CommScope PFU-P-C-O-060-02 Hardware Manual

Download

860634349

Two Port PoE Extender

Hardware Manual

Two Port PoE Extender Hardware Manual

Table of Contents

Electrical Safety.............................................................................................................. 1

For products that are rack mounted:...................................................................... 1

General................................................................................................................... 2

Sécurité Electrique.......................................................................................................... 3

Pour Les Produits Montés en Rack:....................................................................... 3

Dispositions Générales .......................................................................................... 4

Elektrische Sicherheit ..................................................................................................... 5

Für Geräte, die in einem Rack montiert werden:.................................................... 5

Allgemeines............................................................................................................ 6

CE NOTICE .................................................................................................................... 7

FCC NOTICE.................................................................................................................. 7

Return Product Procedure.............................................................................................. 8

Product user Guide......................................................................................................... 8

1 Introduction........................................................................................... 9

Why Protect Remotely Powered Circuits?...................................................................... 9

2 Package Contents............................................................................... 11

Two Port PoE Extender ................................................................................................ 11

Part Number......................................................................................................... 11

In the Box...................................................................................................................... 11

Also Required (Not Included)........................................................................................ 12

3 Installation........................................................................................... 13

Remove Heat Shield..................................................................................................... 13

Remove Seal Caps and Grommets.............................................................................. 13

Connect Ethernet Cables.............................................................................................. 15

Splitting the Powered Fiber Cable ................................................................................ 16

Cable Split Dimensions........................................................................................ 17

SFP Relationship to Ethernet ports............................................................................... 20

Setting the SFP Connection Speed.............................................................................. 21

Connecting the Powered Fiber Cable to the PoE Extender.......................................... 22

Connecting the Power Strands..................................................................................... 23

Connecting the fiber...................................................................................................... 24

Sealing the PoE Extender............................................................................................. 25

Installing the PoE Extender to Wall or Pole.................................................................. 26

Installing to a Wall................................................................................................ 26

Attaching an Earth Point....................................................................................... 27

Installing to a Pole................................................................................................ 28

Operating Temperature Advice..................................................................................... 29

4 Detailed Specifications....................................................................... 31

Two Port PoE Extender Hardware Manual

Safety Notice

In support of the EC directive 2006/95.EC, this notice contains safety information important for the correct installation and operation of this equipment.

Note, the term SELV (Safety Extra Low Voltage) used in this addendum is defined strictly in accordance with EN 60950

Electrical Safety

1. This equipment is intended for installation by trained service personnel only.

2. The safety requirements for Information Technology equipment is only valid if the building

installation is in compliance with relevant national or international safety standards and in accordance with good engineering practice.

3. Remove the DC supply from the supply cable at source before changing supply

connections to this product.

4. For safety requirements it is necessary to connect the earth point on the product to a

reliable earth. This is a discharge path in the event of surges or lightning events on the supply or Ethernet cables.

5. Unless otherwise specifically stated in the equipment installation manual, all data and

control ports are connected to ES1/SELV/NEC Class 2 conformant circuits inside the enclosure. To maintain all the ports on the equipment at SELV/NEC Class 2, it is essential that if any connection is made to any of these ports by other equipment, the other equipment must maintain its relevant port at ES1/SELV/NEC Class 2.

For products that are rack mounted:

6. For a closed or multi-unit rack assembly, the operating ambient temperature of the rack

environment may be greater than room ambient. Ensure that the equipment environmental temperature does not exceed the maximum ambient temperature specified by the manufacturer. Ensure that air flow required for safe operation of the equipment is not compromised.

7. Mounting of the equipment in the rack must not cause a topple or other mechanical

hazard.

8. Ensure that the accumulative power requirements of equipment installed in the rack do not

exceed the power supply wiring capacity of the rack. Use the equipment nameplate ratings to establish total requirements.

9. Reliable earthing of rack-mounted equipment should be maintained. Particular attention

should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

Two Port PoE Extender Hardware Manual

General

10. Unless otherwise stated in the equipment manual, there are no user serviceable parts

inside this equipment.

11. If this equipment has a laser, observe the precautions stated in the installation manual.

12. Ultimate disposal of this equipment must be carried out according to relevant national

laws.

13. The equipment should be installed by suitably trained personnel, and installation should

follow good working practice.

Two Port PoE Extender Hardware Manual

Consigne de sécurité

À l'appui de la directive de la Commission européenne n° 2006/95.EC, cet avis comporte des informations capitales pour procéder à une installation et à exploitation en bonne et due forme de cet équipement de sécurité.

À noter, le terme SELV (Safety Extra Low Voltage) utilisé dans le présent additif est défini le strict respect des exigences de la norme EN 60950.

Sécurité Electrique

1. Cet équipement doit être installé par du personnel d'entretien formé à la tâche.

2. Les exigences de sécurité équipements de technologies de l'information sont uniquement

valables si l'installation du bâtiment est conforme aux normes de sécurité nationales ou internationales pertinentes et aux bonnes pratiques d'ingénierie.

3. Veuillez débrancher l'alimentation en c.c. du câble d'alimentation à la source avant de

changer les raccordements d'alimentation à ce produit.

4. Pour les exigences de sécurité, il est nécessaire de connecter le point de mise à la terre au

produit via une terre fiable. Il s'agit d'un trajet de décharge prévu en cas de surtensions ou de phénomènes de foudre sur l'alimentation ou les câbles Ethernet.

5. Sauf indication contraire figurant dans le guide d'installation de l'équipement, l'ensemble

des données et ports de contrôle sont raccordés à des circuits conformes à la de classe 2 SELV/NEC/ES1 à l'intérieur de l'enceinte. Pour maintenir tous les ports de l'équipement en classe 2 SELV/NEC/ES1, il est indispensable qu'en cas de raccordement établi vers l'un quelconque de ces ports par tout autre équipement, ce dernier puisse maintenir son port correspondant en classe 2 SELV/NEC/ES1.

Pour Les Produits Montés en Rack:

6. Pour un rack fermé ou dispositif à plusieurs racks, la température ambiante de

fonctionnement de l'environnement du rack peut être supérieure à celle ce la température ambiante. Assurez-vous que la température de l'environnement de l'équipement ne soit pas supérieure à la température ambiante maximale indiquée par le fabricant. Veiller à ce que le débit d'air nécessaire au bon fonctionnement de l'équipement ne soit pas compromis.

7. Le montage du matériel dans le rack ne doit pas provoquer de basculement ni aucun

autre danger mécanique.

8. Veiller à ce que les exigences d'alimentation cumulées de l'équipement installé dans le

rack ne soient pas supérieures à la capacité de câblage d'alimentation du rack. Utilisez les cotes de la plaque signalétique de l'équipement pour mettre en place toutes les exigences.

9. Il convient de maintenir une mise à la terre fiable d'équipement monté en rack. Il convient

de faire particulièrement attention aux raccordements d'alimentation autres que ceux directement en contact avec le circuit de dérivation (p. ex., utiliser des bars d'alimentation).

Two Port PoE Extender Hardware Manual

Dispositions Générales

10. Sauf indication contraire figurant dans le manuel de l'équipement, ce dernier ne

comporte aucune pièce susceptible de réparation par l'utilisateur de l'équipement.

11. Si cet équipement comporte un dispositif laser, veuillez respecter les précautions

indiquées à cet égard dans le guide d'installation.

12. La suppression définitive de cet équipement devra être effectuée conformément aux lois

nationales pertinentes.

13. L'équipement doit être installé par du personnel parfaitement qualifié, et l'installation

devra être conforme aux bonnes pratiques.

Two Port PoE Extender Hardware Manual

Sicherheitshinweis

Im Rahmen der EU-Richtlinie 2006/95.EC enthält dieser Hinweis wichtige Sicherheitsinformationen für die korrekte Installation und den Betrieb dieser Geräte.

Beachten Sie, dass der hier verwendete Begriff SELV (Safety Extra Low Voltage Schutzkleinspannung) streng nach EN 60950 definiert ist.

Elektrische Sicherheit

1. Dieses Gerät ist ausschließlich für den Einbau durch geschultes Servicepersonal

vorgesehen.

2. Diese Sicherheitsanforderungen für IT-Ausrüstung sind nur dann gültig, wenn die

Gebäudeinstallation den einschlägigen nationalen und internationalen Sicherheitsstandards sowie den allgemein anerkannten Regeln der Technik entspricht.

3. Vor Änderung der Versorgungsanschlüsse dieses Geräts muss die DC-Stromversorgung zu

den Versorgungskabeln getrennt werden.

4. Aus Sicherheitsgründen muss der Erdungspunkt des Produktes mit einer zuverlässigen

Erde verbunden werden. Diese dient als Entladungsweg bei Überspannungen oder Blitzereignissen, die sich auf Versorgungs- oder Ethernet-Kabel auswirken.

5. Sofern im Installationshandbuch nicht ausdrücklich anders vermerkt, sind alle

Datenschnittstellen und Steueranschlüsse mit ES1/SELV/NEC Class 2 konformen Schaltkreisen im Inneren des Gehäuses verbunden. Damit alle Ports des Geräts mit ES1/ SELV/NEC Class 2 konform bleiben, ist es wichtig, dass die Ports verbundener Geräte ebenfalls ES1/SELV/NEC Class 2 entsprechen.

Für Geräte, die in einem Rack montiert werden:

6. Bei Einbau in eine geschlossene oder aus mehreren Geräten bestehende Rack-Einheit

kann die Betriebsumgebungstemperatur im Rack höher als die Raumtemperatur sein. Stellen Sie sicher, dass die Umgebungstemperatur der Geräte die vom Hersteller angegebene maximale Umgebungstemperatur nicht überschreitet. Achten Sie darauf, dass der für den sicheren Betrieb des Geräts erforderliche Luftstrom nicht beeinträchtigt wird.

7. Bei Montage der Geräte in einem Rack darf keine Gefahr durch Kippen oder andere

mechanische Einflüsse entstehen.

8. Stellen Sie sicher, dass der Gesamtleistungsbedarf der im Rack installierten Geräte die

Stromversorgungskapazität des Racks nicht überschreitet. Nutzen Sie die Angaben auf den Typenschildern, um die Gesamtlast zu ermitteln.

9. Es muss eine zuverlässige Erdung der Rack-Geräte gegeben sein. Besondere

Aufmerksamkeit gilt dabei der indirekten Anbindung an Zweigstromkreise (z. B. Verwendung von Mehrfachsteckerleisten).

Two Port PoE Extender Hardware Manual

Allgemeines

10. Sofern nicht anders im Gerätehandbuch angegeben, enthält dieses Gerät keine zu

wartenden Teile.

11. Wenn dieses Gerät mit einem Laser ausgestattet ist, beachten Sie die in der

Installationsanleitung angegebenen Vorsichtsmaßnahmen.

12. Die Entsorgung dieses Geräts muss nach den einschlägigen nationalen Rechtsvorschriften

erfolgen.

13. Das Gerät muss durch entsprechend geschultes Personal installiert werden. Bei der

Installation ist auf gute Arbeitspraxis zu achten.

Two Port PoE Extender Hardware Manual

CE NOTICE

Note: This is a class B product.

FCC NOTICE

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules.

Modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment under FCC rules.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la class B est conforme a la norme ICES-003 du Canada

Two Port PoE Extender Hardware Manual

Return Product Procedure

If the unit is found to be defective please contact Technical Support via www.commscope.com/

SupportCenter/TechnicalSupport.aspx

Product user Guide

This document details the physical features of the Two Port PoE Extender.

Two Port PoE Extender Hardware Manual

1. Introduction

The PoE Extender is a component of CommScope®’s powered fiber cable system, a hybrid optical fiber/copper cable system for remote powering of network access devices. It is designed to simply and easily function with the powered fiber cable system to extend the distance of PoE (Power over Ethernet) enabled devices. The PoE Extender encompasses four primary elements:

1. Environmentally sealed closure

2. Electrical power management

3. Circuit protection electronics

4. Optical to electrical Media Conversion

When coupled with any standard NEC Class II 48V DC power supply CommScope’s Powered Fiber Cable system can power and communicate with PoE standard devices at far greater distances than "category style" copper cabling systems which are typically limited to 90 meters, and still meet NEC Class II and SELV standards, eliminating the need for qualified electricians during installation.

The PoE Extender also contains circuit protection and DC/DC conversion electronics which automatically condition electrical voltage to the correct level needed for PoE input to the device under load (such as a small cell, high definition security camera, Wi-Fi hot spot, etc).

Why Protect Remotely Powered Circuits?

Long length DC low voltage electrical systems are at increased risk of:

• AC cross from high voltage cables

• Higher current in the event of a short circuit

• Strong electrical surges due to lightning strikes or other EM events in close vicinity

The PoE Extender provides two levels of electrical protection:

5. Primary Protection:

• Metal oxide varistors - operates for slower surges as well as fast surges

• Protects both differential and common mode

• MOV components rated to 4.5kA

6. Secondary Protection:

• Transient voltage suppressors - works at relatively low/slow surges, adds an extra

layer of protection against voltage spikes

• Protects differential mode only

• Prevents the voltage from rising above 80-100V

Two Port PoE Extender Hardware Manual

Additional protection elements include:

• Cross-polarity protection to simplify installation - the circuit will work regardless of the

input polarity

• AC cross protection:

• 4A non replaceable fuses

• No exposed high voltage pads

• High power inductors used as coordinating elements to maximize energy efficiency

• Sealed enclosure for environmental protection

Two Port PoE Extender Hardware Manual

2. Package Contents

Two Port PoE Extender

Part Number

The part number for the Two Port PoE Extender is PFU-P-C-O-060-02

In the Box

The PoE Extender is supplied ready for cable installation with the solar shield attached.

Two Port PoE Extender Hardware Manual

Also Required (Not Included)

• 3mm and 4mm Allen key

• 2 x Standard 100Base-X or1000Base-X SFP transceiver (Singlemode or Multimode)

• 25mm Torque or adjustable spanner/wrench

• 30mm Torque or adjustable spanner/wrench

• Posidriv screwdriver

• Silicone grease

• Loctite 222

• Knife for splitting the fiber cable

• 12 AWG or 2mm diameter wire stripper for 12 AWG cable

• 16 AWG or 1.2mm wire diameter stripper for the 16 AWG cable

• Fastenings for wall/pole mounting

Two Port PoE Extender Hardware Manual

3. Installation

Installation of the PoE Extender should be completed in the following order.

Remove Heat Shield

Remove the 4 bolts attaching the heat shield to the PoE Extender with a 3mm Allen key. Slide the heat shield off the retaining lugs and put to one side.

Remove Seal Caps and Grommets

Unscrew the caps and then remove the grommets from the 3 pass through connectors.

Note: Do not unscrew any of the pass throughs from the PoE Extender. These have been

factory fitted and sealed to the correct torque setting.

Two Port PoE Extender Hardware Manual

Connect Ethernet Cables

CommScope recommend installing the cables in the following order, when facing the connector pass throughs:

1. Left hand ethernet connection

2. Right hand ethernet connection

3. Fiber and power cable connection

4. Thread the seal cap and ethernet grommet on to the cable as below.

5. Connect one of the RJ45 to the PoE Extender to the left hand pass through, with the lock

clip facing upwards, as below. Note the Ethernet cable is still loose in the grommet.

Note: Connection from the PoE Extender to the Customer’s equipment should be via a Cat 5E /

Cat 6 screened (STP) cable.

Note: If using a pre-terminated ethernet cable it may be necessary to remove the boot. Some

connectors may require cutting the cable and re-terminating after threading the cable through the grommet.

Two Port PoE Extender Hardware Manual

6. Tighten the cap against the pass through. The recommended torque is 2.50Nm (22.1in

lbf).

7. Note that the grommet is now tightened against the cable.

8. Repeat steps 1-7 for the right hand ethernet connection.

Splitting the Powered Fiber Cable

The CommScope Powered Fiber Cable consists of 2 copper power threads and a third containing the fiber threads. You need to separate the three cores to allow the power to be connected to the screw terminals, and the fiber thread to be connected to a fiber terminal, which is then inserted in to the SFP.

The Powered Fiber Cable is design to access using only a typical pair of wire strippers and, optionally, a wire cutter or snip. To split the cable successfully, follow this process:

Two Port PoE Extender Hardware Manual

Cable Split Dimensions

Figure: 3.1 Cable Split Dimensions

75cm

23cm

24c

Two Port PoE Extender Hardware Manual

1. Snip the cable end at the indentations in the cable jacket between the center fiber element

and the two outer conductor elements.

Two Port PoE Extender Hardware Manual

2. Peel one conductor side away to the desired length (75cm) by hand.

Two Port PoE Extender Hardware Manual

3. While holding the center fiber element in as straight a line as possible, peel the second

conductor element away to the desired length.

4. For the 12 AWG cable, use a proper 12 AWG or 2MM diameter wire stripper. For the

16AWG, use a 16 AWG or 1.2mm wire diameter stripper.

5. Use tape or heat shrink to prevent the cables splitting further than the required length.

6. Ensure the cables are smooth to prevent water ingress issues through the grommet.

7. Strip the two copper elements to an appropriate length, just as accessing any copper

cable.

8. For the center fiber element, simply place the strippers at the desired strip location, close

the wire strippers fully once, then open. Now, by hand you may pull the center element jacket off, revealing the aramid and optical fibers.

9. Remove excess aramid as desired for termination.

SFP Relationship to Ethernet ports

The SFP relationship to the Ethernet ports is as follows:

• If both SFPs are connected, the bottom SFP data goes via Ethernet port one (nearest the

SFPs). The top SFP data goes via Ethernet port two.

Two Port PoE Extender Hardware Manual

• If only one SFP is connected the data goes via both Ethernet ports

Setting the SFP Connection Speed

By default both the PoE Extender SFP ports are configured for 1Gbit/s. If required you can configure one or both to 100Mbit/s.

To change the default configuration:

1. Remove the white fiber splice tray for the PoE Extender.

Two Port PoE Extender Hardware Manual

2. Locate the jumpers on the board (in this illustration they are red, production color may

differ)

3. To change the setting for one or both of the SFPs, see the illustration below (as facing the

board in the above images):

4. Re-install the fiber tray.

Connecting the Powered Fiber Cable to the PoE Extender

1. Thread the strands through the cap, then thread the strands through the supplied grommet.

Use some silicone grease on the grommet, which helps pulling the strands through the

Two Port PoE Extender Hardware Manual

grommet, and provides a seal against water ingress.

2. When threading the cable through the pass through, ensure the fiber strand is uppermost

when pushing the grommet in to the pass through. Use tape or heat shrink to prevent the cables splitting further than the required length.

3. Using the Torque wrench, tighten the screw cap on the pass through. Tighten to torque

1.75Nm (15.5 in lbf).

Connecting the Power Strands

1. Cut the two power strands to length (approximately 14cm). Remove 5mm of sheath from

the two cables.

2. For the 12 AWG cable, use a proper 12 AWG or 2MM diameter wire stripper. For the

16AWG, use a 16 AWG or 1.2mm wire diameter stripper.

3. Use tape or heat shrink to prevent the cables splitting further than the required length.

Thread the two cables in to the power connectors and tighten the screws.

Note: Due to the cross-polarity protection, the circuit will work regardless of the input polarity.

Two Port PoE Extender Hardware Manual

Connecting the fiber

1. Insert the SFPs in place.

2. Remove the sheath from the fibers, Allowing 14cm of sheath from the initial cable split, as

in Figure 3.1. Place the strippers at the desired strip location, close the wire strippers fully once, then open. Now, by hand you may pull the center element jacket off, revealing the aramid and optical fibers.

3. Remove excess aramid as desired for termination.This allows the sheath to rest on the

beginning of the splice tray.

4. The fibers should wrap around the splice tray twice.

5. The splice to the fiber connectors should sit in the splice island in the tray as below.

Note: Insert the bottom SFP in place first. This SFP is inserted upside down. The SFPs should only

be inserted or removed with the power off.

Two Port PoE Extender Hardware Manual

6. The fiber LC/UPC pigtails should wrap around the splice tray once, then connect to the

SFPs as below.

Sealing the PoE Extender

1. Ensure the supplied seal ring is seated in the channel of the PoE Extender and all cables

are secured.

2. Apply Loctite 222 to all lid bolts

Note: Field installable connectors such as LightCrimp Plus can be used. A clip to connect two LC

simplex to one LC duplex is recommended.

Two Port PoE Extender Hardware Manual

3. Put the lid back in place.

4. Tighten the screws to torque 2.5Nm (22.1 in lbf). It is recommended that you tighten the

screws in the opposite corners first (for example, bottom left, then top right, bottom right then top left).

Installing the PoE Extender to Wall or Pole

Installing to a Wall

The PoE extender has 4 holes on the exterior of the device for attaching to a wall or flat surface.

Two Port PoE Extender Hardware Manual

PoE wall mounted with solar shield

Attaching an Earth Point

To ensure reliable operation, the PoE Extender should be earthed. Make connections from the enclosure earth point using the M5 bolt and washer provided:

1. A minimum 16AWG bonding connection from the PoE Extender to the Customer’s equip-

ment earth terminal

2. A minimum 16AWG bonding connection from the PoE Extender to a reliable earth

(ground) point.

Figure: 3.1 PoE Extender Earth Point

Two Port PoE Extender Hardware Manual

Installing to a Pole

The PoE extender has 4 holes on the raised sections of the underneath of the device for attaching to a pole via fastenings such as jubilee clips.

PoE pole mounted with solar shield

Two Port PoE Extender Hardware Manual

Attaching an Earth Point

Attach your earth connection to the earth point below.

Operating Temperature Advice

At the top of the Two Port PoE Extender’s operating temperature range, the physical temperature of the PoE Extender may exceed 70ºC. Ensure the supplied solar shield is in place for protection. See Table 4.2 on page 31 for operating temperature details.

Two Port PoE Extender Hardware Manual

4. Detailed Specifications

Table 4.1: Part Numbers

Version Catalogue Number

Two Port PoE Extender PFU-P-C-O-060-02

Table 4.2: Climatic Performance

Item Specification

Storage Temperature

-40

C to +70ºC

Installation Temperature

-5

C to +45ºC

Operating Temperature

-40

C to +65ºC

65°C assumes 45°C ambient air temperature, plus 20°C sun loading.

Table 4.3: Physical Dimensions

Item Specification

Dimensions including solar shield 283mm x 225mm x 77mm Weight 3.8kg

Two Port PoE Extender Hardware Manual

Maximum Output 30W at the PoE Extender to permit 25.5W with 90m of Cat 6 cable.

NEC Class 2 requires a power supply unit (PSU) limited to less than 60V DC. In practice, some commercial 48V power supplies may be configured to output from 48V up to about 57V.

A range of PSU voltage outputs is represented, along with the two Powered Fiber Cable copper gauge options, with supported maximum distances in meters.

Table 4.4: Electric Transmission

Input Voltage

Cable Gauge (AWG)

Lmax (m)

(PoE+/PoE+)

Lmax (m)

(PoE/PoE+)

Lmax (m) (PoE/PoE)

Lmax (m)

(PoE+)

Lmax

(m) (PoE)

Maximum (57V) 12 650 1120 1570 1595 2630

Maximum 16 255 445 620 630 1040

Nominal (48V) 12 460 795 1100 1120 1840

Nominal 16 180 315 435 440 725

Minimum (40.5V) 12 330 555 770 780 1285

Minimum 16 130 220 305 310 510

Note: PoE standard IEEE 802.3 af (IEEE 802.3at type 1) assumes 12.95W power

consumption. PoE+ standard (IEEE 802.3at type 2) assumes 25.5W.

Two Port PoE Extender Hardware Manual

Table 4.5: EMI/C & Safety

Item Specification

EMC Emissions CISPR 22/FCC CFR 47 Part 15/ICES-003

EN 55032:2015

Immunity EN300386/ICES-003

EN 55024:2010 + A1:2015 ITU-T K.45

Safety IEC 60950-22:2006

IEC 62368-1:2014

Compliance

CE/FCC/CSA/RCM SELV NEC Class 2 input.

Environmental

ETSI EN 300 019-1-4 V2.3.1 (2013-08) Class 4.1E EN 60068-2-52:1996 REACH SVHC RoHS2 2011/65/EU EN 60529:1992 + A2:2013 (IP68) NEMA 6P

Table 4.6: Communications

Item Specification

Optical Input Accepts all MSA compliant 100Base-X and

1000Base-X SFP transceivers Optical Input Singlemode ITU-T G657.A2 Optical Input 50um Multimode OM3 or OM4 RJ45 Connector Output Half and Full Duplex Modes Supported.

10/100/1000Mb Ethernet

Two Port PoE Extender Hardware Manual

© 2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. All other trademarks are property of their respective owners. For planning purposes only. CommScope reserves the right to modify the specifications or product without notice. This document is not intended to modify or supplement any specifications or warranties relating to CommScope products or services.

Table 4.7: Supported Fiber Cable Types

Catalogue Number Cable

PFC-S02L12 PFC,Singlemode,2F,I/O,12AWG PFC-S02L16 PFC,Singlemode,2F,I/O,16AWG PFC-S02O12 PFC,Singlemode,2F,Outdoor,12AWG PFC-S02O16 PFC,Singlemode,2F,Outdoor,16AWG PFC-S04L12 PFC,Singlemode,4F,I/O,12AWG PFC-S04L16 PFC,Singlemode,4F,I/O,16AWG PFC-S04O12 PFC,Singlemode,4F,Outdoor,12AWG PFC-S04O16 PFC,Singlemode,4F,Outdoor,16AWG PFC-S12L12 PFC,Singlemode,12F,I/O,12AWG PFC-S12L16 PFC,Singlemode,12F,I/O,16AWG PFC-S12O12 PFC,Singlemode,12F,Outdoor,12AWG PFC-S12O16 PFC,Singlemode,12F,Outdoor,16AWG PFC-302L12 PFC,OM3,2F,I/O,12AWG PFC-302L16 PFC,OM3,2F,I/O,16AWG PFC-302O12 PFC,OM3,2F,Outdoor,12AWG PFC-302O16 PFC,OM3,2F,Outdoor,16AWG PFC-304L12 PFC,OM3,4F,I/O,12AWG PFC-304L16 PFC,OM3,4F,I/O,16AWG PFC-304O12 PFC,OM3,4F,Outdoor,12AWG PFC-304O16 PFC,OM3,4F,Outdoor,16AWG

CommScope PFU-P-C-O-060-02 Hardware Manual

Specifications and Main Features

Frequently Asked Questions

User Manual