Compaq MSB900L, MSB900 User Manual

Detailed Technical USER MANUAL FOR:

3.5”-SBC

MSB900/L

Nordstrasse 11/F CH- 4542 Luterbach Tel.: ++41 (0)32 681 58 00 Fax: ++41 (0)32 681 58 01 Email: support@digitallogic.com Homepage:

http://www.digitallogic.com

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

For internal use only:

File: MSB900_Detailed_V1.0 Path: R:\HANDBUCH\MSB\MSB900\MSB900_Detailed_V1.0.doc

This publication is protected by copyright and all rights are reserved. No part of this document may be reproduced, transmitted, transcribed or stored in a retrieval system, in any form or by any means, electronic, mechanical, optical, manual, or otherwise, without the prior written permission of DIGITAL-LOGIC AG.

The software described herein, together with this document, are furnished under a license agreement and may be used or copied only in accordance with the terms of that agreement.

About this Manual and How to Use It

This manual is written for the original equipment manufacturer (OEM) who plans to build computer systems based on the single board MICROSPACE-PC. It is for integrators and programmers of systems based on the MICROSPACE-Computer family. This manual provides instructions for installing and configuring the board, and describes the system and setup requirements. This document contains information on hardware requirements, interconnections, and details of how to program the system. Please check the Product CD for further information and manuals.

REVISION HISTORY:

Document Version

V1.0 02.2008 DAR Initial document

Date/Initials:

Modification: Remarks, News, Attention:

Attention!

1. All information in this manual, and the product, are subject to change without prior notice.

2. Read this manual prior to installation of the product.

3. Read the security information carefully prior to installation of the product.

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

Table of Contents

1. Preface.......................................................................................................................5

1.1. Trademarks ................................................................................................................... 5

1.2. Disclaimer ..................................................................................................................... 5

1.3. Environmental Protection Statement .......................................................................... 5

1.4. Who should use this Product....................................................................................... 5

1.5. Recycling Information .................................................................................................. 6

1.6. Technical Support......................................................................................................... 6

1.7. Limited Two Year Warranty.......................................................................................... 6

1.8. Explanation of Symbols ............................................................................................... 7

1.9. Applicable Documents and Standards........................................................................ 8

1.10. For Your Safety ............................................................................................................. 9

1.11. RoHS Commitment ....................................................................................................... 9

1.11.1. RoHS Compatible Product Design ......................................................................................... 10

1.11.2. RoHS Compliant Production Process .................................................................................... 10

1.11.3. WEEE Application .................................................................................................................. 10

1.12. Swiss Quality .............................................................................................................. 11

1.13. The Swiss Association for Quality and Management Systems ............................... 11

2. Overview..................................................................................................................12

2.1. Standard Features of the MSB900/L.......................................................................... 12

2.2. Unique Features.......................................................................................................... 12

2.3. MSB900 Block Diagram.............................................................................................. 13

2.4. MSB900/MSB900L specifications .............................................................................. 14

2.5. Examples of Ordering Codes..................................................................................... 16

2.6. Related Application Notes.......................................................................................... 16

2.7. Dimensions & Diagrams............................................................................................. 17

2.7.1. MSB900/L .................................................................................................................................. 17

2.7.2. MSB800CON Part Nr 802205.................................................................................................... 21

2.8. MSB900/L Incompatibilities to a standard PC/AT..................................................... 22

2.9. Related Application Notes.......................................................................................... 22

2.10. High Frequency Radiation (to meet EN55022) .......................................................... 22

2.11. Battery-Lifetime .......................................................................................................... 23

2.11.1. External battery assembling (for the MSB900L): ................................................................... 23

3. Bus Signals .............................................................................................................23

3.1. Addressing PCI Devices............................................................................................. 23

3.1.1. MSB900 and MSB900L ............................................................................................................. 23

4. BIOS History............................................................................................................24

5. Detailed System Description .................................................................................25

5.1. Power Requirements .................................................................................................. 25

5.2. Boot Time .................................................................................................................... 25

5.3. CPU, Boards and RAMs.............................................................................................. 26

5.3.1. CPUs of this MICROSPACE Product ........................................................................................ 26

5.3.2. Numeric Coprocessor ................................................................................................................ 26

5.3.3. DDRAM Memory........................................................................................................................ 26

5.4. Interfaces..................................................................................................................... 26

5.4.1. Keyboard AT compatible and PS/2 Mouse................................................................................ 26

5.4.2. Line Printer Port LPT1 ............................................................................................................... 26

5.4.3. Serial Ports COM1-COM2 ......................................................................................................... 27

5.4.4. Floppy Disk Interface ................................................................................................................. 27

5.5. Controllers................................................................................................................... 27

5.5.1. Interrupt Controllers ................................................................................................................... 27

5.6. Timers and Counters.................................................................................................. 28

5.6.1. Programmable Timers ............................................................................................................... 28

5.6.2. RTC (Real Time Clock).............................................................................................................. 28

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

5.6.3. Watchdog................................................................................................................................... 28

5.6.4. ROM-BIOS Sockets................................................................................................................... 28

5.6.5. BIOS CMOS Setup .................................................................................................................... 29

5.7. CMOS RAM Map.......................................................................................................... 29

5.8. EEPROM saved CMOS Setup..................................................................................... 34

5.8.1. EEPROM Memory for Setup...................................................................................................... 35

5.9. Memory & I/O Map....................................................................................................... 35

5.9.1. System Memory Map ................................................................................................................. 35

5.9.2. System I/O map ......................................................................................................................... 36

6. VGA ..........................................................................................................................40

6.1. VGA/LCD Controller of the Geode LX900.................................................................. 40

6.2. Graphic Modes............................................................................................................ 40

7. Video Input ..............................................................................................................41

8. Description of the connectors ...............................................................................41

9. Jumper Locations on the Board ............................................................................53

9.1. The Jumpers on MSB900/L ........................................................................................ 53

9.2. Reload Default BIOS Settings .................................................................................... 53

10. Cable Interfaces ......................................................................................................55

10.1. The Hard Disk Cable 44pin......................................................................................... 55

10.2. The COM1/LPT Serial Interface Cable ....................................................................... 56

10.3. The COM2 Serial Interface Cable............................................................................... 57

11. Thermal Specifications...........................................................................................58

11.1. Thermal Analysis for Case Integration...................................................................... 58

12. Assembly Views......................................................................................................59

12.1. MSB900/L .................................................................................................................... 59

12.2. Mechanical Dimensions ............................................................................................. 61

13. PXE-Boot and PXE-Setup in the BIOS ..................................................................62

14. PXE-License Order .................................................................................................64

15. Index ........................................................................................................................65

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

1. PREFACE

The information contained in this manual has been carefully checked and is believed to be accurate; it is subject to change without notice. Product advances mean that some specifications may have changed. DIGITAL-LOGIC AG assumes no responsibility for any inaccuracies, or the consequences thereof, that may appear in this manual. Furthermore, DIGITAL-LOGIC AG does not accept any liability arising from the use or application of any circuit or product described herein.

1.1. Trademarks

DIGITAL-LOGIC, DIGITAL-LOGIC-Logo, MICROSPACE, and smartModule are registered trademarks owned worldwide by DIGITAL-LOGIC AG, Luterbach (Switzerland). In addition, this document may include names, company logos, and registered trademarks which are, therefore, proprietary to their respective owners.

1.2. Disclaimer

DIGITAL-LOGIC AG makes no representations or warranties with respect to the contents of this manual, and specifically disclaims any implied warranty of merchantability or fitness, for any particular purpose. DIGITALLOGIC AG shall, under no circumstances, be liable for incidental or consequential damages or related expenses resulting from the use of this product, even if it has been notified of the possibility of such damage.

1.3. Environmental Protection Statement

This product has been manufactured to satisfy environmental protection requirements wherever possible. Many of the components used (structural parts, printed circuit boards, connectors, batteries, etc.) are capable of being recycled. Final disposal of this product after its service life must be accomplished in accordance with applicable country, state, or local laws or regulations.

1.4. Who should use this Product

 Electrical engineers with know-how in PC-technology.

 Because of the complexity and the variability of PC-technology, we cannot guarantee that the product

will work in any particular situation or set-up. Our technical support will try to help you find a solution.

 Pay attention to electrostatic discharges; use a CMOS protected workplace.

 Power supply must be OFF when working on the board or connecting any cables or devices.

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

1.5. Recycling Information

All components within this product fulfill the requirements of the RoHS (Restriction of Hazardous Substances Directive). The product is soldered with a lead free process.

1.6. Technical Support

1. Contact your local DIGITAL-LOGIC Technical Support, in your country.

2. Use the Internet Support Request form at http://support.digitallogic.ch/  embedded products  New Support Request

Support requests are only accepted with detailed information about the product (i.e., BIOS-, Boardversion)!

1.7. Limited Two Year Warranty

DIGITAL-LOGIC AG guarantees the hardware and software products it manufactures and produces to be free from defects in materials and workmanship for two years following the date of shipment from DIGITALLOGIC AG, Switzerland. This warranty is limited to the original purchaser of the product and is not transferable.

During the two year warranty period, DIGITAL-LOGIC AG will repair or replace, at its discretion, any defective product or part at no additional charge, provided that the product is returned, shipping prepaid, to DIGITAL-LOGIC AG. All replaced parts and products become property of DIGITAL-LOGIC AG.

Before returning any product for repair, direct customers of DIGITAL-LOGIC AG, Switzerland are re-

quired to register a RMA (Return Material Authorization) number in the Support Center at

http://support.digitallogic.ch/

All other customers must contact their local distributors for returning defective materials.

This limited warranty does not extend to any product which has been damaged as a result of accident, misuse, abuse (such as use of incorrect input voltages, wrong cabling, wrong polarity, improper or insufficient ventilation, failure to follow the operating instructions that are provided by DIGITAL-LOGIC AG or other contingencies beyond the control of DIGITAL-LOGIC AG), wrong connection, wrong information or as a result of service or modification by anyone other than DIGITAL-LOGIC AG. Nor if the user has insufficient knowledge of these technologies or has not consulted the product manuals or the technical support of DIGITAL-LOGIC AG and therefore the product has been damaged.

Empty batteries (external and onboard), as well as all other battery failures, are not covered by this manufacturer’s limited warranty.

Except, as directly set forth above, no other warranties are expressed or implied, including, but not limited to, any implied warranty of merchantability and fitness for a particular purpose, and DIGITAL-LOGIC AG expressly disclaims all warranties not stated herein. Under no circumstances will DIGITAL-LOGIC AG be liable to the purchaser or any user for any damage, including any incidental or consequential damage, expenses, lost profits, lost savings, or other damages arising out of the use or inability to use the product.

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

1.8. Explanation of Symbols

CE Conformity

This symbol indicates that the product described in this manual is in compliance with all applied CE standards.

Caution, Electric Shock!

This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them. Failure to observe the precautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your equipment.

Caution, Electric Shock!

This symbol and title warn of hazards due to electrical shocks (> 32V) when touching products or parts of them. Failure to observe the precautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your equipment

Warning, ESD Sensitive Device!

This symbol and title inform that electronic boards and their components are sensitive to Electro Static Discharge (ESD). In order to ensure product integrity at all times, care must always be taken while handling and examining this product.

Attention!

This symbol and title emphasize points which, if not fully understood and taken into consideration by the reader, may endanger your health and/or result in damage to your equipment.

Note...

This symbol and title emphasize aspects the user should read through carefully for his, or her, own advantage.

Warning, Heat Sensitive Device!

This symbol indicates a heat sensitive component.

Safety Instructions

This symbol shows safety instructions for the operator to follow.

This symbol warns of general hazards from mechanical, electrical, and/or chemical failure. This may endanger your life/health and/or result in damage to your equipment.

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

1.9. Applicable Documents and Standards

The following publications are used in conjunction with this manual. When any of the referenced specifications are superseded by an approved revision, that revision shall apply. All documents may be obtained from their respective organizations.

 Advanced Configuration and Power Interface Specification Revision 2.0c, August 25, 2003 Copyright

 ANSI/TIA/EIA-644-A-2001: Electrical Characteristics of Low Voltage Differential Signaling (LVDS) In-

terface Circuits, January 1, 2001. http://www.ansi.org/

 ANSI INCITS 361-2002: AT Attachment with Packet Interface - 6 (ATA/ATAPI-6), November 1, 2002.

http://www.ansi.org/

 ANSI INCITS 376-2003: American National Standard for Information Technology – Serial Attached

SCSI (SAS), October 30, 2003. http://www.ansi.org/

reserved. http://www.intel.com/labs/media/audio/

 Display Data Channel Command Interface (DDC/CI) Standard (formerly DDC2Bi) Version 1, August

http://www.vesa.org/summary/sumddcci.htm

http://www.expresscard.org/

 IEEE 802.3-2002, IEEE Standard for Information technology, Telecommunications and information ex-

change between systems–Local and metropolitan area networks–Specific requirements – Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications. http://www.ieee.org

 IEEE 802.3ae (Amendment to IEEE 802.3-2002), Part 3: Carrier Sense Multiple Access with Collision

Detection (CSMA/CD) Access Method and Physical Layer Specifications, Amendment: Media Access Control (MAC) Parameters, Physical Layers, and Management Parameters for 10 GB/s Operation.

http://www.ieee.org

 PICMG® Policies and Procedures for Specification Development, Revision 2.0, September 14, 2004,

PCI Industrial Computer Manufacturers Group (PICMG®), 401 Edgewater Place, Suite 500, Wakefield, MA 01880, USA, Tel: 781.224.1100, Fax: 781.224.1239. http://www.picmg.org/

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

 Smart Battery Data Specification Revision 1.1, December 11, 1998. www.sbs-forum.org

1998, 2000 Duracell, Inc., Energizer Power Systems, Inc., Fujitsu, Ltd., Intel Corporation, Linear Technology Inc., Maxim Integrated Products, Mitsubishi Electric Semiconductor Company, PowerSmart, Inc., Toshiba Battery Co. Ltd., Unitrode Corporation, USAR Systems, Inc. All rights reserved.

http://www.smbus.org/

1.10. For Your Safety

Your new DIGITAL-LOGIC product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long, fault-free life. However, this life expectancy can be drastically reduced by improper treatment during unpacking and installation. Therefore, in the interest of your own safety and for the correct operation of your new DIGITAL-LOGIC product, please comply with the following guidelines.

Attention!

All work on this device must only be carried out by sufficiently skilled personnel.

Caution, Electric Shock!

Before installing your new DIGITAL-LOGIC product, always ensure that your mains power is switched off. This applies also to the installation of piggybacks or peripherals. Serious electrical shock hazards can exist during all installation, repair and maintenance operations with this product. Therefore, always unplug the power cable and any other cables which provide external voltage before performing work.

Warning, ESD Sensitive Device!

Electronic boards and their components are sensitive to static electricity. In order to ensure product integrity at all times, be careful during all handling and examinations of this product.

1.11. RoHS Commitment

DIGITAL-LOGIC AG is committed to develop and produce environmentally friendly products according to the Restriction of Hazardous Substances (RoHS) Directive (2002/95/EC) and the Waste Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) established by the European Union. The RoHS directive was adopted in February 2003 by the European Union and came into effect on July 1, 2006. It is not a law but a directive, which restricts the use of six hazardous materials in the manufacturing of various types of electronic and electrical equipment. It is closely linked with the Waste Electrical and Electronic Equipment Directive (WEEE) 2002/96/EC, which has set targets for collection, recycling and recovery of electrical goods and is part of a legislative initiative to solve the problem of huge amounts of toxic e-waste.

Each European Union member state is adopting its own enforcement and implementation policies using the directive as a guide. Therefore, there could be as many different versions of the law as there are states in the EU. Additionally, non-EU countries like China, Japan, or states in the U.S. such as California may have their own regulations for green products, which are similar, but not identical, to the RoHS directive.

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

RoHS is often referred to as the "lead-free" directive but it restricts the use of the following substances:

 Lead

 Mercury

 Cadmium

 Chromium VI

 PBB and PBDE

The maximum allowable concentration of any of the above mentioned substances is 0.1% (except for Cadmium, which is limited to 0.01%) by weight of homogeneous material. This means that the limits do not apply to the weight of the finished product, or even to a component but to any single substance that could (theoretically) be separated mechanically.

1.11.1. RoHS Compatible Product Design

All DIGITAL-LOGIC standard products comply with RoHS legislation.

Since July 1, 2006, there has been a strict adherence to the use of RoHS compliant electronic and mechanical components during the design-in phase of all DIGITAL-LOGIC standard products.

1.11.2. RoHS Compliant Production Process

DIGITAL-LOGIC selects external suppliers that are capable of producing RoHS compliant devices. These capabilities are verified by:

1. A confirmation from the supplier indicating that their production processes and resulting devices are

RoHS compliant.

2. If there is any doubt of the RoHS compliancy, the concentration of the previously mentioned sub-

stances in a produced device will be measured. These measurements are carried out by an accredited laboratory.

1.11.3. WEEE Application

The WEEE directive is closely related to the RoHS directive and applies to the following devices:

 Large and small household appliances  IT equipment  Telecommunications equipment (although infrastructure equipment is exempt in some countries)  Consumer equipment  Lighting equipment – including light bulbs  Electronic and electrical tools  Toys, leisure and sports equipment  Automatic dispensers

It does not apply to fixed industrial plants and tools. The compliance is the responsibility of the company that brings the product to market, as defined in the directive. Components and sub-assemblies are not subject to product compliance. In other words, since DIGITAL-LOGIC does not deliver ready-made products to end users the WEEE directive is not applicable for DIGITAL-LOGIC. Users are nevertheless encouraged to properly recycle all electronic products that have reached the end of their life cycle.

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

1.12. Swiss Quality

 100% Made in Switzerland

 DIGITAL-LOGIC is a member of "Swiss-Label"

 This product was not manufactured by employees earning

piecework wages

 This product was manufactured in humane work conditions

 All employees who worked on this product are paid

customary Swiss market wages and are insured

 ISO 9000:2001 (quality management system)

1.13. The Swiss Association for Quality and Management Systems

The Swiss Association for Quality and Management Systems (SQS) provides certification and assessment services for all types of industries and services. SQS certificates are accepted worldwide thanks to accreditation by the Swiss Accreditation Service (SAS), active membership in the International Certification Network, IQNet, and co-operation contracts/agreements with accredited partners.

www.sqs.ch

The SQS Certificate ISO 9001:2000 has been issued to DIGITAL-LOGIC AG, the entire company, in the field of development, manufacturing and sales of embedded computer boards, embedded computer modules and computer systems. The certification is valid for three years at which time an audit is performed for recertification.

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

2. OVERVIEW

2.1. Standard Features of the MSB900/L

The MICROSPACE 3.5”-SBC is a miniaturized modular device incorporating the major elements of a PC/AT compatible computer. It includes standard PC/AT compatible elements, such as:

 Powerful GEODE LX-900 600MHz  Legacy BIOS ROM  DDR-SODIMM 200pin socket (for DDR-RAM 256-1024MB)  128k second level cache  Timers  DMA  Real-time clock with CMOS-RAM and battery buffer (only on MSB900, not on MSB900L)  LPT1 parallel port  COM1-, COM2- RS2332 serial port  Speaker interface  PS/2-keyboard and mouse interface (shared on one mini DIN connector)  PATA-IDE hard disk interface  VGA video interface  PCI/104 (one slot), limited I/O connector space  4 Channels USB 2.0  Onboard CF socket Type II

2.2. Unique Features

The MICROSPACE 3.5”-SBC includes all standard PC/AT functions plus unique DIGITAL-LOGIC AG enhancements, such as:

 Two channel LAN Ethernet, INTEL 82551QM (LAN A) and INTEL 82551ER (LAN B)  Boot from LAN (PXE and RPL)  Single 8 - 32Volt supply  Video input (only on MSB900, not available on MSB900L)  Watchdog  EEPROM for setup and configuration  UL approved parts  Optional: interface for operator display (LVDS, COM2, CRT, USB, SMBus)

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

2.3. MSB900 Block Diagram

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

2.4. MSB900/MSB900L specifications

CPU Specification

CPU GEODE LX900 CPU Core Supply 1.25V very low powered Mode Real / Protected Compatibility x86 Word Size 32Bits Secondary Cache 128kB Physical Addressing 32 lines Virtual Addressing 16GB Clock Rates 600MHz Socket Standard Soldered BGA

Chipset Specification

Northbridge AMD LX900 Southbridge AMD CS5536 LAN 2x 10/100Mbit Intel 82551QM (LAN A), Intel 82551ER (LAN B) Audio Stereo In and Stereo Line-Out Codec AD1985 up to 96kHz sampling rate, 16Bit (Analog Devices) Firewire IEEE1394 Not on board Video 16MByte Video-DDRAM

Power Management: Specification

The LX900 supports ACPI and APM Version 1.2

The following ACPI Sleep States are supported:

- S1 (Standby)

- S3 (Suspend to RAM) not available

- S4 (Hibernation)

DMA: Specification

8237A comp. 4 channel 8bit

3 channel 16bit

Interrupts: Specification

8259 comp. 8 + 7 levels

PC compatible

Timers: Specification

8254 comp. 3 programmable counters/timers

Memory: Specification

SODIMM SODIMM200pin DDR PC2700 333MHz 256-1024MByte

Video Specification

Controller GEODE LX900 BUS 32Bit high speed 33MHz PCI bus Enhanced BIOS VGA / LCD BIOS Memory 2-16MByte shared RAM CRT-Monitor VGA, SVGA up to 1920x1440 Video Input MSB900: yes, 1 channel

MSB900L: no

Drivers WIN2000, XP

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

Mass Storage Specification

FD Floppy disk interface not supported HD E-IDE interface, AT-type, for max. 2 hard disks, 44pin connector,

for 1.3, 1.8 and 2.5" hard disk with 44 pins IDE

Standard AT Interfaces: Specification

Serial COM1

COM1/2 available on headers onboard.

SuperIO Chip W83627HF from WINBOND Parallel LPT1 printer interface mode: SPP (output), EPP (bidir.) Keyboard AT or PS/2-keyboard Mouse PS/2 Speaker No speaker RTC Integrated into the chipset, RTC with CMOS-RAM 256Byte Backup current RTC-backup MSB900 Onboard 3.6Volt Lithium 400mAh available

RTC-backup MSB900L External connection, no onboard battery available

BUS Specification

PCI/104 PCI 32Bit Bus, 1 slot Clock 33MHz defined by the GEODE

USB Specification

USB 2.0 Transfer rate 480MBps, 12.5MBps / 1.5MBps Channels 4

Peripheral Extension Specification

ISA Not supported PCI MSB900 With PCI/104 BUS (1 slot), limited I/O space

PCI MSB900L Not available

Power Supply Specification

Working Power Rise Time Unspecified Power consumption MSB900/L with HD, MS/KB (PS/2), CRT Monitor

Standby power consumption MSB900/L:

Physical Characteristics Specification

Dimensions Length: 146 mm

Weight 160g PCB Thickness 1.6mm / 0.0625 inches nominal PCB Layer Multilayer

Name FIFO IRQs Addr. Standard Option

yes

COM2

For DSub-connectors, option MSB800-CON is needed.

<5 µA

8-32Volt ± 5% (peak 36Volt)

Windows XP Desktop: type 8.5-10W

Windows Standby: 2.5W (without MS/KB wakeup function) Windows Standby: 4.5W (with PS/2 wakeup function)

Depth: 102 mm Height: 20 mm

yes

IRQ4 IRQ3

3F8 2F8

RS232C RS232C

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

Operating Environment Specification

Relative humidity 5-90%, non-condensing Vibration 5-2000Hz, 0.1G Shock 1G Temperature MSB900*:

Operating: Standard version: -25°C to +70°C Extended version: -40°C to +85°C Storage: -55°C to +85°C * = with passive cooler

MSB900L**: Operating: Standard version: 0°C to +60°C

Storage: -55°C to +85°C ** = without passive cooler

EMI/EMC (IEC1131-2 refer MIL 461/462)

ESD Electro Static Discharge IEC 801-2, EN55101-2, VDE 0843/0847 Part 2

REF Radiated Electromagnetic Field IEC 801-3, VDE 0843 Part 3, IEC770 6.2.9. (not tested) EFT Electric Fast Transient (Burst) IEC 801-4, EN50082-1, VDE 0843 Part 4

SIR Surge Immunity Requirements IEC 801-5, IEEE587, VDE 0843 Part 5

High-frequency Radiation EN55022

Compatibility Specification

MSB900/L Mechanically compatible to 3.5inch industrial embedded com-

All information is subject to change without notice.

Specification

Metallic protection needed Separate ground layer included 15kV single peak

250V - 4kV, 50 ohms, Ts=5ns Grade 2: 1kV Supply, 500 I/O, 5kHz

Supply: 2kV, 6 pulse/minute I/O: 500V, 2 pulse/minute FD, CRT: none

puter boards

2.5. Examples of Ordering Codes

802220 MSB900 with LX900 CPU, 0MB-RAM, Battery, PCI/104 and Video input 802221 MSB900L with LX900 CPU, 0MB RAM, … 802205 MSB800CON COM1, LPT1 Expansion board.

These are only examples; for current ordering codes, please see the current price list.

2.6. Related Application Notes

Application Notes are available at http://www.digitallogic.com  support, or on any DIGITAL-LOGIC Application CD.

# Description

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

2.7. Dimensions & Diagrams

2.7.1. MSB900/L

Board / Version Unit: Tolerance: Date / Author

MSB900/L mm (millimeter) + / - 0.1mm 25.10.2006 / BRR

DIGITAL-LOGIC AG MSB900/L Detailed Technical Manual V1.0

+ 46 hidden pages