
Switching Mode Power Supply 480 Watt DIN-Rail
Mounting for Ethernet Switches with PoE
PS48VDC-10A
HARDENED
ComNet™ model PS48VDC-10A is a high-quality, low-noise switching mode power
supply ideally suited to those applications requiring PoE (Power over Ethernet).
This rugged unit may be either DIN-rail or shelf-mounted, providing an identical
mounting configuration to the mating PoE switch. Up to 24 PoE field devices may
be powered from a single supply, and the high output current capacity provides
an adequate safety margin. A maximum of three of these units may be paralleled
together to triple the number of PoE devices supported. The wide ambient operating
temperature range permits installation in most out-of-plant and unconditioned
environments, such as those found in intelligent transportation systems or factory
automation/industrial control applications. Unconditional line and load protection
is provided.
FEATURES
› Universal AC input: 90 to 264 VAC, 47-63Hz
› Mounts on standard 7.5 or 15 mm DIN-rail
› Automatic power factor correction (PFC)
› High operating efficiency; up to 90%
› Small package for limited space installations
› Natural convection cooling; no troublesome fans
APPLICATIONS
› Power Supply for Ethernet Switches with PoE
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427

PS48VDC-10A
SPECIFICATIONS
Switching Mode Power Supply 480 Watt DIN-Rail
Mounting for Ethernet Switches with PoE
Electrical
Line regulation ± 0.5%
Load regulation,
Non-parallel mode ± 0.5%
Load regulation,
Parallel mode ± 5%
Ouput Voltage accuracy 1% (factory adjusted)
Ripple and Noise 100 mV
Hold up time Vi = 230Vac 30 ms
Minimum load 0%
Parallel Operation 3 units max.
Input Data
Rated input voltage range
AC 90 - 264 Vac
DC 120 - 370 Vdc
Rated input current
(115/230 VAC) 7 / 3.5A
Frequency range 47 to 63 Hz
Inrush current
Vi= 115Vac 25A
Vi= 230Vac 50A
Controls and Protections
Input Fuse T10A/250 VAC internal¹
Output Overvoltage Protection 57 to 63 VDC
Output Short Circuit Protection Current limit
Rated Overload Protection 120-140%
General Data
(@ Nominal Line, Full Load, 25ºC)
Ambient operating
temperature -25° to +71°C
Derating (>56°C to +71°C) 2.5%/°C
Ambient humidity 20 - 95%RH, non-condensing
Storage -25° to +85°C
Dimensions L × W × D
screw terminal connector: 4.9 × 6.9 × 4.8 in (12.5 × 17.5 × 12.3 cm)
plug connector version: 5.6 × 6.9 × 4.8 in ( 14.2 × 17.5 × 12.3 cm)
Cooling Natural convection
Case material Aluminium, Powder Coat Finish
Weight < 4.3 lb / 1.9 kg
Protection IP20
Approvals And EMC Compliance²
Insulation voltage I/O 3.000Vac
Insulation resistance I/O
@ 500VDC 100Mohm
UL / cUL UL508 listed, UL60950-1, Recognised
TUV EN60950-1
CE EN61000-6-3
EN55022 class B
EN61000-3-2
EN61000-3-3
EN61000-6-2
EN55024
[1] When S/P switch is set to parallel, it is not possible to trim output
voltage.
[2] For complete compliance information contact ComNet for
manufacturer’s data sheet.
Pin Assignment and Front Controls
Pin # Designation Description
1 + Positive output terminal
2 + Positive output terminal
3 - Negative output terminal
4 - Negative output terminal
5 GND Ground terminal to minimise High frequency emissions
6 L Phase input ( no polarity with DC input )
7 N Neutral input ( no polarity with DC input )
DC ON DC output ready LED
DC LO DC low indicator LED
Vout ADJ. Trimmer for fine output voltage adjustment
S/P Single parallel selection switch
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427

PS48VDC-10A
Switching Mode Power Supply 480 Watt DIN-Rail
Mounting for Ethernet Switches with PoE
SPECIFICATIONS
Installation Derating Diagram
Cooling Natural air convection
Allow 25 mm of free space along all sides to
ensure adequate cooling
Screw Connections 10 to 24AWG Flexible or solid cable
Plug In Connectors 10 to 24AWG Flexible or solid cable
NOTE: Specify desired connector style at time of order.
Outline Drawing
ORDERING INFORMATION
Output
Part Number
PS48VDC-10A 10 47. 0 56.0 37.0 40.0 3 7.0 40.0 90%
[1] When S/P switch is set to parallel, it is not possible to trim output voltage.
Current (A)
Voltage Trim Range¹ DC OK @ Start Up (VDC) DC Low After Start Up (VDC)
Typical
EfficiencyMin. VDC Max. VDC Min. Max. Min. Max.
OPTIONAL FEATURES
Code Description
B Plug-in connectors
3 CORPORATE DRIVE
8 TURNBERRY PARK ROAD
|
DANBURY, CONNECTICUT 06810
|
GILDERSOME
|
MORLEY
|
|
USA
T: 203.796.5300
|
LEEDS, UK LS27 7LE
|
F: 203.796.5303
|
T: +44 (0)113 307 6400
|
TECH SUPPORT: 1.888.678.9427
|
F: +44 (0)113 253 7462
|
INFO-EUROPE@COMNET.NET
|
INFO@COMNET.NET
05 Feb 2015© 2015 Communic ation Networ ks. All Right s Reserve d. “ComNet ” and the “ComNe t Logo” are regis tered tra demarks of Comm unication Net works.