Compaq FP 7020 User Manual

User’s Guide

Compaq 7020 Flat Panel Monitor

Document Part Number: 254041-003

April 2002

Enhanced for accessibility

Technologies Group, L.P. in the United States and/or other countries. Microsoft, MS-DOS, Windows, Windows NT are trademarks of Microsoft

Corporation in the United States and/or other countries. All other product names mentioned herein may be trademarks of their

respective companies. Compaq shall not be liable for technical or editorial errors or omissions

contained herein. The information in this document is provided “as is” without warranty of any kind and is subject to change without notice. The warranties for Compaq products are set forth in the express limited warranty statements accompanying such products.

Nothing herein should

be construed as constituting an additional warranty.

Compaq service tool software, including associated documentation, is the property of and contains confidential technology of Compaq Computer Corporation. Service customer is hereby licensed to use the software only for activities directly relating to the delivery of, and only during the term of, the applicable services delivered by Compaq or its authorized service provider. Customer may not modify or reverse engineer, remove, or transfer the software or make the software or any resultant diagnosis or system management data available to other parties without Compaq’s or its authorized service provider’s consent. Upon termination of the services, customer will, at Compaq’s or its service provider’s option, destroy or return the software and associated documentation in its possession.

CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.

WARNING: Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life.

User’s Guide Third Edition (April 2002) First Edition (July 2001) Part Number: 254041-003

Unpacking

Before unpacking the monitor, prepare a suitable workspace for your monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that monitor has enough space around it for sufficient airflow. Though the monitor uses very little power, some ventilation is needed to ensure that the monitor does not become too hot.

After you unpack the monitor box, make sure that the following items were included in the box:

■

Monitor

■

1.5M Monitor-to-PC VGA Cable

■

2M Monitor-to-PC DVI-D Cable (digital models only)

■

1.5M Stereo Jack Audio Cable (speaker models only)

Installation

■

1.8M Power Cord

■

AC Adapter

■

User’s Guide

If you find that any of these items is missing or appears damaged, contact your dealer immediately.

Compaq 7020 Flat Panel Monitor User’s Guide 1-1

Installation

Viewing Angle Adjustment

The monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted as follows: Top (-5°~ +35°) & Left / Right (-45° to +45°).

Figure 1-1

CAUTION:

viewing angle settings as stated above. Attempting this will result in damaging the monitor and monitor stand.

Do not force the monitor over its maximum

1-2 Compaq 7020 Flat Panel Monitor User’s Guide

Detaching Monitor from Its Stand

1. Remove the rear panel 1 from the monitor. (see Fig. 1-2)

Installation

2. Remove the rear support panel support column.

3. Unscrew screws

Figure 1-2

the swivel base support column 4.

from the swivel base

Compaq 7020 Flat Panel Monitor User’s Guide 1-3

Installation

Connecting the Display to the Swivel Base

Before connecting the display to the swivel base support column, please refer to Fig.1-2.

The rear of this display has four integrated 4 mm, 0.7 pitch, threaded holes, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-3. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2.1 and 2.1.3, version 1, dated 13 November 1997).

Figure 1-3

1-4 Compaq 7020 Flat Panel Monitor User’s Guide

Cable Installation

Please follow these instructions to install the cables.

1. Remove the back panel

(See Fig. 1-4).

2. Remove the rear support panel

support column.

3. Place the signal cable, the DC power cable and the audio

cable into their correct respective grooves

from the rear of the monitor.

from the swivel base

Installation

Figure 1-4

Compaq 7020 Flat Panel Monitor User’s Guide 1-5

Installation

Connecting the Display to Your Computer

1. Power off your computer.

2. Connect one end of the signal cable to the monitor's VGA

port or DVI port (digital models only). (See Fig. 1-5)

3. Connect the other end of the signal cable to the VGA port

or DVI port on your PC.

4. Make sure both connections are secure.

Figure 1-5

WARNING: This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. A ferrite-core interface cable is included in the monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used.

1-6 Compaq 7020 Flat Panel Monitor User’s Guide

Connecting the AC Power

1. Connect the power cord to the AC adapter. (See Fig. 1-6)

2. Connect the AC adapter's DC output connector to the DC

Power Jack of the monitor.

3. Connect the power cord to an AC power source.

Installation

Figure 1-6

WARNING: We recommend to install a "Surge Protector" device between the AC Adapter and the electrical wall outlet for adding protection against power surges to prevent the effects of sudden voltage variations from reaching the monitor. Sudden power surges may damage your monitor.

Compaq 7020 Flat Panel Monitor User’s Guide 1-7

Installation

Connecting the Audio Cable

The instructions in this section apply only to monitor models featuring speakers.

1. Connect the audio cable to the " LINE OUT " jack on your

PC's audio card or to the front panel's "AUDIO OUT" jack of your CD ROM drive. (See Fig. 1-7)

2. Connect the other end of the audio cable to the monitor's "

LINE IN " jack.

Figure 1-7

1-8 Compaq 7020 Flat Panel Monitor User’s Guide

Setting Up the Monitor

1. Make sure the AC Adapter is connected to the monitor.

2. Turn on the monitor's power switch, located on the bezel of

the monitor.

Power Management System

The monitor supports one low power mode. When the monitor is in the low power mode, the monitor screen will be blank and the power LED indicator will light amber.

Installation

Compaq 7020 Flat Panel Monitor User’s Guide 1-9

+ 24 hidden pages