status.

If enabled, you can decide which alert levels you want sent to the administrators. You may
select none, one, two, or all options:

 Send critical alert e-mail
 Send warning alert e-mail
 Send informational alert e-mail

To complete sending an alert E-mail, input the Administrator's E-mail address and the fully
qualified domain name of the SMTP server or IP address of their E-mail server.

Click on NEXT to move to the next step in the setup wizard.

StorageWorks NAS S1000 14

Configuring Your StorageWorks NAS S1000

Setting Server Appliance Identity

Use this wizard step to fully identify your unit by entering the following information:

 Server appliance name
 DNS suffix (if required)
 If the server appliance is a member of a workgroup or domain
 The name or the workgroup or domain
 If the server is a domain server, enter the name and password of the user with Admin

rights, to allow them to join the domain.

Click on NEXT to finish the wizard.

StorageWorks NAS S1000 15

Configuring Your StorageWorks NAS S1000

Finish the Wizard

If you DID NOT change the server appliance name (host name), the DNS suffix, the
workgroup or domain membership, nor the workgroup or domain name, a Setup Wizard
Finish window appears.

Click on the Finish button to exit the wizard and return to the Web UI. A restart WILL NOT
be required.

However, if you DID change either the server appliance name (host name), the DNS suffix,
the workgroup or domain membership, and/or the workgroup or domain name during the
initial setup, a Restart Server Appliance window appears.

Click on the Finish button to exit the wizard and to automatically initiate a restart to make
the changes effective.

StorageWorks NAS S1000 16

Configuring Your StorageWorks NAS S1000

Ready for use

Once configured, your StorageWorks NAS S1000 is now ready for use. From your
workstation on the StorageWorks NAS S1000 Setup and Discovery Utility window, select
Refresh button. Then highlight and double click the name of your StorageWorks NAS S1000
unit in the StorageWorks NAS S1000 Setup and Discovery Utility window.

When you have completed the login sequence described on page 1, you will be greeted by
the Welcome page and may begin using your StorageWorks NAS S1000.

For further information on adding users and groups, creating shares or other system
modifications and configurations for your StorageWorks NAS S1000 unit, you may refer to
the On-Line Help File in the Web UI. For your convenience, the help files are also located on
the StorageWorks NAS S1000 Installation and Documentation CD, and can be accessed
directly from “Help” on the Welcome screen.

StorageWorks NAS S1000 17

Configuring Your StorageWorks NAS S1000

Normal Power-Down

To power-down your StorageWorks NAS S1000 under normal conditions, you may use the
web interface, by selecting Maintenance on the menu bar, and then Shutdown, or you may
use the soft power button on the front panel.

After shutdown, to terminate power to all integrated components of StorageWorks NAS
S1000, switch off the main power switch on the back panel.

18

Index

B

Back panel 3

C

Configuring your StorageWorks
NAS S1000 9

D

Date and Time

setting 12

Default network settings

modifying 8

DHCP server 8

network without 8
DNS suffix 14
Domain 9, 11, 14, 15

E

Electrical Requirements 2
E-mail Alerts

setting 13
Ethernet 4

Ethernet cables i, 4
Ethernet Connection 1
Ethernet network i
Ethernet network hub 1
Ethernet ports 4

F

Fail-over 4
First Time Setup Wizard 11
Front panel 3

G

Gigabit Ethernet network i
Gigabit Ethernet option 4

H

Hard disk drive LED 3
HTTP Shares 9
Humidity 1

I

Install Certificate 10
Installing StorageWorks NAS S1000 4
Internet Explorer i, 1, 8, 9

L

LEDs 3
Load balancing 4
Login 9, 11

M

Main power switch 5

N

Netscape 1
Netscape browser support 8
Network activity indicator 7
Network connection 4
Network hub 4

O

Operating environment requirements 2

P

Password 9, 11
Password setting 12
Power

turning on 5

Power on indicator 3
Power-down 17

R

Ready for use 16
Release notes ii

S

Security Alert 10
Server Appliance Identity

setting 14
Shutdown 17
Site planning 1
Size & Weight Requirements 1

Soft power button 3, 5, 17
Software CD i
StorageWorks NAS S1000

configuring 9

finding on network 7
StorageWorks NAS S1000 Setup and

Discovery Utility i, 5, 6, 16

19

T

Table top installation 1
Temperature 2

V

View Certificate 10

W

Web site ii
Workgroup 7, 14