INSTALLATION AND OPERATION MANUAL
CWFE100(X) PoE Series
10/100 MBPS ETHERNET FIBER OPTIC
MEDIA CONVERTER WITH 30W OR 60W POE+
This manual serves the following
ComNet Model Numbers:
CWFE1003POEM/M
CWFE1003POEMHO/M
CWFE1003POES/M
CWFE1003POESHO/M
CWFE1005POEM/M
CWFE1005POEMHO/M
CWFE1005POES/M
CWFE1005POESHO/M
CWFE1004APOEM/M
CWFE1004BPOEM/M
CWFE1004APOEMHO/M
CWFE1004BPOEMHO/M
CWFE1004APOES/M
CWFE1004BPOES/M
CWFE1004APOESHO/M
CWFE1004BPOESHO/M
CWFE1002APOEM/M
CWFE1002BPOEM/M
CWFE1002APOEMHO/M
CWFE1002BPOEMHO/M
CWFE1002APOES/M
CWFE1002BPOES/M
CWFE1002APOESHO/M
CWFE1002BPOESHO/M
CWFESFPMCPOE30/M
CWFESFPMCPOE60/M
The ComNet™ CWFE100(X)POE(M,S)/M Series 10/100Mbps Ethernet media converters
provide full-duplex fiber optic transmission of a single channel of 10/100BASE-T(X) data
through multimode or single mode optical fiber. Type ST, SC or SFP optics are available.
They provide full compliance with IEEE 802.3at as Power Sourcing Equipment (PSE),
with a maximum power of 30 watts in Mode A or Mode B, making them ideal for those
applications where the remote equipment draws significant power. A higher output 60
watt model is available.
Mode A and mode B are selected by the media converter automatically. The Ethernet
electrical interface auto-negotiates to either 10 or 100Mbps without the need for any
user selection, and the 100BASE-FX optical interface operates at 100Mbps.
LED indicators are provided for rapidly ascertaining the operating status of the
device. See Figure 9 on Page 6 for an explanation of the LED Indicators.
Packaged in a rugged, compact sized housing, these units are designed for shelf or
stand-alone mounting, or may be DIN-rail mounted by the addition of ComNet model
DINBKT2 Adaptor plate kit. See Figure A on Page 7 for mounting instructions.
See Figures 1 – 11 for complete installation instructions.
INS_CWFE100(X) POE SERIES_REVA
08/10/11
PAGE 1
INSTALLATION AND OPERATION MANUAL CWFE100(X) POE SERIES
FIGURE 1 – CWFE1003POE(M,S)-M MEDIA CONVERTER
CAT5e/6
BLACK
BLACK
W/WHITE STRIPE
Surface Mount
Power Supply: 48VDC @ 1.25A
FIGURE 2 – CWFE1003POE(M,S)-M MEDIA CONVERTER
REAR PANELFRONT PANEL
MULTIMODE OR
SINGLE MODE
OPTICAL FIBER
Tech SupporT: 1.888.678.9427
INS_CWFE100(X) POE SERIES_REVA
08/10/11
PAGE 2
INSTALLATION AND OPERATION MANUAL CWFE100(X) POE SERIES
TM
TM
FIGURE 3 – CWFE1003POE(M,S)HO-M MEDIA CONVERTER
CAT5e/6
BLACK
BLACK
W/WHITE STRIPE
Surface Mount
Power Supply: 48VDC @ 1.25A
FIGURE 4 – CWFE1003POE(M,S)HO-M MEDIA CONVERTER
REAR PANELFRONT PANEL
MULTIMODE OR
SINGLE MODE
OPTICAL FIBER
Tech SupporT: 1.888.678.9427
INS_CWFE100(X) POE SERIES_REVA
08/10/11
PAGE 3
INSTALLATION AND OPERATION MANUAL CWFE100(X) POE SERIES
TM
TM
FIGURE 5 – CWFE1005POE(M,S)-M MEDIA CONVERTER
CAT5e/6
BLACK
BLACK
W/WHITE STRIPE
Surface Mount
Power Supply: 48VDC @ 1.25A
FIGURE 6 – CWFE1005POE(M,S)-M MEDIA CONVERTER
REAR PANELFRONT PANEL
MULTIMODE OR
SINGLE MODE
OPTICAL FIBER
Tech SupporT: 1.888.678.9427
INS_CWFE100(X) POE SERIES_REVA
08/10/11
PAGE 4
INSTALLATION AND OPERATION MANUAL CWFE100(X) POE SERIES
TM
TM
FIGURE 7 – CWFE1005POE(M,S)HO-M MEDIA CONVERTER
CAT5e/6
BLACK
BLACK
W/WHITE STRIPE
Surface Mount
Power Supply: 48VDC @ 1.25A
FIGURE 8 – CWFE1005POE(M,S)HO-M MEDIA CONVERTER
REAR PANELFRONT PANEL
MULTIMODE OR
SINGLE MODE
OPTICAL FIBER
Tech SupporT: 1.888.678.9427
INS_CWFE100(X) POE SERIES_REVA
08/10/11
PAGE 5
INSTALLATION AND OPERATION MANUAL CWFE100(X) POE SERIES
FIGURE 9 – LED INDICATORS
LINK/ACT POE POWER
GREEN
Fiber interface linked
(when lit or flashing)
OFF
Fiber interface not
linked.
FIGURE 10 – POSSIBLE ETHERNET CONFIGURATION
Ethernet IEEE 802.3 Network Element determined by user.
30W PoE
Power is being
Unit powered up
supplied by unit
Power not supplied
Unit powered down
by unit.
(No PoE device)
CWFE1003POEM-M CWFE1003POEM-M
CAT5e/6 with
RJ-45 Connections
Remote Ethernet
IEEE802.3at PD
FIGURE 11 – POE PIN ASSIGNMENT
RJ-45 port supports IEEE802.3at
End-point: Positive (VCC+): RJ45 pin 1, 2 or 4, 5
Negative (VCC-): RJ45 pin 3, 6 or 7,8
Data: (1, 2, 3, 6)
CAT5e/6 with
RJ-45 Connections
Ethernet IEEE 802.3
Network Element
2 Multimode
Optical Fibers
Tech SupporT: 1.888.678.9427
INS_CWFE100(X) POE SERIES_REVA
08/10/11
PAGE 6
MECHANICAL INSTALLATION INSTRUCTIONS
INSTALLATION CONSIDERATIONS
This unit is supplied as a Standalone module. Units should be installed in
dry locations protected from extremes of temperature and humidity.
WARNING: Unit is to be used with a Listed Class 2 power supply.
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - Consideration should be given to installing
the equipment in an environment compatible with the maximum ambient
temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment should be such that
the amount of air flow required for safe operation of the equipment is not
compromised.
FIGURE A
Dimensions are for a small size ComNet™ surface mount module
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET
INS_CWFE100(X) POE SERIES_REVA
© 2013 Communications Networks Corporation. A ll Rights Reser ved. “ComNet ” and the “ComNe t Logo” are regis tered trademarks of Communic ation Networ ks, LLC.
08/10/11
PAGE 7
Loading...