Code Alarm ca6554 Professional Series Installation Manual

CCJCc:~LA~m

i=)~OFESSIONAI

SE~IES

Security and Remote

for models:

ca6554

Start Installation Guide

Voxx Electronics Corporation.

2014

All

rights reserved.

428592

Table

Before You Begin ......................................................................................... 4

Wire Connection Guide ............................................................................... 5

of

Contents

4 Pin Main Harness ................................................................................... 7

6 Pin

Start

Harness ................................................................................... 8

6 Pin Output Harness ..............................................................................

8 Pin

Input Harness .................................................................................

4 Pin Alternate Output Harness ............................................................... 14

4 Pin AUX Output Harness ...................................................................... 15

3 Pin Door Lock Output Harness ............................................................. 16

Add itiona I Ports .........................................................................................

Antenna OBI

Telematic

Set Up

I

LED

I

Programming Port ........................................................ 20

Port ...................................................................................................

Interface

&

Programming .............................................................................

Port ........................................................................... 20

10

11

20

21

Transmitter Programming ........................................................................

Manual Feature Programming .................................................................

21 21

Programming Feature Banks .................................................................. 22

Tach Smart Adjusting the Testing the

Programming .................................................................................. 25

Tach less Mode .............................................................................. 25

Shock Sensor .................................................................... 26

Shock Sensor

........................................................................ 26

Chirp Delete - User Accessible ................................................................ 26

Dome Light Delay

I

Theater Dimming ..................................................... 26

2

ca6554

Install

revA

Feature Descriptions .................................................................................

27

Transmitter Button Functions ..................................................................

Security Remote System

Trigger Zones ..............................................................................

Start

Layout

Shutdown Diagnostics ......................................................

...........................................................................................

35

37 37

38

Electronics

Voxx

2014

Corporation.

rights reserved.

All

3

BEFoRE

YOU BEGIN

FOR AUTOMATIC TRANSMISSION VEHICLES ONLY.

PROFESSIONAL INSTALLATION

STRONGLY

Roll

down window to avoid

during

Avoid mounting components or routing wires near hot surfaces

Avoid mounting components or routing wires near moving parts

Tape or

appearance

installation

loom wires under hood for protection and

RECOMMENDED

locking keys

in

vehicle

Use a circuits. "COMPUTER SAFE PROBE"

bags

•

.

4

Digital Multi Meter for testing and verifying

DO NOT USE A

or

damage

vehicle computers.

Technical Support

http://avxtech1.com

TEST LIGHT,

as these can set off air

(BOO)

or

go

to

OR

421-3209

ca6554

Install

revA

z

<(

~

z

a:

.q-

WHITE/RED WHITE PARKING LIGHT OUTPUT BLACK BROWN

PARKING LIGHT INPUT

GROUND SIREN OUTPUT (

+ )

r-

ex:

<(

r-

(/)

z

a:

c:o

r-

::>

n.

r-

::>

0

z

n.

c:o

PURPLE STARTER RED BATTERY ORANGE ACCESSORY

PINK/WHITE IGNITION RED/WHITE PINK IGNITION

BROWN/BLACK BLUE/BLACK START VIOLET/BLACK

RED/WHITE L T GREEN/BLACK

BATTERY

HORN OUTPUT

AUX TRUNK RELEASE FACTORY DISARM

OUTPUT-

12V

2

12V

1

STATUS

OUTPUT

1

(

MOTOR SIDE

+)

(

+ )

(

1

+ )

+)

(

+)

- )

(

ACTIVE OUTPUT

I

)

(-

OUTPUT

PULSE BEFORE START

I

( - )

(-)

- )

(

ORANGE GROUND

2014 Voxx

Electronics

Corporation.

WHEN

rights reserved. 5

All

ARMED

OUTPUT ( - )

8

>.

Input

Harness

1::J

a..

z z

a..

co

4

BLUE/WHITE INSTANT TRIGGER INPUT GREEN PURPLE WHITE/BLUE

GRAY GRAY/RED BROWN/RED PURPLE/WHITE

!

Pi

·

"'

··

···.·······

AI

~

terriate

BLACK/YELLOW

GREEN/WHITE

··.

Outp

DOOR DOOR ExrRENAL

HOOD PARKING BRAKE

TACH INPUT

·llt .

PULSE DURING PULSE

TRIGGER INPUT TRIGGER INPUT

START

PIN INPUT

BRAKE

INPUT ( + )

Ha

·

rness

AFTER

SHUTDOWN

INPUT ( - )

(-)

INPUT

CRANK

((

(-

( )

+ )

(

- )

)

- )

(-

)

x,_

=>::::>

<(a_

Zl-

-:::>

a..o

~

z~

-(.)

a..

a

('t')_J

LT BLUE L T GREEN/BLACK

PINK/BLACK ORANGE/BLACK GRAY/BLACK WHITE/BLACK

BLUE OPEN GREEN

FACTORY FACTORY

AUX

5 OUTPUT ( - )

AUX

4

OUTPUT

AUX

3

OUTPUT

AUX

2

OUTPUT

UNLOCK

LOCK

(-)

ARM DISARM

(-)

I

PULSE

( - ) ( - ) ( - )

AFTER

I

PULSE BEFORE

START

(-)

( - )

6

ca6554

Install

revA

4

Pln

Mail"l

Harness

1

2

Locate the parking

Positive switching Parking Lights:

Negative switching Parking Lights:

3

WHITE/RED PARKING LIGHT INPUT

WHITE PARKING LIGHT OUTPUT

light output wire at the

Verification:

turned on.

Connect the Connect the WHITE

Connect the Connect the

BLACK

This wire registers positive voltage

WHITE/RED

wire to the parking light output wire.

WHITE/RED wire to a good chassis ground. WHITE

wire to the parking

wire to a

vehicle's light switch.

Amp max fused battery source.

15

light output wire.

GROUND

when the parking

lights

are

chassis ground point using a ring

Connect the BLACK wire to a self tapping screw (not ensure a good connection. The recommended grounding point is a metal the driver's side kick panel

NOTE:

4

Locate a suitable from moving parts.

With the tapping screws, being

Connect the BLACK siren wire to a chassis ground using a ring terminal tapping screw (not

Route the BROWN siren output wire from the connect to the RED wire on the siren.

Do not ground the BLACK wire with any other

BROWN

mounting

of the siren aiming downwards, secure the siren

bell

supplied).

careful

supplied).

solid

Scrape away paint from the grounding point to

area.

location

not do drill

vehicle

SIREN

the engine compartment for the siren, away

in

OUTPUT (

into any hoses, wiring or components.

control module

+)

components.

in

through the

terminal

place using

and

surface

self

firewall

in

and

NOTE:

Voxx

2014

Be sure to

Electronics

Corporation.

loom the siren wires, and

seal the grommet.

7

1 PURPLE

Locate the vehicle starter wire.

STARTER OUTPUT ( + )

Verification: This wire registers voltage only when the key is turned to

START position. Cut the vehicle's starter wire

in

half when installing

starter kill relay.

Verification after starter wire is cut:

KEY SIDE

of

starter wire registers voltage when the key is turned to

START position.

of

MOTOR SIDE

starter wire registers no voltage.

Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE vehicle starter wire when installing the starter kill relay.

2

Locate 1

RED

of

the vehicle's constant 12 Volt battery wires at the ignition switch.

BATTERY 12V (

Verification: This wire will register ( + ) voltage

+)

in

all positions

of

the ignition

switch.

Connect the RED wire to the constant 12 Volt battery wire.

the

of

the

NOTE: Remove all fuses until all connections are made.

3 ORANGE

ACCESSORY 1 ( + )

Locate the vehicle's accessory wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to

(Accessory) and the ON (or RUN) position. The voltage drops out key is turned to the START (or CRANK) position.

Connect the ORANGE wire to the vehicle's accessory wire.

ACC

when

the

8

ca6554 Install revA

( + )

4

PINK/WHITE

IGNITION

2

Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped).

Verification:

RUN) position, but not the

This wire registers voltage when the key is turned to the

ACC

(Accessory) position. The voltage does not

drop out when the key is turned to the START (or CRANK) position.

ON

(or

Connect the

Programmable output:

5

RED/WHITE BATTERY 12V (

Locate 1

Verification:

PINK/WHITE wire to the vehicle's ignition 2 wire.

IGN,

ACC,

Start.

+)

the vehicle's constant 12 Volt battery wires at the ignition switch.

of

all positions

This wire

register ( + ) voltage

will

in

switch.

Connect the RED/WHITE wire to the constant 12 Volt battery wire.

NOTE: Remove

6

PINK IGNITION 1 (

all

fuses

until all connections are made.

+)

Locate the vehicle's ignition wire at the ignition switch.

the ignition

of

Verification:

This wire registers voltage when the key is turned to the

RUN) position. The voltage does not drop out when the key START (or CRANK) position.

Connect the

PINK

This wire is also

wire to the vehicle's

used for

Ignition

1

Ignition

Output.

wire.

ON

turned to the

is

(or

Voxx Electronics

2014

Corporation.

All

rights reserved.

9

6

Output

Harness

1

Locate the vehicle's horn wire.

Connect the BROWN/BLACK wire to the output, 200mA.

2

This wire provides a and remains used for the

BROWN/BLACK

Verification:

ground when the horn switch is pressed.

BLUE/BLACK

until4

multiple application's a

control module.

This wire

(-)

seconds after the remote start

will

200mA

HORN

register at positive voltage

START STATUS

output when the remote start function is activated

1 amp diode

OUTPUT (

vehicle's

is

required

- )

and register

horn wire. This is a

I

ACTIVE OUTPUT

is

shutdown. If

in-line

this wire

with the stripe facing

low

current

(

- )

will

be

3

This wire provides a optional

To selectable options for timing.

4

Locate the

This is a

VIOLET/BLACK AUX 1

(-)

200mA

accessories (i.e. Power Window/Sunroof, etc.).

activate refer to the transmitter button configuration chart. Please

RED/WHITE TRUNK

vehicle's

Verification:

the trunk

low current

trunk release

This wire will

release

is

200mA

activated.

output and

output

wire at the trunk

register either positive

capable

RELEASE

in

configurable

of

driving relays.

release

OUTPUT (

switch.

voltage or ground when

in

option programming.

For

refer to

- )

Control

the

of

10

ca6554 Install

revA

5

GREEN/BLACK

LT

FACTORY DISARM PULSE

BEFORE

START

I

- )

(

This wire

will supply

a

200mA pulse

(-)

both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter alarm from the key

cylinder

Verification:

position in the driver's door

Connect the

6

ORANGE GROUND WHEN ARMED OUTPUT ( - )

This wire

This wire is modules

LIGHT

have a continuous

will

typically additional

or

This output can be configured

inside the drivers door.

This wire registers ground if the key is turned to the unlock

cylinder.

GREEN/BLACK wire to the factory

output when the system

the starter interrupt relay

used for

500mA

(-)

controlling

alarm

disarm wire.

is

well

as

sensors.

option programming.

in

disarm wire

Armed.

as window

1

This wire is a

2

Locate the

BLUE/WHITE INSTANT TRIGGER INPUT ( - )

GROUND

Verification:

This wire when connected

input for

GREEN

vehicle's dome light

Verification:

This wire and the interior door is

closed

light

and the interior

will

is on. This wire

Connect the GREEN wire to the

NOTE:

Certain

application

vehicles may require

guide.

external

an

DOOR TRIGGER INPUT

sensor or secondary pin switch.

trigger the security system.

will

(-)

or door pin switch wire.

register ground (NEG) when the door

voltage

light

will register positive

is off.

vehicle's negative door input wire(s).

multiple

connections. Refer to vehicle

opened

is

when the

2014 Voxx

Electronics

Corporation.

11

3 PURPLE

DOOR

TRIGGER

INPUT

(

+ )

Locate the

vehicle's

Verification:

dome

light

This wire

will

opened and the interior

register ground

or

"0" Volts when the door is closed

or

light

off.

Connect the PURPLE wire to the

NOTE:

application

4

This wire it from an

Certain

vehicles

guide.

WHITE/BLUE

will

activate the Remote

external device.

may require

door pin switch wire.

register positive

is on. This wire

voltage (POS)

will

when the

and the interior

vehicle's positive door input wire(s).

multiple

connections. Refer to

EXTERNALSTARTINPUT(-)

Start

function when a

GROUND

vehicle

pulse

door

light

is

applied

is

to

5

Install for Remote

GRAY

a Hood Pin

Start.

Verification:

vehicle's

hood is opened.

HOOD PIN INPUT (

Switch

and connect to the GRAY wire. This connection is required

This wire when connected

Connect the GRAY wire to the hood pin.

NOTE:

6

Locate the

Be sure to loom

GRAY/RED

vehicle's

Verification:

This wire

the wire, and

seal

PARKING

parking brake wire.

will

register ground when the

BRAKE is engaged.

NOTE:

The

following connection is required for

will

register ground when the

the grommet.

BRAKE

Manual

- )

INPUT

(-)

vehicle's PARKING

Transmission Mode.

12

ca6554

Install

revA

7

BROWN/RED

BRAKE

INPUT (

+ )

Locate the vehicle's brake light wire at the brake pedal mounted switch. This connection is required for remote start.

Verification:

This wire registers positive voltage when the brake pedal

pressed.

Connect the BROWN/RED wire to the vehicle's brake light wire.

is

8

PURPLE/WHITE

TACH

INPUT

Locate the vehicle's ignition coil or fuel injector

procedure:

1.

2.

3.

4.

5.

Verification:

voltmeter to AC VOLTS.

Set

Test using the

Attach positive lead Attach negative lead

Start

the engine.

of

following

a volt meter to a constant 12 volt source.

a volt meter to the wire to be tested.

Have someone press on the gas pedal slightly as you monitor the meter. connected to the correct wire, the voltage reading will increase as the engine's RPM increases.

Connect the

PURPLE/WHITE

wire to the negative side

fuel injector.

the engine compartment.

in

the vehicle ignition coil or

of

If

2014 Voxx Electronics Corporation.

All

rights reserved.

13

4 Pin Alternate Output Harness

1

This wire the remote start feature is activated. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door.

This output can be configured

2

This wire successful completion re-lock the vehicle's doors upon remote start if necessary.

L T GREEN/BLACK

will supply a ( - )

Verification: This wire registers ground if the key

position in the driver's door cylinder.

LT

BLUE

will supply a

200mA

in

( - ) 200mA pulse both upon arming the system and upon

of

the remote start activation sequence and is typically used to

FACTORY DISARM PULSE

pulse both upon disarming the system and when

option programming.

FACTORY ARM PULSE

BEFORE

AFTER START

I

START

is

turned to the unlock

(

- )

I

( - )

This output can be configured

3

This wire will

is shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle's accessories from remaining on after remote start shutdown.

This output can be configured

4

Locate the vehicle's second starter (crank) wire at the ignition switch. (if equipped)

This wire

programming.

GREEN/WHITE

supply a

typically used to re-lock the vehicle's doors if they unlock upon remote start

BLACK/YELLOW

Verification: This wire registers voltage only

the ignition switch.

will

supply a ( - )

( - )

in

200mA

in

option programming.

200mA

option programming.

PULSE

pulse after the remote start shuts down. This

PULSE DURING CRANK

output and can be configured in option

AFTER

in

SHUTDOWN

the start (crank) position

(

- )

(

- )

of

14

ca6554 Install revA

1

PINK/BLACK

AUXS

driving

This wire provides a ( - ) 200mA optional

activate refer to the transmitter button configuration chart.

To selectable

2

This wire provides a ( - ) optional

activate refer to the transmitter button configuration chart.

To selectable

3

This wire provides a ( - ) optional

accessories (i.e. Power Window/Sunroof, etc.).

options for timing.

ORANGE/BLACK

200mA

accessories (i.e. Power Window/Sunroof, etc.).

options for timing.

GRAY/BLACK

200mA

accessories (i.e. Power Window/Sunroof, etc.).

output capable

AUX4

output capable

AUX3

output capable

of

driving

of

driving

of

relays.

For

Please

For

Please

refer to the

relays. For

Control

of

activate refer to the transmitter button configuration chart. Please

To

selectable

4

This wire provides a ( - ) optional

activate refer to the transmitter button configuration chart. Please

To selectable

options for timing.

WHITE/BLACK

200mA

AUX2

output

capable

of

accessories (i.e. Power Window/Sunroof, etc.).

options for timing.

driving

relays. For

refer to the

Control

of

refer to the

Electronics

Voxx

2014

Corporation.

All

rights reserved.

15

3 Pin Lock Output Harness

1 BLUE

3

The door

GREEN

lock

I

unlock

outputs are designed to control several systems which may require chart to see which type types are shown

These wires

Negative

All

Door Lock and

Switching

in

supply

Unlock:

the

following

a

( - )

Locks

of

switch.

UNLOCK

LOCK

additional

door

lock

parts.

system

diagrams.

SOOmA

output.

Locate the lock

(-)

Please

is

in

I

unlock wire at the

review the wire and location

your

vehicle.

different types

of

The most common

vehicle's lock

I unlock

Verification:

These wires

will register ground when the Lock and

switches are activated.

Connect the GREEN and BLUE wires shown

Negative Locks:

GREEN ( - ) Lock

BLUE (

- ) Unlock

in

the diagram

Output

Vehicle

Control Relays

Output

Unlock

below.

Door Lock

16

ca6554

Install

revA

Positive Switching Locks

Door Lock and Unlock: Locate the lock

All

switch.

unlock wire at the

I

vehicle's

lock

unlock

I

Verification: These wires

will register

positive voltage when the Lock and

Unlock switches are activated.

Connect the GREEN and BLUE wires shown

Positive Locks:

Door Lock

Vehicle

Control Relays

Reverse Polarity

Locks ( 5-Wire

Door

locks)

the diagram below.

in

GREEN ( - ) Lock

Unlock Output

- )

BLUE (

Output

Door Lock and Unlock: Locate the lock

All

unlock wire at the

I

vehicle's

lock

unlock

I

switch.

Verification: These wires will rest at ground and register positive

voltage when the Lock and Unlock switches are activated.

Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below

using (2)

SPOT

relays (not supplied).

Reverse Polarity Locks:

GREEN ( - ) Lock

Output

Voxx Electronics

2014

Corporation.

Cut

17

Negative

Multiplexed

Locks

All Door Lock and Unlock: Locate the lock

I

unlock wire at the vehicle's lock

switch.

Verification:

This wire

will

show variable ground when the switch is activated .

Please consult the wire and location chart for specific resistor values for

your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown using (2)

SPOT

Multiplex

relays (not supplied).

Locks:

Vehicle

Control Relays

I

unlock

in

the diagram below

BLUE ( - )

Unlock Output

Door Lock

Positive Multiplexed

All Door Lock and Unlock: Locate the lock

Locks

I

unlock wire at the vehicle's lock

switch.

Verification:

This wire

will

show variable positive voltage when the switch

activated. Please consult the wire and location chart for specific resistor values for your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown using (2)

SPOT

relays (not supplied).

Multiplex Locks:

I

unlock

in

the diagram below

is

18

----t~t-----..

Vehicle

Door Lock

Control Relays

ca6554 Install

revA

Adding Aftermarket Actuators

After

installing

wires shown

aftermarket actuators, (not supplied). Connect the GREEN and BLUE

the diagram below using (2) SPOT relays (not supplied).

in

+12Vdt

----t-------t

87

-------~-----1

Fused Battery Source

Fused +12

Battery Source

Volt

BLUE ( - )

Unlock

Output

2014 Voxx

Electronics Corporation.

19

Additional Ports

Antenna

Mount the

will

not

I

LED

I

Programming Port

supplied antenna/receiver to a clear

spot on the

block the driver's vision. A good location

is usually

vehicle's windshield that

high on the

near the rear view mirror. Be careful not to mount the antenna/receiver metallic cable to the control module

window

film,

as this

will

effect system range. Route the antenna/receiver

and

plug

into the antenna port.

Data Bus Interface Port

This 4 pin port is used for to communicate with the

Flashlogic

be

available. Please

Door Lock and Transponder Interface modules the

Flashlogic

vehicle's

Door Lock and Transponder Databus

Databus. When using the DBI port to

refer to the D2D (Data to Data) function

following options may

list available

on the tech service web site.

windshield

on

any

Interfaces

control the

per

vehicle

Tach Input Door Trigger Door Lock Control Dome Light Supervision Factory Manual

Alarm

Arm

I

Arm

Disarm

Telematic Interface Port

This 4 pin port is used for

Pro, which can

Door Lock Sliding

control

some

Control Trunk

Doors AUX Output

Car Find Remote Start

Brake Safety Shut Down

Trunk/Hatch Open

Passlock

Transponder

I

Disarm

Inputs

Diesel Glow Plug Input

(factory keyless controls

telematic Interface

of

the

following

I

Passkey Interface

Interface

Activation

(GM

Only)

system)

accessories, such as Car Connection

features.

Release

20

ca6554

Install

revA

Set

Up

&

·

r:-rogramrni

.

ng

Transmitter Programming - Feature Bank 1

1.

2.

3.

4.

5.

6.

NOTE: NOTE:

system.

NOTE:

transmitter will

NOTE:

ignition system.

Turn

the ignition

Press Within Press 1 button The system Pressing the override button at anytime during programming

the next bank.

and

The system This system has 1 button programming which programs all channels

The system

This system has

is

turned

ON.

hold the valet/override

10

seconds the system will

of

each transmitter you wish

will

respond with 1 chirp for each accepted transmitter.

will

exit transmitter programming after 15 seconds of inactivity.

will hold

erase the

ON,

the LED

up

to 4 transmitters

oldest

PTN

transmitter

- Programmed Transmitter Notification. Each time the will

button.

chirp (3) three times.

to

program.

will advance

of the

in

memory, programming a

in

memory.

flash the number of transmitters programmed

5th

to

the

Transmitter programming for 2 Car Mode *2 way system

1.

2.

NOTE:

vehicle.

Manual

1.

2.

3.

4.

5.

Enter the transmitter into 2 Car

owners Follow the steps above for transmitter programming.

2

manual

car mode requires

for 2 car operation)

an

additional

Mode. (Refer

security system installed

to

transmitter operation

Feature Programming - Feature Bank 2

Turn

the ignition

Press

Within

Use the feature programming advance to Feature Bank four,

Use the transmitter feature

and

hold

10

seconds the system will

valet/override

(5) five, (6) six and (7) seven chirps.

book, the system

ON.

the valet/override

button to advance through each option bank. For

0

button

will

chirp

button.

chirp (3) three times.

2,

3,

to

scroll

to

through the selections

match the feature number.

- 5

4 or

only:

5,

in

a second

which is

in

each

in

(4)

the

6.

2014

Voxx Electronics Corporation.

Press the transmitter flash indicating the changed feature.

All

i

button

rights reserved.

to

change the desired feature. The

LED

will

21

Defaulting All Features:

default

banks

NOTE:

will

The system

will

is on, there is no time

Chirps

3

•

1

Bank

Feature

Transmitter

Programming

Pressing the

features

all

remain

To

limit.

in

exit programming turn the IGNITION

Refer to transmitter programming.

a button anytime

while

and return you to feature bank

feature programming mode as

long

any of the feature

in

4 chirps.

2-

as the ignition

OFF.

Arm/Disarm

10

Chirp

I

Pati<ing

Light Pattern

22

1-

Disarm

ca6554

Install

revA

2014

Voxx

Electronics

Corporation.

23

Yellow Output

I

4 Black

24

Ground Running

While

Ignition Accessory

ca6554

Install

revP

Tach Programming

The unit

turned ON.

programming tach, the unit been learned and stored.

will

not operate

If

an

attempt

unless

is

made

will

If

the tach rate is not properly programmed

tach is programmed or

to

start the vehicle via the remote start without first

flash the parking lights 7 times indicating tach

vehicle, the unit may not realize that the vehicle is running

re-engage the starter motor.

The Remote Start unit

packs, or single injector.

1.

2.

3.

4.

5.

Turn the ignition key to the Press and release the valet/override button 3 times. Immediately turn the ignition key Press and hold the valet/override button, then start the

the

key.

When the unit senses the tach signal, the parking lights

will

learn the tach rate

To

learn tach:

ON

of

most vehicle's single

position.

OFF.

flash.

6.

Allow

the vehicle

to

settle to a normal idle speed.

tachless

option

to

in

certain instances

coil, multiple

vehicle

will

begin

is

has

not

the specific

and

coil

using

to

7.

NOTE:

poor tach source, the parking connect the PURPLE/WHITE wire

Release the valet/program push-button switch. The parking lights

turn

on

tach

If

the unit

for 2 seconds and 1 long chip

signal

is

stored and the unit has exited tach learn mode.

fails to learn tach rate due to

lights will not flash.

to

the proper tach signal, and then repeat the tach

will indicate that the learned

an

improper tach connection or a

To

correct this situation, locate and

will

learn routine.

Smart

Smart system and when activated

Tach

less

Mode

less Mode

is

available only if a tach signal has never been learned

will

automatically change the Tach Mode feature

to

in

option

the

programming to Tachless without the need to enter the feature programming mode.

1.

Activate the remote start. The parking lights should begin flashing

7

times indicating no tach signal has been learned.

2.

3.

Within the 7 flash time period, press and The system will

mode.

2014

Voxx

Electronics

Corporation.

hold

the

chirp 1 time indicating the system

0

is

button.

now

in

tachless

25

Adjusting the

Shock Sensor

1.

2.

Increase Decrease sensitivity by turning the adjustment dial

Testing the

Arm the system and wait 6 seconds for the zone vehicles

Chirp

System ARM/DISARM chirps can

programming feature banks.

bumper.

Delete

1.

2.

sensitivity by turning the adjustment

Shock

Sensor

- User Accessible

toggled

be

OFF.

then

Turn the ignition Press and

respond with 1 chirp for

will

release

ON

the valet/programming button 3 times. The system

ON

or 2 chirps for

dial clockwise.

counter

stabilize,

to

without entering the

OFF

or

OFF.

clockwise.

then

firmly

strike the

Dome Light

The system can

second max) for

(60 Once seconds before arming.

programed the system will 'learn'

1.

2.

3.

4.

Delay

be

Close all Using the transmitter press

UNLOCK, LOCK. The LED entered

Immediately OPEN system. The system will dome the learning

The LED

learning mode and

I

programed to delay

vehicles

doors with ignition off.

DOME

light

will

Theater Dimming

arming after the

with a

DELAY LEARN

turns off, the system

mode.

begin to flash

dome

the timing of the dome

LOCK, UNLOCK, LOCK ,UNLOCK, LOCK, will light solid

then CLOSE

then monitor the door trigger wire.

indicating the system has exited the

now armed.

is

button is pressed

lock

light delay

MODE.

the door

then add 2 seconds and then exit

will

or theater dimming feature.

light delay

to indicate the system has

WITHOUT disarming the

and add 2

Once the

26

ca6554

Install

revA

Feature Bank

1

-Silent

2

-

Passive Locks:

Choice:

ON

-

Silent unlock system

a second time

will only

lock/unlock buttons. OFF

-

normal arm/disarm chirps upon the first press

Active - Requires use

2-

Security

Controls

the

normal

arm/disarm chirps

arming/disarming upon first press of

will activate the arm/disarm chirps

sound the arm/disarm chirps upon a second press

Determines

manual

of

the transmitter to

or automatic

lock

of

the security system.

lock/unlock, pressing

respectively.

of

lock/unlock.

locking

the

of

the

vehicle's

doors.

of

lock/

The

the

doors.

Passive-

is

closed. Note: For Passive Locks, feature #3 Passive Arming must

Automatically locks the

vehicle's

doors 1 minute after the

set to passive

3

-

Passive Arming:

Determines

manual

or automatic

locking

of

Active - Requires use of the transmitter to arm the security system.

4-

Passive - Automatically is

closed.

Siren

I

Horn:

This feature

arms the security system 1 minute after the last door

selects

which output(s)

will sound the system's

arm/disarm chirps. This feature does not effect the triggered state

system and during a triggered

cycle,

both the siren and horn outputs

respectively.

5-

Siren

Duration:

This feature

controls

the length

of

time the system will

when triggered.

the

vehicle's

of

the security

will

activate

last door

also

be

doors.

sound

6 -

Security:

ON OFF-

Controls

-

Full

security

security functionality

The security system does not trigger. Panic, Remote

other convenience features operate as

7- Anti-Hijack Mode:

OFF

- Standard security system operation.

ON

- Enables Car

Controls

manual.

2014

Voxx

Electronics

Corporation.

functionality.

car jack

Jack mode

-

ON

normal.

mode-

functionality

I

OFF.

ON

I

OFF.

as described

Start and all

in

the owners

27

Orange Output:

Ground

8-

This wire

Port Protocol:

OBI

9 -

While Armed

either supply a

will

I

( - ) output when armed

Determines the protocol type

interface with external modules.

Protocol

OBI

Protocol

ADS

Parking Light Pattern:

Arm/Disarm Chirp

10-

and parking light

flashes when the system

I

Standard - 2 chirps/light flashes with arm, 1 chirp/light flash with disarm. Inverted - 1 chirp/light flash with arm, 2 chirps/light flashes with disarm.

Controls the output

disarmed.

OR

which the

in

Determines the number

armed/disarmed.

is

the orange wire.

of

port uses to

OBI

chirps

of

Feature Bank 3 - Output

Extended Lock

1 -

Pulse:

Control

Controls the timing of the BLUE and GREEN lock output

wires.

Second

1

- Single

3.5 Seconds Second Lock,

1 second

30 Second 1 second

unlock pulse.

Lock, Double Pulse

unlock pulse.

1 second

Single 3.5 second lock pulse, single 3.5 second unlock pulse.

Double

Double Pulse Lock, 1

Second

lock pulse, single

Pulse Unlock -

Unlock

Unlock - Double 1 second lock pulse, single 1

Single 1 second lock

- Single 30

second unlock pulse.

Factory Disarm:

2 -

the 6 pin output harness only and does not change the output

on

wire

Controls the timing

of

LT.

the

disarm wire on the 4 pin alternate output harness.

1 second unlock pulse.

pulse,

second lock pulse,

double 1

double

GREEN/BLACK factory disarm

the factory

of

Factory 2nd Unlock -

Disarm-

Same

Factory Disarm

continuous ( - ) output during the remote start cycle.

Factory Disarm activation.

28

Single

1 second pulse with unlock and remote start activation.

output as unlock with 2nd press

Single 1 second pulse with unlock and

Start Status

I

Single 350mS

Single 500mS

-

second pulse with unlock and remote start

unlock.

of

ca6554

Install

revA

3 -Ignition

or

OFF.

Controlled

Locks: Control

of

door

locks when the ignition is cycled

ON

OFFLock and Unlock - Doors

Door

locks

not activated by ignition.

lock

when ignition

ignition is turned off. Lock Unlock

Only-

Doors

lock

when ignition is turned on.

Only - Doors unlock when ignition

4 - Trunk Output Timing - Red/White Output:

RED/WHITE

1

Second Pulse

1

0 Second

20

Latched

output.

-

1 second

pulse output.

- Continuous output for 1 0

Seconds - Continuous output for

until IGN ON

- Continuous output

seconds.

20

seconds.

ON. Latched

is

pressed again.

ON until

Button Press - Continuous output

is

turned

is

turned off.

on

and unlock when

Controls the output timing/type of the

until

the vehicle's ignition is turned

until

the activation button

5 - Horn Output Timing:

some

6-

vehicle will

16mS

Real

Panic:

ON-

require a longer

1

OmS

Controls the horn output when the system

Randomized horn honks when panic

OFF - Standard pattern horn honks when panic is triggered.

7

- AUX

1:

Controls 1 Second LatchedLatched

the

VIOLET/BLACK

Pulse -

Single

Output stays active until

until IGN ON - Output stays active

Dome Light Output by

the AUX 1 function

Control

the minimum horn

pulse

to activate the factory horn.

30mS 40mS 50mS

is

AUX 1 output activation type and timing.

1 second pulse.

button is pressed again.

until the ignition is turned on.

Output

of

used for

illuminated

the transmitter.

pulse

time

is

triggered.

entry and is not

in

milli seconds,

controlled

Defrost Output Defrost Output

Single Pulse Latched 5 Minutes -

remote start.

-

Single

1 second pulse after start

5 minute continuous output after

29

8

AUX

-

Controls

2:

the WHITE/BLACK

AUX

2 output activation type and timing.

9-

1 Second Latched Latched until

Second

0

1

lock

of

Second

10 press

AUX

3: Controls the GRAY/BLACK AUX 3 output activation type and timing. 1 Second Latched-

Pulse-

Output

IGN ON

Pulse

button.

Pulse

unlock button.

of

Pulse

- Single 1 second

Output

Latched until IGN ON -

0 Second Pulse with Arm -

1

button.

lock

of

unlock

of

Pulse

button.

Second

10 press

Single

1 second

stays active

Output stays active until the

-

with Arm -

Output

with Disarm -

pulse.

button is pressed again.

until

stays active for 1

Output

pulse.

button is pressed again.

stays active

Output

until

stays active until the ignition is turned on.

Output

stays active

with Disarm - Output

ignition is turned on.

0

stays active for

0

for 1

stays active for

seconds with press

10 seconds with

seconds with press

seconds with

10

10-

11

AUX

4:

1 Second

Controls

the ORANGE/BLACK AUX 4 output activation type and timing.

Pulse

- Single 1 second

Latched - Output stays active until

Output

Latched until IGN ON

1 0 Second

lock

of

1 0 Second

press

AUX

-

1 Second LatchedLatched

0

1

lock

of

Second

1 0 press

5:

Second

Pulse

button.

Pulse

unlock button.

of

Controls

Pulse Output

untiiiGN

Pulse

button.

Pulse

unlock

of

the

-

button.

-

with Arm -

with Disarm - Output

PINK/BLACK

Single

1 second

stays active until button is pressed again.

ON-

Output stays active until the ignition is turned on.

with Arm -

with Disarm - Output

pulse.

button is pressed again.

stays active

Output

stays active for 1 0

AUX

pulse.

Output

stays active for 1 0

the ignition is turned on.

until

seconds with press

stays active

for 1 0

seconds

with

5 output activation type and timing.

seconds with press

stays active for 1 0

seconds with

30

ca6554 Install

revA

Feature Bank 4 - Remote Start Control

1 ·

RF

Start

2

• Run Time: Controls the time

control of the remote start until the system times out. The system may also be shut

down at any time by use

3

• Running Lights: Controls the

start.

Chirp: Turns remote start activation confirmation chirps

in

minutes that the vehicle will

of

the transmitter or system shutdowns.

WHITE

parking light output wire during remote

stay running under

ON

or

OFF.

Steady - Parking lights constant during the remote start

cycle.

Flashing - Parking lights flash at a slow pace during the remote start cycle.

4

·

Tach Mode: Determines how the system monitors the engine running during

remote start.

Tach

- Hard wired directly to the tach wire of the vehicle to monitor

voltage. Tach

less (Crank Average/Voltage) - Determines crank time by averaging the

last 8 times the vehicle was started with the key and then monitors the

change

Hybrid (Crank Average

the last 8 times the vehicle was started with the

OBI connected to the

5

·Voltage Level:

in

Port-

voltage after remote start.

I

No Voltage)- Determines crank time by averaging

key.

Monitors the vehicle's tach rate through an interface module

OBI

port.

The voltage variance for remote start when set to tachless. (see

tach mode)

AC

HIGH-

The variance

is activated to after the engine is running must LOW - The variance

is activated to after the engine

6

•

Crank Time: Preset output times for the PURPLE starter wire.

7

•

Crank Average

I

Crank Time: The length of time

crank the vehicle's starter.

Crank Average - Determines crank time by averaging the last 8 vehicle was started with the

Preset

2014 Voxx Electronics Corporation.

Time-

Preset starter output time. (see crank time)

in

battery voltage from before the remote start

be

greater than

in

battery voltage from before the remote start

is

running may

be

less than

in

which the remote start

key.

0.5

volts.

0.5

volts.

times the

will

31

8-

Gas

Diesel:

I

Selects engine type and

remote start activation.

delay time for the starter output wire during

Gas -

Second

10

Gasoline

engine, no

Delay

Diesel

-

seconds after the ignition has been powered up by the remote start.

Diesel

15 Second

Delay

-

seconds after the ignition has been powered up by the remote start.

Second

20

Delay-

Diesel

seconds after the ignition has been powered up by the remote start. 45 Second

Delay-

Diesel

seconds after the ignition has been powered up by the remote start.

Double Pulse Start:

Single

9 -

single

- Ignition 2 Output Pnik/White:

10

I

or double

Ignition

2

press from the transmitter.

Output

-

becomes active with the same timing as the ignition

output and does not drop out during crank.

delay

engine, delays

engine,

for the starter output wire.

the starter output wire for 1

the starter output wire for

delays

the starter output wire

the starter output wire for 45

0

15

for 20

Switches the remote start activation between a

Programmable

high current output.

Accessory -

Output

becomes active with the same timing as the accessory

output, drops out during crank.

Start

Crank -

I

Output

becomes active with the same timing as the starter

output wire, during crank only.

- 2 or 3 Hour Start:

11

When activated, the remote start

programmed time and shut down every 2 or 3 hours.

Turbo Timer:

12-

When activated, the

vehicle will

run for the programmed time.

OFF 1 Minute 3 Minutes 5 Minutes

remote start activation based on the

13 - Transmission Mode:

vehicle's

transmission type.

Select

the type

of

Automatic - For use with automatic transmission start operation.

Manual-

For use with

must be set upon exit

manual

vehicle

of

transmission

to enable remote start.

vehicles.

activate and run for the

will

vehicles. Standard remote

Remote start ready mode

Temperature Start:

14-

When temperature start is activated, the remote start function

ambient temperature drops below

32

Sets the

threshold

temperature for temperature start mode.

the selected temperature.

activate when the

will

ca6554

Install revA

15 -Accessory Output: Programmable high current output.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.

Start

I Crank - Output becomes active with the same timing as the starter

output wire, during crank only.

16-

Pulse Additional Outputs

w/

Unlock: When the Unlock button is pressed

on the remote transmitter the system will also simultaneously pulse additional outputs. Ignition, Accessory & Ground While Running outputs for 1 second. The 3rd setting also activates the pulse after shutdown output to turn off the RAP on certain vehicles.

OFF

-When

IGN, ACCY,

simultaneously pulse the Ignition, Accessory

Unlock is pressed

GWR-

When the Unlock button is pressed the system will also

no

additional outputs are activated.

& Ground while Running outputs

for 1 second.

IGN, ACCY, GWR, then Pulse After Shutdown - When the Unlock button

is pressed the system will also simultaneously pulse the Ignition, Accessory & Ground while Running outputs for 1 second then waits 2 seconds then pulses the green/white pulse after shutdown wire for 1 second.

17 - Door Lock Control During Remote Start: Controls the systems door lock outputs

during the remote start sequence.

OFF-

Unlock before Start, Lock After

The system will not lock or unlock the vehicle.

Start-

Unlock Pulse before remote start sequence begins, Lock pulse after remote start sequence is complete and engine is running.

Unlock Before Start - Unlock Pulse before remote start sequence begins. Lock After

Start-

Lock pulse after remote start sequence is complete and

engine is running. Lock After Shutdown - Lock pulse after remote start shutdown sequence is

complete.

33

Feature Bank 5 - 4 Pin Alternate Output

1 - Lt Green/Black Output: Controls

and timing.

Pulse

before

activated.

Start

Also a

During

I

1 second

Unlock

pulse when unlock is pressed.

Control

GREEN/BLACK output activation type

LT

the

1 second pulse when remote start is

-

2

Ground

While

sequence Ignition- Output

Running - Continuous output for the entire remote start

until

after the

vehicle

shuts down.

becomes active with the same timing as the ignition output

and does not drop out during crank. Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank. Pulse

During

Crank

starter output wire, during crank

Output: Controls

Blue

- Lt Pulse After

Start sequence and has confirmed the when

Ground sequence

lock is pressed.

While

Running - Continuous output for the entire remote start

until

Ignition- Output

- Output becomes active with the same timing as the only.

BLUE output activation type and timing.

LT

the

During Lock - 1 second pulse after the remote start

I

1 second

a

after the

vehicle

is

shuts down.

running. Also

becomes active with the same timing as the ignition output

and does not drop out during crank.

pulse

Accessory-

Output becomes active with the same timing as the accessory

output, drops out during crank. Pulse During

Crank

starter output wire, during crank only.

- Green/White Output:

3

timing.

Pulse After Shutdown shutdown.

Ground While Running - Continuous output for the entire remote start sequence until after the vehicle

Ignition-

Output

and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank. Pulse During

Crank

starter output wire, during crank only.

- Output becomes active with the same timing as the

GREEN/WHITE output activation type and

Controls

the

2 second pulse after the remote start has

shuts down.

becomes active with the same timing as the ignition output

- Output becomes active with the same timing as the

34

ca6554 Install

revA

4 -

Black/Yellow

timing.

Output :

Controls

the BLACK/YELLOW output activation type and

Pulse

starter output wire, during crank only. Ground

sequence Ignition - Output becomes active with the same timing as the ignition

and does not drop out during crank. Accessory-

output, drops out during crank.

Transmitter·

During Crank

While

Running - Continuous output for the entire remote start

until

after the

Output becomes active with the same timing as the accessory

Button

- Output becomes active with the same timing as the

vehicle

shuts down.

Functions

output

2014 Voxx Electronics

Corporation.

All

rights reserved.

35

36

ca6554 Install

revA

Security Trigger Zones

If the security system has been triggered the LED will flash one of the patterns below

indicating the zone.

LED

FLASHES

TRIGGER

ZONE

2 Flashes

3 Flashes 4 Flashes 5 Flashes

Hood Door

I

Input Shock Sensor Ignition Input

Remote Start Shutdown Diagnostics

If

the remote start shuts down or fails

patterns below indicating the shutdown input. To

manually enter diagnostics

press and release the

LED

FLASHES

._.

and

button.

to

start, the parking lights

view the last shutdown, turn the ignition

SHUTDOWN

Trunk

Input

ZONE

will

flash one

of

ON

the

and

3 Flashes

Hood

Input Brake Input Neutral

4 Flashes Remote

Safety Input

Start Valet Mode

5 Flashes Manual Transmission Mode not set (manual

transmission models only}

7 Flashes

Tach

not learned

I

Crank Average not learned

2014

#4120290

BLUE/WHITE GREEN PURPLE WHITE/BLUE GRAY GRAY/RED BROWN/RED PURPLE/WHITE

SHOCK SENSOR PORT

TELEMATIC PORT

-

(

INPUT

)

INPUT

+ )

INPUT ( -

(-) (

(-

TRIGGER

INSTANT

TRIGGER

DOOR

TRIGGER

DOOR EXTERNALSTARTINPUT(-) HOOD INPUT PARKING BRAKE TACH INPUT

BRAKE

INPUT

)

+ )

)

E~

n:cg

su

~

IU

Cl

0

u

#4120291

~120110

#4120145

I

04120184

#1032714

#4120102

ANTENNA LED VALET

PURPLE RED ORANGE

~

PINK/WHITE RED/WHITE PINK

WHITE/RED WHITE

0

BLACK BROWN

PINK/BLACK ORANGE/BLACK GRAY/BLACK

0

WHITE/BLACK

BROWN/BLACK BLUE/BLACK VIOLET/BLACK RED/WHITE

T GREEN/BLACK

L ORANGE

BLACK/YELLOW GREEN/WHITE

BLUE

LT

L T GREEN/BLACK

(P

STARTER BATIERY ACCESSORY

IGNITION BATIERY IGNITION

PARKING LIGHT PARKING GROUND SIREN

AUX 5 AUX AUX AUX

HORN START STATUS AUX TRUNK FACTORY GROUND

PULSE DURING

PULSE FACTORY FACTORY

~1i5l

OUTPUT12V (

(

2

12V (

(

1

LIGHT

OUTPUT

OUTPUT OUTPUT

4

OUTPUT

3

OUTPUT

2

OUTPUT

1

RELEASE

DISARM

WHEN

AFTER

ARM

DISARM

+)

+ )

(

1

+ )

+)

+ )

INPUT OUTPUT

+ )

(

)

-

(

)

( -

)

-

(

)

-

(

)

-

(

ACTIVE

I

)

-

(

OUTPUT

I

ARMED

CRANK

SHUTDOWN

PULSE

I

)

MOTOR SIDE (

OUTPUT

PULSE BEFORE START

(

-

(

AFTER

PULSE BEFORE START

+ )

)

-

(

)

-

(

)

-

)

-

(

START

-

(

)

-

(

)

-

(

BLACK

I

INTERUPT

#1024405

STARTER

87

a7a

I

86

30

ORANGE RED

I

BLACK

85

WHITE OPEN

38

RELAY

-ARMED

86

IGNITION

8587A-

STARTER

30 -

OPEN

87-

HARNESS

&

OUTPUT

STARTER

+ )

(

OUTPUT-

INPUT-

#1032714

)

-

(

MOTOR

KEY SIDE

SIDE

BLUE OPEN GREEN

PORT

OBI

CID

UNLOCK

LOCK(-)

SHOCK

RED BLACK BLUE GREEN

(-)

SENSOR

#4700023

HARNESS

&

BATIERY GROUND

TRIGGER

FULL

AWAY

WARN

+)

12V (

WHEN ARMED ( -

)

-

(

TRIGGER

ca6554

(

Install

)

-

revA

2014

Voxx Electronics Corporation.

All

rights reserved.

39

Voxx

Electronics

Corporation.

COMPLIANCE

FCC

This device

Customer Service

WWW.CODE-ALARM.COM

complies with Part 15

1-800-421-3209

the FCC rules

of

and with

RSS-21 0

of

Industry Canada. Operation is subject to the

This device may not cause

1. This device must accept any interference received, including

2. may cause undesired operation.

Warning!

Changes or modifications not compliance could

void the user's authority to operate the equipment.

PATENTED:

40

harmful

expressly

www.

voxxintl. com/company/patents

R41

following

interference, and

approved by the party

two conditions:

0-192-710

any interference that

responsible

for

ca6554 Install

revA

Deluxe Vehicle Security

and

Remote

Start System

LCD Remote Control

IMPORTANT NOTE:

applicable

SAFETY PRECAUTIONS

2014

Voxx

Electronics Corporation. All

The operation

to most vehicles.

with 2 Way Confirming

of

the Security and Convenience System

However, due to the configuration

may not

rights reserved.

apply. Please see your installing

of

some vehicles ,

dealer

as

described

for more information.

in

some functions

this

manual

AND/OR

4280593

is

Using Your Remote

Control .................................................................... 3

Arming the Security System .............................................................. 3

Passive Arming Bypass ..................................................................... 3

Bypassing the Hidden

Alarm Function ...................................................................... 3

Shock

Sensor ............................................................ 3

Disarming the Security System ......................................................... 3

Two

Stage

Door Activating Trunk Activating

Optional AUX 1

Unlock (optional)

Release (optional) ................................................... 4

(optional) ................................................. 4

Entering AUX Mode and Activating

Finder Feature ........................................ 5

Using the Progressive Using the

Personal

Car

Protection

..................................................... 4

Additional

Alarm

AUX

................................................. 5

Outputs

Programmed Transmitter Notification ................................................ 5

Valet

Eliminating Manually Car

Mode ........................................................................................ 5

Arm

Disarm Notification Chirps

I

..................................... 5

Overriding the Security System ......................................... 6

Jack Mode .................................................................................. 6

............. 4

Using Your Remote

Vehicle

Starter ....................................................... 7

Remote Start Ready Mode ................................................................ 7

Cancelling

Remote Start Remote Starting Your Remote

Start Shutdown .................................................................... 8

Entering Your Vehicle while it is Running via Remote Preheating or User

Programmable Run Time

Using the Operating the 2 I Turbo Timer Mode

Precooling

"Quick-Stop"

3 Hour

(optional) ........................................................... 1

Operating the Daily Start

Temperature Start

Remote

Start Safety Features .........................................................

Mode ..................................................................

LED and Siren/Horn lndications Additional

2-Way LCD Remote

Ready Mode .............................................. 7

Vehicle

............................................................ 8

Start .............. 8

Vehicle's Interior

the

Run Time Extension ....................... 9

I

................................. 8

Feature ......................................................... 9

Up Timer Mode .................................. 9

Start

Timer .......................................................

........................................................... 12

Control

Functions ............................. 13

0 11 11 11

LCD Remote

Control ICON's ................................................................ 15

Transmitter Button Functions .............................................................. 16

Replacing Remote Warranty

2

Information ............................................................................ 19

Control Batteries ................................................... 18

ca6554 Owners revA

Arming

To

arm the system, exit the vehicle, close parking lights will (if equipped and connected) and activated the starter disable feature. The LED status indicator

the Security System

all

flash 2 times, indicating the system is armed, has locked the doors

will blink steadily, once per second.

doors, then press the

@

button. The

NOTE:

system requires a second press response from the vehicle.

Passive

If

passive arming is enabled on your system, while the system is disarmed, press

+ system passive bypass, press the

Bypassing

To seconds press

NOTE: The system will

will be defaulted back to normal operation the next time the system is armed.

The system is equipped with a feature

of

the

@

Arming

c:J>))

,

the system

will remain

arm the system and ignore the shock sensor press

The

Bypass

will respond with 1 chirp and the LED

in

this temporally bypassed state for as long as you wish.

@

or

r£

button and the system

Shock

@

Sensor

+

c:J>))

,

the system

only change the shock sensor setting for one arm cycle and

will

called Silent

button to activate an audible arming

respond with 1 long chirp.

Choice.

will

turn on. The security

will

@

button, then within 5

If

enabled, the

return to normal status.

To

r£

exit

Hidden

Press the

alarm function. The security system siren

I

horn

Alarm

Function

c:J>))

button first, within 3 seconds press the

will be silenced

will

arm with "Hidden

if

the system is triggered.

@

button to activate the hidden

Alarm Function" in which the

Disarming the Security System

To

disarm the system press the indicating the system is disarmed and has unlocked the doors (if equipped and connected).

NOTE: system requires a second press response from the vehicle. unlock

*Throughout this manual, 'press' refers to pressing for less than 1 second; 'press and hold' refers to pressing for more than 2 seconds.

The system is equipped with a feature

If

will

activate the audible response.

r£

button. The parking lights

called Silent

of

the

r£

button to activate an audible disarming

your system is set up for 2 step unlock, a third press

will flash 1 time,

Choice.

If

enabled, the

of

2014

3

Two

Stage

Door

Unlock (Optional)

this feature is enabled on your system, pressing the

If

again within three seconds to unlock

the driver's door. Press

only doors.

Activating the Trunk Release Feature (Optional)

this feature is

If seconds

Activating the

this feature is

If simultaneously will activate wide range

installing dealer to determine the functionality

Entering

access the additional AUX outputs, AUX

To

first enter the transmitters AUX Mode. This

buttons from their standard operation to control

will open the

AUX

enabled

AUX

functions like

of

Mode

1 Output (Optional)

enabled

vehicle's

and

ri1

on your system, pressing and holding the

trunk or hatch.

on your system, pressing the

optional feature. This feature can be programmed for a

an

sunroof automation,

power window

Activating the Additional

or

your system.

of

AUX

2,

will "shift"

of

button one time

~

the remaining

ri1

buttons

ri1

and

@

please consult

Outputs (Optional)

5

AUX

2 -

and AUX

4,

AUX

3,

the functions of the transmitter

the AUX outputs.

will unlock

button for 3

you must

5,

your

AUX Mode - 1 Way transmitter: Press and

flash 1 time. AUX Mode will remain active

seconds, the transmitter LED for 15 seconds. AUX Mode will

again for 2 seconds, the transmitter LED

and

pressing times to confirm exit.

AUX Mode -

transmitter

for 15 seconds. AUX Mode

pressing

Activating outputs while AUX

AUX AUX AUX

c:J>))

LCD

lf

Press and

2:

Press and

3:

Press and

4:

Press and

5:

2 Way transmitter: Press and

again for 2 seconds.

0

screen

Hold Hold Hold Hold

will display "AU". AUX Mode

will

exit after 15 seconds

will

AUX Mode:

in

for 3 seconds.

@

for 3 seconds.

ri1

for 3 seconds.

c:J>))

for 3 seconds.

0

Hold

for 2

and

c:J>))

inactivity or by

of

for 2 seconds, the

lf

will

inactivity or by

of

0

will

remain active

flash 2

4

ca6554

Owners

revA

Using the Progressive

Car

Finder Feature

Press the

and sound 5 times at low volume, increasing

~>))

button to locate your vehicle. The system will flash the parking lights

in

volume each time the button is

pressed.

Using the Personal Protection Alarm (Panic)

Press and hold the During panic mode, the normal function

The transmitter's

option is installed).

~>))

button for 3 seconds to activate the personal protection alarm.

of

the transmitter buttons will be suspended.

@ and

To

riJ

buttons can

be

used to lock and unlock the door (if the

stop the alarm, press and hold the

~>))

button on the transmitter

again for 3 seconds. The system will automatically stop after 30 seconds.

Programmed

As a security precaution each time the vehicle's ignition is turn

light with flash the number

to identify unauthorized transmitters from accessing your vehicle. If you believe

Transmitter Notification

of

transmitters programmed into the system. This helps

on

the status LED

an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance.

Valet Mode

When valet mode is activated the status LED will light solid, and all security functions will

disabled.

To

enter or exit valet mode simply follow the 4 steps

be

outlined below:

1.

Turn the vehicle's ignition

2.

3.

4.

Eliminating

Push and hold the programming/valet button.

The LED will turn

on

Release the programming/valet button.

Arm

I Disarm Notification Chirps

System ARM/DISARM chirps can

ON.

solid when valet mode

be

toggled

ON

or OFF without entering the

is

active

programming feature banks.

1.

Turn the ignition

2.

Press and release the valeUprogramming button 3 times. The system

will respond with 1 chirp for

ON

then

OFF.

ON

or 2 chirps for

OFF.

5

Manually

Overriding the Security

System

Your system can be disarmed without the use

since you will need the

by-pass the

To

battery

fails.

ability

to operate your

alarm

system;

the transmitter. This is necessary,

of

vehicle

if the transmitter is

lost

or

its

1.

Open

the

2. Turn the ignition key to the Within 10 seconds, press and

system will

The

3.

alarm

start and operate the

Car

Jack

Mode

vehicle

door. The

alarm will

position.

ON

release

stop sounding and enter the (by-passed) mode. You can now

vehicle normally.

sound.

the

This feature must be turned on in system programming,

installing dealer. Triggering

Jack mode:

Car

While

2 seconds, the parking lights will

1.

50 seconds after being triggered the siren will

during this 15 seconds you

Jack mode.

turn off will

Car

advance to the next step.

the ignition is

flash 1 time and the system

will

If Car

Jack mode

ON and press and

alerted

be

valet

push button switch.

please consult your

+

hold

act as follows;

will

chirp

to push the

not turned off at this time it

is

for 15 seconds,

valet

@

button to

ri3

for

2.

3.

OVERRIDE

and press the valet

On

then

Following

go

will

the 15 second chirps

sound and the parking

full

into

90 seconds after trigger

activate the starter

system STATE UNTIL

THE SYSTEM

will

THE BATTERY

TO TURN

button within 10 seconds.

seconds) the siren

(total

time now

65

lights will start flashing.

addition to the siren and parking

in,

THE SYSTEM

kill.

WILL REMAIN IN THIS

IS DEPLETED.

OFF CAR

JACK

MODE: Turn the ignition

lights,

the

OFF

6

ca6554

Owners

revA

Remote

Start

Ready Mode

manual transmission.

must

be enabled

your

if

vehicle

equipped with a

is

Remote

activate

To

Start

the

Mode. Follow

1.

2.

3.

4.

5.

Ready Mode - Manual Transmission Vehicles

remote start function, the system must first be

Only

Remote

in

the steps below to enter remote start ready mode.

While the engine is running by the ignition key;

the parking brake

Set

a.

neutral.

b. Place the transmission

in

With your foot off the brake pedal, press and release the

flash 3 times and the parking

times within 2 seconds. The LED

lights will

turn on to confirm the system has entered quick stop mode.

Remove the keys from the ignition, the vehicle

will

remain running in

will

quick stop mode.

vehicle doors.

Exit the vehicle and close

step

Within 1 minute

of

doors. The vehicle will

all

button to lock the vehicle's

press the

1,

@

shutdown and sound 2 short chirps then 1 long

chirp to confirm ready mode is set.

Start

button 2

0

Ready

Cancelling Remote Start Ready Mode

exit remote start ready mode if any

The system

will Open Open

any door the hood

trunk (if connected)

or Press the brake Release the parking brake

Turn the ignition

ON

of

following

the

occur:

2014 Voxx Electronics Corporation.

All

rights reserved.

7

Remote Starting

To

activate the remote vehicle start function, press and release the within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. correct, the vehicle will start within 5 seconds. The vehicle's parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running.

Your Vehicle

0

button 2 times

If all safety parameters are

If your vehicle stalls

2 more times to start the vehicle

5 seconds between each start attempt.

attempt, the system will abort the remote vehicle start process.

Remote Start

Press and hold the

Shutdown

Entering the Vehicle while

1.

2.

3.

4. Press the brake pedal. The remote vehicle starter will disengage and the vehicle will operate normally.

Unlock the vehicle's doors. Enter the vehicle. DO NOT PRESS Insert

position.

or

does not start, the system will pause

(a

total

of

3 attempts). The system will pause

If

the vehicle does

0

button for 3 seconds to turn the vehicle off.

it

is

Running via Remote Vehicle

THE BRAKE PEDAL!

the key into the ignition switch and turn to the

5

not

seconds, then try

start after the 3rd

Start

ON

or

RUN

Preheating

Before exiting the vehicle, set the temperature controls to operation. After the system starts the vehicle, the heater activate and heat

or

Precooling

or

the Vehicle's

cool the vehicle's interior to your setting.

interior

the

desired setting and

or

air

conditioner

will

8

ca6554 Owners revA

User Programmable Run Time I

Run Time Extension

allow

The system has the

running under control

ability

to

the remote start. This will only

of

current run time setting during the current remote start

the user to extend the time the

extend the run time back to the

cycle. If

your system is set to

run 15 minutes and the time remaining is 4 minutes, extending the the countdown timer to 15 minutes and your minutes.

Follow the steps below

The remote start must already be active.

1.

2.

3.

Press and

The system

release

will

confirm that the

Using the

you want to make a short stop and keep your vehicle

If

warm or

"Quick-stop"

cool),

the quick-stop feature

Feature

to extend the vehicle's run time.

button 4 times.

0

the

chirp 1 time and flash the parking lights

time has been reset.

run

allows

vehicle will

you to do this

secure and your keys with you.

continue to

running (to keep the interior

while keeping your vehicle

·

vehicle will

will

time

run

for another 15

run

4 times to

be

reset

To engage

1.

2.

Stop the With your foot off the brake pedal, press and

times within 2 seconds. The LED stop

3.

Remove the keys from the ignition and exit the vehicle.

quick

entered.

is

stop:

vehicle

place the transmission

and

will

PARK.

in

release the 0

button 2

flash 3 times to confirm quick

Press

the@

button to lock the vehicle's doors if desired.

Note:

Do not leave children

or animals unattended

the vehicle

in

when using the

quick-stop feature.

Hour

3

I

Operating the

2

The system has the ability to start the vehicle every 2 This feature is

especially useful

Start Up Timer Mode

cold climates

in

3 hours for a 48 hour period.

or

where the only

means to keep the

engine and engine fluids warm is to periodically start the engine. The default setting

option programming.

is 3 hour,

Selection between 2 or 3 hour is made

in

WARNING!

certain that the vehicle is outdoors before using this or any remote starting

Be device. A running engine produces dangerous carbon monoxide fumes which can be

harmful

or

if prolonged exposure occurs.

fatal

garaged.

Voxx Electronics Corporation. All

2014

rights reserved.

DO NOT

remote start the vehicle if it is

9

To

begin the 2

1.

I

3

hour

start

up

timer

Turn the vehicle's ignition

mode:

ON

then

OFF.

2.

3.

Press and Press the

a.

hold

the

0

button 4 times, the system will;

When set for 3 Hour (default)- chirp 2 times

parking lights 4 times.

b.

When set for 2 lights 2 times.

To

4.

exit

1.

OR

1.

Release the valet button.

the 2

I

3

hour

Turn

the vehicle's

start

up

Ignition

Activate the remote vehicle start feature using the remote

Turbo Timer

This option

will keep the engine running

down before shutting the engine

valet button.

Hour-

timer

mode:

ON.

to

off.

and

flash the

chirp 1 time

and

flash the parking

control.

allow the vehicle's turbo to properly cool

To

engage the Turbo Timer feature:

1.

With the vehicle running via the ignition key

2.

brake Engage the vehicle's parking brake

pedal.

buttons simultaneously.

3.

The vehicle's parking lights will feature has been activated.

4.

Turn the ignition key programmed time has

To

disengage

the

turbo

timer

and

turn

on

OFF,

the vehicle

elapsed

(1,

3,

feature, press the

and

your foot off of the

press the

to

verify the Turbo Timer

will

continue to

~

run

or 5 minutes)

vehicle's

brake

and 0

until

pedal.

the pre-

10

ca6554

Owners

revA

Operating the Daily Start Timer

The system has the

ability

to start your

vehicle

based

on

a 24-hour countdown timer.

This feature requires a two-part activation sequence. From the remote, of

the vehicle, countdown timer (the finished operating the

pressing both the

vehicle will

vehicle

for the day, perform the

@

&

0

buttons together

will activate the 24 hour

start 24 hours from this time). Next, When you are

following

steps to

process.

1.

2.

Turn the ignition Within

10

seconds, while pressing the brake, press and

ON/OFF (vehicle

must be disarmed).

release

button twice.

3.

Temperature Start Mode

The system has the ability to start the

temperature

based on the temperature setting and

The

vehicle will emit 2 chirps and flash the parking

threshold.

vehicle

Once activated, the system

will

if the temperature drops

will only start the

be

cancelled

if the

lights

vehicle

vehicle is started with the

key or remote started by the transmitter. Temperature is read from the

below

the dashboard

in

most instances, and the

vehicle's

interior temperature may

vary from the ambient temperature.

while

in

range

complete

the

0

4 times.

below

a preset

one time

module, located

1.

The

vehicle

2.

3.

Press and

The

vehicle will

Note: This feature is

Remote Start Safety Features

must be armed.

release

both the

emit 1 chirp and flash the parking

defaulted OFF

~

&

and must be set

For safety and security reasons, the system will

vehicle

starter from activating if any

1.

The

2.

vehicle

The brake

hood is open.

pedal

is pressed prior to turning the ignition key to the

of

the following

position.

3.

The engine is over-rewed (tach checking

4.

Valet

mode is active.

0

buttons together.

lights

in

option programming.

1 time.

shutdown or prevent the remote

occur:

ON

only).

2014

Voxx

Electronics

Corporation.

All

rights reserved.

11

LED Display Indications

LED Function

OFF DISARMED

SLOW FLASH FAST ON 2

3

4

5

FLASH PASSIVE ARMING

(SOLID) VALET

PAUSE

FLASH FLASH

...

PAUSE

...

PAUSE

...

PAUSE

...

Siren/Horn Indications

Chffps Function

1 2 3 4

ARMED

MODE

TRIGGER, HOOD/TRUNK

ZONE ZONE 3

ZONE ZONE 5

2

TRIGGER, DOOR

4 TRIGGER, SHOCK

TRIGGER, IGNITION

DISARM ARM DOOR AJAR UPON ARMING

TRIGGERED

DISARM

I

5

Parking

Flashes

1 DISARM 2 3 DISARM 5 ON

CARLOCATOR

Light

Flash Indications

Function

ARM

TRIGGERED

I

CARLOCATOR

(SOLID) REMOTE STARTED

12

ca6554

Owners

revA

Additional

Check Vehicle Status

2-Way

LCD.

Remote

Control Functions

Press and release

display

Display

Press and

Melody

To

response from the

seconds.

Button

To seconds.

the current status

Illumination

hold

the

I

Vibration Mode

have the remote

Beeps

toggle

button beeps on or off press and

rF

2 times then press

of

the vehicle.

rF

button for 1 second. The display will illuminate

control vibrate, play a melody

vehicle

press and release

@

within 3 seconds, the transmitter

tone or both each time it receives a

rF

then press and

release

[F

then press and

hold

for 5

~

for 2

hold 0

will

seconds.

for 2

Battery

While

incoming

display SAVE

press and

In

Clear Flashing Icons

Press the

flashing icons on the

~.~~

Stopping

•

To

stop the disarming the system, press any button one time the vehicle

Save Mode

in

POWER SAVE MODE the 2-way

signals from the main unit

to indicate that power save mode is

hold

[F

for 5 seconds.

and

Melody

[F

button 3 times within 3 seconds. This

LCD screen .

LCD Trigger Melody

alarm

at this time and the

trigger

melody

alarm will

if

the system has been triggered

until a button

Sound

continue to sound.

LCD

transmitter

is

pressed. The

ON.

To

will clear

only,

this

will NOT look

LCD screen

enter power save mode

the melody

WITHOUT

will

not send a command to

for any

will

sound and

2014 Voxx Electronics

Corporation.

All

rights reserved.

13

Button

Press and release on or off. When the button

Lock

then press

[F

for 2 seconds to toggle the button lock

hold the

is active, the remote control will

lock

@

when a button is pressed indicating it is locked.

Illumination

2 times then press and

Press and release illumination

on

[F

or off. When on, the display

will illuminate

command.

Mode

Car

2

hold

beep/vibrate 2 times

for 2 seconds to toggle

@

when it receives or sends a

then press

control a second security system enter 2 car mode by pressing

To

icon appears on the transmitter's LCD

together for 3 seconds. When the

riJ

and

control the second security system. Use the same method to exit 2 car

screen it mode and resume control

will

the original vehicle's security system.

of

NOTE: A second security system must be installed learned

it before this feature

to

will operate the additional system.

W

and the

LCD

[F

transmitter must be

Parking Meter Countdown

The parking meter countdown timer has 6 preset times, to access the preset times

for 2 seconds,

then press and

and begin countdown press and release

will increase the countdown time.

~>))

each additional press

Clock

Adjusting

The clock,

the

alarm clock and programmable countdown timer are accessed through the

Function Menu. Press and

of

Timer Settings

and

hold

for 3 seconds

[F

access the function menu, once

to

you have accessed the feature menu press and release feature and

follow

the steps below

to adjust the settings for each. Press and

[?

hold

to

~>))

scroll

through each

hold

for 2 seconds to exit the menu.

@

[F

Clock Clock

Hour Press

Minute Press Alarm Clock Hour Press Alarm Clock Alarm Clock

Minute Press ON

Countdown Timer Hour Press

Countdown Timer Minute Press Countdown Timer ON

14

OFF

I

OFF

I

Press

increase or

to

~>))

to increase or

~>))

to increase or

~>))

increase or 0 to decrease

to

~>))

to turn

~>))

increase or

to

~>))

to increase or

~>))

turn

to

~>))

ON

to decrease

0

0 to decrease

to decrease

0

to turn

0

or

to decrease

0 0 to decrease

to turn

0

or

OFF

ca6554 Owners revA

LOCK

~

UNLOCK

~

~[Rllri]

~«)1~)

SYSTEM ARMED

TRANSMITTING

TRUNK

TRIGGER

~

HOOD TRIGGER

~«n~

¢ooo:

~~

SYSTEM TRIGGER

BATIERY

VIBRATE/SILENT MODE

INDICATOR

~~

~

ff1

3(

X

~~v~

t

VALET

IGNITION ON/TRIGGER

DOOR TRIGGER

FULL

TIME COUNT DOWN

BATTERY SAVE MODE

MELODY MODE

MODE

SHOCK TRIGGER

ill]

~

RB

3

g:e

RS

CAR MODE

2

ALARM CLOCK

TEMP.

TIMER START MODES

AUX 1 OUTPUT

AUX 3 OUTPUT

AUX 5 OUTPUT

I

:ss:ee

f)

RBJ

g:e~

TIME DISPLAY

ENGINE RUNNING

AUX

AUX 2 OUTPUT

AUX4

MODE

OUTPUT

2014

Electronics

Voxx

Corporation.

All

rights reserved.

15

16

ca6554

Owners

revA

Electronics

Voxx

2014

Corporation.

All

rights reserved.

17

1 Way 4

Button

Remote

Control-

Model CAT4

The batteries inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED the remote control will dim.

To

replace the remote control batteries:

on

1.

Using a coin, disassemble the halves

of

the remote

control.

2.

Remove the old battery, observing

the+/-

symbols

on

the

batteries and replace with a new battery.

2 Way

3.

4.

LCD

Reassemble the halves Test operation

Remote

Control-

of

the remote control.

Model CATLCD

of

the remote control

The AAA battery inside the 2-way LCD remote control should last approximately 6

months under normal use. When the battery becomes weak you will notice the remote

control range (the distance from the vehicle the remote control will work) deteriorate and

on

the BATTERY icon

1.

2.

Gently slide the battery cover off

Remove the old AAA battery, observing the +/- symbols

the LCD remote control will show 1 bar or less.

of

the remote control.

on

the

battery, and replace with a new AAA battery.

3.

4.

18

Gently slide the battery cover on to the back

Test operation

of

the remote control.

of

the remote control.

ca6554 Owners

rev

A

Code Systems,

Inc. Limited Lifetime Warranty

Code Systems

security product (the

Inc. ("CODE") warrants to the

"Product"),

purchased from an authorized

ORIGINAL PURCHASER

CODE

dealer, that (except as provided

below) should this Product under normal use and conditions, be proven defective

WHICH IT WAS ORIGINALLY INSlALLED,

manship

DURING

such defect(s)

THE

be repaired or replaced (at CODE's

will

to repairs of the defect( s

LIFETIME OF

).

THE

VEHICLE

IN option) without charge for parts directly

Switches, indicator lights, and transmitter cases are similarly warranted to the original pur-

the Product.

chaser for a period

CODE

one ( 1 ) year from the date

of

separately, are covered by the

accessories,

sold

purchase

of

applicable

warranty accompanying

the accessory.

non-transferable, non-assignable and is voided when: (1) the Product

This warranty removed from the originally installed

This warranty does not

abuse, improper

installation, alteration, or use contrary to its intended function, fire, flood, or other natural

vehicle

is transferred to another party.

is

which it was

in

originally installed;

apply

to any product damaged

or (2) the

which the Product was

vehicle

by

in

accident, physical or

acts.

repaired or replaced under the terms

be

order for the Product

In

defective Product must be returned to an authorized

sales receipt. The date

retail

originally installed must be

was

of

to

CODE

purchase and year, make and

clearly

indicated on the

sales

dealer and accompanied by a copy of the

the vehicle

model

of

receipt.

of this

CODE vehicle

material

in

or

this warranty, the

of

which the Product

in

work-

is

OTHER

This warranty is exclusive and

IMPLIED WARRANTIES, INCLUDING

IMPLIED. ABILITY THIS WRITTEN

ANY

AND FITNESS

WARRANTY.

FORA

PARTICULAR PURPOSE, SHALL BE LIMITED TO

IN

OR INCIDENTAL DAMAGES FOR

CODE MAKES

NO CASE SHALL CODE

BREACH

OF THIS OR

NO

IMPLIED WARRANTY OF

ANY

LIABLE FOR

BE

ANY

IMPLIED, WHATSOEVER.

CODE does not warrant that the Product cannot be compromised CODE'S LIABILITY

PROVIDED PRICE

ABOVE AND, BY THE

PAID

UNDER THIS

IN

ORIGINAL PURCHASER OF

Some states do not allow

so the above limitation may not

have other rights which vary from state to state

also

WARRANTY EVENT

NO

the exclusion or limitation

apply to you. This warranty gives you specific

IS LIMITED TO

SHALL CODE'S LIABILITY EXCEED THE

PRODUCT WITHOUT INSTALLATION

THE

of

WARRANTIES EXPRESSED OR

MERCHANT-

THE DURATION OF

CONSEQUENTIAL

ANY

OTHER

or THE

WARRANTY,

circumvented. THE EXTENT

REPAIR OR REPLACEMENT

EXPRESS OR

OF

PURCHASE

LABOR.

incidental or consequential damages,

may

legal

rights and

you

Electronics Corporation. All

Voxx

2014

rights reserved.

19

Voxx

Electronics

Corporation.

FCC

COMPLIANCE

Customer

Service 1-800-421-3209

WWW.CODE-ALARM.COM

This device Industry

1.

This device may not cause

2.

This device must accept any interference received,

may cause undesired operation.

Warning!

Changes or modifications not compliance could

complies

Canada. Operation is subject to the

with Part 15

void the user's authority to operate the equipment.

PATENTED:

20

of

the

FCC rules

following

harmful interference, and

expressly

www.

voxxintl.com/company/patents

approved by the party responsible

R410-192-720

and with

two conditions:

including

RSS-21 0

of

any interference that

for

ca6554 Owners revA

WARNING

THIS VEHICLE IS EQUIPPED WITH

A

REMOTE

CONTROLLED CAR STARTER

BEFORE

SERVICING THIS VEHICLE, REMOVE THE MAIN

POWER FUSE (RED

WIRE) TO THE

CAR

STARTER

OR

DISCONNECT

THE

VEHICLE BATTERY.

LBL0675

Register

online

at:

.CODE-ALARM.COM

Click

On

Product

Registration

and

Fill

Out

the

Brief

Questionnaire

·

PRODUCT

REGISTRATION

Thank

you

for purchasing a Code-Alarm product.

We

pride

ourselves

on

the

quality

and

reliability

of

all

our electronic products,

but

if

you

ever

need

service or have a question, our customer service staff stands

ready

to

help.

Contact

us

at www.Code-Aiarm

..

com

PRODUCT PROTECTION:

In

case of

an

insurance

toss

such as fire, flood or theft, your

registration will serve as proof of purchase.

PURCHASE REGISTRATION:

Registering On-Line will allow

us

to contact

you

in

the unlikely

event a safety notification

is

required under the Federal Con-

sumer Safety

Act.

1026350

MAXIMUM INSURANCE DISCOUNT AUTHORIZATION

Dear

Insurance

Agent,

The installation of my Code-Alarm automatic (passive) arming security system

in

the vehicle indicated below qualifies me for the maximum discount

mandated by

law

in

some states and by insurance company option

in

other~.

This

vehicle security system automatically arms itself

after the doors are

closed and includes at least one engine disabling relay to prevent the engine from being started.

Insured

Signature:

_______________________

Name(pleaseprint

):

______________

_

Street Address:

__________________

State:

__________

Zip:

___________

_

Insurance

Company:,

________________________________________

_

Policy#:-------------------------------------------Vehicle

Year/Make/Model:

_______________________________________

_

Vehicle Identification

#:

---------------------------------------------------

The signature

below

certifies that

my

Code-Alarm

automotive security system

was

installed

on

___________

_ (date)

__

_

Installer

Signature:-------------------------------------------

Company:

____________________

·---~---------------------

Address:

---------------------------------Telephone:

________

_

PLEASE COMPLETE AND

MAIL

TO YOUR INSURANCE COMPANY

1026673

$2,500.00

I M I

L

CODE

SYSTEMS,

Should YOUR

Inc makes the following warranty to

private passenger vehicle

T

E

in

which the

D

CO dealer and while the system is operational and activated be stolen and not recovered or for theft insurance purposes. then subject to the following conditions, deductible on your existing insurance not to exceed

$2,500.00.

This Limited Warranty is effective for thefts occurring within one ( registration form has been completed in full and received by the CODE-ALARM Program with postmark that is within five (5) business days vehicle in which the States

of

America

CODE-ALARM

or

Canada;

(D) the theft

ANTI-THEFT SYSTEM

of

from

YOUR

vehicle occurs within the

w

A

R

YOU as the original purchaser

DE-ALARM

ANTI-THEFT

YOU will be refunded the comprehensive auto insurance

l)

year

from the original date

the original date

has been installed;

of

purchase; (B)

(C) YOUR

United

R A N

of

this sys tem.

SYSTEM

is originally installed

if

stolen and recovered be deemed a total loss

of

purchase providing that: (A) the attached

Administrator at the address shown below

YOU

properly and completely identify the

vehicle is registered within the United

States

of

America or Canada;

complete theft report with the police or other law enforcement agency having jurisdiction at the location

comprehensive vehicle with YOUR

or

theft insurance

insurance carrier; a

in

force on the vehicle at the time

nd

(G) the theft claim with

of

the theft and YOU

YOUR insurance carrier

have filed a claim for the theft

is

settled and final payment

been received.

This Limited Warranty applied solely not apply to any vehicle used

in

a busines

to

passenger vehicles, motor homes, and light duty trucks

s,

for Livery or offered for hire. This Limited Warranty applies only to the vehicle as identified on

or

vans not exceeding

the attached registration form.

In order to make a claim under the Limited Warranty,

YOU are

to

provide the

CODE-ALARM Program

following information and materials:

• Proof

•

of

YOU

ARE

A certified

purcha

se

including the purchase date.

URGED TO SAVE YOUR ORIGINAL RECEIPT

or

notarized complete copy

of

the police report filed by

T

by

of

the theft; (F)

YOU

(E)

13,500 GVW.

Administrator with the

y

an authorized

YOU

file a

YOU

have

of

from them has

the

It does

CONTINUED

THIS

CARD

OF

YOUR

Code

-Alarm

Anti-Theft

Name

City

Vehicle

Year

In

surance

Carrier Polic

Amount

of

Com

D

ea

ler

Name

Price Paid

OPTION

Annual Household Inc

For

AL

INFORMATION

•

A copy

of at the time show the amount

•

A copy

ON

REVERSE

MUST

BE

POSTMARKED

CODE-AlARM

RETAINED

AND

CONSUMER

Sys

tem

Pur

chased

State

Make/Model

rehensive

or

Theft Deductible

S

stem Was

A e

ome

: Less than

the original declaration sheet from the insurance policy in force

of

the system purchase. This declaration sheet must clearly

of

the insurance company settlement check and any

WITHIN

ANTI-THEFT

SUBMITTED

REGISTRATION

S

of

Buver: Purchased for:

$20.000

c:::J

the deductible applicable to theft losses

ADV-

THIRIY

SYSIEM

WITH

Address Zip Phone

YIN

Address

In

sta

$20-40.000

(30)BUSINESS

ORIGINAL

ANY

CLAIMFll.ED

ll

ation Included? Yes

c:::J

PURCHASE

CARD

Pur

chase

Date

c:::J

Yourself

$40-60.000

c:::J

HEREUNDER

re

lated documentation

DAYS

OF

THE

RECEIPT

No

As a Gift

c:::J

More than

PURCHASE

MUST

c:::J

$60.000

c

BE

c:::J

BY

YOUR

SI AND T

HIS

Sig

(2) LIMITED

naiUr

YOU

e

GNATURE

BELOW

UNDERSTAND

WARRAN

TY

IS

. YOU

AND

NOT

AGREE

AN

(I)

AGREE

THAT

INSURANCE

TO

A

CODE

POLICY

LL

OF

THE

SYSTEMS,

.

TERMS

Da

te

Inc

AND

IS

PROVIDIN

CON

DITION

G

YOU

S

SET FORTH IN

WITH

A

LIMIT

ADV-

THIS

ED

WARRANTY

LIMITED

WARRANTY AND

THAT

1026699

c

The

CODE-ALARM Program that may Program

All claim information must be mailed to the of

For the protection mail Alarm office.

be

reasonably required to verify

Administrator's property and will not be returned .

the final settlement check from YOUR

of

or

any other means such that

Program Administrator is

Please

YOUR

allow four (4) to six (6) weeks to process any claim hereunder.

Administrator reserves the right to ask for

rights,

YOU

are urged to make copies

YOUR

not

responsible for materials not received

YOUR

claim. All documentation received

Code-Alarm Program

insurance carrier.

package can be traced in the event

of

an

Administrator within thirty

all materials submitted and to send all materials via registered

y other similar documentation

of

in

on

a claim becomes the

(30)

business days after receipt

its becoming lost

the

CODE-ALARM Program

or

misdirected. The

or

other materials

Code-Alarm

Administrator

Code-

's

This limited warranty is not an insurance policy underlying comprehensive auto insurance coverage and your compliance with all the terms and conditions set forth herein. This limited warranty has no cash value and is subject to all the terms and conditions set forth within this document.

This warranty is

WARRANTY CASE SHALL CODE-ALARM QUENTIAL IMPLIED, WHATSOEVER.

expressed herein in connection with the sale

Some

states do not allow limitations on how long an implied warranty lasts damage so the above limitations also have other rights which vary from state

in

lieu

of

OF MERCHANTABILITY, SHALL BE LIMITED

OR

THIS

all other express warranties

OR

INCIDENTAL

WARRANTY AND WARRANTY

THE

DAMAGES

No person

or

exclusions may not apply to YOU.

MARKETED

or

insurance coverage and is contingent on the existence

or

liabilities.

CODE-ALARM PROGRAM ADMINISTRATOR

FOR

or

to

BREACH

representative is authorized to assume for the

of

this product.

state.

PROGRAM IS NOT

IN

OR FROM

ANY IMPLIED WARRANTIES.

TO

THE

DURATION OF THIS

OF

THIS

OR

ANY

OTHER

or

the exclusion or limitation

This warranty gives YOU

THE STATE

AVAILABLE AND OF

FLORIDA.

of

and payment from an

INCLUDING ANY IMPLIED

WRITTEN WARRANTY, IN

BE LIABLE

WARRANTY,

Comp

specific legal rights and

MAY NOT

FOR ANY CONSE-

any

of

EXPRESSED

any liability

incidental

BE

oth

or

consequential

er than

YOU

NO

OR

may

THE

CODE-ALARM PROGRAM ADMINISTRATOR

Post Office Box

Encinitas,

Phone (800) 708

CA

231809

92023

2113

CODE-ALARMLIMITEDWARRANTYPROGRAM

Post Office

Encinitas,

Box 231809 CA

92023

POST

OFFI

WILL N

DE

LI

VER

WITH

OU

T PROPER

PO

STAGE AFFIXED

HERE

OT

CE