How it Works
Colorlight
Loading...
S2
User Manual
24 pgs1.62 Mb0

Colorlight S2 User Manual

Download
Page 1
S2 Synchronous Sender
Page 2
www.colorlightinside.com
Contents
1. Introduction ....................................................................................................................................................................... 1
2. Interface Description .......................................................................................................................................................... 1
3. Hardware Connection ........................................................................................................................................................ 3
4. LEDVISION Installation and Preliminary Configuration ....................................................................................................... 4
5. Parameter Configuration .................................................................................................................................................. 11
5.2.1 Sending Device Setting .................................................................................................................................... 15
5.2.2 Screen Parameters ........................................................................................................................................... 17
5.2.3 Connection Parameters (Look from front) ....................................................................................................... 18
Page 3
www.colorlightinside.com
1
1. Introduction
As a new generation of sender, S2 Sender has updated its core chips, and the performance significantly improved. It
adopts dual USB2.0 as the communication interface to achieve high speed communication between the PC and senders. S2
Sender realizes cascading between multiple senders and much more convenient. S2 Sender can be applied to small display
perfectly.
2. Interface Description
Page 4
www.colorlightinside.com
2
No
Name Function Remarks
1
Indicator panel
and Configuration
button
Adjust the brightness of the entire screen ( 16 levels ); Display the whole screen test mode conversion
Press “+”and “–“together to switch between brightness adjustment and testing mode.
2 Power Switch On/off
3 Power Socket AC 100~240V
4 Output Ports RJ45, to transmit network signals
The control area of the two outputs can be separately set.
5 Audio input Input audio signal via Ethernet cable
6 USB TYPE-A USB output, cascading among multiple senders
7 USB TYPE-B USB input, connecting PC for configuring parameters
8 DVI Input DVI output interface, connect to the graphics card
Page 5
www.colorlightinside.com
3
3. Hardware Connection
1) Power Supply (PCI)：
Match with computer PCI slot, or DC 3.8-12V for power supply.
2) Video Signal Input（DVI）：
Connect PC with S2 via proper DVI/HDMI cable via DVI interface.
3) Screen Configuration (USB)：
Use a standard USB A/B cable to connect S2 with PC for S2 configuration.
4) Ethernet Cable (RJ45)：
Connect S2 sender with the receiving card via Ethernet cable for controlling receiving card and the screen (Note: The Ethernet cable
must be CAT5E or CAT6).
Page 6
www.colorlightinside.com
4
4. LEDVISION Installation and Preliminary Configuration
4.1 Computer Configurations
CPU Frequency>= 2.0GHZ
Host Memory>=1G
Graphic card with DVI/HDMI interface: Memory ≥512MB
The resolution of PC’s graphic card should be equal to or larger than the actual LED display’s.
Computer configuration can be adjusted according to the actual situation. Adjustment mainly aims at total pixels of LED
display, the complexity of playing contents and whether playing HD video or not.
Page 7
www.colorlightinside.com
5
4.2 USB Driver Installation
First download the installation package of LEDVISION software from Colorlight’s official website www.colorlightinside.com,
and complete the installation according to the diagrams shown below.
1. Run the software package, and select [ English ] for installer language. Click [ OK ] to move on.
Note: Run LEDVISION version 4.18 or higher while using S2.
Page 8
www.colorlightinside.com
6
2. After selecting a language, an installation wizard like below will appear. Click [ Next ];
Then choose installation location, click [ Browse ] to change default target location, then click [ Next ] after completing.
Choose components according to your own computer status, click [ Install ] to complete.
After the installation is complete you are ready to use LEDVISION.
Page 9
www.colorlightinside.com
7
4.3 Graphic Card Settings
Set up the working mode of the computer graphic card after completing hardware connection and powering S2 on, you
can select Duplicate mode or Extend mode according to the different requirements.
Duplicate Mode: That the contents displayed on LED screen are consistent with computer, that is to say, copy the
computer contents onto LED screen, as pic below.
PC Screen LED Screen
Page 10
www.colorlightinside.com
8
Extend Mode：That the contents displayed on LED screen are inconsistent with computer’s, that is, to extend a
display image from the right side of PC screen, which was consistent with LED display’s, we also call it “background
playing”, as pic below.
PC Screen LED Screen
Page 11
www.colorlightinside.com
9
For different computers, there are different ways to change the mode. Take WIN 7/8 system + NVIDIA graphics cards as an
example, please read the following settings ways.
Method 1: Hold down the WIN and P keys at the same time, and select the mode as you want in the pop-up
window.
Method 2: Right-click and select “Screen resolution” to enter the page of “modify the
display appearance”; if your graphics card is not NVIDIA and cannot find the setting
interface please refer to the description of the graphics card.
Page 12
www.colorlightinside.com
10
Note: As for other kinds of graphic cards, if there is no corresponding window, please refer to the user manual of
the graphic card.
Page 13
www.colorlightinside.com
11
5. Parameter Configuration
First of all, please make sure the software under i Series
Mode before setting.
Click the “Setting” > “Software Setting” to enter the
Software Management window, change the mode by
inputting password: 168.
Page 14
www.colorlightinside.com
12
5.1 Confirmation on Hardware Connection
Please make sure the correctness of the hardware connection before setting, use LEDVISION to detect sender and all
receiving cards.
5.1.1 Detect Sender and receiving card
Run LEDVISION, click the “Control” > “Screen Control” to enter the Screen Control window.
Page 15
www.colorlightinside.com
13
Select [ Sender Card ] for sending device, Click [ Detect Sender Cards ] in Sender Card Settings. Please check the
hardware connection or the installation of relevant driver if cannot detect sender cards.
Select network port and click “Detect Receiver Cards” respectively, the software will automatically acquire the
Receiver (Receiving card) quantity for each network port of the sender. Please check corresponding cable if the numbers of
receiving card are inconsistent with actual status.
Page 16
www.colorlightinside.com
14
5.2 LED Screen Setting
Click “LED Screen Settings” and input password [ 168 ] to enter the LED Screen Setting interface, and set up “Sending
device”, “Screen parameters”, “Connection parameters”.
Page 17
www.colorlightinside.com
15
5.2.1 Sending Device Setting
Configure on the relevant parameters of the sender card.
Sender Card Resolution: Generally, sender card resolution must be consistent with the graphic card’s.
Page 18
www.colorlightinside.com
16
Input Signal Information: Display the sender info that auto acquired via the software, which only provided for reference, and did not support
personally set up.
Advanced: Prepare for professionals for special applications settings, no operation allowed for non-professionals.
Advanced settings include the parameters listed below:
Zero Frame Delay: Default uncheck, and should be enabled by technician under special status.
Auto Switch DVI/HDMI: The sender only identifies the video signal that has been set up when unchecked; Auto identify the signal that has
been connected first when checked.
Brightness adjustment via multi-function card: Auto adjusts screen brightness via the sensor of multi-function card when checked.
Maximum Transmission Unit (MTU): Default “Standard”, and consult with the technician if you need to apply to “Long Frame”.
Frame Output: Default “Every Frame”, and consult with the technician if you need to apply to “Every Other Frame”.
Input Bit Depth: Default “8bit”.
Input Type: DVI/HDMI, according to the actual using status.
Sync Method: Default “Auto”
Write logo: Custom, display before video signal input. The image formats should be bmp, jpg or png.
3D Setting: Works only for the function setting of 3D sender, did not apply for S2.
Page 19
www.colorlightinside.com
17
5.2.2 Screen Parameters
Observe the display screen with single cabinet as unit, if all cabinets display normally (it is normal circumstance even the
picture between cabinets is not continuous), please ignore this step and directly go to the next step.
Otherwise, enter the following configuration:
Click [ Load ], choose the correct parameter file.
Click [ Send ], to send the loading parameter to the
receiving card. Each cabinet should display normally (it
is normal circumstance even the picture between
cabinets is not continuous), then click [ Save To
Receiver ] to save the parameters to the receiver card.
If each cabinet cannot display normally, then
contact with the LED screen engineers.
Page 20
www.colorlightinside.com
18
5.2.3 Connection Parameters (Look from front)
You don’t need to set up the control area of each net port respectively under i series mode, but set up the connection relationship of the receiver card aiming at each net port loading via the sender, and the software will auto calculate and set up the control area according to the connection relationship. Detailed Setting Steps as follows:
1) Set up the quantity of receiving card
Set how many Receiver (Receiving card) that one port manages in Row Count and Col Count (6*6 as an example), how many pixels that one Receiver (Receiving card) manages in Width and Height (128*128 as an example), you will see led display mapping area from the right side (Viewing from the front of led display).
Page 21
www.colorlightinside.com
19
2) Receiver Card Parameters Setting
Select the target sender and the net port from the left side, then select the corresponding cabinets of net port actual control area and set the connection lines in the mapping area.
There are two methods to set up:
1. Use mouse to select one by one
Page 22
www.colorlightinside.com
20
A. In the mapping area, select the first receiving card based on the actual connection of the net port (view from the front), and then set up the actual loading width and height of the target receiving card in the right side (128*128 as an example).
B. Click the Receiver (Receiving card) one by one until the last one for this network port loads.
2. Connection Pattern
A. Aiming at the LED screen with standard connection lines.
B. First set up the receiving card information according to the
actual loading width and height (128*128 as an example).
C. Select the connection line you want from the right side, then
cover the corresponding area of net port loading in the mapping
area, finally complete setting.
As the cabinets have multiple specification (that is the
inconsistent capacity of the receiving card), you can select the
different one to adjust separately after completing setting.
Page 23
www.colorlightinside.com
21
3) Send to Receiver Cards & Save to Receiver Cards
Set up all the receiving card parameters and connection line respectively, click [ Send ] to send the correct parameter to the receiving card, and
the screen should display normally about this time.
Then click [ Save to Receiver ] to save parameters to corresponding receiving card after confirming.
Page 24
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use