Comnet netwave NWKED Quick Start Manual

Download

Page 1

QUICK START GUIDE

NWKED

VIDEO ENCODER/DECODER KIT FOR USE WITH NETWAVE WIRELESS ETHERNET

This manual serves the following ComNet Model Number:

NWKED

Thank you for purchasing NetWave® from ComNet. This quick start guide is designed to walk you through installation.

This guide applies to the following models:

NWKED: Analog Video Encoder/Decoder Kit for use with NetWave Wireless Ethernet

See Figures 1 through 4 for Installation instructions.

INS_NWKED_QS_REV– 05/20/13 PAGE 1

Page 2

QUICK START USER GUIDE NWKED

FIGURE 1 – NWKED ENCODER

FIGURE 2 – NWKED DECODER

TECH SUPPORT: 1.888.678.9427

INS_NWKED_QS_REV– 05/20/13 PAGE 2

Page 3

QUICK START USER GUIDE NWKED

FIGURE 3 – INSTALLATION INSTRUCTIONS

Step 1.

Unpack the hardware from the box. Instructions for the Decoder and the Encoder are the same.

Step 2.

A. Connect the Power Adapter with the Terminal Block B. Connect the Terminal Block to the power port on the device

Step 3.

Connect the video source to BNC Port on the Encoder. Press and twist the BNC connector to ensure a secure fit.

Connect the Coaxial cable from the receiver to the composite port on the Decoder. Press and twist the BNC connector to ensure a secure fit.

Step 4.

A. Connect one end of an RJ-45 Ethernet cable to the OUT port

of the Power Injection Module (PIM) and the other end to LAN of the access point.

Maximum length of the RJ-45 CAT5 cable is 100 meters.

B. Connect the RJ-45 Ethernet cable attached to the PIM to the

Encoder/Decoder.

C. Connect the power adaptor to the main electrical supply and

the power plug into the socket of the PIM.

PoE power input: Passive PoE (range 12 to 24 VDC)

D. Connect the RJ-45 cable from Port 2 on the access point to

an external PoE device, typically a camera as shown.

E. A Drip Loop is recommended as additional precaution

against moisture.

E E

TECH SUPPORT: 1.888.678.9427

INS_NWKED_QS_REV– 05/20/13 PAGE 3

Page 4

QUICK START USER GUIDE NWKED

INSTALLATION REQUIREMENTS

Shielded outdoor CAT 5 or better should be used for all out of plant Ethernet connection and should be properly grounded through the PoE AC ground. Industrial grade shielded Ethernet cable is recommended to help prevent ESD damage commonly experienced with outdoor installations. Visit www.comnet.net/comnet-products/cables

CONFIGURING NETWAVE

1. Connect an Ethernet cable from the port labelled as Ethernet on the Encoder or Decoder to either a laptop or a PC LAN port.

2. Connect the terminal block the provided power supply and connect to the Encoder/Decoder. Connect the power supply to a power outlet. You should notice the red PWD LED illuminate.

3. Set the IP address of the laptop being used to configure Netwave to static and the subnet to 192.168.10.x/24 subnet.

4. Point the browser to the Encoder/Decoder IP address. The default addresses are: Decoder: 192.168.10.200 Encoder: 192.168.10.201 NOTE: Internet Explorer 11 in Compatibility mode is highly recommended.

5. A login prompt will pop up. Enter: ID: admin Password: 123456

6. To configure the Decoder login then Select Connection Settings and set the desired settings.

• Select Apply Settings

• Select Save

• Select Reboot to store settings.

7. To configure the Encoder login then Select the Setup Tab and make the necessary changes.

• Select Apply Settings

• Select Save

• Select Reboot to store settings.

DEFAULT CONFIGURATIONS

IP Address of Decoder Web Server 192.168.10.200

IP Address of Encoder Web Server 192.168.10.201

LAN Mode for Web Server Static Addressing

Web Server User ID admin

Web Server Password 123456

Video Stream MPEG4

NOTE: A Reset to defaults (performed on the ADMIN page) will erase all user configurations.

Connection Type TCP

Enable Audio In Off

Enable Control Data On

Stream Port 6002

Control Port 6001

FIGURE 4 – TYPICAL APPLICATION

10/100

Ethernet

Monitor Decoder NW1

Access Point

(not included)

NW1

Client

(not included)

10/100

Ethernet

Video

Encoder Camera

LEGEND

WIRELESS

CAT5

COAX

ETHERNET

VIDEO

INS_NWKED_QS_REV– 05/20/13 PAGE 4TECH SUPPORT: 1.888.678.9427

Page 5

QUICK START USER GUIDE NWKED

Need Additional Assistance?

Visit our website http://www.comnet.net or contact Comnet tech support:

Tel: (203) 796-5300

Toll free: (888) 678-9427

Email: techsupport@comnet.net

Additional Technical support contact details can be found at:

http://www.comnet.net/services/technical-support.html

Or Visit our pre-sales design center:

http://www.comnet.net/services/design-center.html

Or our customer care:

http://www.comnet.net/services/customer-care.html

Additional Downloads

Datasheets, Installation manuals and other product documentation can be found at:

http://www.comnet.net/comnet-products/ethernet/wireless/

INS_NWKED_QS_REV– 05/20/13 PAGE 5