Code Alarm ca6154 Professional Series Installation Manual

CCJCc:~~Ja~m

i=»~OFESSIONAI

SE~IES

Security and Remote Start Installation Guide

for

models:

ca6154

4280602

Table

Before You Begin ......................................................................................... 4

Wire Connection Guide ............................................................................... 5

4 Pin Main Harness ................................................................................... 7

6 Pin Start Harness ................................................................................... 8

6 Pin Output Harness .............................................................................. 1 0

of

Contents

8 Pin Input Harness .................................................................................

4 Pin Alternate Output Harness ............................................................... 14

3 Pin Door Lock Output Harness ............................................................. 15

Additional Ports ......................................................................................... 19

Antenna

DBI Port ................................................................................................... 19

Telematic Interface Port ........................................................................... 19

Set Up

Transmitter Programming ........................................................................ 20

Manual Feature Programming ................................................................. 20

Programming Feature Banks ..................................................................

I LED I Programming Port ........................................................ 19

& Programming ............................................................................. 20

11

21

Tach Programming .................................................................................. 24

Smart Tach less Mode .............................................................................. 24

Adjusting the Shock Sensor .................................................................... 25

Testing the Shock Sensor ........................................................................ 25

Chirp Delete - User Accessible ................................................................ 25

Dome Light Delay

2

I Theater Dimming ..................................................... 25

ca6154 Install revA

Feature Descriptions ................................................................................. 26

Transmitter

Button

Functions ..................................................................

33

Security Trigger Zones .............................................................................. 34

Remote Start Shutdown Diagnostics ...................................................... 34

System

Layout

........................................................................................... 35

Voxx Electronics Corporation.

2014

All

rights reserved.

3

'

BEfoRE

' •

.

::

..

·

YOU

-

.:-_=_

:

·.,

.-

- .

~---

•

:,.:

BEGIN

.

.;

...

~-

FOR AUTOMATIC TRANSMISSION VEHICLES ONLY.

PROFESSIONAL INSTALLATION

STRONGLY

Roll down window to avoid locking during

installation

RECOMMENDED

keys

in

vehicle

Avoid mounting components or routing wires near hot surfaces

Avoid mounting components or routing wires near moving parts

Tape or

loom

wires under hood for protection and

•

. . .

appearance

Use a circuits.

Digital Multi

DO NOT USE

Meter for testing and verifying

A TEST LIGHT, OR "COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle

Technical

.

computers.

Support

or

go

to

{800)

421-3209

http://avxtech1.com

4

ca6154 Install

revA

z

<(

~

z

a:

-.;~"

WHITE/RED WHITE BLACK BROWN

PARKING LIGHT INPUT PARKING LIGHT OUTPUT GROUND SIREN

OUTPUT (

+ )

.....

ct:

<(

.....

C/)

z

a:

co

1-

::>

a..

1-

::>

0

z

a..

co

$

'C

'!

PURPLE RED ORANGE PINK/WHITE RED/WHITE PINK

R-J:

Jl

,

~

'

OufptJJ

·

...

' ' -

_:

______

:

__

_

BROWN/BLACK BLUE/BLACK VIOLET/BLACK RED/WHITE L T GREEN/BLACK

:

---

__

:

_:-

--

-: :-

-.

·

_:-

.'

STARTER BATTERY 12V (

ACCESSORY

IGNITION BATTERY 12V ( IGNITION

l!la

·

t:J1e~

;

'

-·

.

s

..

·-

. . . . .

'.

·-;

. .

:-

.. .

..

HORN START STA TIJS

AUX 1 OUTPUT TRUNK RELEASE OUTPUT FACTORY DISARM

i

OUTPUT-

1

2

(

+)

1

(

+)

OUTPUT

MOTOR SIDE

+)

(

+ )

+)

(

- )

I

ACTIVE OUTPUT

(

- ) (

- )

I

PULSE BEFORE

(

- )

START

(

- )

ORANGE

2014

GROUND

WHEN

ARMED

OUTPUT ( - )

5

I-

=>

c..

z z

c..

co

:

,,_;_;::.:::~>--:

-',·

-_

>::~:(

:

(~=::-

BLUE/WHITE INSTANT TRIGGER INPUT GREEN PURPLE WHITE/BLUE GRAY GRAY/RED

BROWN/RED

n

·

,J

;:.

I

;

lnput

,.

..

~

·

···

arness

H.

DOOR TRIGGER INPUT DOOR TRIGGER INPUT EXTRENAL START INPUT

(

(-)

+ )

HOOD PIN INPUT

PARKING BRAKE

BRAKE

INPUT

((

INPUT

(

)

+ )

( - )

- )

(

- )

z~

-(.)

a

c..

M...J

PURPLE/WHITE

BLACK/YELLOW GREEN/WHITE LT BLUE FACTORY ARM

L T GREEN/BLACK

~oc~

'·.

~

o

.

I

:

P

·['

I

I.l~~.

·

~

--~,

_:_

.

·-

-.

_ .-

_-

-

-.

;:"

·_

.-,__

BLUE UNLOCK OPEN

GREEN

TACH INPUT

PULSE PULSE

FACTORY DISARM

all'ft~s

.

ij

OJ,~put

.:.

-_--=:---=,::·:·-:

~-

.

- .

-·

.\---

LOCK

DURING AFTER SHUTDOWN

-~-

:··-·

-,;.

-

:,_----_:=_.

(-)

:;.

(-)

...

.

CRANK (

PULSE

I

- ) (-)

AFTER

PULSE BEFORE START

START

- )

(

)

(-

6

ca6154

Install

revA

1

WHITE/RED

PARKING LIGHT INPUT

2

WHITE

PARKING LIGHT OUTPUT

Locate the parking light output wire at the vehicle's light switch.

Verification:

This wire registers positive voltage when the parking lights are

turned on.

Positive switching Parking Lights:

Connect the Connect the WHITE

WHITE/RED

wire to the parking light output wire.

wire to a 15 Amp

max

fused battery source.

Negative switching Parking Lights:

Connect the Connect the WHITE

3

BLACK

Connect

the

BLACK

WHITE/RED

wire to a good chassis ground.

wire to the parking light output wire.

GROUND

wire to a solid chassis ground point using a ring terminal and

self tapping screw (not supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended grounding point is a metal surface in the driver's side kick panel area.

NOTE:

4

Locate a suitable mounting location

Do not ground the

BROWN

BLACK

wire with any other vehicle components.

SIREN OUTPUT (

in

the engine compartment for the siren,

+ )

away

from moving parts. With the

tapping screws, being careful not do drill into any hoses, wiring Connect

tapping

bell

of

the

BLACK

screw

the siren aiming downwards, secure the siren in place using

or

components.

siren wire to a chassis ground using a ring terminal and

(not supplied).

self

Route the BROWN siren output wire from the control module through the firewall and connect to

NOTE:

the

RED wire on the siren.

Be sure to loom the siren wires, and seal the grommet.

2014 Voxx

Electronics Corporation.

All

rights reserved.

7

1

n

'.

Pi

..

<6

PURPLE

·Start;

Harness

STARTER

OUTPUT

(

+ )

Locate the

Connect the PURPLE wire to the vehicle vehicle

2 RED BATTERY 12V (

Locate 1

vehicle

Verification:

START

of

the

kill relay.

starter

Verification

KEY SIDE START position. MOTOR SIDE

starter wire when

Verification:

switch.

starter wire. This wire registers

position. Cut the vehicle's

starter wire is cut:

after

starter wire registers

of

starter wire registers no

of

installing

vehicle's

This wire

constant 12

register

will

voltage

the starter kill relay.

Volt battery wires at

only

starter wire

voltage

voltage.

starter wire, use the

(+)voltage

when the

half

in

when the

+)

all

in

is turned to the

key

when

key

the

positions

installing

is turned to the

MOTOR SIDE

ignition switch.

of

the

of

the ignition

Connect the RED wire to the constant 12

NOTE:

3

Locate the

Connect the

Remove

ORANGE ACCESSORY 1 ( + )

vehicle's

Verification:

(Accessory) and the key is turned to the

all fuses

accessory wire at the ignition switch.

This wire registers

ORANGE

until all

ON (or RUN) position. The voltage

START

wire to the vehicle's

connections are made.

voltage

(or CRANK) position.

Volt battery wire.

when the key

accessory wire.

turned to

is

drops out when the

ACC

8

ca61541nstall

revA

4

PINK/WHITE

IGNITION

2

( + )

Locate the

vehicle's

2nd ignition wire at the ignition switch (if equipped).

Verification: This wire registers voltage when the key RUN) position, but not the

drop out when the key is turned to the START (or CRANK) position.

Connect the

Programmable

5

RED/WHITE

Locate 1

PINK/WHITE

output:

of

the vehicle's constant 12

Verification: This wire

switch.

Connect the RED/WHITE

NOTE: Remove

all fuses

ACC

wire to the vehicle's

IGN, ACC,

(Accessory) position. The voltage does not

ignition 2 wire.

Start.

BATTERY 12V (

Volt battery wires at the ignition switch.

will

register ( + ) voltage

wire to the constant 12 Volt

until all

connections are made.

is

turned to the

+)

in

all

positions

battery wire.

ON

of

the ignition

(or

6

PINK

IGNITION

1

( + )

Locate the vehicle's ignition wire at the ignition switch. Verification: This wire registers voltage when the key is turned to the

RUN) position. The

voltage does not drop out when the key

is

turned to the

START (or CRANK) position.

Connect the

This wire is

PINK wire to the vehicle's

also

used for

Ignition

1

Output.

Ignition

wire.

ON

(or

2014

Voxx

Electronics

Corporation.

All

rights reserved.

9

1

BROWN/BLACK

HORN OUTPUT

- )

(

Locate the

Verification:

vehicle's

horn wire.

This wire

ground when the horn switch is pressed.

Connect the output,

2

200mA.

BLUE/BLACK

BROWN/BLACK

This wire provides a ( - ) and remains

used for

multiple

until4

seconds after the remote start is shutdown.

application's a 1 amp diode is required in-line with the stripe facing

the control module.

3

VIOLET/BLACK

will register at positive voltage and register

wire to the vehicle's horn wire. This is a low

ACTIVE OUTPUT

I

200mA

START STATUS

output when the remote start function is activated

If

AUX 1

this wire

current

- )

(

be

will

This wire provides a

( - )

200mA

output capable

driving relays. For

of

Control

optional accessories (i.e. Power Window/Sunroof, etc.).

activate refer to the transmitter button configuration chart. Please refer to the

To selectable options for timing.

4

RED/WHITE

Locate the

Verification:

vehicle's

This wire

TRUNK

RELEASE OUTPUT

trunk release wire at the trunk release switch.

register either positive

will

voltage

( - )

ground when

or

the trunk release is activated.

option programming.

This is a

current 200mA

low

output and in configurable

in

of

10

ca6154

Install

revA

5 L T GREEN/BLACK

FACTORY

DISARM

I

PULSE BEFORE START ( - )

This wire will supply

a

( - )

200mA

pulse both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter from the key

Verification:

position in the driver's

Connect the

6 ORANGE

This wire will This wire is typically modules

This output can

cylinder

inside the drivers door.

This wire registers ground

LIGHT

GREEN/BLACK wire to the factory

have a continuous (

used for

or

additional

sensors.

be configured in option programming.

if

the key is turned to the unlock

door

cylinder.

alarm

GROUND WHEN

- )

SOOmA

output when the system is Armed.

ARMED

controlling the starter interrupt

disarm wire.

relay

alarm

disarm wire

OUTPUT ( - )

as

well

as

window

1

BLUE/WHITE

This wire is a GROUND input for an

Verification:

2

Locate the

GREEN

vehicle's

Verification:

and the interior door is

Connect the GREEN wire to the

NOTE:

application

Certain vehicles

guide.

This wire when connected

dome

This wire

light

or

door

will

register ground (NEG) when the

light

is on. This wire will

closed and the interior light

vehicle's

may

require

INSTANT TRIGGER INPUT

external

DOOR TRIGGER INPUT

sensor

will

or

secondary pin switch.

trigger the security system.

(

pin switch wire.

register positive

is off.

negative

multiple

connections. Refer to

door

input wire(s).

(-

)

- )

door

voltage

vehicle

is opened

when the

2014

Voxx

11

3

PURPLE

DOOR TRIGGER INPUT

Locate the vehicle's dome light or door pin switch wire.

(

+ )

Verification: This wire

register positive voltage

will

(POS)

when the

opened and the interior light is on. This wire will

Volts when the door is closed and the interior light is

register ground or

"0"

off.

Connect the PURPLE wire to the vehicle's positive door input wire(s).

NOTE:

Certain vehicles may require multiple connections. Refer to vehicle

application guide.

4

WHITE/BLUE

This wire

will activate the Remote Start function when a GROUND pulse is applied to

EXTERNALSTARTINPUT(-)

it from an external device.

5

GRAY

HOOD PIN INPUT (

- )

door

is

Install

a Hood Pin Switch and connect to the GRAY wire. This connection is required

for Remote Start.

Verification: This wire when connected will

vehicle's hood is opened.

Connect the GRAY wire to the hood pin.

NOTE:

6

Be sure to loom the wire, and seal the grommet.

GRAY/RED

PARKING

Locate the vehicle's parking brake wire.

register ground when the vehicle's PARKING

Verification: This wire

will

BRAKE is engaged.

NOTE:

The following connection is required for Manual Transmission Mode.

register ground when the

- )

BRAKE

INPUT

(

12

ca6154 Install

revA

7

BROWN/RED

BRAKE

INPUT

( + )

Locate the

vehicle's brake light

wire at the brake pedal mounted switch. This

connection is required for remote start.

Verification: This wire registers positive voltage when the brake pedal

pressed.

Connect the BROWN/RED wire to the vehicle's brake

8

Locate the

1.

2.

3.

PURPLE/WHITE

vehicle's

ignition

coil

Verification: Test using the

Set voltmeter Attach positive Attach negative

to

AC VOLTS.

lead

of

lead

of

a volt meter to a constant 12 volt

a volt

TACH INPUT

or

fuel

injector

following

in

the engine compartment.

procedure:

meter to the wire to be tested.

4. Start the engine.

5.

Have someone press on the gas pedal slightly connected to the correct wire, the

voltage

reading

engine's RPM increases.

is

light

wire.

source.

as you monitor the meter.

will

increase as the

If

Connect the PURPLE/WHITE wire to the negative side

fuel

injector.

of

the

vehicle

ignition

coil

or

2014 Voxx

Electronics

Corporation.

13

··

,x;',>:;~

~

--

_

<

p~

;,:

~

·

\;;~~

··

••·•

ut

Outp

Ait~rllat•

·~;

•

·,:

-,o-

.

ss

-

. •

-

.

HarM

1

L T GREEN/BLACK FACTORY DISARM

PULSE

This wire

will supply

a

200mA pulse both upon disarming the system and when

( - )

the remote start feature is activated. Locate

from the key

cylinder

Verification:

position in the driver's door

This output can be configured

2

LT

BLUE

inside the drivers door.

This wire registers ground if the key is turned to the

cylinder.

option programming.

in

FACTORY PULSE AFTER START ( - )

This wire will supply successful completion

vehicle's

re-lock

the

a ( - ) 200mA pulse both upon arming the system and upon

the remote start activation sequence and is

of

doors upon remote start

I

BEFORE

START (

the factory perimeter

ARM

necessary.

if

I

- )

alarm

typically

disarm wire

unlock

used to

option programming.

This output can be configured

3

This wire will supply is typically used shutdown.

GREEN/WHITE

a

tore-lock

also

can

It

( - )

be used to

in

PULSE AFTER SHUTDOWN ( -

200mA pulse

vehicle's doors if they

the

pulse

after the remote start shuts down. This

door

a

unlock

pin-switch wire to prevent the

accessories from remaining on after remote start shutdown.

option programming.

This output can be configured

4

Locate the

BLACK/YELLOW

vehicle's

Verification:

second starter (crank) wire at the ignition switch. (if equipped)

This wire registers voltage only in the start (crank) position

in

PULSE

DURING

CRANK ( -

the ignition switch.

200mA output and can be configured

This wire

will supply a

( - )

programming.

)

upon remote start

)

option

in

vehicle's

of

14

ca6154

Install

revA

1

BLUE

UNLOCK

(-)

3

The door

GREEN

lock

unlock

I

outputs are designed to control several

systems which may require

door lock system is

chart to see which type types are shown in the

These wires

Negative

Door Lock and Unlock:

All

supply

Switching

of

following

a ( - )

Locks

500mA output.

switch.

Verification: These wires

switches are activated.

(-)

Please

in

review the wire and

vehicle.

your

additional

LOCK

parts.

diagrams.

Locate the lock

unlock

I

wire at the

will register ground when the Lock and

different types

of

location

The most common

unlock

vehicle's lock

I

Unlock

Connect

the GREEN and BLUE wires shown

Negative Locks:

GREEN ( - ) Lock Output

BLUE ( - ) Unlock Output

the diagram

in

Vehicle Door Lock

Control Relays

below.

Electronics

Voxx

2014

Corporation. All

rights reserved.

15

Positive

All

Door Lock and

Switching

switch.

Locks

Unlock:

Locate the lock

I

unlock

wire at the

vehicle's lock

I

unlock

Verification:

Unlock

These wires will

register

switches are activated.

positive voltage

Connect the GREEN and BLUE wires shown

Positive Locks:

Vehicle Door Lock

Control Relays

Reverse

Polarity

Locks

{5-Wire

Door

locks)

in

the diagram

when the Lock and

below.

GREEN ( - ) Lock

BLUE (

- ) Unlock

Output

All

Door Lock and

Unlock:

Locate the lock

I

unlock

wire at the

vehicle's lock

I

switch.

Verification:

voltage

These wires

will

when the Lock and

rest at ground and register positive

Unlock

switches are activated.

Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram using (2)

SPOT relays (not supplied).

Reverse

Polarity

Locks:

unlock

below

16

Cut

ca6154 Install

revA

Negative Multiplexed

Door Lock and

All

Unlock:

switch.

Verification:

This wire Please consult your vehicle.

Locks

Locate the

show variable ground when the switch is activated.

will

lock

unlock

I

wire at the vehicle's lock

the wire and location chart for specific resistor values

unlock

I

for

Connect the GREEN and BLUE or BLUE/GREEN wires shown using (2) SPOT

relays (not supplied).

Multiplex Locks:

Positive Multiplexed Locks

unlock wire at the vehicle's

I

All Door Lock and Unlock: switch.

Locate the

lock

the diagram

in

Unlock

)

BLUE ( •

lock

Output

I

below

unlock

Verification:

activated. values

for your vehicle.

This wire will

Please consult

show variable positive

the wire and

location

Connect the GREEN and BLUE or BLUE/GREEN wires shown using (2) SPOT

2014 Voxx

Electronics Corporation.

Multiplex

relays (not supplied).

Locks:

-----~~~------

rights reserved.

All

voltage

when the switch is

chart for specific resistor

the diagram

in

Output

) Unlock

·

BLUE (

Lock

Door

Vehide

Control Relays

below

17

Adding Aftermarket Actuators

After

installing

wires shown

aftermarket actuators, (not supplied). Connect the GREEN and BLUE

in

the diagram

below

----~---t

using (2)

---t-----1

SPOT relays (not

Fused +12 Battery

Fused +12 Volt Battery

Vdt

Source

BLUE (

supplied).

- ) Unlock

Output

18

ca6154

Install

revA

Antenna

I

LED

I

Programming

Port

Mount the

will

not

near the rear view mirror. metallic cable

Data

Bus

supplied

block

the driver's vision. A good location

window film,

to the

control module and

Interface

antenna/receiver to a

Be

careful

as this will

not to mount the antenna/receiver on any

effect system range. Route the antenna/receiver

plug into the antenna port.

Port

clear

spot

on

is usually

the

vehicle's windshield high

on

the windshield

This 4 pin port is used for Flashlogic Door Lock and Transponder Databus

to communicate with the

Flashlogic be

available. Please

Door Lock and Transponder

vehicle's Databus. When using the

Interface modules the

refer to the D2D (Data to Data) function

DBI

port to

following

options may

list available

control

on the tech service web site.

Tach Door Trigger

Input

Brake Safety Shut Down

Trunk/Hatch Open

that

Interfaces

the

per

vehicle

Door Lock

Control Dome Light Supervision Transponder Interface Factory Manual

Alarm

Arm

I

Arm

Disarm

Telematic Interface Port

This 4 pin port is used for

Pro, which can

Door Lock Sliding Car

control

some of the

Control

Doors AUX Output

Find Remote Start

Passlock

I

Disarm

Inputs

Diesel Glow Plug Input

(factory keyless controls

telematic Interface

following

Trunk

I

Passkey

Interface

(GM

Only)

Activation

system)

accessories, such as Car Connection

features.

Release

2014 Voxx Electronics Corporation.

All

rights reserved. 19

1.

Turn the ignition ON.

2.

3.

4.

5.

6.

NOTE: NOTE:

system.

NOTE:

transmitter

NOTE:

ignition is turned

system.

Press and Within

Press 1 button

The system

Pressing the override button at anytime during programming

the next bank.

The system will This system has 1 button programming which programs all channels

The system will hold up to 4 transmitters

This system has PTN - Programmed Transmitter Notification. Each time the

10

will

valeUoverride

the

hold

seconds the system will

each transmitter you wish to program.

of

respond with 1 chirp for each accepted transmitter.

will

exit transmitter programming after 15 seconds

erase the oldest transmitter

the LED will

ON,

flash the number

button.

chirp (3) three times.

memory.

in

will advance to

inactivity.

of

memory, programming a 5th

in

transmitters programmed to the

of

the

Manual

1.

2.

3.

4.

5.

6.

Turn the ignition ON.

Press and

Within

Use the feature programming advance to Feature Bank four, (5) five, (6) six and (7) seven chirps.

Use the transmitter feature bank, the system

Press the transmitter flash indicating the changed feature.

Feature Programming - Feature Bank 2

valeUoverride

the

hold

seconds the system

10

valeUoverride

button to advance through each option bank. For

0

i

button to scroll

will

button to change the desired feature. The LED

button.

chirp (3) three times.

will

2,

through the

chirp to match the feature number.

- 5

4 or

3,

selections

which is (4)

5,

each

in

will

20

ca6154

Install

revA

Defaulting All

banks

will

default

Features:

all

Pressing the

features

and

a

button anytime

while

return you to feature bank

in

any

2-

of

the feature

4 chirps.

NOTE:

is on, there is no time

Feature Bank 1 Transmitter Programming

The system

3 Chirps

will

remain

limit.

in

To

exit programming turn the

Refer to transmitter programming.

feature programming mode as

IGNITION

long

as the ignition

OFF.

I

Parking

Light

Pattern

2014

Voxx Electronics Corporation.

All

1

-Disarm

rights reserved.

2-

Disarm

21

22

ca6154

Install

revA

4 Black I Yellow Output

Running

23

Tach Programming

The

unit

will

not

operate

turned ON.

programming tach, the unit will been learned vehicle, re-engage the starter motor.

If

an attempt is made to start the vehicle

and stored.

the unit may not

unless

If

the tach rate is not

realize

tach

flash the parking

that the

is

programmed

vehicle

or

tach less

via the remote start without first

lights 7 times indicating tach has not

properly

is running

programmed to the specific

in

certain instances and

option

is

The Remote Start

packs, or

NOTE:

poor tach source, the parking connect the PURPLE/WHITE learn

single

1.

2.

3.

4.

5.

6.

7.

routine.

Turn the ignition key to the ON Press and Immediately turn the ignition key Press and

the When the unit senses the tach

flash. Allow

Release turn on for 2 seconds and 1 tach

If the unit

unit

injector.

key.

the

signal

fails

will learn

To

release

hold

the

vehicle to

valeUprogram

is stored and the unit has exited tach

to

learn

the tach rate

learn

tach:

the

valeUoverride

settle to a

push-button switch. The parking

long

tach rate due to

lights will

wire to the proper tach

not flash.

of

most

position.

OFF.

button, then start the

signal,

normal idle speed.

chip will indicate that the learned

an

vehicle's single coil, multiple coil

button 3 times.

vehicle

the parking lights will begin to

learn

improper tach connection or a

To

correct this situation,

signal,

and then repeat the tach

mode.

using

lights will

locate

and

Smart Tach

Smart system and when activated programming to

24 ca6154

Tach

1.

2.

3.

less

Activate the remote start. The parking lights should times indicating no tach

Within the 7 flash time period, press and

The system

mode.

Mode

Mode is available only

Tach

less without the need to enter the feature programming mode.

if

a tach

will automatically

signal

will

chirp 1 time indicating the system

signal has never been learned

change the

has been

learned.

hold

Tach

the

Mode feature

begin flashing 7

0

button.

is

now

in

tachless

to the

in

option

Install

revA

Adjusting the Shock Sensor

1.

2.

Increase Decrease sensitivity by turning the adjustment

Testing the

sensitivity by turning the adjustment

Shock Sensor

dial clockwise.

counter clockwise.

dial

Arm the system and wait 6 seconds for the zone to stabilize, then firmly vehicles bumper.

Chirp Delete

System

ARM/DISARM chirps can be toggled

- User Accessible

ON

or

OFF

without entering the

programming feature banks.

OFF.

then

1.

2.

Turn the ignition Press and release

respond with 1 chirp for

will

ON

the valet/programming button 3 times. The system

OFF.

or 2 chirps

ON

for

strike

the

Theater Dimming

Dome Light Delay

I

The system can be programed to delay

second max) for

(60

vehicles

Once programed the system

with a dome light delay

will 'learn' the timing

seconds before arming.

1.

2.

3.

4.

Close all Using the transmitter press

UNLOCK, LOCK. entered

Immediately OPEN system. The system dome the

The LED

doors with ignition off.

The LED

DOME

DELAY LEARN

CLOSE

then

then monitor the

will

light turns off, the system

learning

mode.

will begin to flash indicating the system has exited the

learning mode and is now armed.

button is pressed

arming after the

of

lock

theater dimming feature.

or

the dome

light delay

and

add

LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,

will light solid

to indicate the system

has

MODE.

the door

then add 2 seconds and then exit

will

WITHOUT disarming

door

trigger wire.

Once

the

2

Electronics Corporation.

Voxx

2014

All

rights reserved.

25

Feature Bank 2 - Security

1 -

Silent Choice:

ON

-

Silent

unlock a second time system lock/unlock

OFF

-

normal

Controls

the

arming/disarming upon first press

will activate the arm/disarm chirps respectively. The

will only

sound the arm/disarm chirps upon a second press

buttons.

arm/disarm chirps upon the first press

normal

arm/disarm chirps

of

lock/unlock,

of

the security system.

pressing

of

lock/unlock.

lock/

the

2 - Passive

Active - Requires use Passive -

is

Locks:

closed.

Determines manual or automatic locking

of

the transmitter to

Automatically locks

the

vehicle's

lock

doors 1 minute after the

the vehicle's doors.

of

the vehicle's doors.

Note: For Passive Locks, feature #3 Passive Arming must

set to passive

3 - Passive

Active - Requires use Passive -

Arming:

Automatically

Determines manual

of

the transmitter to arm the security system.

arms the security system 1 minute after the last

or automatic

locking

of

is closed.

4-

Siren

I

Horn:

This feature

selects which output(s) will

sound the system's

arm/disarm chirps. This feature does not effect the triggered state system and during a triggered

cycle, both the siren and horn outputs

respectively.

last

also

the

vehicle's doors.

of

the security

will activate

door

be

door

5-

Siren Duration:

This feature controls

when triggered.

6 - Security:

ON OFF

Controls

-

Full security functionality.

security functionality - ON

- The security system does not trigger. Panic, Remote

other convenience features operate as

7- Anti-Hijack Mode:

Controls car jack OFF - Standard security system operation. ON

- Enables

Car

manual.

26

the length

I

OFF.

of

time the system will

normal.

mode-

ON

I

OFF.

Jack mode functionality as described

Start and

in

the owners

sound

all

ca61541nstall

revA

Orange Output:

Ground

8 -

This wire

Port

OBI

9-

While Armed

either supply a

will

Protocol:

I

(-)output

Determines the protocol type

interface with external modules.

Protocol

OBI

Controls

when armed

the output

of

OR disarmed.

which the

in

OBI

the orange wire.

port uses to

·

ADS

-Arm/Disarm

10

Protocol

Chirp

I Parking

Light

Pattern:

Determines the number

and parking light flashes when the system is armed/disarmed.

Standard - 2 chirps/light flashes with arm, 1 chirp/light flash with disarm. Inverted-

Feature Bank 3 -

1 - Extended

1 chirp/light flash with arm, 2 chirps/light flashes with disarm.

Control

Controls

the timing

the BLUE and GREEN lock output

of

Lock

Output

Pulse:

wires.

Second-

1

Single

3.5 Seconds - Single 1 Second Lock, Double Pulse Unlock - Single

1 second lock pulse, single 1 second unlock pulse.

3.5 second lock pulse, single 3.5 second unlock pulse. 1 second lock pulse,

second unlock pulse.

chirps

of

double

1

Second Lock, Double Pulse

30

Unlock-

Single

30 second

lock pulse, double

1 second unlock pulse. Double Pulse Lock, 1 Second Unlock - Double 1 second

lock pulse,

second unlock pulse.

Factory

2 -

Disarm:

Controls

the timing

of

GREEN/BLACK factory disarm

LT.

the wire on the 6 pin output harness only and does not change the output disarm wire on the 4 pin alternate output harness.

Factory

Disarm-

Single

2nd Unlock - Same output as

Start

Factory Disarm continuous (

Factory

Disarm-

I

- ) output during the remote start cycle. Single 350mS second pulse with unlock and remote start

1 second pulse with unlock and remote start activation.

unlock.

of

Status-

unlock

Single

with 2nd press

1 second pulse with unlock and

activation.

Factory

Disarm-

Single 500mS

second pulse with unlock and remote start

activation.

single

the factory

of

1

Voxx Electronics

2014

Corporation.

All

rights reserved.

27

3

-Ignition

or

OFF.

Controlled

Locks:

Control

of

door locks when the ignition is cycled

ON

OFFLock and

Door locks not activated by ignition.

Unlock-

ignition is turned off. Lock

Only-

Doors lock when ignition is turned on.

Unlock Only - Doors unlock when ignition is turned off.

4

-Trunk

Output

Timing - Red/White Output: Controls the output timing/type

RED/WHITE output.

1 Second Pulse - 1 second pulse output. 1 0 Second - Continuous output for 1 0 seconds.

20 Seconds - Continuous output for 20 seconds.

Latched until IGN ON - Continuous output until the vehicle's ignition is turned ON.

Latched ON until Button is pressed again.

Doors lock when ignition is turned on and unlock when

Press-

Continuous output until the activation button

of

the

5 - Horn

Output

Timing: Control the minimum horn pulse time

in

milli seconds,

some vehicle will require a longer pulse to activate the factory horn.

16mS 1

6-

Real Panic: Controls the horn output when the system is triggered.

ON

- Randomized horn honks when panic

OFF-

Standard pattern horn honks when panic is triggered.

OmS

30mS 40mS 50mS

is

triggered.

7 - AUX 1: Controls the VIOLET/BLACK AUX 1 output activation type and timing.

1 Second Pulse - Single 1 second pulse. Latched- Output stays active until button is pressed again. Latched until IGN ON - Output stays active until the ignition is turned

on.

Dome Light Output - Output used for illuminated entry and is not controlled by the

AUX

1 function

of

the transmitter. Defrost Output Single Pulse - Single 1 second pulse after start Defrost Output Latched 5 Minutes - 5 minute continuous output after

remote start.

28

ca6154 Install revA

Feature Bank 4 - Remote Start Control

1 -

RF

Start Chirp: Turns remote start activation confirmation chirps

ON

or

OFF.

2 - Run Time: Controls the time control down at any time by use

3 -

of

the remote start until the system times out. The system may also be shut

of

Running Lights: Controls the WHITE parking light output wire during remote

in

minutes that the vehicle will stay running under

the transmitter

or

system shutdowns.

start.

Steady-

Parking lights constant during the remote start cycle.

Flashing - Parking lights flash at a slow pace during the remote start cycle.

4

-Tach

Mode: Determines how the system monitors the engine running during

remote start.

Tach - Hard wired directly to the tach wire

of

the vehicle to monitor AC

voltage. Tach less (Crank AverageNoltage) - Determines crank time by averaging the

last 8 times the vehicle was started with the key and then monitors the change

Hybrid (Crank Average the last 8 times the vehicle was started with the

in

voltage after remote start.

I No Voltage) - Determines crank time by averaging

key.

DBI Port - Monitors the vehicle's tach rate through an interface module connected to the DBI port.

5-

Voltage Level: The voltage variance for remote start when set to tachless. (see

tach mode)

HIGH-

The variance

in

battery voltage from before the remote start

is activated to after the engine is running must be greater than 0.5 volts.

in

LOW - The variance

battery voltage from before the remote start

is activated to after the engine is running may be less than 0.5 volts.

6 - Crank Time: Preset output times

7 - Crank Average I Crank Time: The length

for

the PURPLE starter wire.

of

time

in

which the remote start will

crank the vehicle's starter.

Crank Average - Determines crank time by averaging the last 8 times the vehicle was started with the key.

Preset Time - Preset starter output time. (see crank time)

29

8 - Gas I Diesel: Selects engine type and delay time for the starter output wire during

remote start activation.

Gas - Gasoline engine, no delay for the starter output wire.

1 0 Second Delay - Diesel engine, delays the starter output wire for 1 0

seconds after the ignition has been powered up by the remote start.

15 Second Delay - Diesel engine, delays the starter output wire for 15

seconds after the ignition has been powered up by the remote start. 20 Second Delay - Diesel engine, delays the starter output wire for 20

seconds after the ignition has been powered up by the remote start.

45 Second Delay - Diesel engine, delays the starter output wire for 45

seconds after the ignition has been powered up by the remote start.

9-

Single I Double Pulse Start: Switches the remote start activation between a

single or double press from the transmitter.

10

- Ignition 2

Output

Pnik/White: Programmable high current output.

Ignition 2 - Output becomes active with the same timing as the ignition

output and does not drop out during crank. Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank.

I Crank - Output becomes active with the same timing as the starter

Start

output wire, during crank only.

11

-2

or 3 Hour

programmed time and shut down every 2 or 3 hours.

12-

Turbo Timer: When activated, the vehicle will run for the programmed time.

OFF 1 Minute 3 Minutes 5 Minutes

13

- Transmission Mode: Select the type

vehicle's transmission type.

Automatic - For use with automatic transmission vehicles. Standard remote start operation.

Start: When activated, the remote start will activate and run for the

of

remote start activation based on the

Manual - For use with manual transmission vehicles. Remote start ready mode must be set upon exit

14-

Temperature Start: Not available on this model.

30

of

vehicle to enable remote start.

ca6154 Install revA

15 -

Accessory

Output: Programmable high current output.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Ignition- Output becomes active with the same timing as the ignition output

and does not drop out during crank. Start

I Crank - Output becomes active with the same timing as the starter

output wire, during crank only.

16-

Pulse

Additional

Outputs

w/

Unlock:

When the Unlock button is pressed on the remote transmitter the system will also simultaneously pulse additional outputs. Ignition, Accessory

& Ground While Running outputs for 1 second. The 3rd

setting also activates the pulse after shutdown output to turn off the RAP on certain vehicles.

OFFIGN, ACCY,

simultaneously pulse the Ignition, Accessory

When Unlock is pressed no additional outputs are activated.

GWR-

When the Unlock button is pressed the system will also

& Ground while Running outputs

for 1 second. IGN, ACCY, GWR, then Pulse After Shutdown

-When

pressed the system will also simultaneously pulse the Ignition, Accessory

the Unlock button is

&

Ground while Running outputs for 1 second then waits 2 seconds then pulses the green/white pulse after shutdown wire for 1 second.

17-

Door

Lock

Control During Remote Start: Controls the systems door lock outputs

during the remote start sequence.

OFF

-The

system will not lock

Unlock before Start, Lock After Start - Unlock Pulse before remote start sequence begins, Lock pulse after remote start sequence is complete and engine is running.

Unlock Before Start - Unlock Pulse before remote start sequence begins.

Lock After Start - Lock pulse after remote start sequence is complete and

engine is running.

Lock After Shutdown - Lock pulse after remote start shutdown sequence is

complete.

or

unlock the vehicle.

31

Feature Bank 5 - 4 Pin Alternate

Output

Control

1 - Lt Green/Black Output:

and timing.

Pulse

activated.

Ground sequence

Ignition

before Start

Also

I

During

a 1 second

While Running - Continuous output for the entire remote start

until

after the

-

Output

becomes active with the same timing as the ignition output

and does not drop out during crank. Accessory - Output

becomes active with the same timing as the accessory

output, drops out during crank.

Pulse

During Crank -

starter output wire, during

2 - Lt

Blue

Output: Controls

Pulse After Start

I

During Lock - 1 second pulse after the remote start

sequence and has confirmed the vehicle

when lock

is pressed.

Controls the L

Unlock

pulse

T GREEN/BLACK output activation type

-

1 second

when

vehicle shuts down.

Output

becomes active with the same

crank only.

the

LT

BLUE output activation type and timing.

pulse

unlock

is pressed.

is running.

when remote start is

timing as the

Also

a

1 second

pulse

Ground

sequence

While

until after the

Ignition- Output

and does not drop out during crank. Accessory -

output, drops out during crank. Pulse

During Crank -

starter output wire, during crank

3-

Green/White Output:

timing.

Pulse After Shutdown - 2 second

shutdown. Ground

sequence Ignition

While

until

- Output becomes active with the same timing as the ignition output

and does not drop out during crank.

Running - Continuous output for the entire remote start

vehicle

shuts down.

becomes active with the same timing as the ignition output

Output

becomes active with the same timing as the accessory

Output

becomes active with the same timing as the

only.

Controls

the GREEN/WHITE output activation type and

pulse

after the remote start has

Running - Continuous output for the entire remote start

after the

vehicle

shuts down.

Accessory -

Output

output, drops out during crank.

Pulse

During Crank -

starter output wire, during crank

32

becomes active with the same

Output

becomes active with the same timing as the

only.

timing as the accessory

ca6154

Install

revA

4 -

Black/Yellow Output

timing.

Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.

Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.

: Controls the BLACK/YELLOW output activation type and

Ignition

- Output becomes active with the same timing as the ignition output

and does not drop out during crank. Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank.

2014

Voxx

Electronics

Corporation.

All

rights reserved.

33

Security Trigger Zones

the security system has been triggered the LED

If indicating the zone.

FLASHES TRIGGER ZONE

LED

Trunk Input

Flashes

2

Flashes

3

Flashes Shock Sensor

4

Flashes Ignition Input

5

Remote Start

the remote start shuts down

If patterns

below

Shutdown Diagnostics

indicating the shutdown input.

Hood Door

fails to start, the parking

or

I

Input

flash one

will

lights

the patterns

of

flash one

will

below

the

of

manually

To press and

LED 3 Flashes

Flashes

4

5 Flashes

Flashes

7

enter diagnostics and view the

release

FLASHES

the

SHUTDOWN ZONE

button.

._.

Hood Input Brake Neutral Safety Input

Remote

Manual

transmission

Tach not

shutdown, turn the ignition ON

last

Input

Start Valet

Mode

Transmission Mode not set

models only)

Crank Average not

learned

I

and

(manual

learned

34

ca6154

Install

revA

#4120290

BLUE/WHITE GREEN PURPLE WHITE/BLUE GRAY GRARIRED BROWN/RED PURPLE/WHITE

SHOCK SENSOR PORT

TELEMATIC PORT

INSTANT TRIGGER INPUT DOOR

TRIGGER INPUT

DOOR

TRIGGER INPUT ( EXTERNALSTARTINPUT(-) HOOD

INPUT PARKING BRAKE TACH

BRAKE

INPUT

(

- )

(

INPUT

+ )

(

- )

+ )

(

- )

(

- )

10

N

E~

11'1

:5

n:~

m

t

~r_,

~

IU

c

D

u

#4120291

14120110

*4120145

I

••

,0102

ANTENNA LED VALET

PURPLE RED ORANGE

~

PINK/WHITE RED/WHITE PINK

WHITE/RED

0

WHITE BLACK BROWN

BLACK/YELLOW GREEN/WHITE LTBLUE

D

LT

GREEN/BLACK

BROWN/BLACK BLUE/BLACK VIOLET/BLACK RED/WHITE LT

GREEN/BLACK

ORANGE

(o

"'i"

STARTER BATTERY 12V ( ACCESSORY IGNITION BATTERY 12V ( IGNITION

PARKING LIGHT INPUT PARKING LIGHT OUTPUT GROUND SIREN OUTPUT

PULSE PULSE

FACTORY ARM FACTORY DISARM

HORN START STATUS AUX TRUNK FACTORY DISARM GROUND

OUTPUT-

2

(

1

(

DURING

AFTER

OUTPUT

1

OUTPUT

RELEASE

WHEN ARMED

MOTOR SIDE

+ )

1

(

+ )

+)

(

+ )

CRANK (

SHUTDOWN

I

PULSE

I

PULSE

( - )

I

ACTIVE OUTPUT

(

- ) OUTPUT

I

PULSE

)

(

+ )

- ) ( - )

AFTER START (

BEFORE

(

-

)

(

- )

BEFORE

(-)

- )

START

( - )

ss

SHOCK

RED BLACK BLUE GREEN

UNLOCK(-)

LOCK(-)

SENSOR

14700023

BATIERY GROUND FULL TRIGGER WARN AWAY

&

HARNESS

12V (

+)

WHEN ARMED (

(

- )

TRIGGER

- )

( - )

BLUE

#1032714

STARTER

85

I

ORANGE RED

BLACK WHITE OPEN

87

I

87a

I

3o

I

BLACK

INTERUPT

#1024405

RELAY

86

-ARMED

85

-

IGNITION

87A-

STARTER

30

- STARTER

87-

OPEN

&

HARNESS

OUTPUT

( + )

OUTPUT-

INPUT

( - )

MOTOR SIDE

- KEY

SIDE

OPEN GREEN

OBI

PORT

rn

2014

Voxx Electronics Corporation.

All

rights reserved.

35

Voxx Electronics Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

FCC

COMPLIANCE

This device complies with Part 15

Industry Canada. Operation is subject to the following two conditions:

1.

This device may not cause harmful interference, and

2.

This device must accept any interference

may

cause

Warning

Changes

compliance could void the user's authority to operate the equipment.

I

or

undesired operation.

modifications not expressly approved by the party responsible for

of

the FCC rules and with RSS-21 0

rece~ved,

including

any

PATENTED: www.voxxintl.com/company/patents

of

interference that

36

R410-192-750

ca6154 Install revA

c:ccc:~l/.J~m

Deluxe Vehicle Security

Remote Start System

IMPORTANT

applicable to most

2014 Voxx Electronics

NOTE:

SAFETY

Corporation.

The operation

vehicles.

PRECAUTIONS

and

the Security and Convenience System as described in this

of

vehicles, some functions AND/OR

some

However, due to the configuration

may not

apply. Please

see your

of

installing dealer

for

manual

more information.

is

4280601

Table

of

Contents

Using Your Remote

Arming the Security System .............................................................. 3

Passive Arming Bypass ..................................................................... 3

Bypassing the Shock Sensor ............................................................ 3

Hidden

Disarming the Security System ......................................................... 3

Two Stage Door Activating Trunk Activating Using the Progressive Using the

Programmed Transmitter Notification ................................................ 4

Valet

Eliminating Manually

Car Jack Mode .................................................................................. 6

Alarm

Optional

Personal

Mode ........................................................................................ 5

Overriding the Security System ......................................... 5

Using Your Remote

Remote Start Ready Mode ................................................................ 7

Cancelling Remote Starting Your Remote Start Entering Your Preheating or User Using the Operating the Turbo Timer Mode

Operating the Daily Start Timer .......................................................

Remote Start Safety Features .........................................................

Programmable Run Time

Remote Start Ready Mode .............................................. 7

"Quick-Stop" Feature ......................................................... 9

Control

Function ...................................................................... 3

Unlock (optional)

Release (optional)

Arm

I

Disarm Notification

.................................................................... 3

..................................................... 4

................................................... 4

AUX 1

Protection

(optional) ................................................. 4

Car Finder Feature ........................................ 4

Alarm

................................................. 4

Chirps

..................................... 5

Vehicle Starter ....................................................... 7

Vehicle

Shutdown .................................................................... 8

Vehicle while it is Running via Remote Start .............. 8

Precooling the

213

Hour Start Up Timer Mode .................................. 9

(optional)

............................................................ 8

Vehicle's Interior

I

Run Time Extension ....................... 9

........................................................... 1 0

................................. 8

11 11

LED and Siren/Horn Transmitter Replacing

Warranty

2

Button

Remote

Information ............................................................................ 15

Indications

Functions .............................................................. 13

Control

........................................................... 12

Batteries ................................................... 14

ca6154 Owners revA

Usl'ng

Your Remote Control

Arming

To

arm the system, exit the vehicle, close all doors, then press the

the

Security

System

parking lights will flash 2 times, indicating the system is armed, has (if equipped and connected) and activated the starter indicator

NOTE: The system is equipped with a feature system requires a second press

will blink steadily,

once per second.

of

the

ff)

button to activate an

called Silent Choice.

disable feature. The LED status

audible

response from the vehicle.

Passive

If passive arming is +

~>))

system

passive bypass, press the

Bypassing

Arming

,

the system

will

remain

The

Bypass

enabled

will

in

this

Shock

on your system,

while

the system is disarmed, press

respond with 1 chirp and the LED

temporally

ff)

or

bypassed state

for as

@ button and the system will return to

Sensor

will

turn on. The security

long

as you wish.

ff)

button. The

locked

the doors

If enabled, the

arming

To

exit

normal

status.

@

To

arm the system and ignore the shock sensor press

seconds press NOTE: The system

will

be

defaulted back to normal

Hidden

Alarm

Press the alarm siren

function. The security system

I

horn

Disarming

To

disarm the system press the

indicating the system is disarmed and has

ff)

+

~>))

,

the system will

will only

change the shock sensor setting for one arm cycle and

respond with 1

operation the next time the system is armed.

Function

~>))

button first, within 3 seconds press the

will

arm with "Hidden Alarm

will be

the

silenced

Security

if

the system is triggered.

System

@

button. The parking

unlocked

connected). NOTE:

system requires a second press response from the vehicle. If unlock will

The system is equipped with a feature

of

the

@

button to activate an

your system is set up for 2 step unlock, a third press

activate the

audible

response.

called Silent Choice.

ff)

button, then within 5

long

chirp.

ff)

button to activate the hidden

lights will

Function"

flash 1 time,

in

which the

the doors (if equipped and

If enabled, the

audible disarming

of

*Throughout this manual, than 2 seconds.

2014

Voxx

Electronics

'press' refers to pressing for

Corporation.

All

rights reserved.

less

than 1 second; 'press and hold'

refers to pressing for more

3

Two Stage

Door

Unlock

(Optional)

If this feature is enabled on your system, pressing the

ciJ

only the driver's door. Press

doors.

Activating

If this feature is enabled on your system, pressing and holding the

seconds will open the vehicle's trunk

Activating

If this feature is enabled on your system, pressing the @ and

simultaneously will activate wide range

installing dealer to determine the functionality

the Trunk Release Feature (Optional)

the

AUX 1 Output

of

functions like power window or sunroof automation, please consult your

Using the Progressive Car

Press the

and sound 5 times at low volume, increasing

~>))

button to locate your vehicle. The system will flash the parking lights

again within three seconds to unlock the remaining

or

hatch.

(Optional)

an

optional feature. This feature can be programmed for a

of

your system.

Finder

Feature

in

volume each time the button is

ciJ

button one time will unlock

ciJ

button for 3

buttons

pressed.

Using the Personal

Press and hold the

During panic mode, the normal function The transmitter's

option is installed).

again for 3 seconds. The system will automatically stop after 30 seconds.

Programmed

As a security precaution each time the vehicle's ignition is turn on the status LED

light with flash the number to identify unauthorized transmitters from accessing your vehicle. If you believe an

unauthorized transmitter has been programmed to your system, contact your installing

dealer for assistance.

Transmitter

Protection

~>))

button for 3 seconds to activate the personal protection alarm.

@ and

To

ciJ

stop the alarm, press and hold the

Alarm

buttons can be used to lock and unlock the door (if the

(Panic)

of

the transmitter buttons will be suspended.

Notification

of

transmitters programmed into the system. This helps

~>))

button on the transmitter

4

ca6154 Owners revA

Valet Mode

When valet mode is activated the status LED will light solid, and all security

To

functions will be disabled.

enter or exit valet mode simply follow the 4 steps

outlined below:

1.

2.

3.

4.

Eliminating

System ARM/DISARM chirps can

Turn the vehicle's ignition ON.

Push and hold the programming/valet button.

The LED will turn

on

solid when valet mode is active

Release the programming/valet button.

Arm

I Disarm Notification Chirps

be

toggled

ON

or OFF without entering the

programming feature banks.

1.

2.

Turn the ignition

Press and release the valet/programming button 3 times. The system

will respond with 1 chirp for

ON

then

OFF.

ON

or 2 chirps for

OFF.

Manually Overriding the Security System

Your system can be disarmed without the use

of

the transmitter. This is necessary,

since you will need the ability to operate your vehicle if the transmitter

To

battery fails.

by-pass the alarm system;

is

lost or its

1.

2.

3.

Open the vehicle door. The alarm will sound. Turn the ignition key to the

ON

position.

Within 10 seconds, press and release the valet push button switch.

The alarm system will stop sounding and enter the (by-passed) mode.

start and operate the vehicle normally.

You

can now

5

Car

Jack

Mode

This feature must be turned on

in

system programming, please consult your installing

dealer.

(2)

+

riJ

Triggering Car Jack mode: While the ignition is ON and press and hold

for 2

seconds, the parking lights will flash 1 time and the system will act as follows;

1.

50

seconds after being triggered the siren will chirp for 15 seconds, during this 15 seconds you will be alerted to push the valet button to turn off Car Jack mode. If Car Jack mode is not turned off at this time it will advance to the next step.

2.

Following the 15 second chirps (total time now 65 seconds) the siren

will go into full sound and the parking lights will start flashing.

3.

90 seconds after trigger in, addition to the siren and parking lights, the

IN

system will activate the starter kill. THE SYSTEM WILL REMAIN

THIS

STATE UNTIL THE BATTERY IS DEPLETED.

OVERRIDE THE SYSTEM TO TURN OFF CAR JACK MODE: Turn the ignition OFF then On and press the valet button within 1 0 seconds.

6

ca6154 Owners revA

Using Your Remote Starter

enabled

Remote manual

Start

Ready Mode

transmission.

must

be

your

if

vehicle

equipped

is

with

a

Remote

activate the remote start function, the system must first be

To

Mode.

Start

Follow

.

1

2.

3.

Ready Mode - Manual Transmission Vehicles

the steps While a. b.

Set Place

below

the engine is running by the ignition key;

the parking brake

the transmission

With your foot off the brake times within 2 seconds. The LED lights will

turn on to confirm the system has entered quick stop mode.

Remove the keys from the ignition, the

to enter remote start ready mode.

neutral.

in

pedal, press and

flash 3 times and the parking

will

vehicle will

quick stop mode.

4.

5.

Exit the

vehicle and

Within 1 minute

close all vehicle

step

of

doors. The vehicle will

press the

1,

shutdown and sound 2 short chirps then 1

doors.

button to

@

chirp to confirm ready mode is set.

Only

Remote

in

release the

remain running

the vehicle's

lock

Start

button 2

0

Ready

in

long

Cancelling

The system

Open Open the hood or trunk (if connected)

Press the brake Release Turn the ignition

Remote

will

Start

exit remote start ready mode

Ready Mode

any door

the parking brake

ON

if

any

the following

of

occur:

Voxx Electronics

2014

Corporation.

7

Remote Starting Your Vehicle

To

activate the remote vehicle start function, press and release the 0 button 2 times

within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle's parking lights will turn on

on

(or flash depending

system settings) as a visual indication that the vehicle has

started and is running. If your vehicle stalls or does not start, the system will pause 5 seconds, then try

(a

total

of

2 more times to start the vehicle

3 attempts). The system will pause 5 seconds between each start attempt. If the vehicle does not start after the 3rd attempt, the system will abort the remote vehicle start process.

Remote

Start

Shutdown

Press and hold the 0 button for 3 seconds to turn the vehicle off.

Entering the Vehicle while

1.

2.

3.

Unlock the vehicle's doors. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL! Insert the key into the ignition switch and turn to the

it

is

Running

via Remote Vehicle Start

ON

or RUN

position.

4.

Press the brake pedal. The remote vehicle starter will disengage and

the vehicle will operate normally.

Preheating

or

Precooling the Vehicle's

interior

Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle's interior to your setting.

8

ca6154 Owners revA

User Programmable Run Time I Run Time Extension

The system has the ability to allow the user to extend the time the vehicle will

be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. If your system is set to run

15 minutes and the time remaining

the countdown timer to 15 minutes and your vehicle will continue to

is

4 minutes, extending the

run

time will reset

run

for another 15

minutes. Follow the steps below to extend the vehicle's run time.

1.

2.

3.

Using the

The remote start must already

be

active. Press and release the 0 button 4 times. The system will chirp 1 time and flash the parking lights 4 times to

confirm that the

"Quick-stop"

run

time has been reset.

Feature

If you want to make a short stop and keep your vehicle running (to keep the interior

warm or cool), the quick-stop feature allows you to do this while keeping your vehicle

secure and your keys with you.

engage

To

quick

stop:

1.

2.

Stop the vehicle and place the transmission

in

PARK.

With your foot off the brake pedal, press and release the 0 button 2 times within 2 seconds. The LED will flash 3 times to confirm quick stop is entered.

3.

Remove the keys from the ignition and exit the vehicle. Press the@

button to lock the vehicle's doors if desired.

in

Note: Do not leave children or animals unattended

the vehicle when using the

quick-stop feature.

Operating the 2 I 3

Hour

Start Up Timer Mode

The system has the ability to start the vehicle every 2 ot 3 hours for a 48 hour period.

in

This feature is especially useful

cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. The default setting is 3 hour, Selection between 2 or 3 hour

made

in

option programming.

is WARNING! Be certain that the vehicle is outdoors before using this or any remote starting

device. A running engine produces dangerous carbon monoxide fumes which can be

or

harmful

fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is

garaged.

To

begin

the

2/

3

hour

start

up

timer

mode:

1.

2.

3.

4.

To

exit

the 2

1. OR

1.

Turbo Timer

Turn the vehicle's ignition Press and hold Press the

a.

When set for 3 Hour (default) parking

b.

When set for 2 lights

Release

I

3

hour

the

start

the

valet button.

0

button 4 times, the system

lights 4 times.

2

times.

valet

button.

up

timer

ON

Hour-

mode:

Turn the vehicle's Ignition ON.

Activate the remote

vehicle

start feature using the remote

then

OFF.

will;

- chirp 2 times and flash the

chirp 1 time and flash the parking

control.

This option will

keep the engine running to

down before shutting the engine off.

To engage

1.

2.

3.

the

Turbo Timer feature:

With the vehicle running via the ignition key and your foot off brake

Engage the vehicle's buttons

The

pedal.

simultaneously.

vehicle's

parking

parking brake and press the

lights will

feature has been activated.

4.

Turn the ignition key

OFF,

programmed time has elapsed (1,

To

disengage the

turbo

timer

feature, press the vehicle's brake

allow

the

vehicle's

turn on to verify the Turbo Timer

the vehicle will

3,

or 5 minutes)

turbo to

@J

properly cool

of

and

0

the

continue to run until the pre-

pedal.

10

ca6154

Owners

revA

Operating the Daily Start Timer

The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, while

of

the

vehicle,

countdown timer (the vehicle

finished operating the

pressing both the

will

vehicle

for the day, perform the

&:1

&

0

buttons together

will activate the 24 hour

start 24 hours from this time). Next, When you are

following

steps to complete the

in

range

process.

1. Turn the ignition ON/OFF (vehicle must be disarmed).

2. Within

10

seconds,

while

button twice.

3.

II

Remote Start Safety Features

The

vehicle will

emit 2 chirps and flash the parking lights 4 times.

For safety and security reasons, the system

vehicle starter from activating if any

1.

The

vehicle

hood is open.

of

2. The brake pedal is pressed prior to turning the ignition key to the position.

3.

4.

The engine is over-revved (tach checking only). Valet

mode

is active.

pressing the brake, press and

will

the

following

shutdown

occur:

or

prevent the remote

release

the

ON

0

2014

Voxx Electronics Corporation.

11

LED

and

Siren/Horn Indications

LED

Display

Indications

LED

OFF SLOW FLASH FAST FLASH ON (SOLID)

2 FLASH

3 FLASH

4 FLASH

5 FLASH

...

PAUSE

...

PAUSE

...

PAUSE

...

PAUSE

S"en/HornlndicaUons

Chirps

1

Function

DISARMED

ARMED

PASSIVE ARMING VALET MODE ZONE 2 TRIGGER, HOOD/TRUNK ZONE 3 TRIGGER, DOOR ZONE 4 TRIGGER, SHOCK ZONE 5 TRIGGER, IGNITION

Function

DISARM

2

3 4

5

Parking

Flashes

1

2

3 5

ON (SOLID)

Light

Flash Indications

ARM

DOOR AJAR UPON ARMING

DISARM CAR LOCATOR

I TRIGGERED

Function

DISARM ARM DISARM CAR LOCATOR

REMOTE STARTED

I TRIGGERED

12

ca6154 Owners revA

Transmltter ,Button

Functions

2014 Voxx

Electronics

Corporation.

13

Replacing Remote

Co

.n-trol Battel'ies

1 Way 4 Button Remote

The batteries inside each remote use. When the batteries become weak you distance from the the remote

control will dim.

1.

2.

3.

4.

vehicle

Using a coin,

control. Remove the

batteries and Reassemble Test operation of the remote

Control-

control should last approximately

the remote

To

replace

disassemble

old

battery, observing

replace

the

halves

Model

control will

the remote

the halves

with a new battery.

of the remote

CAT4

will notice the remote

work) deteriorate and the

control

the+/-

control.

batteries:

of the remote

symbols

control

1 year under

control

on

range (the

small

the

normal

LED

on

14 ca6154

Owners

revA

Code Systems, Inc. Limited Lifetime Warranty

Code Systems Inc. ("CODE")

security product (the

"Product"), below) should this Product under manship DURING such defect(s) to repairs

of

the defect(s).

Switches, indicator

chaser for a period

CODE

THE

LIFETIME OF

will

be repaired or

lights,

of

one (1) year from the date

accessories, sold separately,

purchased from an authorized

normal

replaced

warrants to the

ORIGINAL

use and conditions, be proven defective

THE

VEHICLE

IN

(at CODE's option) without charge for parts directly related

and transmitter cases are

of

purchase

are covered by the

the accessory.

This warranty is non-transferable,

non-assignable and is voided when: (1) the Product is

removed from the vehicle in which it was originally installed;

originally installed is transferred to another party.

This warranty does not apply

abuse, improper

installation, alteration, or use contrary to its intended function, fire, flood, or other

to any product damaged by accident,

acts.

In

order for the Product to be repaired defective Product must be returned to an authorized retail sales was originally installed

receipt. The date

must be

of

purchase and year, make and

clearly

indicated on the

or

replaced

CODE dealer

sales

PURCHASER

CODE dealer,

of

this

CODE vehicle

that (except as provided

in

material

or

work-

WHICH IT WAS ORIGINALLY INSTALLED,

similarly

of

the Product.

or

(2) the

warranted to the

'

applicable

vehicle

original

pur-

warranty accompanying

in

which the Product was

physical

or

electrical

natural

under the terms of this warranty, the

and accompanied by a copy

model

of

the

vehicle

in

which the Product

of

the

receipt.

This warranty is

IMPLIED. ABILITY THIS WRITTEN OR INCIDENTAL IMPLIED,

CODE

CODE'S LIABILITY PROVIDED PRICE PAID

ANY

IMPLIED WARRANTIES, INCLUDING

AND

FITNESS

WARRANTY.

DAMAGES

WHATSOEVER.

does not warrant that the Product cannot be compromised or circumvented. THE EXTENT

UNDER

ABOVE AND,

BY THE ORIGINAL

Some states do not so the above also

have other rights which vary from state to state

limitation

exclusive

FORA

PARTICULAR PURPOSE, SHALL

IN

NO CASE SHALL CODE

FOR BREACH

THIS

WARRANTY

IN NO

EVENT

PURCHASER OF

allow

may not apply

and

the

exclusion

to you. This warranty gives you specific legal

CODE MAKES NO

OF THIS OR

IS LIMITED TO

ANY

OTHER

IMPLIED

BE

WARRANTIES EXPRESSED OR

WARRANTY

BE

LIMITED TO THE

LIABLE FOR

ANY

ANY OTHER WARRANTY,

THE REPAIR OR REPLACEMENT

OF

MERCHANT-

DURATION OF

CONSEQUENTIAL

EXPRESS OR

SHALL CODE'S LIABILITY EXCEED THE PURCHASE

THE PRODUCT

or

limitation

WITHOUT INSTALLATION

of

incidental

or

consequential

LABOR.

damages,

rights and you may

OF

2014

Voxx Electronics Corporation.

All

rights reserved.

15

Voxx Electronics

Corporation.

FCC

Customer Service

COMPLIANCE

1-800-421-3209

WWW.CODE-ALARM.COM

This device Industry

This device may not cause

1. This device must accept any interference received,

2. may cause undesired operation.

Warning!

Changes compliance could

16

the FCC rules

complies

Canada. Operation is subject to the

modifications not

or

PATENTED:

with Part 15

void the user's authority to operate the equipment.

www.voxxintl.com/company/patents

of

harmful

expressly approved by the party

interference, and

R410-192-760

and with

following two conditions:

including

RSS-21 0

any interference that

responsible

of

for

ca6154 Owners revA

WARNING

THIS VEHICLE IS

EQUIPPED WITH

A REMOTE

CONTROLLED CAR STARTER

BEFORE SERVICING THIS VEHICLE, REMOVE

THE

MAIN

POWER FUSE

(RED

WIRE) TO

THE CAR STARTER OR

DISCONNECT

THE

VEHICLE BATTERY.

LBL0675

Register

online

at:

.CODE-ALARM.COM

Click

On

Product

Registration

and

Fill

Out

the

Brief

Questionnaire

Thank

you

for purchasing a Code-Alarm product.

We

pride ourselves

on

the

quality

and

reliability

of

all

our electronic products, but

if

you

ever

need

service or have a question, our customer service staff stands ready

to

help.

Contact

us

at

www.Code-Aiarm.com

PRODUCT

PROTECTION:

In

case of

an

insurance

loss

such as fire, flood or theft, your

registration will serve as proof of purchase.

PURCHASE

REGISTRATION:

Registering On-Line

will allow us to contact you

in

the

unlikely

event a safety notification

is

required under the Federal Con-

sumer Safety

Act.

1026350

MAXIMUM INSURANCE DISCOUNT AUTHORIZATION

Dear

Insurance Agent,

The

installation

of my

Code-Alarm automatic (passive) arming security system

in

the

vehicle indicated

below qualifies

me for the maximum discount

mandated by

law

in

some states and

by

insurance company option

in

others. This

vehicle

security system automatically

arms itself

after the doors are

closed

and includes

at

least

one engine

disabling relay

to prevent the engine from being started.

Insured

Signature:

_______________________

Name(pleasepnnt

):

______________

_

Street

Address:

__________________

State:

__________

Zip:

___________

_

Insurance

Company:

_________________________________________

_

Policy#:---------------------------------------------Vehicle Year/Make/Model:

--------------------------------------

Vehicle Identification

#:

-----------------------------------------

The signature

below

certifies that

my

Code-Alarm automotive security system was

installed

on

____

_

___

__

(date)

__

_

Installer

Signature:--------------,--------------------------------

Company:

____________________________________________

_

Address:

--------------------------------Telephone:

________

_

PLEASE COMPLETE AND

MAIL

TO

YOUR INSURANCE

COMPANY

1026673

$2,500.00

I

L

CODE

S

YSTEMS,

Should YOUR

M I

Inc

private passenger vehicle in which the C

makes

T

E

the following

D

warrant

y to

OD dealer and while the system is operational and activated be stolen and not recovered or for theft insurance deductible on your existing insurance not to exceed

purposes,

then subject to the following conditions.

$2.500.00.

This Limited Warranty is effective for thefts occurring within one

w

YOU

as

the

A

origin

R

al

purchaser

E-ALARM ANTI-THEFT SYSTEM is origina

if

YOU

will

be

refunded

(I)

year from the original date registration form has been completed in full and received by the CODE-ALARM Program with postmark that is within five (5) business days from the original date vehicle in which the CODE-ALARM ANTI-THEFT SYSTEM has been in stalled; (C) States

of complete theft report with the police comprehensive vehicle with been receiv

or

theft insurance

YOUR

insurance carrier; and (G) the theft claim with

ed

.

or

in

This Limited Warranty applied solely to passenger vehicl

America or Canada; (D) the theft of

not apply to any vehicle used

in

a business. for Livery or offered f

other l

force

Y

OU

R

vehicle occurs within the United

aw

enforcement agency having

on

the vehicle at the

es

, motor homes, and light duty trucks

or

of

purchase; (B)

YOUR

States

juri

time

YOUR

of

sdiction

the

theft

and

YOU

insurance carrier is settled and final payment from them has

hire. This Limited Warranty applies only to the vehicle as identified on

the attached registration form .

In

order

to

make

a claim

under

following information

and

the Limited Warranty, YO U

materials:

•

Proof

of

YOU

•

purcha

ARE

URGED TO

A certified or

se

notarized c

are to

provide

the

including the purchase date.

SAV E

YOUR O

omp

lete copy of the police report filed by

RI

GINAL RECEIPT

CODE-ALARM

R

of

this

A

N T

sys

tem.

ll

y installed by an authorized

y

stolen and recovered be deemed a total loss

the

comprehensive

of

purchase providing that: (A) the attached Administrator YOU

at

the address shown below

properly and completely identify the

auto

insurance

vehicle is registered within the United

of

Am

erica

or

Canad

a; (E)

YO

U

at

the location of the theft; (F)

have filed a claim for

or

vans not exc

ee

Program

Y

OU

ding 13,500

Administrator

the

YOU

theft

GVW.

file

have

of

the

It

does

with the

a

•

CONTINUED

THIS

OF

ON

CARD

YOUR

REVERSE

MUST

BE

CODE-ALARM

RETAINED

CONSUMER

Co

de-Alarm Anti-Th

Na

me

Ci

ty

Vehicle Year M

In

s

ur

ance

Carr

Amount

of

D

ea

l

er

Name A

Price Paid

OPTI

ONA

Annual Household Income: Less than

ef

t

Sy

stem

Purchased Purchase Date

i

er

Com

rehen

sive

or

Th

For

S

stem Was

L

IN

FORMATI

ON

A copy of the original declaration sheet from the insurance policy in force at

the time

of

the sy

st

em purchase. This declaration sheet must clearly

show the amount of the deductible applicable to theft losses

A

copy of the insuran

ce

c

omp

any settlement check and any related documentation

ADV-

POSTMARKED

ANTI-THEFT

AND

SUBMITTED

State

ake/Model

eft De

du

ctible

A e of Buver:

S

520.000

WITHIN

THIRfY(30)8USINESS

SYSTEM.

WITH

ORIGINAL

ANY

CLAJMFn,ED

REGISTRATION

Address

Zi

p

VI

N

Po

li

c

ddr

ess In

s

ta

ll

a

ti

on

In

cluded

Purchased lor:

D

$20-40.000

D

PURCHASE

Phone

''

Y

es

D

Yourself

$40-60.000

DAYS

HEREUNDER

CARD

D

As a

D

OF

THE

RECEIPT

No

D

Gi

ft

D

More than

PURCHASE

MUSf

$60,000

BE

D

BY

YO

UR SI

GNA A THI

Sign

ND

S

at

(2) LIMIT

ur

e

Y

OU

UNDERSTAND

ED

WARR

TURE B ELOW,

ANTY IS

YO

U

A

ND

AGREE

NO

T

AN

(II

AGREE

TO

THAT

C

INSURA NCE PO

OD

ALL

E SYS

OF

THE

TERM S

A

ND

COND

I

TION

S S

ET

I'ORT

H IN T

HI

S

LI

MI

TED

W

ARRAN

TE

M

S,

Inc

IS P

ROV

IDI

NG

YOU

WIT

H A

LIM

ITED

WA

RR

LI

CY

Da

te

ANTY

AND

10

THAT

26699

TY

The CODE-ALARM Program Administrator reserves the right to ask for any other similar documentation that may be reasonably required to verify

Program Administrator's property and will not be returned.

YOUR

claim. All documentation received

on

a claim becomes the Code-Alarm

or

other

materials

All claim information must be mailed to the Code-Alarm Program Administrator within thirty

of

the final settlement check from YOUR insurance carrier.

For the protection mail or any other means such that Alarm Program Administrator is not responsible for materials not received in the CODE-ALARM Program Administrator's office. Please allow four (4) to six (6) weeks to process any claim hereunder.

This limited warranty is not an insurance policy or insurance coverage and underlying comprehensive auto insurance coverage and your compliance with all the terms and conditions set forth herein. This limited warranty has no cash value and is subject to all the terms and conditions set forth within this document.

This warranty

WARRANTY CASE SHALL CODE-ALARM QUENTIAL

IMPLIED, WHATSOEVER. No person expressed herein in connection with the sale

Some states do not allow limitations on how damage so the above limitations also have other rights which vary from state to state.

of

YOUR rights, YOU are urged to make copies

is

in lieu

of

OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY, IN NO

OR

THIS WARRANTY AND WARRANTY PROGRAM

all other express warranties

INCIDENTAL

YOUR package can be traced in the event

or

liabilities. ANY IMPLIED WARRANTIES , INCLUDING ANY IMPLIED

OR

THE CODE-ALARM PROGRAM ADMINISTRATOR BE LIABLE FOR ANY CONSE-

DAMAGES

or

exclusions may not apply to YOU. This warranty gives YOU specific legal rights and YOU may

MARKETED

FOR

or

long an implied warranty lasts

BREACH

representative is authorized to assume for the Company any liability

of

this product.

IN

OR

of

all materials submitted and to send all materials via registered

OF

THIS

FROM THE STATE OF FLORIDA.

IS

of

its becoming lost

is

contingent on the existence

OR

ANY

OTHER

or

the exclusion or limitation

NOT AVAILABLE AND

(30) business days after receipt

or

misdirected. The Code-

of

and payment from an

WARRANTY,

of

MAY

EXPRESSED

incidental

NOT BE

other

or

consequential

OR

than

CCJCC~L/.I~m

THE

CODE-ALARM

CODE-ALARM LIMITED WARRANTY PROGRAM

PROGRAM

Post Office

Encinitas,

Box CA

ADMINISTRATOR

231809

92023

Phone (800) 708 2113

Post Office

Encinitas,

Box

CA

23 1809

92023

POST OFFIC

WILL DELIVER

WITHOUT

POSTAGE

HERE

NOT

PROP AFFIX

E

ER ED