Comelit ANPR922M3M User Manual

3MP LPR IP CAMERA

ART. ANPR922M3M

Please read this manual thoroughly before use and keep it for future reference

ANPR922M3M user manual – 1st ed.

Contents

1. Webpage Overview ............................................................................................................. 4

2. Web Log in ........................................................................................................................... 4

3. Preview ................................................................................................................................. 5

3.1 Main stream and Sub-stream Switching ................................................................... 5

3.2 Prompt Alarm .............................................................................................................. 5

3.3 Timing Recording ....................................................................................................... 6

3.4 Recording Video Manually ......................................................................................... 6

3.5 Switching Picture Ratio .............................................................................................. 6

3.6 Audio Function ............................................................................................................ 7

3.7 Snapshot Function ..................................................................................................... 7

3.8 Showing Sidebar Function......................................................................................... 7

3.9 OSD Function ............................................................................................................. 7

3.10 Image Parameter Adjustment Setting .................................................................... 8

3.11 Watermark Setting ................................................................................................... 9

3.12 Video Reconnection ................................................................................................10

3.13 Video Full Screen Display ......................................................................................10

4. Video Playback ...................................................................................................................11

4.1 Local Video Playback ................................................................................................11

4.2 Remote Recording Playback ....................................................................................14

5. Checking Pictures ...............................................................................................................17

5.1. Checking Pictures ....................................................................................................17

6. Setting ..................................................................................................................................18

6.1. Local parameter .......................................................................................................19

6.1.1. Path configuration .........................................................................................19

6.1.2. Local recording plan ......................................................................................20

6.2 Remote Configuration ...............................................................................................21

6.2.1 Basic Information ............................................................................................22

6.2.1.1 Basic setting .........................................................................................22

6.2.1.2 Video Setting ........................................................................................23

6.2.1.3: Remote Recording Plan .....................................................................24

6.2.1.4 SD card management .........................................................................25

6.2.1.5 Motion Detection Setting .....................................................................26

6.2.1.6 Snapshot setting ..................................................................................29

6.2.1.7.Alarmset ...............................................................................................30

6.2.1.8 Serial set...............................................................................................31

6.2.2 Network set .....................................................................................................32

6.2.2.1 Network parameters ...........................................................................32

6.2.2.2 PPPOE Setting ....................................................................................34

6.2.2.3 DDNS Setting .......................................................................................34

6.2.2.4 Email Set ..............................................................................................35

6.2.2.5 FTP Set ................................................................................................36

6.2.3 Milestone Server Set ......................................................................................37

2

ANPR922M3M user manual – 1st ed.

6.2.3.1 Milestone Server Set ...........................................................................37

6.2.4 Event Management ........................................................................................38

6.2.5 User Management ..........................................................................................38

6.2.6 System Maintenance ......................................................................................38

7. Operation Environment .......................................................................................................39

7.1 Operation System......................................................................................................39

7.2 Browser Compatibility ...............................................................................................39

3

Statement

These instructions are for guidance only. Detailed features are in accordance with

the product.

The instructions may include some technical inaccuracies or typographical error thought

it is prepared with our every effort.

The product or procedures described in the instruction may be changed or updated at

any time without advance notice.
Screenshots used in the instruction are only for indications and explanations.

For any doubts or to request documents about latest procedures and complementary
notes, please consult with the after-sales service department.

ANPR922M3M user manual – 1st ed.

7. Webpage Overview

Network camera web page is mainly divided into four parts: preview (picture parameter,
adjustment, silk setting), playback (local video playback and remote video playback),
checking pictures (scratched picture, motion detection, detector alarming), configuration.

(Note: to enable this feature, verify if your IPC model have checking picture function)

2. Web Log in

Log in “Internet Explorer” (support Internet Explorer 7.0, Internet Explorer 8.0,
Internet Explorer 9.0, Internet Explorer 10) and input the default address

http://192.168.0.66 (the default port for this address is 80, if you change the web porta as
81, you should add colon, then port no., for example, http://192.168.0.66:81). As shown
on picture: 2-1, you can access the login page of IPC and can switch language. Input the
user name and password, then click [Login] button to see the preview page.

Default User Name and Password to login: User Name: admin; Password: admin. This
is the user name and password for administrator, who has the highest administrative
authority, including the authority of setting the user name and password, as well as the
administration authority for the regular users and maintenance personnel.

(Picture: 2-1)

4

ANPR922M3M user manual – 1st ed.

3. Preview

3.1 Main stream and Sub-stream Switching

1.Main stream and sub-stream switching. As is shown in picture 3-1 in the red region,
click button to switch into main stream and click button to

switch into sub-stream.

(Picture: 3-1)

3.2 Prompt Alarm

1. Prompt alarm. As is shown picture 3-2 in the red region, set the region and time for
motion detection as well as the time for detector alarming, prompt alarm will happen
in the fitful time after alarming issues are activated. Detector alarming and motion

detection have three states for each, means detector alarming is not set,
means detector alarming has been set. when this 5 sas5o55 flickering, it means
detector alarming is going on; means motion detection is not set, means

motion detection has been set. when this button twinkles, it means motion
detection is alarming.
(Note: to enable this feature, verify if your IPC model have alarm/motion functions)

5

ANPR922M3M user manual – 1st ed.

(Picture: 3-2)

3.3 Timing Recording

7. Timing recording. As is shown in picture 3-2, set the remote video

recording plan in [Configuration]  [Remote Configuration]  [Basic Info].
means remote video is not planned, means time video recording is going on.

(Note: to enable this feature, verify if your IPC model have timing recording function)

3.4 Recording Video Manually

1. Recording Video Manually. As is shown in picture 3-2, click the button for manual
video recording. The button will turn , which means manual video recording is going
on, the files for the video will be saved in the saving path. You can set the saving path in
[Configuration]  [Local Configuration]  [Saving Path Setting]

3.5 Switching Picture Ratio

1. Switching Picture Ratio. As is shown in picture 3-2, click the button in red
region. The image will switch between two states: ratio and full. Ratio means
image will show in ratio of 16:9 or 4:3, full means image will occupy the whole
page to satisfy different resolution monitor.

3.6 Audio Function

1. Audio Function. As is shown in picture 3-2, is the audio button, means on
audio is on.

6

ANPR922M3M user manual – 1st ed.

After clicking audio button, it support talk back, you only need to connect with microphone
and loudspeaker for IPC as well as for PC.
(Note: to enable this feature, verify if your IPC model have audio function)

3.7 Snapshot Function

1.Snapshot Function. As is shown in picture 3-2, click the button for manual

snapshot. When you click this button, the current video image will be captured as a
picture and will be saved in the saving path. You can set the saving path in
[Configuration]  [ Local Configuration ]  [ Path Configuration].

3.8 Showing Sidebar Function

1.Showing sidebar function operation. As is shown in picture 3-2, after clicking the

button , to show sidebar, and to hide sidebar after clicking .

3.9 OSD Function

1.OSD Function. See picture 3-3 in the red region for OSD function operation. Click

the button , the subtitle will show on video and you can adjust the subtitle.

2. means up toward and the value on the left side is chosen, but will not change

the meaning of right side. means down toward and the value on the left side is
chosen, but will not change the meaning of right side. means right toward, and
will change the value of right side after clicking this button based on the left side
value. means left toward and change the value of right side after clicking this
button based on the left side value. button. When the right side value has “#”,
you can click [OK] button into submenu of this value and you can set this value in the
submenu.

(Note: PTZ function operation is similar to OSD function operation. To enable this feature,
verify if your IPC model have OSD and/or PTZ function)

7

ANPR922M3M user manual – 1st ed.

(Picture: 3-3)

3.10 Image Parameter Adjustment Setting

1. Image parameter adjustment setting, as is shown in picture 3-4, red area.

drag the horizontal sliders below Sharpness, corresponding value

will appear in the text box and the video image will change correspondingly.

drag the horizontal sliders below Brightness, corresponding value

will appear in the text box and the video image will change correspondingly.

drag the horizontal sliders below Contrast, corresponding value will

appear in the text box and the video image will change correspondingly.

drag the horizontal sliders below Saturation, corresponding value

will appear in the text box and the video image will change correspondingly.

Mirroring function has left and right option.

Turn function has up and down option.

Noise reduction function has disable and able option.

WDR function has disable and able option.

8

ANPR922M3M user manual – 1st ed.

Day/Night function has color, black and white, external

synchronization option.

Flashing function has outdoor, 50HZ, 60HZ option.

(Note: to enable the features, verify if your IPC model have all the functions)

(Picture: 3-4)

3.11 Watermark Setting

1. Watermark setting as shown in picture 3-5, red area.
channel name can be set.

User-defined information can be set.

You can display or hide the time, frame rate, channel name,

user-defined information. Once check and click [Save] button, the page will be
prompted to [Save Success] words, after successfully saved, the video image will
display modified channel name, frame rate, channel name, user-defined information.

9

ANPR922M3M user manual – 1st ed.

(Picture: 3-5)

3.12 Video Reconnection

7. Video Reconnection: You do not need to refresh the web page because you can re-

get the video after network goes back to normal working. Meanwhile when the IPC
has an SD card even in network off condition, video will be recorded in the IPC.

3.13 Video Full Screen Display

1. Video Full Screen Display. As shown in picture 3-6, move the mouse cursor to the

area where the video image appear, the video will display full screen by double
clicking the mouse. You can quit the full screen by again double clicking the mouse or
pressing button [Esc].

10

ANPR922M3M user manual – 1st ed.

(Picture: 3-6)

4. Video Playback

4.1 Local Video Playback

1. Local Video Playback. As shown in picture 4-1, click [Playback] on the navigation bar,

to jump to the video [Playback] page. The image in red area indicates the remote
local video playback. Yellow font under the red area means channel name and white
font means current condition.

2. Check Local Video Files. As shown in picture 4-1, select query [Year] [Month] [Date]

in the green area, click [Query] button. This icon indicates Query button and you
will find out video files within your condition. If you select the year, month, date did
not meet the conditions of the video file, click [Query] button, to remind you “no
record” and [Slow forward], [Fast Forward], [single frame], [Snapshot], [Audio] button
turn grey color, because they are unavailable.

11

ANPR922M3M user manual – 1st ed.

(Picture: 4-1)

3. Play button . First check the recorded video file. When there is eligible video file,

click [Play] button, to jump directly to the starting part of the video file for playing, as
shows in picture 4-2. In the meantime, [Slow Forward], [Fast Forward], [Single
Frame], [Snapshot], [Audio] button will be settable, at the same time the channel
number in yellow font and the current status in white font will also display some
information.

4.Pause button . This icon is pause function if the video is already playing. When the

mouse points to the icon 12 sas12o display “pause” words and clicking [Pause] button
will pause the video being played.

5. Stop button . This icon indicates that the video playback is stopped. When you

are playing the video and then you click [Stop] button, there will not be any video
display on the progress bar. Meanwhile background will turn grey color and will not
play video.

6. Slow Forward button . This icon indicates that the video slow forward. When the

process playback video is playing, click on the [Slow Forward] button, to slow down
the speed of video playback.

7. Fast Forward button . This icon indicates that the video fast forward, when the

process playback video is playing, click on the [Fast Forward] button, to accelerate
the speed of video playback.

12

ANPR922M3M user manual – 1st ed.

8. Single Frame Play button . This icon represents a single frame play. If you click

a single frame, to click once [Single Frame] button to display a single frame of a
picture.

9. Snapshot button . This icon indicates snapshot function. During playback, click

this button, to snapshot current playback video image and will be saved in a defined
snapshot stock path.

10. Audio button . This icon represents audio. Click [Audio] button during the local

video intercom operation, click [Audio] button and the sound turned on, you will hear
in the video intercom words.

11. Progress bar . This icon indicates a period on the progress bar. The

recording information is displayed on the progress bar according to the conditions of
the query. Red means alarm recording, yellow means manual recording, blue means
normal recording.

(Picture: 4-2)

12. Positioning function. As shown in picture 4-3, red area is for positioning function

operation. this icon is the position button in red area. When doing normal video
playback, choose your own defined [Hour] [Minute] [Second] and then click
[Positioning] button, the system will automatically position to the eligible set time
period for playback of the local recording.
(Note: to operate the positioning function you need to have the video for playback)

13

ANPR922M3M user manual – 1st ed.

(Picture: 4-3)

4.2 Remote Recording Playback

1. Remote Recording Playback. As shown in picture 4-4, click [Playback] on the

navigation bar, to jump to the video [Playback] page. The image in red area indicates the
remote local video playback. Yellow font under the red area means channel name and
white font means current condition.

2. Check Remote Video Files. As shown in picture 4-5, select query [Year] [Month] [Date]

in the green area. Click [Query] button. The icon indicates query button, and you
will find out video files within your condition. If you select the year, month, date did not
meet the conditions of the video file and click [Query] button, to remind you “no record”
an nd [Slow forward], [Fast Forward], [single frame], [Snapshot], [Audio] button turn
grey color, because they are unavailable.

14

ANPR922M3M user manual – 1st ed.

(Picture: 4-4)

3.Playback operation. Button【 】represents play, first check the recording video file,

when there is eligible video file, click 【Play】 button, there will be a time buffer. In the
meantime, the IPC video file will be downloaded to local, which means in the path set of
where the local video files stored. When buffer finished, to jump directly to the location
where start playing the video file for playback. In the process of playing, if disk space to
store is less than 500MB, remote playback page will direct prompt words "disk space full".
In the process of playing video [Slow Motion], [Forward], [Single Frame], [Snap], [Audio]
button will be settable, like picture 3-1-2 shows. At the same time the channel number in
yellow font and the current status in white font will also display some information.

4. Pause function. also represents pause. If already plays video, when mouse

pointing, this icon will appear “pause” words. Click button, to pause the video being
played.

5. Stop Function. Click for stop playing, during the process of playing a video. Click

[Stop] button, the display area on progress bar will not have a video image for display, to
display gray background color, will not play video. Then click [Play] button, to continue
video play.

6. Slow Forward function. represents video slow motion. During playing video

process, click [Slow motion] button, to slow down video playing speed.

7. Forward function. represents video fast forward. During playing video process,

click [Forward] button, to accelerate the speed of video playback.

15

ANPR922M3M user manual – 1st ed.

8. Single frame play function. represents single frame play. If click single frame, to

appear picture with each frame.

9. Snapshot function. represents snapshot. Click [Snapshot] button, will snapshot the

video picture, stored in the capture setting path.

10. The audio function. represents sound. Click [Audio] button during the process. If

there was a local video intercom operation, click [Audio] button You will hear the voice in
the video

11. Progress bar function. For example: this icon indicates a period on the

progress bar. The recording information is displayed on the progress bar according to
the conditions of the query. Red means alarm recording, yellow means manual
recording, blue means timer recording.

(Picture: 4-5)

12. Positioning function. As shown in picture 4-6, the red area indicates the operating

area. is the position button. When doing normal video playback, choose your own
defined [Hour], [Minute], [Second] and then click [Positioning] button, the system will
automatically position to the eligible set time period for playback of the local recording.
(Note: to operate the positioning function, first of all you need to have the video for
playback.)

16

ANPR922M3M user manual – 1st ed.

(Picture: 4-6)

(Note: to enable this feature, verify if your IPC model have the playback functions)

5. Checking Pictures

5.1. Checking Pictures

1.Picture snapshot query. As shown in picture 5-1, query according to the setting
conditions, to demonstrate pictures in compliance with the conditions of the query
on the right.

17

ANPR922M3M user manual – 1st ed.

(Picture: 5-1)

2.Remote snapshot query – snapshot type. [Snapshot type] is divided into: All, Timing

snapshot, detection snapshot, detector snapshot. When [Snapshot type] is All, click
[Query] button, on the right list will show all the snapshot pictures. When [Snapshot type] is
Timing snapshot, on the right list will show all the timing set snapshot pictures. When
[Snapshot type] is Timing snapshot, [Query type] choose according to time span. Setting
start time and end time, click [Query] button, on the right list will show snapshot pictures in
the setting time period.

3. Snapshot search – Query type. [Query type] is divided into: Query according to All time

or time period. When [Query type] is All time, the start time (hours, minutes, seconds) and
end time (hours, minutes, seconds), the status will not be editable. Click [Query] button,
to display all snapshot pictures in the memory card. When [Query type] is time period, the
start time, minutes, seconds and end time, minutes and seconds will be set off and
change into editable status. Select the start time (hours, minutes, and seconds) and end
time (hours, minutes, and seconds). Click [Query] button, the eligible snapped pictures
will be displayed in the list on the right.

4. Delete. Choose the data according to the list, click [Delete] button, will delete the data

which are chosen.

5. All delete. Click [All delete] button, will delete all the snapshot pictures.

6. Query snapshot pictures. On the right list choose picture you want to check, click left

button on the mouse will pop up a new page, then shows the picture chosen.
(Note: to enable this feature, verify if your IPC model have the function)

6.Setting

Parameter configuration, as picture 6-1 show, is divided into local parameter and Remote
control parameter.

18

ANPR922M3M user manual – 1st ed.

(Picture:6-1)

6.1. Local parameter

6.1.1. Path configuration

Path configuration, as picture 6-1-1 shows, set recording file save path and preview
snapshot save path.

(Picture: 6-1-1)

1.When setting record file save path, click [Browse] button, to pop up choosing file
save path message, as picture 6-1-2, choose the save path and folder to save file,
click [OK] button, the page will show settled video file path, click [Save] button. When
local recording, video files will be stored in the settled video file path.

19

ANPR922M3M user manual – 1st ed.

(Picture: 6-1-2)

2.When setting the preview snapshot save path, click [Preview] button, will pop up
page like picture 6-1-2, choose the save path, click [OK] button, the page will shows
the settled down save path, click [Save] button. When local capturing, to store
captured pictures in the settings path.

6.1.2. Local recording plan

Local recording plan, as picture 6-1-3 shows.

(Picture: 6-1-3)

1. Select “Local Plan Check”, system will start recording according to the setup

information, the local recording file will be saved in the identified file stock area of [local
parameter].

2. Set up the maximum record time, this function allows system to separate recording file

according to the maximum time setting for record. For example, if user set the maximum
record time at 60 min, each recording file stocked in local will be 60 min.

20

ANPR922M3M user manual – 1st ed.

3. When system recognizes the recording disk is full, system will display “cycling

coverage” and “stop recording” for user selection.

3.1. Cycling coverage. When the setting disk is full (less than 500MB), to delete the local

recording file on the same camera the day before.

3.2. Stop recording. When setting disk space is full, if set stop recording, then will stop

local recording.

4. Set record time. Choose one day from Monday to Sunday or check time setting in one

day from Monday to Sunday.

5. Time period. Divide into 4 time period: Start time, hour, minute, second and end time,

hour, minute, second (example: choose single box of Monday, select para 1, set start
time: hour: 00, minute: 00, second: 00, end time: hour: 08, minute: 00, second: 00, click
[Save] button, then the first time span of Monday have been settled. Then choose para 2
of Monday, choose single box of Monday, set start time: hour: 08, minute: 00, second: 00,
end time: hour: 12, minute: 00, second: 00, click [Save] button, this is setting the second
time span of Monday. Then choose para 3 of Monday, choose single box of Monday, set
start time: hour: 12, minute: 00, second: 00, end time: hour: 18, minute: 00, second: 00,
click [Save] button, this is setting the third time span of Monday. Then choose para 4 of
Monday, choose single box of Monday, set start time: hour: 18, minute: 00, second: 00,
end time: hour: 23, minute: 59, second: 59, click [Save] button, this is setting the fourth
time span of Monday. Then turn to preview page, when the setting time is ok to start local
recording, the recording file is in the settled save path in local parameter, other day
setting is same as Monday)

7. Copy to. Choose from Tuesday to Sunday, then click “copy to”, to copy the time

setting of Monday from Tuesday to Sunday. If select all, to choose from Tuesday
to Sunday (example: choose Monday, then choose para1, select time: hour: 08,
minute: 00, second: 00 and end time: hour: 22, minute: 00, second: 00, then click
from Tuesday to Sunday or select all. Click [Copy to] button, copy the time setting
in Monday from Tuesday to Sunday, as picture 6-1-4)

(Picture: 6-1-4)

6.2 Remote Configuration

1. Remote Configuration: remote configuration includes basic setting, network parameter,

alarm server setting, issues management, user arrangement, system maintenance.

21

ANPR922M3M user manual – 1st ed.

6.2.1 Basic Information

6.2.1.1 Basic setting

Basic setting, as shown in picture 6-2-1-1, includes Time Zone, Set Time, Enable NTP or
not, NTP Server, Pan address, Device ID, Enable UPNP or not, PC Time Syn, OCX
Version, IPC Version, IE Version.

(Picture: 6-2-1-1)

1. Time Zone. When select different time zone, the time will change correspondingly.

2. Set Time. When you choose yes for computer time synchronization, you cannot revise

the time. When you choose not for computer time synchronization, you can revise the
time of the device. Click [Save] button, the device will not restart and you can enter into
the Preview interface to check the revised value at the left upper corner of the picture.

3. Enable NTP or not. Enable or Disable

4. NTP Sever. You can input the NTP Server address manually.

5. Pan address. The text-box is editable, and the value range is 0-255.

6. Device ID. It shows the serial number of the device

7. Enable UPNP or not. Enable or Disable

8. PC Time Syn. When log in with the Web interface, to be PC Time Syn automatically.

9. OCX Version. It shows the OCX version and it cannot be revised.

10. IPC Version. It shows the serial number of the main program and it cannot be revised.

11. IE Version. It shows the serial number of the web page and it cannot be revised.

22

ANPR922M3M user manual – 1st ed.

6.2.1.2 Video Setting

Video setting, as shown in picture 6-2-1-2, includes System (Pal, NTSC), Stream Type
(Mainstream, Sub-stream), flips, Compression type (H.264), Mode (constant,
changeable), Resolution (QCIF, CIF, D1, 720P, 1080P, 1600X1200, 2048X1536), video
quality, Stream, I frame interval.

(Picture: 6-2-1-2)

1. Standard. Standard can divide into NTSC and PAL. When choosing NTSC, click

[Save] button, the page will jump to the countdown for equipment to restart. After
completed, to jump to the preview page and to display 30 FPS on the video preview
page. If choosing PAL, click [Save] button, the page will jump to the countdown for
equipment to restart. After completed, to jump to the preview page and to display 30
FPS on the video preview page.

2. Stream Type. It includes main stream and sub stream. When setting the code pattern,

resolution, image quality, the size of the stream, and the I frame interval of main
stream, click [Save] button, the page will jump to the countdown to restart equipment.
After the restart completed, to display the corresponding modified value of the main
stream at video settings page (note: when the modification of main stream and sub

stream value finishes, if you select needed code type at the [ ],
to display the revised video output pattern.)

3. Frame rate. PAL (1-25fps) NTSC (1-30fps) adjustable.

4. Compression type. H.264.

5. Stream mode. User can select constant bit rate or changeable bit rate.

6. Video Storage. It includes QCIF, CIF, D1, 720P, 1080P, 1600X1200, 2048X1536

7. Image quality. User can freely choose in drop-down box.

8. Stream. User can freely change in the text-box.

9.I frame interval: User can freely change in the Text-box.

23

ANPR922M3M user manual – 1st ed.

6.2.1.3: Remote Recording Plan

Remote recording, as shown in picture 6-2-1-3

(Picture: 6-2-1-3)

1. Remote Enable. Click the check box, then the recording plan will be remotely

controlled. The recorded file will be stored in SD card, and user can play back these files
in play-back windows.

2. Sets the maximum length of video files, the video file will be separated according to the

set of video length. If the maximum length for video files is 60 minutes, then each local
video file length will be 60 minutes.

3. Setup time. Monday to Sunday can be selected, you can also view the time setting of

one day from Monday to Sunday.

4. Set record time period: divided into 4 time period: Start time (hour, minute, second) and

end time (hour, minute, second) (example: click the radio button before Monday, then
select the value of section 1. Setting the start time at 00: 00: 00, end time at 08: 00: 00,
click [Save] button, and this is the setting of the first recording time period. Then select
the value of section 2of Monday: setting the start time at 08: 00: 00, end time at 12: 00:
00, click [Save] button, and this is the setting of the second recording time period. Then
select the value of section 3of Monday: setting the start time at 12: 00: 00, end time at 18:
00: 00, click [Save] button, and this is the setting of the third recording time period. Then
select the value of section 4 of Monday: setting the start time at 18: 00: 00, end time at
23: 59: 59, click [Save] button, and this is the setting of the forth recording time period.
When the device is accord with the recording to perform front-end recording and the
recording file will be stored in the SD card. User can check them at the IPC setting in the
Playback page)

24

ANPR922M3M user manual – 1st ed.

5.Copy to. Click the check box from Tuesday to Sunday, then click “Copy to”, to copy
the setting of Monday to Tuesday to Sunday. When click select all, to select Tuesday
to Sunday automatically (example: first select Monday. Then select Para 1, choose
the values, the starting time and the end time, then select Tuesday to Sunday or
select all. Click “Copy to” button, to copy the time setting of Monday to Tuesday to
Sunday, as shown in picture 6-2-1-4)

(Picture: 6-2-1-4)

(Note: to enable this feature, verify if your IPC model have the function)

6.2.1.4 SD card management

SD card management, as shown in picture 6-2-1-5

(Picture: 6-2-1-5)

1. Dropped Networking recording automatically and uploading continually: default

selected and cannot be modified.

2. Check the SD card. “ Check the SD card ”, to show the SD card remaining memory

condition. As shown in picture 6-2-1-6, the total capacity is 8GB, the used capacity is

718.8MB and the remaining usable capacity is 6.7G.

25

ANPR922M3M user manual – 1st ed.

(Picture: 6-2-1-6)

3.Format SD card. All contents will be deleted. Click “Format SD card ”, then click
“check SD card” like picture 6-2-1-7 shows, the use of the SD card is OK, which
means the SD card is formatted.

(Picture：6-2-1-7)

4.SD Card full. User can choose stop recording or loop recording. When SD card is

full, if choose Stop and click “Save”, to stop IPC recording and snapshot; if choose
Loop recording and click “Save” button, the new IPC recording file will cover the

earliest recording file.

(Note: to enable this feature, verify if your IPC model have the function)

6.2.1.5 Motion Detection Setting

Motion detection setting, as shown in picture 6-2-1-8

26

ANPR922M3M user manual – 1st ed.

(Picture: 6-2-1-8)

1.Setting area. As shown in Pic 6-2-1-9, user can make motion detection for a certain
region.

(Picture: 6-2-1-9)

2. Enable Motion Detection. Click the check box before the “Enable Detection”, to perform

motion detection according to set information.

3. Alarm duration. It indicates the lasting time of the alarm for motion detection

4. Detection sensitivity. There are low, middle, high for option

5. Setting time. Any day from Monday to Sunday can be selected, you can also view the

time setting of one day from Monday to Sunday.

6. Set time period. Divided into 4 time period: Start time (hour, minute. Second) and end

time (hour, minute, second) (example: click the radio button before Monday, then select
the value of section 1:setting the start time at 00: 00: 00, end time at 08: 00: 00,

27

ANPR922M3M user manual – 1st ed.

click "save" button, and this is the setting of the first recording time period. Then select
the value of section 2 of Monday: setting the start time at 08: 00: 00, end time at 12: 00:
00, click "save" button, and this is the setting of the second recording time period. Then
select the value of section 3 of Monday: setting the start time at 12: 00: 00, end time at
18: 00: 00, click "save" button, and this is the setting of the third recording time period.
Then select the value of section 4 of Monday: setting the start time at 18: 00: 00, end time
at 23: 59: 59, click "save" button, and this is the setting of the forth recording time period.
When the set time period trigger the motion detecting events, to perform motion detection
alarm, at the same time, to also perform the front-end recording. And the motion detecting
video files will be stored in SD card. User can check the motion detection file at the front­end playback in the playback page, at the same time when trigger alarm, to send mail
and upload the snapshot image to the FTP.)

7. Copy to. Click the check box from Tuesday to Sunday, then click “Copy to”, to copy the

setting of Monday to Tuesday to Sunday. When click select all, to select Tuesday to
Sunday automatically (example: first select Monday. Then select Para 1, choose the
values, the starting time (08:00:00) and the end time (22:00:00), then select Tuesday
to Sunday or select all. Click “Copy to” button, to copy the time setting of Monday to
Tuesday to Sunday, as shown in picture 6-2-1-10)

(Picture: 6-2-1-10)

28

ANPR922M3M user manual – 1st ed.

6.2.1.6 Snapshot setting

Snapshot setting, as picture 6-2-1-11

(Picture: 6-2-1-11)

1.Enable Snapshot. Select snapshot enable/disable on the top of the screen, camera

will snapshots according to snapshot setting.

2.Snapinterval setting. When finish snapinterval set, press [Save] button, camera will

snapshots according to the snapping interval setting (example:set up start time as
08:00:00, end time as 22:00:00, camera will snapshots the first image from 08:00:00,
then snapshots the next image after 60 seconds)

3. Set time. Freely select anyday from Monday to Sunday, freely check the time setting

of any day from Monday to Sunday.

4. Para. Divide into 4 para in total. Start time, hour, minute, second and end time, hour,

minute, second (example: select Monday and para 1, set the start time as: 00 hour 00 min
00 sec, end time as 08 hour 00 min 00 sec, press [Save] button, the snapshot setting for
para 1 of Monday is done. Then Select Monday and para 2, set start time as 08 hour 00
min 00 sec, end time as 12 hour 00 min 00 sec, press [Save] button, the snapshot setting
for para 2 of Monday is done. Then Select Monday and para 3, set start time as 12 hour
00 min 00 sec, end time as 18 hour 00 min 00 sec, press [Save] button, the snapshot
setting for para 4 of Monday is done. Finally Select Monday and para 4, set start time as
18 hour 00 min 00 sec, end time as 23 hour 59 min 59 sec, press [Save] button, the
snapshot setting for para 4 of Mondy is done. Snapshots will save in SD card.)

5.Copy. Select Tuesday to Sunday, then press [Copy], all setting of Monday will copy to

Tuesday to Sunday, when select all day system will automatically select Tuesday to
Sunday (example: select Monday first, then select para 1, set start time as 08:00:00 and
end time as 12:00:00, then select Tuesday or select all, then press [Copy], all setting of
Monday will copy to Tuesday to Sunday, as picture 6-2-1-12)

(Note: to enable this feature, verify if your IPC model have the function)

29

ANPR922M3M user manual – 1st ed.

(Picture: 6-2-1-12)

6.2.1.7.Alarmset

Alarm input setting, as picture 6-2-1-13)

(Picture: 6-2-1-13)

1.Enable Alarm. Select “Enable”, when activate detector alarm, preview screen will

shows the front-end alarm information.

2. Alarm output. When selected, output notification will be sent when alarm happens.

3. Record output. When selected, system starts record when alarm happens.

4.Alarm time. Set the duration in bar 5.Detector type. Open or close is selectable

6.Set time. Freely select any day from Monday to Sunday, freely check the time setting

of any day of Monday to Sunday.

7.Para. Divide into 4 para in total. Start time, hour, minute, second and end time, hour,

minute, second (example: select Monday and para 1, set the start time as: 00 hour 00
min 00 sec, end time as 08 hour 00 min 00 sec, press [Save] button, the alarm setting for
para 1 of Monday is done. Then Select Monday and para 2, set start time as 08 hour 00
min 00 sec, end time as 12 hour 00 min 00 sec, press [Save] button, the alarm setting for
para 2 of Monday is done. Then Select Monday and para 3, set start time as 12 hour 00

30

ANPR922M3M user manual – 1st ed.

min 00 sec, end time as 18 hour 00 min 00 sec, press [Save] button, the alarm setting
for para 4 of Monday is done. Finally Select Monday and para 4, set start time as 18
hour 00 min 00 sec, end time as 23 hour 59 min 59 sec, press [save] button, the alarm
setting for para 4 of Monday is done. When alarm happens in the defined time para,
system will start alarm)

8.Copy. Select Tuesday to Sunday, then press [Copy], all setting of Monday will copy to

Tuesday to Sunday, when select all day system will automatically select Tuesday to
Sunday (example: select Monday first, then select para 1, set start time as 08:00:00 and

end time as 12:00:00, then select Tuesday or select all, then press ”copy”, all setting of

Monday will copy to Tuesday to Sunday, as picture 6-2-1-14)

(Picture: 6-2-1-14)

(Note: to enable this feature, verify if your IPC model have the function)

6.2.1.8 Serial set

Serial set, as picture 6-2-1-15)

(Picture: 6-2-1-15)

31

ANPR922M3M user manual – 1st ed.

1.Serial type: RS485 or RS232

2. Baud rate: 2400, 4800, 9600, 115200

3.Serial number: 7/8

4. Stop: 1/2

5. Verification: None/Odd/Even

6. PTZ:PELCO-D, PELCO-P

6.2.2 Network set

6.2.2.1 Network parameters

Network parameters. Network setting, PPPOE setting, DDNS setting, E-mail Setting,
FTP setting. Net work set: Max connections, IS enable DHCP: Enable/disable, IP
address, Subnet, Gateway, MAC address: info port, media port, http port, Main DNS,
sub DNS, as picture 6-2-2-1

(Picture: 6-2-2-1)

1.Max connections. After change max connection press [Save] button, Max connections

bar will shows modified value (example: set max connection as 5 and press [Save]
button, when equipment finish reboot the max connection value will shows 5, when
using IE to access the equipment the visitor can not be over 5, the sixth visitor cannot

32

ANPR922M3M user manual – 1st ed.

see any video).

2.Enable DHCP. Enable/disable selectable. When enable DHCP, the IP address, Subnet

and Gateway address will became not editable. Then press [Save] button, after finished
this setting, use [IPSEARCH] to search the IP address of equipment, DHCP server will
give an IP address to equipment. When disable DHCP, IP address bar, subnet, gateway
address bar will light up and became editable.

3.IP address. After modified IP address press “save” button, system will jump to the

screen of login page.

4. Subnet address. Modify the subnet address, then press [Save] button, the Subnet

address bar will shows the modified subnet address info.

5. Gateway address. Modify the gateway address, then press [Save] button, the

gateway address bar will shows the modified gateway address info.

6. Information port. Modify the info address, then press [Save] button, the info address

bar will shows the modified info address info.

7. Media port. Modify the Media port, then press [Save] button, the Media port bar will

shows the modified Media port info.

8. http port. Modify the web port, then press [Save] button, the http port bar will shows

the modified http port info.

9. Main DNS server. Modify the main DNS address, then press [Save] button, the Main

DNS bar will shows the modified Main DNS info. The Main DNS setting will directly effect
if the email can be send successfully when alarm happens.

10. Sub DNS server. Modify the sub DNS address, then press [Save] button, the sub

DNS bar will shows the modified sub DNS info

6.2.2.2 PPPOE Setting

PPPOE set: Enable PPPOE, PPPOE user name, PPPOE password. As picture 6-2-2-2)

(Picture: 6-2-2-2)

1.Enable PPPOE. Select PPPOE bar, press [Save] button, system will jump to the screen

of reboot

33

ANPR922M3M user manual – 1st ed.

and begin to count down. When finsihed reboot system will connect defined PPPOE by
dialing, when connection success, a new IP address will automatically give to equipment,
then we can use the new IP address to access (note: the new IP address is invisible, so
the equipment must be bound by realm name. If the first PPPOE dialing failed, system
will redial after every 5 minutes)

2.PPPOE user name. Enter the user name in the ID bar, press [Save] button, system will

jump to the screen of reboot and begin to count down. When finished reboot system will
connect defined PPPOE by dialing.

3. PPPOE password. Enter the password in the PPPOE bar, press [Save] button,

system will jump to the screen of reboot and begin to count down. When finished reboot
system will connect defined PPPOE by dialing.

6.2.2.3 DDNS Setting

DDNS set. Enable DDNS, protocol type (Dyn.3322.org), DDNS server, DDNS realm,
DDNS ID, password, as picture 6-2-2-3

(Picture: 6-2-2-3)

1.Enable DDNS. Select Enable DDNS, press [Save] button, system will jump to the

screen of reboot and begin to count down. When finsihed reboot, to be available to
analysis realm name (note: when enable DDNS, enable UPNP by click [remote set] 
[basic info]  [foundation set]) The set realm name can access this equipment by
WAN.

2.Protocol type. DynDNS and 3322.org selectable, only one type can be set.

3.DDNS server. Set Server according to the selected Protocol type (note: if you select

DynDNS type, the DDNS server should be checkip.dyndns.com)

4.DDNS Realm: enter your applied realm name in the DDNS realm bar, the entered

realm name will be use to access this equipment.

34

ANPR922M3M user manual – 1st ed.

5.DDNS ID. Enter the applied DDNS ID in the DDNS bar, press [Save] button, system will

jump to the screen of reboot and begin to count down, when finish reboot, system will
login the realm name according to the DDNS ID.

6.DDNS Password. Set DDNS password in “Password” and click [Save], then the page

will appear Device Reboot, after finished, the system will log in DDNS server according
to the DDNS set.

6.2.2.4 Email Set

Email Set: Enable Email, Motion Tittle, Alarm Tittle, SMTP Server, SMTP Port, User
Name, Password, Send E-mail, Receiver E-mail, Receiver E-mail, Receiver E-mail,
Receiver E-mail. As picture 6-2-2-4 below:

(Picture: 6-2-2-4)

1. Enable Email. Tick “Enable” and click “Save”, then the page will appear “Save

success”. When alarm or others triggered, snapshot images will be sent according to the

email set.

2. Motion Title. Set the title in “Motion Title”,when motion detection alarm triggered, the

title will be shown in email.

3. Alarm Title. Set the title in “Alarm Title”, when alarm triggered, the title will shown in

email.

4. SMTP Server. Set the sender email’s server address, and click “Save”, when alarm

triggered, snapshot images will be sent according to the email set (example: QQ
email’s SMTP server address is: smtp.qq.com)

5. SMTP Port. Set Port in “SMTP Port” and click “Save”, when alarm triggered, snapshot

images will be sent according to the email set (example: QQ’ s email SMTP port is 25)

6. User name. Set sender’s user name in “User name” and click “Save”, when alarm or

others triggered, snapshot images will be sent according to the email set.

35

ANPR922M3M user manual – 1st ed.

7. Password: Set password in “Password” and click “Save”. When alarm or others

triggered, snapshot images will be sent according to the email set.

8. Send E-mail. Set sender’s email address in “Send Email” and click “Save”, when

alarm and others triggered, snapshot images will be sent according to the email set.

9. Receiver E-mail. Set receiver’s email address in “Receiver Email” and click “Save”.

When alarm or others triggered, snapshot images will be sent according to the email
set.

6.2.2.5 FTP Set

FTP Set. Enable FTP Server, FTP Server, FTP Port, FTP Send Mode:
Passive&Negative, ID, Password, Upload path. As picture 6-2-2-5 below:

(Picture: 6-2-2-5)

1. Enable FTP Server: Tick “Enable” and click “Save”, the page will appear “Save

Success”, when alarm or others triggered, snapshot images will be sent according to the

FTP Set.

2. FTP Server. Set FTP Server address.

3. FTP Port. Set FTP port (default FTP port: 21)

4. FTP Send Mode. Passive&Negative option.

5. ID. Type the ID account and click “Save”, the page will appear “Save Success”. When

alarm or others triggered, snapshot images will be sent according to the FTP set.

6. Password. Type in the password and click “Save”, the page will appear “Save

Success”.

7. Upload Path. Type in the file name that you plan to store in the server and click

“test”. If FTP server is available and connected normally, the page will appear “Test

Success”. When alarm or others triggered, snapshot images will be sent to the file you
have set in “upload path”.

36

ANPR922M3M user manual – 1st ed.

6.2.3 Milestone Server Set

6.2.3.1 Milestone Server Set

Milestone Serve Set, as picture 6-2-4-1 below:

(Picture: 6-2-4-1)

1.Server IP Address. Type in milestone server’s address (example: if milestone server is

installed in a computer with IP address 192.168.0.155, then the server IP address to

192.168.0.155)

2. Milestone server port. Type in the server port, default is 1234.

3. Video Loss. Firstly, you need to add one regular event in milestone server and set

event sub-string, then build a alarm conception in “alarm conception”, add the regular
event into the alarm conception, here you must ensure the event sub-string has the
same name as the in “Video loss”, then when video loss alarm triggered, the alarm will
happen in milestone (example: if the sub-string in regular is set as “vloss”, and the
video loss is set “vloss” in milestone server, then the alarm event will be shown in
milestone.)

4. Motion Loss. Same procedure as Video Loss.

5. Detector Note. Same procedure as Video Loss.

6.2.4 Event Management

Event Management, as picture 6-2-4-1 below:

(Picture: 6-2-4-2)

1. Motion. After clicking “Motion”, the page will be Motion Set.

2. Alarm. After clicking “Alarm”, the page will be Alarm Set.

6.2.5 User Management

User Management: Example 37 sas picture 6-2-5-1 below. Users will be divided into 3
levels, each will be different, means you have the authority , means you don’t

have the authority.

37

ANPR922M3M user manual – 1st ed.

(Picture: 6-2-5-1)

1. Levels. Divided into “Manager”, “Maintenance Staff”, “User”.

2. User name. Type in user name in “User Name”.

3. Password. Type in password in “Password”.

4. Confirm. Confirm the password in “Confirm”.

(Picture: 6-2-5-2)

6.2.6 System Maintenance

System Maintenance, as picture 6-2-6-1 below:

38

ANPR922M3M user manual – 1st ed.

(Picture：6-2-6-1)

1. Default. Click “Completely” will default the system.

2. Reboot. Click “Sure” will reboot the device.

7. Operation Environment

7.1 Operation System

Operation System: Windows XP, Windows7, Windows Server 2003

7.2 Browser Compatibility

IE Browser: IE7.0, IE8.0, IE9.0, IE10

39