INSTALLATION AND OPERATION MANUAL
CLSETUP
IP CAMERA SETUP AND POE TESTER
Important Safety Warning:
Read and keep these directions
Heed all warnings
Follow all instructions
Do not use this apparatus near water
Clean only with a dry cloth
Install in accordance with the manufacturer’s
instructions
This installation should be made by a qualified
service person and should conform to all local codes
See further safety instructions on Page 3
The ComNet™ CopperLine CLSETUP provides a simple way to setup and focus PoEpowered IP cameras, and is an ideal diagnostic tool for installers working with both
CCTV and IT PoE-based systems. The CLSETUP is compatible with IEEE 802.3af and
IEEE 802.3at PoE standards up to 30W.
See Figures 1 – 3 for complete installation details.
INS_CLSETUP_REV–
12/18/11
PAGE 1
INSTALLATION AND OPERATION MANUAL CLSETUP
FIGURE 1 – CLSETUP
CAT5
FIGURE 2 – CCLSETUP
RIGHT PANELLEFT PANEL
DIRECTIONS FOR ThE CLSETUP IP CamERa SETUP aND POE TESTER
Refer to Figure 3
• Disconnect the network cable
• Connect pigtail cable to the camera
• Connect network cable to “Network” connector
• Connect “Laptop” connector to your laptop using standard patch cable
• After the camera power is on the CLSETUP will display the PoE voltage applied to the camera
• Open your browser or viewing software to view the camera image for adjustments
FIGURE 3 – CLSETUP CONNECTIONS
CLSETUP
PoE Switch
PoE Camera
TECH SUPPORT: 1.888.678.9427
INS_CLSETUP_REV–
12/18/11
PAGE 2
MECHANICAL INSTALLATION INSTRUCTIONS
• Read and keep these directions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
• No objects filled with liquids, such as vases, shall be placed on the
equipment.
• DO NOT install the unit in a place where the operating ambient
temperature exceeds 75ºC.
• Make sure that the external power supply output voltage is in the
recommended range.
• Do not install near any heat sources such as radiators, heat registers, stoves
or other apparatus (including DVRs) that produce heat.
• Protect the power cord from being walked on or pinched, particularly at
the power source, convenience receptacles and the point where they exit
from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Unplug this apparatus during lightning storms or when unused for long
periods of time.
• Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as when a power
supply cord or plug is damaged, liquid has been spilled, objects have
fallen inside the apparatus, the apparatus has been exposed to rain or
moisture, do not operate normally or has been dropped.
WARNING: To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture. This apparatus shall not be
exposed to dripping or splashing and no objects filled with
liquids, such as vases shall be placed on the apparatus.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET
© 2012 Communications Ne tworks Cor poration. All Rights Reser ved. “ComNet ” and the “ComNet L ogo” are registered trademarks of C ommunication Networ ks, LLC.
INS_CLSETUP_REV–
12/18/11
PAGE 3
Loading...