Comet 33206 Instruction Manual

Page 1
6+
ITEM NO: 33206
INSTRUCTION MANUAL
WARNING:
Incorrectly storing this RC helicopter may bend and/or warp the rotor blades. Bent and/or warped rotor blades may make it fly improperly.
Page 2
CHARGING THE UFO BALL
USB CHARGER LED LIGHT INDICATOR
No Light
Charged
Red Light
USB charger is connected to UFO Ball and is charging.
Charging time 30-60 minutes.
Connect the UFO Ball to the included USB charger then plug the USB plug into any powered USB por t.
When the UFO Ball has trouble hovering you may need to charge the internal battery pack. Turn off the UFO Ball and wait 5-10 minutes to cool before charging.
UFO Ball Body
Rotor Blade
Stabilizer Bar
Bottom View
IR Sensor
IR Emitter
Charging Port
Power Switch
UFO BALL OVERVIEW
Front
Back
Please Note: The USB charger light will turn on when plugged in and connected to the UFO Ball to indicate charging. Once the battery is fully charged the light will turn off. Disconnect charger promptly afterward to avoid damage to the battery.
Page 3
FLYING THE UFO BALL
REPLACING ROTOR BLADES
The UFO Ball should only be used indoors and away from people, pets and objects.
1. Flip the power switch on the UFO Ball to turn it on. A blue LED light will indicate that the power is on and ready to fly.
2. Hold the UFO Ball with your fingers out of the way of the rotor blades. After 3 seconds the rotor blades will start spinning. Let
go of the UFO Ball and keep your hand under it to keep it in the air as it floats up and down sensing any object underneath it.
3. Move your hand closer to the UFO Ball and it will fly up. Lower your hand and it will fly lower. If you put your hand down it will sense the floor or other objects and hover just above, like it does with your hand.
4. To turn off, quickly and carefully grab the ball and flip the power switch to off. To easily slow down and stop the UFO Ball, aim any household infrared remote* at the UFO Ball and press the power button. The UFO Ball will slowly descend, land and turn off the rotors. Promptly pick it up and flip the power switch off.
*Not all Infrared Remotes will work. Initially test a new remote with the UFO Ball in your hand prior to letting go for flight.
The rotors may become damaged during a collision. The UFO Ball comes with 2 spare rotors. Please replace damaged rotors immediately. The UFO Ball comes with 1 A rotor and 1 B rotor. The A and B rotors must be installed on specific locations on the UFO Ball for it to fly properly. Check the bottom of each rotor to see if it’s labeled either A or B. Match the new rotor to the damaged one and replace.
No tools are needed to replace the rotors. Follow the steps below to replace the damaged rotor.
1. Pull the damaged rotor of f to the side and unhook the rotor as shown.
2. Push the new rotor into place until it clicks in place and moves freely.
Page 4
TROUBLESHOOTING
SAFETY PRECAUTIONS
• Never use outdoors.
• Keep away from faces and animals.
• Do not launch at people or animals.
• Use the charger included in this package to recharge the battery in the UFO Ball.
• Keep fingers away from the UFO Ball while in use.
• Make sure people around you are aware you are playing with the UFO Ball.
• Do not fly the UFO Ball near overhead cables, trees, buildings, or any other obstructions.
• Always turn off when not in use.
• This user manual should be kept for future reference.
• This product contains electric components, please do not submerge in water or use in a wet environment.
Website: www.worldtechtoys.com Email: customerserv@worldtechtoys.com Phone: (877) 498-8697 Monday - Friday / 8:00AM - 5:00PM / Pacific Time
MADE I N CHINA
SPECIFICATIONS,
COLORS AND CONTENT
MAY VARY FROM ILLUSTRATIONS
Rotor blades do not move
Stops operating during flight
The UFO Ball is shaking
when flying
Experience loss
of control
- ON/OFF switch is off. - Weak battery.
- Weak Battery.
- Damaged Rotor Blades.
- Set the switch to ON. - Charge the Battery.
- Charge the Battery.
- Replace the damaged rotor blades.
- Fly the UFO Ball in a different area.
- Turn off the bright lights.
- Another Infrared RC device is using the same channel.
- Bright lighting is effecting the IR transmitter.
PROBLEM CAUSE SOLUTION
Ufo Ball is manufactured by World Tech Toys., under various licenses from Rehco, L.L.C. Ufo Ball is subject to patents under license from Rehco, L.L.C., including US Pat. No. 7,100,866 and US Pat. No. 9,636,597 and additional US and foreign patents pending.
Loading...