Comnet FDC8TM1 User Manual
Mechanical Installation Instructions
Figure 1: Dimensions are for a standard ComNet™one slot module.
FDC8TX1
.156 [3.96 mm]
.313 [7.95 mm]
Rack Module:
The unit is designed to be installed in the ComNet 19-inch (483-mm) EIA standard c
C1-EU, or the C1-CH. Follow these guidelines to install rack cards after performing module setup procedures.
Installation Considerations
This fiber-optic link is supplied as
tandalone/R
a S
Units should be installed in dry
locations protected from extremes
of temperature and humidity.
Standalone Module:
The unit is provided with a mounting
e with holes for two No.6 pan
t
pla
head screws (3-mm or 3.55-mm).
Attach the module to a solid piece
o
od using two No. 6 pan head
of w
wood screws with a minimum
penetration into the wood of
3/4 inch. (Screws not supplied)
See figure 1.
1. Determine where the module will be
installed
adequate space at both ends for
making the various cable
connections and for reading the
diagnostic LEDs.
2. Attach the module to a flat surface
using two mounting screws.
(Not Supplied)
ard-cage rack, the C1-US,
ack module.
and ensure that there is
,
C1-US,
CAUTION: Although the units are hot-swappable and may be installed without turning power off to the rack,
ComNet recommends that the power supply be turned off and that the rack power supply is disconnected
from any power source.Note: Remove electrical connector before installing in card cage rack.
CAUTION:Take care not to press on any of the LEDs.
C1-EU, or the C1-CH Card Cage Racks
e tha
1. Make sur
edge connector at the back of the card seats in the corresponding slot in the rack’s connector panel.
Seating may require thumb pressure on the top and bottom of the card’s front panel.
2. Tighten the two thumb scr
seated against the front of the rack.
t the card is oriented right side up, and slide it into the card guides in the rack until the
s on the card until the front panel of the card is
ew
INS_FDC8TX1_REVA
02/27/09
Page 1
FDC8TX1
INSTALLATION INSTRUCTIONS
Communication Networks
3 Corporate Drive • Danbury, CT 06810 • USA
Tel:203-796-5300 • Toll Free: 1-888-678-9427
www.comnet.net
8-CHANNEL
CONTACT CLOSURE TRANSMITTER
MULTIMODE
OR
SINGLE MODE
OPTICAL FIBER
LEDS: RED = “No Activity”
GRN = “Activity”
NOTE: RED DOES NOT MEAN “Error”
BLACK WITH WHITE STRIPE
BLACK
NOTE: Remove Electrical Connector for Rack Mount Units
WARNING: Unit is to be used with a Listed Class 2 or LPS power supply rated 9-12 VDC @ 1A.
WARNING: This unit should be installed in a restr
means of security. Access should be limited to service personnel who have been instructed about the reasons for the restrictions
to the location. Any and all precautions should be taken and controlled by the authority responsible for the location.
IMPORTANT SAFEGUARDS:
A) Ele
vated Operating Ambient - If installed in a closed or multi-unit rack assembly,
the op
erating ambient temperature of the rack environment may be greater than room ambient.
Therefore,consideration should be given to installing the equipment in an environment compatible with
the maximum ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installa
equired for safe operation of the equipment is not compromised.
r
tion of the equipment in a rack should be such that the amount of air flow
icted access location; available through the use of a lock and key or other
INS_FDC8TX1_REVA
02/27/09
Page 2
FDC8TX1
INSTALLATION INSTRUCTIONS
8-CHANNEL
CONTACT CLOSURE TRANSMITTER
•
•
TYPICAL
Communication Networks
3 Corporate Drive • Danbury, CT 06810 • USA
Tel:203-796-5300 • Toll Free: 1-888-678-9427
www.comnet.net
INS_FDC8TX1_REVA
02/27/09
Page 3
Mechanical Installation Instructions
Figure 1: Dimensions are for a standard ComNet™one slot module.
FDC8T232
.156 [3.96 mm]
.313 [7.95 mm]
Rack Module:
The unit is designed to be installed in the ComNet 19-inch (483-mm) EIA standar
C1-EU, or the C1-CH. Follow these guidelines to install rack cards after performing module setup procedures.
Installation Considerations
This fiber-optic link is supplied as
tandalone/R
a S
Units should be installed in dry
locations protected from extremes
of temperature and humidity.
Standalone Module:
The unit is provided with a mounting
e with holes f
plat
head screws (3-mm or 3.55-mm).
Attach the module to a solid piece
o
of wo
wood screws with a minimum
penetration into the wood of
3/4 inch. (Screws not supplied)
See figure 1.
1. Determine where the module will be
2. Attach the module to a flat surface
d using two No.6 pan head
installed
adequate space at both ends for
making the various cable
connections and for reading the
diagnostic LEDs.
using two mounting screws.
(Not Supplied)
d card-cage rack, the C1-US,
ack module.
or two No. 6 pan
and ensure that there is
,
C1-US,
CAUTION: Although the units are hot-swappable and may be installed without turning power off to the rack,
ComNet recommends that the power supply be turned off and that the rack power supply is disconnected
from any power source.Note: Remove electrical connector before installing in card cage rack.
CAUTION:Take care not to press on any of the LEDs.
C1-EU, or the C1-CH Card Cage Racks
e tha
1. Make sur
edge connector at the back of the card seats in the corresponding slot in the rack’s connector panel.
Seating may require thumb pressure on the top and bottom of the card’s front panel.
2. Tighten the two thumb scr
seated against the front of the rack.
t the card is oriented right side up, and slide it into the card guides in the rack until the
s on the card until the front panel of the card is
ew
INS_FDC8T232_REVA
02/27/09
Page 1
Loading...