Technologies Group, L.P. in the U.S. and/or other countries.
Microsoft and Windows are trademarks of Microsoft Corporation in the U.S. and/or other
countries.
All other product names mentioned herein may be trademarks of their respective
companies.
This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation and is intended for home and
other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Compaq shall not be liable for technical or editorial errors or omissions contained herein.
The information is provided “as is” without warranty of any kind, and is subject to
change without notice. The warranties for Compaq products are set forth in the express
limited warranty statements accompanying such products. Nothing herein should be
construed as constituting an additional warranty.
Compaq Notebook Series Reference Guide
First Edition (September 2002)
This manual is printed on recycled paper.
2 Reference Guide
Important Safety Information
CAUTION
To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line
cord to connect a modem to the telephone wall jack. In Australia, the computer
must be connected to the Telecommunication Network through a line cord that
meets the requirements of ACA Technical Standard TS008.
When using your computer with a telephone connection, always follow basic safety
precautions to reduce the risk of fire, electric shock, and injury to persons:
Do not use this product with a telephone connection near water (for example, near a
•
bathtub, sink, swimming pool, or in a wet basement).
•
Avoid using a telephone connection (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
•
Do not use a telephone connection to report a gas leak in the vicinity of the leak.
•
Use only the power cord and batteries indicated in this manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for possible special
disposal instructions.
•
Disconnect the modem cable before opening the computer case or touching an
uninsulated modem cable, jack, or internal component.
•
Do not plug a modem cable or telephone cable into the network (LAN) receptacle.
Software Product License Agreement
Your HP product contains software programs. CAREFULLY READ THIS LICENSE
AGREEMENT BEFORE PROCEEDING TO OPERATE THIS EQUIPMENT. RIGHTS
IN THE SOFTWARE ARE OFFERED ONLY ON THE CONDITION THAT THE
CUSTOMER AGREES TO ALL TERMS AND CONDITIONS OF THE LICENSE
AGREEMENT. PROCEEDING TO OPERATE THE EQUIPMENT INDICATES
YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF YOU DO NOT
AGREE WITH THE TERMS OF THE LICENSE AGREEMENT, YOU MUST NOW
EITHER REMOVE THE SOFTWARE FROM YOUR HARD DISK DRIVE AND
DESTROY THE MASTER DISKETTES, OR RETURN THE COMPLETE HP
PRODUCT AND SOFTWARE FOR A FULL REFUND. PROCEEDING WITH
CONFIGURATION SIGNIFIES YOUR ACCEPTANCE OF THE LICENSE TERM S.
UNLESS OTHERWISE STATED BELOW, THIS HP SOFTWARE LICENSE
AGREEMENT SHALL GOVERN THE USE OF ALL SOFTWARE THAT IS
PROVIDED TO YOU AS PART OF THE HP PRODUCT AND SHALL SUPERSEDE
ANY OTHER SOFTWARE WARRANTY STATEMENT THAT MAY BE INCLUDED
IN THIS HP PRODUCT OR MAY BE FOUND ONLINE.
Reference Guide 3
Operating system and software applications by Microsoft are licensed to you under the
Microsoft License Agreement contained in the Microsoft documentation or displayed on
your screen when Microsoft Software Products are launched.
For a PC supplied with a Microsoft operating system: When you start the PC and accept
the Microsoft End-user License Agreement (“EULA”), your license rights are valid only
if a Certificate of Authenticity (“COA”) label corresponding to your Microsoft operating
system is provided with your PC. The COA label can usually be found on the bottom of
the computer. If the COA label does not correspond to your Microsoft operating system
or is missing, contact your HP reseller for details.
Other non-HP Software and Operating Systems are covered by the appropriate vendor
license. The following License Terms govern the use of the HP software:
USE. Customer may use the software on any one HP product. Customer may not network
the software or otherwise use it on more than one HP product. Customer may not reverse
assemble or decompile the software unless authorized by law.
COPIES AND ADAPTATIONS. Customer may make copies or adaptations of the
software a) for archival purposes or (b) when copying or adaptation is an essential step in
the use of the software with an HP product so long as the copies and adaptations are used
in no other manner.
OWNERSHIP. Customer agrees that he/she does not have any title or ownership of the
software, other than ownership of the physical media. Customer acknowledges and
agrees that the software is copyrighted and protected under the copyright laws. Customer
acknowledges and agrees that the software may have been developed by a third party
software supplier named in the copyright notices included with the software, who shall be
authorized to hold the Customer responsible for any copyright infringement or violation
of this Agreement.
PRODUCT RECOVERY CD-ROM or DVD. If your HP product was shippe d with a
product recovery CD-ROM or DVD: (i) The product recovery CD-ROM or DVD and/or
support utility software may only be used for restoring th e hard disk of the HP product
with which the product recovery CD-ROM or DVD was originally provided. (ii) The use
of any operating system software by Microsoft contained in any such product recovery
CD-ROM or DVD shall be governed by the Microsoft License Agreement.
TRANSFER OF RIGHTS IN SOFTWARE. Customer may transfer rights in the software
to a third party only as part of the transfer of all rights and only if Customer obtains the
prior agreement of the third party to be bound by the terms of this License Agreement.
Upon such a transfer, Customer agrees that his/her rights in the software are terminated
and that he/she will either destroy his/her copies and adaptations or deliver them to the
third party.
SUBLICENSING AND DISTRIBUTION. Customer may not lease, sublicense the
software or distribute copies or adaptations of the software to the public in physical
media or by telecommunication without the prior written consent of Hewlett-Packard.
TERMINATION. Hewlett-Packard may terminate this software license for failure to
comply with any of these terms provided Hewlett-Packard has requested Customer to
cure the failure and Customer has failed to do so within thirty (30) days of such notice.
4 Reference Guide
UPDATES AND UPGRADES. Customer agrees that the software does not include
updates and upgrades which may be available from Hewlett-Packard under a separate
support agreement.
EXPORT CLAUSE. Customer agrees not to export or re-expor t the software or any copy
or adaptation in violation of the U.S. Export Administration regulations or other
applicable regulation.
U.S. GOVERNMENT RESTRICTED RIGHTS. Use, duplication, or disclosure is subject
to HP standard commercial license terms and for non-D OD Departments and Agencies of
the U.S. Government, the restrictions set forth in FAR 52.227-19(c)(1-2) (June 1987)
Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U.S.A. Copyright
(c) 2000 Hewlett-Packard Company. All Rights Reserved. Customer further agrees that
Software is delivered and licensed as “Commercial computer software” as defined in
DFARS 252-227-7014 (June 1995) or as a “commercial item” as defined in FAR
2.101(a), or as “Restricted computer software” as defined in FAR 52.227-19 (or any
equivalent agency regulation or contract clause), whichever is applicable. The Customer
agrees that it has only those rights provided for such Software by the applicable FAR or
DFARS clause or the HP standard software agreement for the product involved.
Support Policy for Microsoft Operating Systems Service Pack. HP will provide end user
support for HP PCs that use Microsoft Operating Systems, including its latest service
packs. This support will be available 30 days after the service pack being released by
Microsoft.
Reference Guide 5
Contents
Getting Started with Your Notebook............................................................................11
Congratulations! Your notebook computer sets a new standard in personal computing.
Although compact and easy to carry, your computer is made with high standards of
quality and attention to detail.
This manual shows how to set up and operate your computer, as well as what to do if you
run into trouble.
What’s in the box?
• Notebook PC.
• Battery (installed).
• AC adapter and power cord.
• Quick Setup poster.
• Startup Guide.
• Documentation Library CD.
• QuickRestore System Recovery CD, for restoring Windows and all software included
with your computer.
• Microsoft Windows manual.
• CD with special software (for models with certain types of drives).
In addition, your notebook includes preinstalled software. (The exact software installed
depends on your particular notebook model.)
12 Reference Guide
Getting Started with Your Notebook
Taking Inventory
To buy accessories
You can buy accessories for your computer online. For the latest accessories and options,
visit the Compaq Consumer Support Web site (www.compaq.com/consumersupport).
We currently offer accessories such as the following:
• AC adapter.
• RAM modules for expanding memory.
• Battery.
• Port replicator.
To find more information
The following table lists other sources of information about your computer and related
products.
Source Description and Location
Startup Guide
Reference Guide
Microsoft Windows
manual
Compaq Consumer
Support Web site
This printed manual introduces your computer. It also contains setup instructions,
basic operation guidelines, troubleshooting information, and warranty information.
The Reference Guide is shipped on the Documentation Library CD that comes with
your computer, and provides a complete source for operating and maintaining the
computer.
This is shipped with your computer and contains information about using the version
of Microsoft Windows shipped with your computer.
www.compaq.com/consumersupport
To select another language, see www.compaq.com.
Reference Guide 13
Getting Started with Your Notebook
Identifying Parts of the Computer
Identifying Parts of the Computer
Front View
1. Computer open/close latch.
2. One-Touch buttons.
3. Keyboard status lights.
4. Power button. Turns the computer on and off.
5. Touch pad, scroll pad, click buttons, plus on-off
button.
6. Main status lights (left to right): power mode, hard
disk activity, battery.
14 Reference Guide
7. Hard disk drive.
8. Infrared port (certain models).
9. Wireless on-off button and indicator light (certain
models).
10. Battery.
11. CD-ROM, DVD, or other drive.
12. PS/2 keyboard or PS/2 mouse port (supports
Y adapter).
Getting Started with Your Notebook
Identifying Parts of the Computer
Back View
13. AC adapter jack.
14. Two universal serial bus ports (USB).
15. LAN port.
16. S-video port.
17. Parallel port (LPT1). Use this port for a parallel
printer or other parallel device.
18. Serial port (COM1). Use this port for a serial
mouse, modem, printer, or other serial device.
19. External monitor port.
20. Kensington lock slot (security connector).
Reference Guide 15
21. Modem port.
22. PC Card and CardBus slot and button (certain
models have two slots and two buttons).
23. IEEE 1394 port (certain models).
24. Audio jacks (left to right): external microphone,
audio out (headphones).
25. Volume control.
26. Audio mute button and audio mute light.
27. Floppy disk drive (certain models).
Getting Started with Your Notebook
Identifying Parts of the Computer
Bottom View
28. Hard disk drive.
29. Battery latch.
30. RAM cover.
31. Reset button.
32. Docking port (certain models).
33. Mini-PCI cover (no user parts inside).
16 Reference Guide
Getting Started with Your Notebook
Identifying Parts of the Computer
Status Lights
The computer includes a number of status lights that report power and battery status,
drive activity, and keyboard functions such as Caps Lock and Num Lock.
The following diagram shows the main status lights on the front of the computer.
1. Power mode.
• On: the computer is on (even if the display is off).
• Blinking: the computer is in Standby mode.
• Off: the computer is off or in Hibernate mode.
2. Hard disk drive activity.
• On: computer is accessing the hard disk drive.
3. Battery status.
• Green: the AC adapter is connected and the battery is fully charged.
• Amber: the AC adapter is connected and the battery is charging.
• Blinking: the AC adapter is connected and the battery is missing or has a fault.
• Off: the AC adapter is not connected.
Reference Guide 17
Getting Started with Your Notebook
Identifying Parts of the Computer
The keyboard status lights, located above the keyboard, indicate the states of the
keyboard locks.
1. Caps Lock. Caps Lock is active.
2. Num Lock. Num Lock is active. (The Keypad Lock must also be on to use the
embedded keypad.)
3. Keypad Lock. The embedded keypad is active (Fn+F8). Num Lock must also be on
for the numeric keys—otherwise, cursor control is active (as marked on an external
keyboard).
18 Reference Guide
Getting Started with Your Notebook
Setting Up Your Computer
Setting Up Your Computer
WARNING
WARNING
Improper use of keyboards and other input devices has been associated with
ergonomic injury. For information about reducing your risk, see the Safety & Comfort Guide on the Documentation Library CD included with your computer, or
visit our ergonomics Web site, www.hp.com/ergo.
If you are using your notebook computer as your primary computer, or using it for
extended periods, you should use it with a full-size keyboard, monitor, and mouse.
Docking accessories offer quick, easy connections to these devices. This can reduce
the risk of ergonomic injury. See the Safety & Comfort Guide on the Documentation Library CD, or visit our ergonomics Web site, www.hp.com/ergo.
When you set up your computer for the first time, you’ll install and charge the battery,
connect the AC adapter, turn on the computer, and run the Windows setup program.
Step 1: Install the battery
Do not mutilate or puncture batteries. Do not dispose of batteries in fire, or they
can burst or explode, releasing hazardous chemicals. Rechargeable batteries must
be recycled or disposed of properly.
Your computer is shipped with the battery installed. If the battery has been removed, you
should install it:
1. Turn the computer upside down.
2. Insert the connector end of the battery into the battery compartment and slide it in
until it latches.
Reference Guide 19
Getting Started with Your Notebook
Setting Up Your Computer
To remove the battery
1. Before removing the battery, do one of the following:
• Shut down the computer or put it into Hibernate mode, or
• Plug in the AC adapter.
2. Slide the battery’s release latch, and then slide the battery out of its compartment.
20 Reference Guide
Getting Started with Your Notebook
Setting Up Your Computer
Step 2: Connect AC power
CAUTION
Important
Use only the F4600, F4814, or 0950-4334 AC adapter included with your computer
(or other approved adapter that meets the power requirements of the computer).
Do not use a 60-watt, 3.16-amp adapter, such as F1454A or F1781A, and do not use
DC adapter accessories F1455A and F2297A.
Using the wrong AC adapter could damage the computer or adapter and may void
your warranty (see "Limited Warranty Statement" on page 130).
• Plug the AC adapter into the computer and connect the power cord to the AC adapter,
then plug the power cord into a wall outlet. The computer’s battery then starts
charging.
When unplugging the power cord, unplug it from the outlet before unplugging it from
the AC adapter.
While the battery is charging, you can continue with step 3.
Reference Guide 21
Getting Started with Your Notebook
Setting Up Your Computer
Step 3: Connect a phone line
1. Make sure the telephone line is an analog line, sometimes called a data line. (You
must not use a digital line.)
2. Connect the telephone cord into a telephone jack. If the plug on the phone cord
doesn’t fit the jack, you may need to use an adapter.
3. Plug the other end of the phone cord into the built-in modem.
For details about using the modem, see “Using the Modem” on page 54.
22 Reference Guide
Getting Started with Your Notebook
Setting Up Your Computer
Step 4: Turn on the computer
• Press the power button above the left side of the keyboard. The computer then boots
up, and Windows starts automatically.
Hint
If your computer does not turn on when operating on battery power, the battery may be
out of power. Plug in the AC adapter and press the power button again. Leave the AC
adapter plugged in for at least an hour—or 2–3 hours to charge it fully.
Step 5: Set up Windows
Your notebook computer has Microsoft Windows preinstalled on its hard disk drive. The
first time you turn on your computer, the Windows Setup program runs automatically so
you can customize your setup.
1. Follow the Setup program’s instructions as they appear on the screen. If the program
prompts you to enter the Product ID code, you will find this code on the bottom of the
computer.
2. Check the modem’s country or region settings: click Start, Control Panel, Printers and
Other Hardware, Phone and Modem Options, and then click Edit on the Dialing Rules
tab.
Reference Guide 23
Getting Started with Your Notebook
Setting Up Your Computer
To connect to the Internet
If you are connected to a wired or wireless LAN with Internet access or your computer
has a modem (built-in, PC Card, or external), you can connect to the Internet. For details,
see “Using the Modem” on page 54, “Connecting to a LAN” on page 61, or “Making
Wireless Network Connections” on page 62.
What to do next
• If you’re not familiar with Windows XP, click Start, Tour Windows XP, or check the
Windows manual to discover what’s new.
• See the Reference Guide on the Documentation Library CD to learn more about using
and maintaining your computer.
24 Reference Guide
Basic Operation
Reference Guide 25
Basic Operation
Operating Your Computer
Operating Your Computer
You can start and stop your computer using its power button. However, at certain times
you may want to use other methods to start or stop the computer—depending on power
considerations, types of active connections, and start-up time.
To turn the computer on and off
Power mode To enter this mode
On mode
Power mode status light is on.
Standby mode
Saves significant power.
Turns off the display and other components.
Maintains current session in RAM.
Restarts quickly.
Restores network connections.
Power mode status light is blinking.
Hibernate mode
Saves maximum power.
Saves current session to disk, then shuts down.
Restores network connections.
Power mode status light is off.
Shut down (off)
Saves maximum power.
Turns off without saving current session.
At startup, resets everything, starts a new
session, and restores network connections.
Power mode status light is off.
To turn on: Press the power button to restart, or to resume your session from Standby or Hibernate mode.
You can also customize how these power modes work—see “How the computer manages
power automatically” on page 46.
Press the power button.
Press the power button
–or–
click Start, Turn Off Computer, Stand By
–or–
allow timeout.
Press Fn+F12
–or–
allow timeout.
Click Start, Turn Off Computer, Turn Off
–or–
press the power button for 4 seconds (only if the Start
menu procedure doesn’t work).
26 Reference Guide
Basic Operation
Operating Your Computer
To reset the computer
Occasionally, you may find that Windows or the computer has stopped responding, and
will not let you turn the computer off. If this happens, try the following in the order listed.
• If possible, shut down Windows: press CTRL+ALT+DEL, and then click Shut Down,
Restart.
–or, if this fails–
• Press the power button for 4 seconds until the display shuts down, and then press the
power button again to restart.
–or, if this fails–
• Insert the tip of a ballpoint pen into the reset button on the bottom of the computer,
and then press the power button to restart.
To reset the computer while it’s docked in a port replicator, you can press the reset button
on the left side of the port replicator.
Reference Guide 27
Basic Operation
Operating Your Computer
To change the boot device
The computer normally boots from its internal hard disk. You can also boot the computer
from a floppy disk drive, a CD-ROM drive, or an internal network interface card.
1. Click Start, Turn Off Computer, Restart.
2. When the logo screen appears, press ESC to display the Boot menu.
3. Use the arrow keys to select the boot device, and press ENTER.
If you want to boot from a specific device whenever it is present, change the boot order
using the BIOS Setup utility—see “To run the BIOS Setup utility” on page 118.
To use the touch pad
The touch pad includes an on-off button so you can turn off the touch pad to avoid
moving the pointer accidentally, such as by touc hing t he pa d while typing. The indicator
light turns off when you turn off the touch pad.
28 Reference Guide
Basic Operation
Operating Your Computer
1. Click buttons. These work like the left and right buttons on a standard mouse.
2. Touch pad (touch-sensitive pointing device).
3. Touch pad on-off button and indicator lig ht .
4. Scroll pad. The scroll pad scrolls the contents of the active window.
Moving and selecting
1. Place your hands in a normal typing position.
2. Move a thumb or finger across the touch pad in the direction you want the pointer to
move.
3. Use the left and right click buttons, which function like the left and right buttons on a
mouse, to make your selection:
• To open an application, move the pointer over the icon and double-click the left
button.
• To make menu selections, move the pointer to the menu item and click the left
button.
• To open the shortcut menu for an item, move the pointer over the item and click
the right button.
• To drag an item, move the pointer over the item. Then press and hold the left
button while you move the pointer to the new location, and release the button.
In addition, you can tap the touch pad to select items and use other advanced touch pad
features. For more information, double-click the touch pad icon in the taskbar, and then
click Help in the tab for a particular feature.
You can use Mouse in Control Panel or the touch pad icon in the taskbar to customize the
operation of your computer’s pointing devices (touch pad and external mouse): you can
change the left, right, and scroll pad actions, double-click speed, pointer speed, and more.
Scrolling with the scroll pad
• Move your finger down the scroll pad to scroll down through the contents of a
window. Move your finger up the scroll pad to scroll up.
Reference Guide 29
Basic Operation
Operating Your Computer
To use the Fn hot keys
The combination of the Fn key plus another key creates a hot key—a shortcut key
sequence—for various system controls. To use a hot key, press and hold Fn, press the
appropriate second key, and then release both keys.
This hot key Does this
Fn+F1 Decreases the display brightness.
Fn+F2 Increases the display brightness.
Fn+F5
Fn+F8
Fn+F12 Enters Hibernate mode.
Fn+NumLock Toggles Scroll Lock on and off.
Fn+Page Up Increases the audio volume and cancels the mute setting.
Fn+Page Down Decreases the audio volume.
Fn+Backspace Mutes the audio output.
Toggles among the built-in display, an external display, and simultaneous display on
both.
Toggles the built-in keypad on and off. Does not affect an external keyboard. If Num
Lock is on, then the numeric functions are active; otherwise, cursor control is active
(as marked on an external keyboard).
30 Reference Guide
Basic Operation
Operating Your Computer
To use the One-Touch buttons
Your computer includes five One-Touch buttons that can start any application or open a
document or Web site with a single press.
• Press the One-Touch button to open the corresponding application, document, or
Web site.
Your computer is preconfigured to access the following services:
1. Microsoft Outlook Express e-mai l software .
2. Internet search.
3. Internet shopping.
4. Quick Lock—see “To lock your computer” on page 38.
5. Internet notebook support.
To reprogram a One-Touch button
1. Click Start, All Programs, Utilities, One-Touch, One-Touch Configuration.
2. On the One-Touch tab, click the button you want to reprogram.
3. Type a label for the button, and then select the application , do cument, folder, or Web
site you want the button to open.
4. If you want a label to appear onscreen when you press a One-Touch button, select that
option on the Onscreen Display tab.
Reference Guide 31
Loading...
+ 124 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.