Code Alarm ca5553sst Installation Manual

CCCJc:~lA~m

r:»~OFESSIONAI

SE~IES

Automatic

Remote

Start

Installation

ca5553sst

I

Manual

with

for

models:

Transmission

Keyless

Entry

Guide

2012

Audiovox Electronics Corporation.

All

rights reserved.

4280478

Table

Contents

of

Before Wire

11

3 Pin Parking Light Harness ..................................................................... 8

6 Pin Start 4 Pin

2 Pin Door Lock Harness ........................................................................

Add

Antenna DBIPort Telematic Interface

You

Connection

Pin Main Harness ................................................................................. 5

Alternate

ion

it

Begin

Harness ................................................................................... 9

Ports

a I

LED

I

.................................................................................................... 15

...................................................................................... 3

Guide

Harness .......................................................................... 1 0

........................................................................... 4

...................................................................................... 15

Programming Port ....................................................... 15

I

Port .......................................................................... 15

11

Programming

&

Up

Set

Transmitter Programming ........................................................................ 16

Manual

Programming Feature Banks .................................................................. 17

Tach Programming .................................................................................. 19

Smart

Feature Transmitter Remote System

Feature Programming ................................................................. 16

Tach less Mode ............................................................................. 19

Descriptions

Button Start Layout

Shutdown

......................................................................................... 28

.......................................................................... 16

.............................................................................

Functions

Diagnostics

............................................................. 26

................................................ 27

20

2

ca5553sst rev A

BEFORE YOU BEGIN

PROFESSIONAL INSTALLATION

STRONGLY

Roll down window to avoid

RECOMMENDED

locking keys

in

vehicle

during installation

Avoid mounting components or routing wires near hot surfaces

Avoid mounting components or routing wires near moving parts

•

. . . .

Tape or

loom

wires under hood for protection and

appearance

Use a Digital Multi

circuits. DO NOT USE

Meter for testing and verifying

A

TEST LIGHT, OR

"COMPUTER SAFE PROBE" as these can set off air bags or damage

Technical Support

http://techservices.codesystems.com

vehicle

or go to

computers.

(800)

421-3209

2012

Audiovox

Electronics Corporation.

All

rights reserved.

3

Pin Main Harness

11

GRAY/RED PURPLE DOOR INPUT GREEN

PARKING

BRAKE

DOOR INPUT

( (

+)

- )

INPUT

(-

)

z

<(

~

z

a..

~

(/)

zr-

-:x:

a..(!)

-

('f)

.....J

BLACK/WHITE ILLUMINATED ENTRY

BROWN/BLACK

HORN OUTPUT RED/WHITE TRUNK RELEASE BLUE/BLACK

PURPLE/WHITE GRAY

BROWN/RED VIOLET/BLACK

START STATUS

TACH

INPUT HOOD PIN INPUT BRAKE

AUX 1

INPUT (

OUTPUT

3 Pin Parking Light Harness

BLACK WHITE/RED PARKING LIGHT INPUT WHITE

GROUND

PARKING LIGHT OUTPUT

OUTPUT

- )

(

OUTPUT

ACTIVE OUTPUT ( - )

I

- )

(

( - )

+ )

(-)

6 Pin Start Harness

PURPLE STARTER

r-

0:::

<(

r-

(/)

z

a..

<0

4

RED BATTERY 12V ( ORANGE ACCESSORY 1 ( + ) PINK/WHITE IGNITION RED/WHITE

PINK

OUTPUT-

( + )

2

BATTERY 12V (

+)

(

IGNITION

1

MOTOR SIDE

+)

ca5553sst rev A

4 Pin

Alternate

Harness

z~

-(.)

a..

C\I_..J

1

a

11

GRAY/RED

BLACK/YELLOW GREEN/WHITE PULSE AFTER SHUTDOWN LT BLUE L T GREEN/BLACK

PULSE DURING CRANK ( - )

FACTORY FACTORY DISARM

2 Pin Door Lock Harness

BLUE GREEN

UNLOCK LOCK

(-)

Pin Main Harness

PARKING

ARM

I

PULSE

I

PULSE BEFORE START ( - )

(-)

BRAKE INPUT

( - )

AFTER

(-)

START (

- )

Locate the vehicle's

Verification:

parking brake wire.

This wire

will

register ground when the

vehicle's PARKING

BRAKE is engaged.

NOTE: The

following

connection is required for

Manual

Transmission

Mode.

2

Locate the

PURPLE

vehicle's

Verification:

opened and the interior

dome

This wire

light

or door pin switch wire.

will

light is on. This wire will

register ground or "0" Volts

DOOR TRIGGER INPUT

(

+)

register positive voltage (POS) when the door is

when the door is closed

and the interior light

off.

Connect the PURPLE wire to the vehicle's positive door input wire(s).

NOTE:

Certain vehicles may require multiple connections. Refer to vehicle

application guide.

is

2012

Audiovox

Electronics

Corporation.

All

rights reserved.

5

3

GREEN

DOOR TRIGGER INPUT

-)

(

Locate the

and the interior light is on. This wire

vehicle's dome light or door pin switch wire.

Verification:

This wire will

register ground (NEG) when the door is opened

will register positive

voltage when the

door is closed and the interior light is off.

Connect the GREEN wire to the vehicle's negative door input wire(s).

NOTE:

Certain vehicles may require multiple connections. Refer to vehicle

application guide.

4

BLACK/WHITE ILLUMINATED

This wire provides a ( - )

500mA

output for

ENTRY OUTPUT

seconds when the system is

30

(-)

disarmed capable of driving relays. Locate the vehicle's dome light or pin switch wire.

Verification:

vehicle's

This wire will register positive voltage or ground when the

dome

light is turned ON.

5

BROWN/BLACK HORN

OUTPUT (

- )

Locate the vehicle's horn wire.

register at positive voltage and register

Verification:

This wire

will

ground when the horn switch is pressed.

Connect the BROWN/BLACK wire to the vehicle's horn wire. This is a low current

output,

6

500mA.

RED!WHITE

TRUNK

RELEASE

OUTPUT

(-)

Locate the vehicle's trunk release wire at the trunk release switch.

Verification:

This wire

will register either positive voltage or ground when

the trunk release is activated.

option programming.

This is a low current output,

500mA

and is configurable

in

6

ca5553sst rev A

7

BLUE/BLACK

START STATUS

I ACTIVE

OUTPUT

(-)

This wire provides a ground output when the remote start function is activated and remains until 4 seconds after the remote start is shutdown. be used for multiple application's a

1 amp diode is required in-line with the stripe

If

this wire

will

facing the control module.

8

PURPLE!WHITE

TACH

INPUT

Locate the vehicle's ignition coil or fuel injector in the engine compartment.

Verification:

1.

Set voltmeter to AC

2.

Attach positive lead of a volt meter to a constant 12-volt source.

3. Attach negative lead of a

Test using the following

VOLTS.

volt meter to the wire to be tested.

procedure:

4. Start the engine.

5.

Have someone press on the gas pedal slightly as you monitor the meter. If connected to the correct wire, the voltage reading

will

increase as the engine's

RPM increases.

Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition or

fuel

injector.

9

GRAY

HOOD PIN INPUT

(-)

coil

Install

a Hood Pin Switch and connect to the GRAY wire. This connection is

required for Remote Start.

Verification:

This wire when connected

vehicle's hood is opened.

Connect the GRAY wire to the hood pin.

NOTE:

1

0

Be sure to

loom

BROWN/RED BRAKE INPUT

Locate the vehicle's brake light wire at the brake pedal mounted switch. This

connection is required for Remote Start.

Verification:

This wire registers positive voltage when the brake pedal is

pressed.

Connect the BROWN/RED wire to the vehicle's brake light wire.

2012 Audiovox Electronics Corporation.

will

register ground when the

the wire, and seal the grommet.

(

All

rights reserved.

+)

7

11

VIOLET/BLACK

AUX 1

This wire provides a

( - ) 500mA output capable of driving relays. For Control of

optional accessories (i.e. Power Window/Sunroof, etc.).

activate refer to the transmitter button configuration chart. Please refer to the

To selectable options for timing.

3 Pin Parking Light Harness

1

BLACK

Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended grounding point is a metal surface

the driver's side kick

in

not ground the BLACK wire with any other vehicle components.

NOTE:

Do

panel area.

GROUND

2

3

WHITE/RED

WHITE

PARKING

LIGHT INPUT

LIGHT

OUTPUT

Locate the parking light output wire at the vehicle's light switch.

Verification:

This wire registers positive voltage when the parking lights are

turned on.

Positive switching Parking Lights:

Connect the

WHITE/RED WHITE

wire to the parking light output wire.

wire to a 15 Amp max fused battery source.

Negative switching Parking Lights:

Connect the WHITE/RED Connect the

WHITE

wire to the parking light output wire.

wire to a good chassis ground.

8

ca5553sst rev A

6 Pin Start Harness

1 PURPLE

STARTER

OUTPUT

(

+ )

Locate the vehicle starter wire.

Verification:

This wire registers voltage

only

when the key is turned to the

START position.

Verification:

The starter wire registers voltage when the key is turned to the START position.

Connect the PURPLE wire to the vehicle starter wire.

2 RED

BATTERY

12V

(

+ )

Locate 1 of the vehicle's constant 12 Volt battery wires at the ignition switch.

Verification:

This wire

will

register (

+ )

voltage in

all

positions of the ignition

switch.

Connect the RED wire to the constant 12

NOTE:

3

Remove

ORANGE

all fuses until

all

connections are made.

ACCESSORY

Volt battery wire.

1

(

+ )

Locate the vehicle's accessory wire at the ignition switch.

Verification:

(Accessory) and the ON

This wire registers voltage when the key is turned to

(or RUN) position. The voltage drops out when the

key is turned to the START (or CRANK) position.

Connect the ORANGE wire to the vehicle's accessory wire.

4

PINK/WHITE

IGNITION 2 (

+ )

Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped).

ACC

Verification:

This wire registers voltage when the key is turned to the RUN) position, but not the drop out when the key is turned to the START (or CRANK) position.

Connect the

PINK/WHITE wire to the vehicle's ignition 2 wire.

Programmable output:

2012

Audiovox Electronics Corporation.

IGN, ACC,

All

rights reserved.

ACC

ON

(or

(Accessory) position. The voltage does not

Start.

9

!WHITE

5

RED

Locate 1 of the vehicle's

Verification: This wire

constant 12

will

BATTERY 12V (

battery wires at the ignition switch.

Volt

register (

+ )

voltage in all

switch.

Connect the RED/WHITE wire to the constant 12

+ )

battery wire.

Volt

positions of the ignition

NOTE:

6

PINK

Remove

fuses until

all

all connections are made.

+)

(

IGNITION

1

Locate the vehicle's ignition wire at the ignition switch.

Verification:

This wire registers voltage when the key is turned to the RUN) position. The voltage does not drop out when the key is turned to the START (or CRANK) position.

Connect the

PINK

This wire is also

wire to the

used for

vehicle's Ignition

Ignition

1 Output.

wire.

4 Pin Alternate Harness

1

BLACKNELLOW

PULSE

DURING CRANK

ON (or

(-)

Locate the

vehicle's second starter (crank) wire at the ignition switch. (if equipped)

in the start (crank) position of

Verification: This wire registers voltage

only

the ignition switch.

Connect the BLACK/YELLOW wire as shown in the diagram below. Use an relay (not supplied).

This output is configurable in option programming.

2

GREEN/WHITE

This wire

typically

is shutdown.

PULSE AFTER SHUTDOWN

500mA pulse after the remote start shuts down. This

will

supply a

( - )

used to re-lock the vehicle's doors if they unlock upon remote start

be used to pulse a door pin-switch wire to prevent the

also

can

It

(-)

vehicle's accessories from remaining on after remote start shutdown.

option programming.

This output is configurable

in

SPOT

10

ca5553sst

rev

A

3

LTBLUE

FACTORY ARM

I

This wire

will supply a

(-)

500mA

PULSE AFTER START

pulse both upon arming the system and upon

(-)

successful completion of the remote start activation sequence and is typically used to re-lock the vehicle's doors upon remote start if necessary.

This output is configurable in option programming.

4

This wire will

LT

GREEN/BLACK

supply a ( - )

FACTORY DISARM PULSE

BEFORE

I

START

(-)

500mA pulse both upon disarming the system and when

the remote start feature is activated. Locate the factory perimeter alarm disarm

wire from the key cylinder inside the drivers door.

Verification:

position

This output is configurable

This wire registers ground if the key is turned to the unlock

in

the driver's door cylinder.

in

option programming.

2 Pin Door Lock Harness

1

2

The door systems which may require additional parts. Please review the wire and location chart to see which type of door

types are shown

BLUE

GREEN

lock

UNLOCK

LOCK

I

unlock outputs are designed to control several different types of

lock

system is

in

the following diagrams.

(-)

in

your

vehicle.

The most common

2012

Audiovox Electronics Corporation.

All

rights

reserved.

11

Negative

Switching

Locks

Door Lock and

All unlock

switch.

Verification:

Unlock: Locate the

These wires

will

lock I unlock

register ground when the Lock and

switches are activated.

Connect the GREEN and BLUE wires shown

Negative Locks:

Lock Output

GREEN(-)

Unlock Output

BLUE(-)

wire at the

the diagram

in

Door Lock

Vehicle

Relays

Control

vehicle's lock I

Unlock

below.

Positive

Switching

All Door Lock and unlock

switch.

Verification:

Unlock

switches are activated.

Locks

Unlock:

Locate the

These wires

lock

register positive

will

I

Connect the GREEN and BLUE wires shown

Positive Locks:

Door Lock

Vehicle

Relays

Control

unlock

in

wire at the vehicle's lock

the diagram

voltage

I

when the Lock and

below.

-) Lock Output

GREEN(

Unlock Output

BLUE(-)

12

ca5553sst

rev

A

Reverse Polarity Locks (S-Wire Door locks)

Door Lock and

All

Unlock:

Locate the

lock

unlock wire at the

I

unlock switch.

Verification: These wires

voltage

when the Lock and Unlock

will rest at ground and register positive

switches are activated.

Connect the GREEN and BLUE or BLUE/GREEN wires shown

supplied).

below

using (2)

SPOT relays

Reverse

(not

Polarity

Locks:

GREEN(-)

BLUE

Output

Lock

Unlock Output

(-)

vehicle's lock

the diagram

in

I

To Door Lock Motor

Negative

Multiplexed

All Door Lock and

Locks

Unlock:

Cut

Locate the

--------~

unlock wire at the

I

lock

unlock switch.

Verification: This wire will show

Please consult the wire and

your

vehicle.

location

variable

ground when the switch is activated.

chart for specific resistor

Connect the GREEN and BLUE or BLUE/GREEN wires shown

supplied).

below using (2)

SPOT relays

(not

Multiplex Locks:

vehicle's lock

values

the diagram

in

I

for

2012 Audiovox

Electronics

Corporation.

rights reserved.

All

13

Positive

Multiplexed

Locks

All Door Lock and Unlock: Locate the lock I

unlock wire at the vehicle's lock

unlock switch.

Verification:

This wire

will

show variable positive voltage when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown below using (2) SPOT

relays (not supplied).

Multiplex Locks:

Vehicle

Door Lock

Control Relays

in

the diagram

I

Adding Aftermarket Actuators

After installing BLUE wires shown

aftermarket actuators, (not supplied). Connect the GREEN and

in

the diagram below using (2)

---------1

87

.------4111..._----1

87

Fused

+

12

Battery Source

Fused Battery Source

Volt

+

12

Volt

SPOT

relays (not supplied).

BLUE (-) Unlock Output

14

ca5553sst

rev

A

Additional Ports

Antenna I LED I Programming Port

Mount the supplied antenna/receiver to a clear spot

that will not block the driver's vision. A good location is usually high

Be

windshield near the rear view mirror.

careful not to mount the antenna/receiver

on

the vehicle's windshield

on

the

on any metallic window film, as this will effect system range. Route the antenna/

receiver cable to the control module and plug into the antenna port.

Data Bus Interface Port

This 4 pin port is used for Flashlogic Door Lock and Transponder Databus

Interfaces to communicate with the vehicle's Databus. When using the

OBI

port to control the Flashlogic Door Lock and Transponder Interface modules the following options may function list available per vehicle

Tach

Input Brake Safety Shut Down

be

available. Please refer to the

on

the tech service web site.

020

(Data to Data)

Trunk/Hatch Open Diesel Glow Plug Input Door Lock Control Passlock I Passkey Interface (GM Only) Dome Light Supervision Transponder Interface Activation Factory Alarm Arm

I Disarm Manual Arm I Disarm Inputs (factory keyless

controls system)

Telematic Interface Port

This 4 pin port is used for Telematic Interface accessories, such as Carlink, which can control some of the following features.

Door Lock Control Trunk Release Sliding Doors AUX Output Car Find Remote Start

2012 Audiovox Electronics Corporation.

All

rights reserved. 1 5

Set Up & Programming

Transmitter Programming - Feature Bank 1

1.

2.

3.

4.

5.

6.

Turn the ignition ON.

Press and hold the valet/override button.

Within 10 seconds the system will chirp (3) three times.

Press 1 button of each transmitter you wish to program.

The system will respond with 1 chirp for each accepted transmitter.

Pressing the override button at anytime during programming will advance to

the next bank.

NOTE: The system will exit transmitter programming after 15 seconds of inactivity. NOTE: This system has 1 button programming which programs all channels of the

system.

NOTE: The system will hold up to 4 transmitters

transmitter will erase the oldest transmitter

in

memory, programming a 5th

memory.

NOTE: This system has PTN - Programmed Transmitter Notification. Each time the

ignition is turned ON, the LED will flash the number of transmitters programmed to

the system.

Manual Feature Programming - Feature Bank 2 - 5

1.

2.

3.

4.

5.

6.

Defaulting All Features: Pressing the

feature banks will default all features and return you to feature bank 2 - 4 chirps.

Turn the ignition ON. Press and hold the valet/override button. Within 1 0 seconds the system will chirp (3) three times. Use the valet/override button to advance through each option bank. For

feature programming advance to Feature Bank

4 or

5,

which is (4)

2,

3,

four, (5) five, (6) six and (7) seven chirps.

Use the transmitter 0 button to scroll through the selections

in

each feature

bank, the system will chirp to match the feature number. Press the transmitter @ button to change the desired feature. The LED will

flash indicating the changed feature.

~

button anytime while

in

any of the

NOTE: The system will remain

ignition is on, there is no time limit.

16

in

feature programming mode as long as the

To

exit programming turn the IGNITION

OFF.

ca5553sst

rev

A

Feature

Transmitter

Bank

1

-

Programming

3

Chirps

Refer to transmitter programming.

2012

Audiovox Electronics

Corporation.

All

rights reserved.

17

Feature

Pin Alternate

4

Black

Bank

5 -

Output

I

Yellow Output

7 Chirps

Control

Pulse

During

Crank Running

Ground

While

Ignition

NOTE: On

this

model

the

Lt

Green I

Black

18

Output

will

wire

can

override

be

configured

changes made

in

Bank

in

Bank

3

or

Bank

5.

Any

3.

changes

to

this

feature

ca5553sst

in

Bank

5

rev

A

Tach Programming

The unit tachless option

remote start without first programming tach, times indicating tach has not been learned and stored.

will

not operate

is

turned ON.

unless

If

an attempt is made to start the vehicle via the

a tach signal

the unit

is programmed or the

will

flash the parking lights 7

If

the tach rate is not

properly programmed to the specific vehicle, the unit may not realize that the vehicle is running

The Remote

Start

packs, or single injector.

1.

2.

3.

4.

Turn the ignition key to the ON Press and release the valet/override button 3 times. Immediately Press and hold the valet/override button, then start the vehicle using

the

5.

When the unit senses the tach signal, the parking lights

unit

key.

in

certain instances and reengage the starter motor.

will

learn the tach rate of most vehicle's single coil, multiple coil

To

learn tach:

position.

turn the ignition key

OFF.

will begin to

flash.

6.

Allow the vehicle to settle to a normal idle speed.

7.

Release the valet/program push-button switch. 1 long chirp and the parking lights

will

turn

on

for 2 seconds, indicating that the learned

tach signal is stored and the unit has exited tach learn mode.

NOTE:

poor tach source, the parking lights will

If

the unit fails to learn tach rate due to

not flash.

an

improper tach connection or a

To

correct this situation, locate

and connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach learn routine.

Smart Tachless Mode

Smart Tachless Mode is available only if a tach signal has never been learned to

the system and when activated

in

option programming to Tachless without the need to enter the feature

programming mode.

1.

Activate the remote start. The parking lights should begin flashing 7

times indicating no tach signal has been learned.

will

automatically change the

Tach

Mode feature

2.

3.

Within the 7 flash time period, press and hold the

The system mode.

2012 Audiovox Electronics Corporation.

All

()

button.

will chirp 1 time indicating the system is now

rights reserved.

in

tachless

19

Feature Descriptions

Feature Bank 2 - Security

1 - Silent Choice: Controls the normal arm/disarm chirps of the security system.

ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/unlock buttons.

OFF - normal arm/disarm chirps upon the first press of lock/unlock.

2 - 8 Not available on this model.

OBI

9 -

Port Protocol: Determines the protocol type

interface with external modules.

OBI

Protocol

in

which the

OBI

port uses to

ADS Protocol

Feature Bank 3-Output Control

1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock

output wires.

1 Second - Single 1 second lock pulse, single 1 second unlock pulse.

3.5 Seconds - Single 3.5 second lock pulse, single 3.5 second unlock pulse. 1 Second Lock, Double Pulse

Unlock-

second unlock pulse. 30 Second Lock, Double Pulse

Unlock-

1 second unlock pulse. Double Pulse Lock, 1 Second Unlock - Double 1 second lock pulse, single 1

second unlock pulse.

Single 1 second lock pulse, double 1

Single 30 second lock pulse, double

20

ca5553sst rev A

2-

Factory

output.

Factory Disarm - Single 1 second pulse with unlock and remote start activation.

2nd Unlock - Same output as unlock with 2nd press of unlock. . Start Status - Single 1 second pulse with unlock and continuous ( - ) output

during the remote start cycle.

Disarm: Controls the timing of the

LT.

GREEN/BLACK factory disarm

NOTE: 3 or Bank Bank

3 ON

On

5.

3.

Ignition or

OFF.

OFF-

this model the Lt Green I Black Output wire can

Any changes to this feature

Controlled

Door locks not activated by ignition.

Lock and Unlock - Doors lock when ignition is turned ignition is turned off.

Lock

Only-

Doors lock when ignition is turned on only.

Unlock Only Doors unlock when ignition is turned off only.

4 -

Trunk

Output

Timing

of the RED/WHITE output.

1 Second

Pulse-

1 second pulse output.

1 0 Second - Continuous output for 1 0 seconds.

Locks:

Control of door locks when the ignition is cycled

- Red/White

be

configured

in

Bank 5 will override changes made

on

and unlock when

Output:

Controls the output timing/type

in

Bank

in

20 Seconds - Continuous output for 20 seconds.

ON

Latched until IGN

- Continuous output until the vehicle's ignition is turned

ON. Latched ON until Button Press - Continuous output until the activation button

is pressed again.

5 -

Horn

Output

Timing:

Control the minimum horn pulse time

in

milli seconds,

some vehicle will require a longer pulse to activate the factory horn.

16mS 1

OmS

30mS 40mS 50mS

6 - Real Panic: Controls the panic out when triggered from the transmitter.

ON

- Randomized horn honks when panic is triggered.

OFF - Standard pattern horn honks when panic is triggered.

21

7-

AUX 1: Controls the

VIOLET/BLACK

AUX 1 output activation type and timing.

Push and Hold

- Output

is

continuously active

until

transmitter button is

released. Latched - Output stays active Latched

until IGN ON

-Output

Dome Light Output - Output used for

until

button is pressed again.

stays active

illuminated

until

the ignition is turned on.

entry and is not

controlled

by the AUX 1 function of the transmitter. Defrost Output Defrost Output Latched 5 Minutes -

Single Pulse

- Single 1 second 5 minute continuous output after

pulse

after start

remote start.

Feature Bank

1 - RF

2 - Run Time: Controls the time under control of the remote start

Start

4-

Remote

Start Control

Chirp: Turns remote start activation confirmation chirps

in

minutes that the vehicle

until

the system times out. The system may

will

stay running

ON or

be shut down at any time by use of the transmitter or system shutdowns.

OFF.

also

3-

Running Lights: Controls the

WHITE parking light output wire during remote

start.

Steady - Parking

lights

constant during the remote start cycle.

Flashing - Parking lights flash at a slow pace during the remote start cycle.

4

- Tach Mode: Determines how the system monitors the engine running during

remote start.

Tach - Hard wired directly to the tach wire of the

vehicle

to monitor AC

voltage. Tachless (Crank AverageNoltage) - Determines crank time by averaging the

last 8 times the vehicle was started with the key and then monitors the change

Hybrid (Crank Average

the

OBI

connected to the

in

voltage after remote start.

I

No Voltage) - Determines crank time by averaging

last

8 times the vehicle was started with the

Port - Monitors the vehicle's tach rate through

OBI

port.

key.

an

interface module

22

ca5553sst

rev

A

5 - Voltage Level: The voltage variance for remote start when set to tachless.

(see tach mode)

HIGH

-The

variance

in

battery voltage from before the remote start

is activated to after the engine is running must be greater than 0.5 volts. LOW-

The variance

in

battery voltage from before the remote start

is activated to after the engine is running may be less than 0.5 volts.

6-

Crank

Time: Preset output times for the PURPLE starter wire.

1 Second 0.8 Seconds 1.5 Seconds 2 Seconds 4 Seconds

7 -

Crank

Average I

Crank

Time: The length of time

in

which the remote start

will crank the vehicle's starter.

Crank Average - Determines crank time by averaging the last 8 times the

vehicle was started with the key.

Preset Time - Preset starter output time. (see crank time)

8 - Gas I Diesel: Selects engine type and delay time for the starter output wire

during remote start activation.

Gas - Gasoline engine, no delay for the starter output wire.

1 0 Second Delay - Diesel engine, delays the starter output wire for 1 0

seconds after the ignition has been powered up by the remote start.

15 Second Delay - Diesel engine, delays the starter output wire for 15

seconds after the ignition has been powered up by the remote start. 20 Second Delay - Diesel engine, delays the starter output wire for 20

seconds after the ignition has been powered up by the remote start. 45 Second Delay - Diesel engine, delays the starter output wire for 45

seconds after the ignition has been powered up by the remote start.

9 -

Single I Double

Pulse Start: Switches the remote start activation between

a single or double press from the transmitter.

10 - IGN 2

Output:

Programmable high current output.

Ignition 2 - Ignition output during remote start. Accessory - Accessory output during remote start. Start

11

- 2

2012 Audiovox Electronics Corporation.

I Crank - Crank output during remote start.

or 3 Hour

Start: Not available on this model.

All

rights reserved.

23

12 - Turbo Timer:

Not available on this model.

13 - Transmission Mode:

Select the type of remote start activation based on

the vehicle's transmission type.

Automatic - For use with automatic transmission vehicles. Standard remote start operation. Manual - For use with manual transmission vehicles. Remote start ready mode must

14 - Temperature Start:

be

set upon exit of vehicle to enable remote start.

Sets the threshold temperature for temperature start

mode. When temperature start is activated, the remote start function

when the ambient temperature drops below the selected temperature.

Feature Bank

1 -

Black/Yellow Output

5-4

Alternate

:

Controls the

Output

Control

BLACK/YELLOW

output activation type

and timing.

Pulse During Crank -

Output

becomes active with the same timing as the

starter output wire, during crank only.

will

activate

Ground While Running - Continuous output for the entire remote start

sequence until after the vehicle shuts down.

Ignition

and does not drop out during crank. Accessory -

output, drops out during crank.

2-

Green/White

timing.

Pulse After Shutdown - 1 second pulse after the remote start has

shutdown.

Ground While Running - Continuous output for the entire remote start

sequence until after the vehicle shuts down.

Ignition- Output

and does not drop out during crank.

Accessory output, drops out during crank.

- Output

becomes active with the same timing as the ignition output

Output becomes active with the same timing as the accessory

Output:

Controls the GREEN/WHITE output activation type and

becomes active with the same timing as the ignition output

Output

becomes active with the same timing as the accessory

Pulse During Crank - Output starter output wire, during crank only.

24

becomes active with the same timing as the

ca5553sst rev A

4 - Lt Green/Black Output :

type and timing.

During Unlock - 1 second pulse when remote start is

Pulse before Start

activated. Also

I

1 second

a

Controls

pulse

GREEN/BLACK output activation

LT

the

when unlock is pressed.

3-

Ground

While

sequence

Ignition

-Output

Running -Continuous output for the entire remote start

until after the vehicle

shuts down.

becomes active with the same timing as the ignition output

and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank.

Pulse starter output wire, during crank

Blue

Lt

Pulse sequence and has confirmed the when unlock

Ground sequence until after the

Ignition-

During Crank - Output becomes active with the same timing as the

only.

Output:

After Start

Controls

During Lock - 1 second pulse

I

the

after the remote start

vehicle is running.

Also

a 1 second pulse

BLUE output activation type and timing.

LT

is pressed.

While Running - Continuous output for the entire remote start

vehicle

shuts down.

Output becomes active with the same timing as the ignition output

and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank.

Pulse

During Crank - Output becomes active with the same timing as the

starter output wire, during crank only.

2012 Audiovox Electronics Corporation.

rights reserved.

All

25

Transmitter Button Functions

1

Way

Press Unlock + Start While Armed

26

ca5553sst

rev A

Remote

Start Shutdown

Diagnostics

the remote start shuts down or

If

the patterns below

manually

To

enter diagnostics and view the

and press and

FLASHES

LED

3 Flashes

indicating the shutdown input.

release the

14•

SHUTDOWN ZONE

Hood Brake Input

Flashes

4

Flashes

5

Remote Start

Manual transmission

7 Flashes

Tach

fails to start, the parking

last shutdown, turn the ignition

button.

Input

Valet

Mode

Transmission Mode not set

models only)

Crank Average not learned

not

learned

I

lights will flash one of

ON

(manual

Audiovox Electronics Corporation.

2012

27

N

(X)

BLUE

UNLOCK

(-)

GREEN

LOCK

(-)

BLACK/YELLOW

PULSE

DURING

CRANK

( - )

GREEN/WHITE

PULSE

AFTER

SHUTDOWN

( - )

LT

BLUE

FACTORY

ARM

I

PULSE

AFTER

START

( - )

L T GREEN/BLACK

FACTORY

DISARM

I

PULSE

BEFORE

START

( - )

D

BLACK

GROUND

WHITE/RED

PARKING

LIGHT

INPUT

WHITE

PARKING

LIGHT

OUTPUT

E~

GRAY/RED

PARKING

BRAKE

INPUT

(

- )

n:[ri

PURPLE

DOOR

INPUT (

+ )

GREEN

DOOR

INPUT

( - )

~~

BLACK/WHITE

ILLUMINATED

ENTRY

OUTPUT

( - )

BROWN/BLACK

HORN

OUTPUT

( - )

~~

RED/WHITE

TRUNK

RELEASE

OUTPUT

( - )

IU~

BLUE/BLACK

START

STATUS

I

ACTIVE

OUTPUT

( - )

PURPLE/WHITE

TACH

INPUT

o;:;

GRAY

HOOD

INPUT

( - )

0~

BROWN/RED

BRAKE

INPUT (

+ )

ull)

VIOLET/BLACK

AUX

1

OUTPUT

( - )

OBI

PORT

()9

:

ANTENNA

)

LED VALET

TELEMATIC

PORT

PURPLE

STARTER

OUTPUT-

MOTOR

SIDE

(

+ )

C")

~

RED

BATTERY

12V

(

+)

ORANGE

ACCESSORY

1 (

+ )

~

PINK/WHITE

IGNITION

2 (

+)

~

RED/WHITE

BATTERY

12V

(

+)

m

PINK

IGNITION

1 (

+ )

<

)>

2012 Audiovox Electronics

Corporation.

All

rights reserved. 29

30

ca5553sst

rev

A

2012 Audiovox Electronics Corporation.

All

rights

reserved.

31

Audiovox Electronics Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

FCC COMPLIANCE This device complies with Part 15 of the Industry Canada. Operation is subject to the

1.

This device may not cause harmful interference, and

2.

This device must accept any interference received, including any interference

that may cause undesired operation. Warning! Changes

or

modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

32

R41

0-192-540

FCC rules and with

following two conditions:

RSS-21 0

of

ca5553sst

rev

A

cccc:~L'.I~m

Deluxe

with

IMPORTANT NOTE:

applicable to most vehicles. However, due to the configuration of some vehicles, some functions

2012 Audiovox Electronics Corporation.

900Mhz

SAFETY

Vehicle

The operation of the Security and Convenience System as described in this manual is

PRECAUTIONS

Remote

Way

2

Remote

may not apply.

Confirming

Control

Please

see your

installing

Start

dealer for more information.

System

LCD

AND/OR

4280479

Table

Contents

of

Using

Your

Using the Keyless Two Stage Door Activating Trunk Activating AUX 1

Using the Progressive Car Finder Feature ...................................... 3

Using the Personal

Programmed Transmitter Notification .............................................. 4

Valet

Eliminating

Your

Remote Start Ready Mode ................................................................ 5

Cancelling

Remote

Mode ........................................................................................ 4

Lock

Remote

Remote Start Ready Mode ............................................. 5

Control

Entry ................................................................... 3

Unlock (optional)

Release (optional) ................................................ 3

(optional)

Protection

Unlock

I

Starter

............................................................... 3

................................................... 3

.............................................................. 3

Alarm

Notification Chirps ................................... 4

............................................... 3

................................................................

5

Remote Starting Your

Remote Start Shutdown ................................................................... 6

Entering Your Preheating or

User

Using the Quick Stop Feature .......................................................... 7

Operating the

Temperature Start Mode ................................................................... 8

Remote Start Safety Features ......................................................... 8

Additional

Programmable Run Time

2-Way LCD Remote LCD Remote Transmitter Replacing

Remote

Vehicle while

Precooling

Daily

Control

Button

Vehicle

Start Timer ........................................................ 7

ICON's

Functions

Control

.......................................................... 6

it is Running via Remote Start ........... 6

Vehicle's Interior ............................... 6

the

Run Time Extension ...................... 7

I

Control

Functions

........................

............................................................

......................................................... 12

Batteries

............................................. 13

9

11

Warranty

2

Information

......................................................................... 14

ca5553sst

rev

A

Using

y~

Remote

ur

,

Control

To

Entry

lock

or

the

unlock

vehicle's

doors, the

the doors simply

button is used to

riJ

press and

Using

The

the

button is used to lock

@

vehicle's

Keyless

doors. function button one time. For your convenience, the parking when the doors are unlocked

NOTE: The system is equipped with a feature system requires a second press of the unlocking third press of

Two

this feature is

If unlock only

response from the vehicle. If

unlock will activate the

Stage

Door

Unlock

enabled

on

the driver's door. Press

and twice when the door are

called Silent

button to activate

riJ

or

@

your system is set up for 2 step unlock,

audible

(Optional)

response.

your system, pressing the

again within three seconds to unlock the

ciJ

Choice. If enabled,

button one time

ciJ

remaining doors.

Activating

button is used to open the trunk of the vehicle.

The

ciJ

press and

Trunk

the

hold the

Release

button for 3 seconds.

ciJ

Feature

(Optional)

open the vehicle's

To

the

release

unlock

the desired

lights will flash once

locked.

the

audible locking/

an

will

trunk

a

(Optional)

Activating

this feature is

If

AUX

simultaneously will activate an for a wide range of functions like

installing dealer to determine the

consult

Using

Press the

your

Progressive

the

button to

cJ>))

and sound 5 times at

1

enabled

locate

low volume,

your system, pressing the

on

optional

feature. This feature can be programmed

power window or sunroof automation, please

functionality

Finder

Car

your vehicle.

Feature

The system

increasing

in

volume each time the button is

pressed.

Using

the

Press and

alarm.

During panic mode, the

Personal

the

hold

Protection

button for 3 seconds to activate the

cJ>))

suspended. The transmitter's door (if the option is

installed).

Alarm

normal function of the transmitter buttons

(iJ

and

@

stop the

To

(Panic)

buttons can be used to

alarm, the transmitter again for 3 seconds. The system seconds.

buttons

ciJ

and

@

of your system.

will flash the parking

personal

lock

press and hold the

will automatically

protection

will

unlock

and

button

cJ>))

stop after

lights

be

the on

30

Audiovox

2012

Electronics

Corporation.

All

rights

reserved.

3

Programmed

As

a security precaution each time the vehicle's ignition is turn

Transmitter

Notification

on

the status LED

light with flash the number of transmitters programmed into the system. This helps

to identify unauthorized transmitters from accessing your vehicle.

you believe

an

If

unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance.

Valet

Mode

Valet Mode is used to disable the system from remote starting.

valet mode simply follow the 4 steps outlined below:

1.

2.

3.

4.

Eliminating

System lock and unlock notification chirps can

Turn the vehicle's ignition ON.

Push and hold the programming/valet button.

The LED will turn

on

solid when valet mode is active

Release the programming/valet button.

Lock I Unlock

Notification

Chirps

be

toggled

ON

entering the programming feature banks.

1.

2.

Turn the ignition

ON

then

OFF.

Press and release the valet/programming button 3 times. The system

will respond with 1 chirp for

ON

or 2 chirps for

OFF.

To

enter or exit

or OFF without

4 ca5553sst

rev

A

Using Your Remote Starter

Remote with

Remote

To

activate the remote start function, the system must first

Ready Mode.

Start

a

manual

Start

1.

2.

Ready

Mode

must

be

transmission.

Ready

Follow While a. b.

the engine is running by the ignition key; Set the parking brake Place

Mode

the steps

-

Manual

below

the transmission

to enter remote start ready mode.

With your foot off the brake

enabled

if

Transmission

in

neutral.

pedal,

press and

times within 2 seconds. The LED will flash lights will turn on to confirm the system has entered quick stop mode.

3.

Remove the keys from the ignition, the

quick stop mode.

4.

5.

Exit the

vehicle and

close all vehicle

Within 1 minute of step

doors. The vehicle will

doors.

1,

press the

~

shutdown and sound 2 short chirps then 1

chirp to confirm ready mode is set.

your

vehicle

Vehicles

be

in

Remote Start

release

is

equipped

Only

the

0

3 times and the parking

vehicle will

button to lock

remain running

the

vehicle's

button 2

in

long

Cancelling

Remote

The system will

Open any door Open the hood or trunk (if connected)

Press the brake Release the parking brake

Turn

the ignition

Start

Ready

Mode

exit remote start ready mode if any of the following occur:

ON

2012 Audiovox

Electronics

Corporation.

All

rights reserved.

5

Remote

To

activate the remote start function, press and release the 0 button 2 times within

Starting

Your

Vehicle

2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle's parking lights will turn

on

(or flash depending

on

system settings) as a visual indication that the

vehicle has started and is running.

If your vehicle stalls or does not start, the system will pause 5 seconds, then try 2 more times to start the vehicle (a total of 3 attempts). The system will pause 5 seconds between each start attempt. If the vehicle does not start after the 3rd attempt, the system will abort the remote vehicle start process.

Note:

Do

not leave children or animals unattended

in

the vehicle when using the

remote start feature. Note: Manual transmission vehicles - Remote Start Ready Mode must

Remote

Start

Shutdown

Press and hold the 0 button for 3 seconds to turn the vehicle off.

Entering

1.

2.

3.

the

Vehicle

while

it

is

Running

via

Remote

Vehicle

Start

Unlock the vehicle's doors. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL! Insert the key into the ignition switch and turn to the ON or RUN

position.

4.

Press the brake pedal. The remote vehicle starter will disengage and

the vehicle will operate normally.

be

set.

Preheating

or

Precooling

Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle's interior to your setting.

6

the

Vehicle's

interior

ca5553sst

rev

A

User

Programmable

Run

Time I

Run

Time

Extension

The system has the ability to allow the user to extend the time the vehicle will

be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. If your system is set to run 15 minutes and the time remaining is 4 minutes, extending the run time will reset the countdown timer to 15 minutes and your vehicle will continue to run

for another 15 minutes. Follow the steps below to extend the vehicle's run time.

1.

2.

3.

The remote start must already be active.

Press and release the 0 button 4 times.

The system will chirp 1 time and flash the parking lights 4 times to confirm that the run time has been reset.

Using

the

"Quick-stop"

Feature -Automatic

Transmission

Vehicles

If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you.

To

engage

quick

stop:

1.

2.

Stop the vehicle and place the transmission

in

PARK.

With your foot off the brake pedal, press and release the 0 button 2 times within 2 seconds. The LED will flash 3 times to confirm quick stop is entered.

3.

Remove the keys from the ignition and exit the vehicle. Press the

@ button to lock the vehicle's doors if desired.

Note: Do not leave children or animals unattended

in

the vehicle when using the

quick-stop feature.

Operating

the

Daily

Start

Timer

The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote,

pressing both the

@ & 0 buttons together will activate the 24 hour countdown

timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the day, perform the following steps to complete the

process.

1.

2.

Turn the ignition ON/OFF (vehicle must

Within 10 seconds, while pressing the brake, press and release the 0 button twice.

3.

2012 Audiovox Electronics Corporation.

The vehicle will emit 2 chirps and flash the parking lights 4 times.

All

rights reserved.

be

disarmed).

7

Temperature

Start

Mode

The system has the

preset temperature threshold. Once activated, the system vehicle vehicle

one time based on the temperature setting and

is started with the key or remote started by the transmitter. Temperature is

read from the module, located below the dashboard

ability

to start the

vehicle

if the temperature drops

will only

will be

in

most instances, and the

cancelled if the

start the

vehicle's interior temperature may vary from the ambient temperature.

1.

2.

3.

Note: This feature is

Remote

For safety and security reasons, the system

vehicle

The

vehicle Press and release both the The

vehicle will

must be armed.

riJ

emit 1 chirp and

defaulted OFF and must

Start Safety

Features

starter from activating if any of the

&

0

buttons together.

flash the parking lights 1 time.

be

set

in

option programming.

will

shutdown or prevent the remote

following occur:

below

a

1.

2.

3.

4.

The

vehicle

The brake

hood is open.

pedal

is pressed prior to turning the

position. The engine is over-revved (tach checking Valet mode is active.

ignition key to the

only).

ON

8 ca5553sst

rev

A

Additional 2-Way LCD Remote Control Functions

Check

Press and

display

Display

Press and hold the

Vehicle

release

Status

[f

2 times then press

the current status of the

Illumination

[p

button for 1 second. The

vehicle.

seconds.

Melody

To

have the remote

a response from the

I

Vibration

Mode

control

vehicle

vibrate,

play a

press and release

seconds.

Button

To

toggle button beeps on or off press and

Beeps

seconds.

@

within 3 seconds, the transmitter

display will illuminate

melody

[f

release

tone or both each time it receives

then press and

[f

then press and

for 5

hold

ciJ

will

for 2

0

for 2

Battery

While incoming signals from the main unit until

display

press and

Clear

Press the

flashing

Button

Press and

on or off. When the button

Save

in

POWER SAVE

Mode

MODE

the 2-way LCD transmitter

a button is pressed. The LCD screen

SAVE to indicate that power save mode is

hold

Flashing

[f

[p

for 5 seconds.

Icons

and

Melody

Sound

button 3 times within 3 seconds. This

icons on the LCD screen.

Lock

release

[f

then press

hold the

lock

is active, the remote

@

for 2 seconds to

times when a button is pressed indicating it is

Illumination

ON.

will clear

locked.

will NOT look

To

enter power save mode

the

toggle

control will

for any

melody

sound and

the button

beep/vibrate 2

will

lock

Press and illumination

release

[p

2 times then press and

on or off. When on, the

sends a command.

2012

Audiovox

Electronics

Corporation.

All

rights

reserved.

hold

@

for 2 seconds to

display will illuminate

toggle

when it receives or

9

2

Car

Mode

control a second security system enter 2 car mode by pressing

To

icon appears on the transmitter's LCD

together for 3 seconds. When the

riJ

and screen it

will control

the second security system. Use the same method to exit 2

car mode and resume control

NOTE: learned

Parking

A second security system must be

to it before this feature

Meter

Countdown

of the

will

operate the

!Jil

original vehicle's

installed

and the LCD transmitter must

additional

security system.

system.

then press

~

@

be

The parking meter countdown timer has 6 preset times, to access the preset times

for 2 seconds,

and begin countdown press and

c:J>})

and

programmable

the

press of

Clock

each

additional

Adjusting

clock, alarm clock and

The

release

increase the countdown time.

will

Timer

Settings

the Function Menu. Press and hold [?for

then press and hold

[?

countdown timer are accessed through

3 seconds to access the function menu,

c:J>})

once you have accessed the feature menu press and release [?to scroll through each feature and

for 2 seconds to exit the menu.

hold

[?

follow the steps

below

to adjust the settings for each. Press and

Clock Clock Alarm Clock Alarm Clock Alarm Clock

Hour Minute

Hour

Minute

OFF

I

ON

Countdown Timer Hour

Press Press Press Press Press Press

Countdown Timer Minute Press

OFF Press

I

Countdown Timer

ON

to increase or

c:J>})

to increase or

c:J>})

to increase or

c:J>})

to increase or

c:J>})

to turn

c:J>})

to increase or

c:J>})

to increase or

c:J>})

to turn

c:J>})

ON

to decrease

0

to decrease

0

to decrease

0

0 to decrease

to turn

0

or

to decrease

0

to decrease

0

to turn

0

or

OFF

10

ca5553sst

rev

A

LCD·

Remote Control ICON's

~

LOCK

~

~«)1»~

6)

<looo~

~

~~

ii

TRUNK RELEASE

TRANSMITTING

ENGINE RUNNING

BATTERY INDICATOR

TIMER/TEMP START MODES

VIBRATE/SILENT MODE

~

~~

~«a~

:88:88

~ffi\~~

X

t

UNLOCK

VALET MODE

PANIC

TIME DISPLAY

BATTERY SAVE MODE

TIME COUNT DOWN

MELODY MODE

Iill

2 CAR MODE

~

ALARM CLOCK

11

Transmitter Button Functions

Press Unlock

+ Start

While

Armed

12

ca5553sst

rev A

Replacing Remote Control Batteries

1-Way Remote Control

The battery (model CR2032) inside each remote control should last approximately 1 year under normal use. When the battery becomes weak you will remote control range (the distance from the vehicle the remote control deteriorate and the

control batteries:

1.

2.

3.

4.

2 Way LCD Remote Control

Remove 3 screws and disassemble the halves of the remote control. Remove the old battery, observing the

and replace with a new CR2032 battery. Reassemble the halves of the remote control and

Test operation of the remote control.

The battery inside the 2 way LCD remote control supplied

battery charger to charge the battery until LCD screen shows 3 bars indicating charging is recommended that the battery

small

(part

# CATXMSS)

LED on the remote control

(part

#

CATXMLSS)

be

fully

charged before normal use.

will dim.

+1-

symbols

is

rechargeable, use the

the battery icon

complete. It

notice the

will

work)

To

replace the remote

on

the battery

install

the 3 screws.

on

is

the

13

CCCC~LI.I~m

Code Systems, Inc.

Code Systems Inc. ("CODE") warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the "Product"), purchased from provided below) should this Product under normal use and conditions, material or workmanship DURING THE LIFETIME OF THE VEHICLE NALLY INSTALLED, such defect(s) will for parts directly related to repairs of the defect(s).

Switches, indicator lights, and transmitter cases are similarly warranted to the original purchaser for a period of one (1) year from the date of purchase of the Product.

CODE accessories, sold separately, are covered by the applicable warranty accompanying the accessory.

This warranty is non-transferable, non-assignable and is voided when: (1) the Product is removed from the vehicle in which it was originally installed; or (2) the vehicle originally installed is transferred to another party.

This warranty does not apply to any product damaged by accident, physical or electrical abuse, improper installation, alteration, or use contrary to its intended function, fire, flood, or other natural acts.

be

Limited

repaired or replaced (at CODE's option) without charge

Lifetime

an

authorized CODE dealer, that (except as

Warranty

IN

in

be

proven defective

WHICH IT WAS ORIGI-

which the Product was

in

In

order for the Product to be repaired or replaced under the terms of this warranty, the defective Product must sales receipt. The date of purchase and year, make and model of the vehicle was originally installed must be clearly indicated on the sales receipt.

This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED OR

IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL

DURATION OF THIS WRITTEN WARRANTY. CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.

CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF CODE'S LIABILITY UNDER THIS WARRANTY MENT PROVIDED ABOVE CHASE PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION LABOR.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state

be

returned to

an

authorized CODE dealer and accompanied by a copy of the retail

in

which the Product

BE

LIMITED TO THE

IN

AND,

NO CASE SHALL CODE

IS

LIMITED TO THE REPAIR OR REPLACE-

IN

NO EVENT SHALL CODE'S LIABILITY EXCEED THE PUR-

BE

LIABLE FOR ANY

14

ca5553sst

rev

A

This product

is

covered

by

one or more

of

the

following

U.S.

Patents; Other

Patents

pending.

0407,034,0580,160,5,132.660, 5,157,375, 5,193,141, 5,349,931, 5,532,670.

5,357

,560,

5,534,845,

5,381

'128,

5~412,371,

5,467,070,

5.563,576, 5,563,600. 5,572,185. 5,602,535, 5,614,883, 5,617,819

5,245,694. 5,315,285,

5,469.141

t

5,469, 151, 5,506.568

5,334,969

5,646,591, 5,650,774, 5,656,868, 5,673,017, 5,656,997, 5,712,638, 5,783,988. 5,783,989 5,798,711. 5,805.056, 5,819,568, 5,828,316, 5,838,255, 5.850, 5,872,519, 5,898,391

t

5,900,806,. 5,905,4311 5,907, 195, 5,914,667, 5,945,936,

173. 5,850, 174, 5,855,050 5,952,933

5,990,786. 6,028,732, 6,028,505, 6,040,636, 6,043,734. 6,087,996, 6,093,979, 6,140,914 6, 184,779,

6,462,648,

6,218,740,

6,259,

169, 6,285,296, 6,288,635, 6,317,034, 6,452,483, 6,452,484

6,573,838, 6,697,719, 6,700,479, 6,781,507. 6,828,901, 6,982.631, 7,030,739 7,069, 127, 7.095,314, 7, 102,515, 7.135,962, 7,142,097, 7,191,053, 7,243,007, 7,248,150 7,332,998, 7,443,285, 7,463, 135, 7,483,783, 7,519,400, 7,532,959, 7,616,099, 7,646,285

7.653,463, 7,962;260

2012 Audiovox Electronics Corporation.

All

rights reserved.

15

Audiovox Electronics Corporation.

Customer Service

WWW. CODE-ALARM

FCC This device Industry Canada. Operation is subject to the following two conditions:

COMPLIANCE

complies

with Part 15 of the FCC rules

1-800-421-3209

.COM

and with RSS-21

0 of

1.

This device may not cause

2.

This device must accept any interference received,

that may cause undesired operation.

Warning!

Changes or modifications not expressly

compliance could

16

void the user's authority to operate the equipment.

harmful

R41

interference, and

including

approved by the party

0-192-550

any interference

responsible

for

ca5553sst rev A

WARNING

THIS VEHICLE IS EQUIPPED WITH

A

REMOTE

CONTROLLED

CAR

STARTER

BEFORE SERVICING THIS VEHICLE, REMOVE

THE MAIN

POWER FUSE

(RED WIRE) TO THE CAR STARTER

OR

DISCONNECT

THE

VEHICLE

BATTERY.

LBL0675