Code Alarm ca5154 professional Series Installation Manual

CCCc~LA~m

i=)r:lOFESSIONAI

SEr:liES

Automatic

I

Manual Transmission

Remote Start

Installation Guide

for

ca5154

with

Keyless

models:

Entry

4280605

Contents

Table

of

Before You Begin ......................................................................................... 3

Wire

Additional

Set Up

Connection

Pin Main Harness ................................................................................. 5

11

Parking Light Harness ...................................................................... 8

3 6 Pin 4 Pin

2

Start

Alternate Harness ........................................................................... 1

Door Lock Harness ........................................................................

Harness ................................................................................... 9

Ports

LED

Antenna OBI Telematic Interface

I

Port ................................................................................................... 15

Programming

&

Guide ............................................................................... 4

0

11

......................................................................................... 15

Programming Port ........................................................ 15

I

Port ........................................................................... 15

............................................................................. 16

Transmitter Programming ........................................................................ 16

Manual

Programming Feature Banks .................................................................. 17

Tach Smart Tach less

Feature Transmitter Remote Start System

Feature Programming ................................................................. 16

Programming ..................................................................................

Mode .............................................................................. 20

Descriptions

Button

Shutdown

Layout

...........................................................................................

.................................................................................

Functions

Diagnostics

.................................................................. 29

......................................................

20

21

30 31

2

ca5154

Install

rev A

BEFORE YOU BEGIN

PROFESSIONAL INSTALLATION

STRONGLY RECOMMENDED

Roll

down window to avoid locking keys

during installation

Avoid mounting components or routing wires near

in

vehicle

hot surfaces

Avoid mounting components or routing wires near moving parts

Tape or appearance

Use a circuits. DO NOT USE "COMPUTER SAFE PROBE" bags or damage

loom wires under hood for protection and

Digital Multi

Meter for testing and verifying

A

TEST LIGHT, OR

as these can set off air

vehicle

computers.

•

.

2014

Voxx

Electronics

Technical Support

orgoto

http://avxtech1.com

(800)

421-3209

3

z

<(

~

z

a..

"r" "r"

Pin Main Harness

11

GRAY/RED PURPLE DOOR INPUT GREEN BLACK/WHITE BROWN/BLACK

RED/WHITE TRUNK RELEASE BLUE/BLACK

( (-

INPUT

+)

)

PARKING

BRAKE

DOOR INPUT ILLUMINATED ENTRY

HORN

OUlPUT

( - )

OUTPUT

ACTIVE OUTPUT

START STATUS

I

- )

(

OUTPUT

- )

(

- )

(

- )

(

(/)

ZI-

-I

a..(!)

('t')-

_J

PURPLE/WHITE GRAY BROWN/RED VIOLET/BLACK AUX 1

TACH INPUT

HOOD PIN INPUT BRAKE

INPUT (

OUlPUT

3 Pin Parking Light Harness

BLACK WHITE/RED PARKING LIGHT INPUT WHITE PARKING LIGHT OUTPUT

GROUND

(

+ )

( - )

- )

6 Pin

Start

Harness

PURPLE

1-

0:::

<(

1-

(/)

z

a..

<.0

RED BATTERY 12V ( ORANGE

PINK/WHITE RED/WHITE PINK

4

STARTER

ACCESSORY IGNITION 2 (

OUTPUT-

1

+ )

BATTERY 12V (

+ )

(

IGNITION

1

MOTOR SIDE

+)

+ )

(

+)

ca5154 Install

rev A

4 Pin Alternate Harness

z~

-o

a..o

N.....J

1

BLACK/YELLOW GREEN/WHilE LTBLUE L T GREEN/BLACK

PULSE PULSE FACTORY FACTORY DISARM

2 Pin Door Lock Harness

BLUE

GREEN

11

Pin Main Harness

GRAY/RED

UNLOCK LOCK

PARKING

DURING

AFlER

ARM

(-)

CRANK

SHUIDOWN

I

PULSE

BRAKE

(-)

I

PULSE

INPUT

( - )

AFlER

BEFORE

(

- )

START

(-

)

(-

)

Locate the

vehicle's

Verification:

parking brake wire.

This wire

will register ground when the

vehicle's PARKING

BRAKE is engaged.

NOTE:

2

Locate the

The

following

connection is required for Manual Transmission Mode.

PURPLE

vehicle's

Verification:

dome

light

This wire

will register positive opened and the interior register ground

or

"0" Volts

DOOR TRIGGER INPUT

or

door pin switch wire.

voltage (POS)

light is on. This wire

when the door is

will

closed

(

+ )

when the

and the interior light

off.

Connect the PURPLE wire to the vehicle's positive door input wire(s).

NOTE:

Certain vehicles

may require

multiple connections. Refer to vehicle

application guide.

door

is

2014 Voxx Electronics

Corporation.

All

rights reserved.

5

3

GREEN

DOOR TRIGGER INPUT

Locate the vehicle's dome light or door pin switch wire.

register ground (NEG) when the door

Verification:

This wire

and the interior light

will

on. This wire

is

register positive voltage when the

will

door is closed and the interior light is off.

( - )

opened

is

Connect the GREEN wire to the

NOTE:

Certain vehicles may require

vehicle's

negative door input wire(s).

multiple

connections. Refer to

application guide.

4

BLACK/WHITE

This wire provides a ( - )

driving relays.

capable

of

200mA

ILLUMINATED

output for

seconds when the system is disarmed

30

Locate the vehicle's dome light or pin switch wire.

register positive voltage or ground when the

turned

ON.

HORN OUTPUT

5

Verification:

This wire will

vehicle's dome light

BROWN/BLACK

is

ENTRY

( - )

vehicle

OUTPUT

- )

(

Locate the vehicle's horn wire.

register at positive voltage and register

Verification:

This wire

will

ground when the horn switch is pressed.

Connect the

BROWN/BLACK

wire to the vehicle's horn wire. This is a

output, 200mA.

6

RED/WHITE

TRUNK RELEASE

OUTPUT

Locate the vehicle's trunk release wire at the trunk release switch.

Verification:

This wire will

register either positive voltage or ground when

the trunk release is activated.

option programming.

This is a

low current output, 200mA

and is configurable

in

(

- )

low

current

6

ca5154

Install

rev A

7

BLUE/BLACK

START STATUS

I

ACTIVE

OUTPUT (

- )

This wire provides a ground output when the remote start function is activated and remains for multiple application's a

until4

seconds after the remote start is shutdown.

1 amp diode is required in-line with the stripe facing the

If this wire

will

be used

control module.

8

Locate the vehicle's

1.

2.

3.

4.

5.

PURPLE/WHITE

ignition coil or

Verification:

Set voltmeter to

Test using the

AC VOLTS. Attach positive lead Attach negative Start

the engine.

lead

of

a volt meter to a constant 12-volt source.

of

a volt meter to the wire to be tested.

fuel

following procedure:

Have someone press on the gas

TACH INPUT

injector

pedal

slightly as you monitor the meter. If

connected to the correct wire, the voltage reading RPM increases.

Connect the PURPLE/WHITE

wire to the negative side

fuel injector.

9

GRAY

HOOD PIN INPUT

in

the engine compartment.

will

increase as the engine's

of

the

vehicle ignition coil or

( - )

Install a Hood Pin

for Remote

Verification:

Start.

Switch

This wire when connected will

vehicle's hood is opened.

Connect the GRAY wire to the hood pin.

NOTE:

10

Be sure to loom the wire, and seal the grommet.

BROWN/RED

Locate the vehicle's brake light wire at the brake pedal mounted switch. This

connection is required for Remote

Verification:

This wire registers positive voltage when the brake pedal

pressed.

Connect the BROWN/RED wire to the vehicle's brake light wire.

2014 Voxx Electronics

Corporation.

and connect to the GRAY wire. This connection is required

register ground when the

BRAKE

INPUT (

+ )

Start.

is

7

11

VIOLET/BLACK

AUX 1

This wire provides a

( - ) 200mA

output capable

driving relays. For Control

of

optional accessories (i.e. Power Window/Sunroof, etc.).

activate refer to the transmitter button configuration chart. Please refer to the

To

selectable options for timing.

3 Pin Parking Light Harness

1

Connect the self

BLACK

wire to a solid chassis ground point using a ring terminal and

tapping screw (not supplied). ensure a good connection. The recommended grounding point is a metal surface the driver's side kick panel

NOTE:

Do not ground the BLACK wire with any

area:

GROUND

Scrape away paint from the grounding point to

other vehicle components.

in

2 WHITE/RED

3

WHITE

PARKING LIGHT INPUT

PARKING LIGHT OUTPUT

Locate the parking light output wire at the

Verification: This wire registers positive

turned on.

Positive switching Parking Lights:

Connect the

WHITE/RED WHITE wire to

wire to a 15 Amp max fused battery source.

the parking light output wire.

Negative switching Parking Lights:

Connect the Connect the

WHITE/RED WHITE

wire to a good chassis ground.

wire to the parking

vehicle's light switch.

voltage when the parking lights are

output wire.

light

8

ca5154

Install

rev A

6 Pin Start Harness

1 PURPLE

STARTER OUTPUT ( + )

Locate the vehicle starter wire.

Verification: This wire registers voltage only when the key is turned to the

START position.

Verification: The starter wire registers voltage when the key is turned to the

START position.

Connect the PURPLE wire to the vehicle starter wire.

2 RED BATTERY 12V (

Locate 1

of

the vehicle's constant

12

Volt battery wires at the ignition switch. Verification: This wire will register ( + ) voltage switch.

+)

in

all positions of the ignition

12

Connect the RED wire to the constant

NOTE: Remove all fuses until all connections are made.

Volt battery wire.

3 ORANGE ACCESSORY 1 ( + )

Locate the vehicle's accessory wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to ACC

ON

(Accessory) and the key is turned to the START (or CRANK) position.

Connect the ORANGE wire to the vehicle's accessory wire.

Programmable output: IGN, ACC, Start.

4 PINK/WHITE

Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped).

(or RUN) position. The voltage drops out when the

IGNITION 2 (

+ )

Verification: This wire registers voltage when the key is turned to the ON (or RUN) position, but not the ACC (Accessory) position. The voltage does not drop out when the key

Connect the PINK/WHITE wire to the vehicle's ignition 2 wire.

Programmable output: IGN, ACC, Start.

is

turned to the START (or CRANK) position.

9

5 RED/WHITE

BATTERY 12V (

+)

Locate 1

of

the vehicle's constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage in all positions

switch.

Connect the RED/WHITE wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

6 PINK

IGNITION 1 (

+ )

Locate the vehicle's ignition wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position. The voltage does not drop out when the key is turned to the

START (or CRANK) position. Connect the PINK wire to the vehicle's Ignition wire. This wire is also used for Ignition 1 Output.

of

the ignition

4 Pin Alternate Harness

1 BLACK/YELLOW

Locate the vehicle's second starter (crank) wire at the ignition switch. (if equipped)

Verification: This wire registers voltage only

the ignition switch.

This wire will supply a ( - ) 200mA output and can be configured programming.

2

GREEN/WHITE

This wire will supply a ( - ) 200mA pulse after the remote start shuts down. This

is typically used to re-lock the vehicle's doors if they unlock upon remote start shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle's accessories from remaining

on

after remote start shutdown.

PULSE DURING CRANK ( - )

in

the start (crank) position

in

option

PULSE AFTER SHUTDOWN ( - )

of

This output is configurable

10

in

option programming.

ca5154 Install rev A

3

LT

BLUE

FACTORY

ARM

I

START ( - )

typically

used to

supply a

This wire

will

successful completion

PULSE

200mA

( - )

the remote start activation sequence and is

of

pulse both upon arming the system and upon

AFTER

re-lock the vehicle's doors upon remote start if necessary. This output is configurable in option programming.

4

L T GREEN/BLACK FACTORY DISARM

I

PULSE BEFORE START ( - )

This wire

will

supply a

(-)

200mA

pulse both upon disarming the system and when

the remote start feature is activated. Locate the factory perimeter alarm disarm wire

cylinder inside the drivers door.

from the

key

Verification:

This wire registers ground

the key is turned to the unlock

if

position in the driver's door cylinder.

This

output

is configurable in option programming.

Door Lock Harness

UNLOCK

LOCK

unlock outputs are designed to control several different types

I

(-)

of

1

2

The

2 Pin

BLUE

GREEN

lock

door

systems which may require additional parts. Please review the wire and location

vehicle. The most common

which type

chart to

see

types are shown

These

wires

supply a ( - )

door

of

the following

in

500mA

lock system is in

diagrams.

output.

your

2014 Voxx Electronics

Corporation.

All

rights reserved.

11

Negative

All

Door Lock and Unlock: Locate the lock

Switching

Locks

switch.

I

unlock wire at the vehicle's lock

I

unlock

Verification: These wires

will register ground when the Lock and Unlock

switches are activated.

Connect the GREEN and BLUE wires shown

Negative Locks:

GREEN ( - ) Lock Output

BLUE (

- )

Unlock Output

Positive

Switching

Locks

in

the diagram below.

Vehicle

Door Lock

Control Relays

All Door Lock and Unlock: Locate the lock

I

unlock wire at the vehicle's

switch.

Verification: These wires

will

register positive voltage when the Lock and

Unlock switches are activated.

Connect the GREEN and BLUE wires shown

Positive

Locks:

in

the diagram

below.

GREEN

( - ) Lock Output

lock

I

unlock

12

ca5154 Install

rev A

Reverse Polarity Locks (S-Wire Door

Door Lock and

All

Unlock:

Locate the

lock

switch.

rest at ground and register positive

Verification:

voltage

when the Lock and

These wires

will

Unlock

locks)

unlock

I

wire at

the

switches are activated.

vehicle's lock

unlock

I

Connect the GREEN and BLUE or BLUE/GREEN wires shown

supplied).

using (2) SPOT

Negative

Multiplexed

relays

(not

Reverse Polarity

Locks

Locks:

-e-----~

Cut

GREEN (

BLUE (

Output

) Lock

-

) Unlock Output

-

To Door Lock Motor

the diagram

in

below

All Door Lock and

Unlock:

Locate the lock

unlock

I

wire at

the

switch.

Verification:

This wire will

show

Please consult the wire and

variable ground when the switch is activated.

location

chart for specific resistor

your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown

supplied).

using (2) SPOT

Multiplex

relays

(not

Locks:

-----l~l-----+-

vehicle's lock

values

the diagram

in

Output

Unlock

)

(-

BLUE

unlock

I

for

below

2014 Voxx Electronics Corporation.

All

rights reserved.

13

Positive

All

Door Lock and Unlock: Locate the lock

Multiplexed Locks

switch.

I

unlock wire at the vehicle's lock

I

unlock

Verification:

This wire

will show variable positive voltage when the switch

is

activated. Please consult the wire and location chart for specific resistor values for your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2)

SPOT relays (not supplied).

Multiplex

Locks:

Adding Aftermarket Actuators

After installing aftermarket actuators, (not supplied). Connect the GREEN and BLUE wires shown

in

the diagram below using (2)

86

SPOT relays (not supplied).

BLUE ( - )

Unlock Output

14

ca5154 Install rev A

Additional Ports

Antenna

LED

I

Programming Port

I

the

a clear spot

Mount the supplied antenna/receiver

to

will not block the driver's vision. A good location

mount the antenna/receiver

near the rear view mirror. metallic

window film,

as

careful not

Be

this will

effect system range. Route the antenna/receiver

to

on

usually high on the windshield

is

cable to the control module and plug into the antenna port.

Data Bus

This 4 pin port

communicate with the

to

Interface

is

Flashlogic Door Lock and Transponder

available. Please refer to the

be

the tech service web site.

on

Tach

Input

Trunk/Hatch Open Diesel Glow Plug

Port

used for Flashlogic Door Lock and Transponder Databus

vehicle's

Databus. When using the

Interface modules the

(Data to Data) function list available per vehicle

020

Brake Safety

Shut

Down

Input

vehicle's

port to control the

OBI

following

windshield that

any

on

Interfaces

options may

Door Lock Control Passlock

Dome Light Supervision Transponder

Factory Alarm Arm

Telematic Interface

used for Telematic

This 4 pin port

which can control some

Pro,

is

Door Lock Control Trunk Release

Sliding Doors AUX

Car Find Remote

Port

Disarm Manual Arm

I

controls system)

Interface accessories, such as Car Connection

the following

of

features.

Output

Passkey

I

Interface

I

Start

Disarm

Interface

Activation

Inputs

Only)

(GM

(factory keyless

2014 Voxx

Electronics Corporation.

All

rights reserved.

15

Set

Up

&

Programming

Transmitter Programming - Feature Bank 1

1.

2.

3.

4.

5.

6.

NOTE: NOTE:

system.

NOTE:

transmitter

NOTE:

ignition is turned ON, system.

Turn the ignition

Press and

Within

Press 1 button The system Pressing the override button at anytime during programming

the next bank.

The system This system has 1 button programming which programs

The system

will

This system has

hold

10

seconds the system

will

erase the oldest transmitter

ON.

the valet/override button.

will

chirp (3) three times.

of

each transmitter you wish to program.

respond with 1 chirp for each accepted transmitter.

will advance to

will exit transmitter programming after 15 seconds of inactivity.

will hold

PTN

the LED

all channels

up

to

4 transmitters

in

- Programmed Transmitter Notification. Each time the will

flash the number

in

memory, programming a 5th

memory.

of

transmitters programmed

of

the

to

the

Manual

1.

2.

3.

4.

5.

6.

Defaulting

banks

Feature Programming - Feature Bank 2

Turn the ignition Press and Within Use the valet/override button to advance through each option bank. For

feature programming advance to Feature Bank four, (5) five, (6) six and (7) seven chirps.

Use the transmitter bank, the system

Press the transmitter flash indicating the changed feature.

will default all

ON.

hold

the valet/override button.

10

seconds the system will

0

will

chirp to match the feature number.

@

All

Features:

Pressing the

features and return you to feature bank 2

- 5

chirp (3) three times.

2,

3,

4 or

5,

which is (4)

button to scroll

button to change the desired feature. The LED

CJ

through the selections

button anytime while

in

each feature

in

any of the feature

- 4 chirps.

will

NOTE:

is on, there is no time

16

The system

will

limit.

remain

To

in

feature programming mode as

exit programming turn the

long

IGNITION

as

the ignition

OFF.

ca51541nstall

rev A

Feature Bank 1 - 3 Chirps Transmitter Programming

Refer to transmitter programming.

Factory Disann

Lt

Green

I

2

NOTE: On

2014 Voxx Electronics

Black

this

model

the

Corporation.

Lt

Green

All

Factory Disarm

I

2nd

Black

Output

wire

Bank

5

will

override

rights reserved.

Unlock

can be

Factory Disann Factory Disann Factory Disann

Start Status

configured

changes

made

350mS 500mS

in

Bank

3

or

Bank

in

Bank

3.

5.

Any

changes

to

this

feature

in

17

18

ca5154

Install

rev A

Feature 4

4 Black

NOTE:

Bank

5

this

•

Output

model

Alternate

I Yellow Output

On

7 Chirps

Control

the

Lt

Green

I

Black

Pulse Crank

Output

During

wire

will

Ground While Running

can be

override

configured

changes

Ignition

made

in

Bank

in

Bank

3

or

Bank

5.

Any

3.

changes

to

this

feature

in

Bank

5

2014

Voxx Electronics Corporation. All

rights reserved.

19

Tach Programming

The unit option

is

will not operate

turned

ON.

unless

an attempt is made to start the vehicle via the remote start

If without first programming tach, the unit tach has not been learned and stored. to the specific

vehicle, the unit may not realize that the

instances and reengage the starter motor.

learn the tach rate of most vehicle's single coil, multiple coil

will

unit

The Remote

packs, or single injector.

1.

2.

Start

learn tach:

To Turn the ignition key to the Press and release the valet/override button 3 times.

a tach

will

If

ON

the tachless

signal

programmed

is

or

flash the parking lights 7 times indicating

the tach rate is not properly programmed

certain

vehicle

is running

in

position.

3.

4.

5.

Immediately turn the ignition key Press and hold the valet/override button, then start the

key.

the When the unit senses the tach signal, the parking lights

OFF.

vehicle

begin to

will

using

flash. Allow the

6.

7.

Release the valet/program push-button switch. 1 long chirp and the

parking lights

vehicle

to settle to a normal idle speed.

for 2 seconds, indicating that the learned

will turn

on

tach signal is stored and the unit has exited tach learn mode.

improper tach connection or a

the unit fails to learn tach rate due to

NOTE:

If

poor tach source, the parking lights

not flash.

will

an

correct this situation, locate and

To

connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach learn routine.

Smart

Tach

less Mode

Smart

Tachless Mode is available only if a tach signal has never been learned to the

system and when activated

less without the need to enter the feature programming mode.

programming to

1.

Tach

Activate the remote start. The parking lights should begin flashing 7 times indicating no tach signal has been learned.

Within the 7 flash time period, press and hold the

2. The system

3.

mode.

20

will automatically

change the

Tach

Mode feature

button.

0

will chirp 1 time indicating the system is now

tachless

in

ca5154

option

in

Install rev A

Feature Descriptions

Feature

1 -

Silent

Bank

Choice:

ON

- Silent unlock system lock/unlock

OFF

a second time

will only sound the arm/disarm chirps upon a second press

-

normal arm/disarm chirps upon the first press

2-

arming/disarming upon first press

buttons.

2 - Passive Locks:

Active - Requires use of the transmitter to Passive -Automatically locks

is closed. Note: For Passive Locks, feature #3 Passive Arming must set to passive

3 - Passive

Arming:

Security

Controls

Determines

the

will

normal

arm/disarm chirps of the security system.

of

lock/unlock,

pressing

lock/

activate the arm/disarm chirps respectively. The

of

the

of

lock/unlock.

manual

the

or

automatic

vehicle's

locking

lock

the vehicle's doors.

of the

vehicle's

doors 1 minute after the

doors.

last door

also

manual

or automatic

locking

of the

vehicle's

doors.

be

Active - Requires use of the transmitter to arm the security system. Passive -Automatically arms the security system 1 minute after the

is

closed.

4 - 8

Not

available

9

-

OBI

Port

interface with

OBI

Protocol

ADS Protocol

10

-

Not

available

11

- L.E.D.

Output

locked.

ON

- LED will

on

this

model.

Protocol:

Determines the

external modules.

on

this

model.

when Armed:

flash when system is armed

protocol

Control

of

the LED

type

I

locked

in

which the

when

OBI

port uses to

the system

last

is

armed

door

I

OFFnormal

LED

will

not flash when system is armed

operation (armed/locked) and does not affect programming,

mode, diagnostics, passive

2014

Voxx Electronics

Corporation.

All

lock countdown or PTN.

rights reserved.

I

locked. Only applies

to

valet

21

Feature Bank 3 - Output

1 -Extended Lock

wires.

Pulse:

Controls the timing

Control

the BLUE and GREEN lock output

of

Second

1

Seconds

3.5

Second

1

second unlock pulse.

30 Second

second unlock pulse.

1

Double Pulse Lock, 1 second unlock pulse.

Factory Disarm:

2 -

output.

Factory Disarm - Single activation.

2nd Unlock Start Status - Single

during the remote start cycle.

Single

-

1 second lock pulse, single 1 second unlock pulse.

Single

3.5 second lock pulse, single 3.5 second unlock pulse.

Lock, Double Pulse Unlock -

Lock, Double Pulse

Second

Controls the timing

second pulse with unlock and remote start

1

Same

output as unlock with 2nd press

second pulse with unlock and continuous ( - ) output

1

Unlock-

the

of

Single

Single 30

1 second lock pulse, double 1

second lock pulse, double

Double 1 second lock pulse, single 1

GREEN/BLACK factory disarm

LT.

unlock.

of

Factory Disarm - Single 350mS

activation.

Factory Disarm - Single 500mS

activation.

NOTE:

or Bank

3.

3 - Ignition

or

On

5.

OFF.

OFFLock and

ignition is turned off. Lock Unlock Only Doors unlock when ignition

second pulse with unlock and remote start

Black

this model the Lt Green

I

Any changes to this feature

Controlled

Locks:

Control of door locks when the ignition is cycled

Output

Bank 5

in

Door locks not activated by ignition.

Unlock-

- Doors lock when ignition

Only

Doors lock when ignition is turned on and unlock when

wire can be configured

will override changes made

turned on only.

is

turned off only.

is

Bank 3

in

Bank

ON

22

ca5154

Install

rev A

4 - Trunk Output Timing - Red/White Output: Controls the output timing/type RED/WHITE output.

1 Second Pulse - 1 second pulse output.

10 Second - Continuous output for 10 seconds. 20 Seconds - Continuous output for 20 seconds. Latched until IGN ON - Continuous output until the vehicle's ignition is turned

ON.

ON

Latched is

pressed again.

5-

Horn Output Timing: Control the minimum horn pulse time

until Button

Press-

Continuous output until the activation button

in

milliseconds,

some vehicle will require a longer pulse to activate the factory horn.

of

the

16mS 1

OmS

30mS 40mS 50mS

6 - Real Panic: Controls the panic out when triggered from the transmitter.

ON

OFF - Standard pattern horn honks when panic

7 - AUX

1 Second

Latched-

Latched untiiiGN

Dome Light

by the AUX 1 function

- Randomized horn honks when panic

1:

Controls the VIOLET/BLACK AUX 1 output activation type and timing.

Pulse-

Single 1 second pulse.

Output stays active until button

ON-

Output-

Output stays active until the ignition is turned on.

Output used for illuminated entry and

of

the transmitter.

is

triggered.

is

triggered.

is

pressed again.

is

not controlled

Defrost Output Single Pulse - Single 1 second pulse after start Defrost Output Latched 5

Minutes-

5 minute continuous output after

remote start.

Feature Bank 4 - Remote Start Control

1 - RF Start Chirp: Turns remote start activation confirmation chirps ON or

2 - Run Time: Controls the time

control down at any time by use

of

the remote start until the system times out. The system may also be shut

in

minutes that the vehicle will stay running under

of

the transmitter or system shutdowns.

OFF.

23

3 - Running Lights: Controls the WHITE parking light output wire during remote start.

Steady-

Parking lights constant during the remote start cycle.

Flashing - Parking lights flash at a slow pace during the remote start cycle.

4 - Tach Mode: Determines how the system monitors the engine running during remote start.

Tach

- Hard wired directly to the tach wire

of

the vehicle to monitor AC

voltage. Tach

less (Crank AverageNoltage)- Determines crank time by averaging the last 8 times the vehicle was started with the key and then monitors the change

Hybrid (Crank Average the last 8 times the vehicle was started with the

OBI connected to the

in

Port-

voltage after remote start.

I No Voltage) - Determines crank time by averaging

key.

Monitors the vehicle's tach rate through an interface module

OBI

port.

5 -Voltage Level: The voltage variance for remote start when set to tachless. (see tach mode)

HIGHis

activated to after the engine is running must

The variance

LOW - The variance is

activated to after the engine is running may

6

-Crank

Time: Preset output times for the PURPLE starter wire.

1 Second 0.8 Seconds 1.5 Seconds 2 Seconds 4 Seconds

7 - Crank Average

I Crank Time: The length of time

crank the vehicle's starter.

Crank Average - Determines crank time by averaging the last 8 times the vehicle was started with the

Preset

Time-

Preset starter output time. (see crank time)

in

battery voltage from before the remote start

be

greater than 0.5 volts.

in

battery voltage from before the remote start

be

less than 0.5 volts.

in

which the remote start will

key.

24

ca51541nstall rev A

8-

Gas

Diesel:

I

Selects

remote start activation.

engine type and

delay

time for the starter output wire during

Gas-

10 Second Delay -

seconds after the ignition has been powered up by the remote start.

Second Delay

15 seconds after the ignition has been powered up by the remote start.

20 Second Delay seconds after the ignition has been powered up by the remote start.

45 seconds after the ignition has been powered up by the remote start.

9 - Single

double

IGN

-

or

single

10

Ignition 2 Accessory

Gasoline

engine, no

Diesel

- Diesel

Second Delay

Double Pulse Start:

I

- Diesel engine,

press from the transmitter.

2 Output:

Programmable high current output.

Ignition

-

output during remote start.

-Accessory

delay

engine,

for the starter output wire.

delays

the starter output wire for

the starter output wire for 15

the starter output wire for

the starter output wire for 45

Switches the remote start activation between a

output during remote start.

10

20

Crank

I

Start

- 2 or 3 Hour Start:

11

12 - Turbo Timer:

- Crank output during remote start.

Not available

Not available on this model.

13 -Transmission Mode:

vehicle's

transmission type.

Automatic - For use with automatic transmission vehicles.

start operation. Manual

- For use with

must be set upon exit

14 -Temperature Start:

on this model.

Select

the type

manual transmission

enable

vehicle

of

Not available

to

on

remote start activation based on the

of

Standard remote

vehicles.

Remote start ready mode

remote start.

this model.

2014 Voxx

Electronics Corporation.

All

rights reserved.

25

15 -Accessory

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Output:

Programmable high current output.

Ignition

- Output becomes active with the

and does not drop out during crank. Start

I

Crank - Output becomes active with the same timing as the starter

output wire, during crank

16-

Pulse Additional Outputs

only.

w/

the remote transmitter the system

Ignition,

also

Accessory & Ground

activates the

OFF

-When

IGN, ACCY,

pulse

Unlock is pressed no

GWR-

simultaneously pulse

While Running outputs for 1 second. The 3rd setting

after shutdown output to turn off the RAP on certain

When the Unlock button is pressed the system

the

Ignition,

for 1 second. IGN, ACCY,

pressed the system Ground the green/white

GWR, then

Pulse After Shutdown - When the

will also simultaneously pulse

while Running outputs for 1 second then waits 2 seconds then pulses

pulse

after shutdown wire

Unlock:

same

When the

timing as the ignition output

Unlock

button is pressed on

will also simultaneously pulse additional outputs.

vehicles

additional

outputs are activated.

will also

Accessory & Ground

for

1 second.

while Running outputs

the

Unlock

Ignition,

button is

Accessory

&

17 - Door Lock Control During Remote Start:

outputs during the remote start sequence.

OFF

- The system

Unlock

before

sequence begins, Lock

will

Start,

not

lock

Lock After

pulse

after remote start sequence is

or

unlock

Start

- Unlock Pulse

engine is running. Unlock Before Lock After Start

Start - Unlock Pulse before remote start sequence begins.

- Lock

pulse

after remote start sequence is

engine is running. Lock After

Shutdown

- Lock

pulse

after remote start shutdown sequence is

complete

Controls the systems door

the

vehicle.

before remote start

complete

lock

and

26

ca5154

Install

rev A

Feature Bank 5 - 4 Pin

1 - Lt

and timing.

Green/Black Output

Pulse before activated. Also a 1 second pulse when unlock is pressed.

Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.

Start

Alternate Output

Controls the L T GREEN/BLACK output activation type

:

During Unlock - 1 second pulse when remote start is

I

Control

2 - Lt

Ignition -

Output

becomes active with the same timing as the ignition output

and does not drop out during crank. Accessory - Output

becomes active with the same timing as the accessory

output, drops out during crank. Pulse During Crank -

Output

becomes active with the same timing as the

starter output wire, during crank only.

BLUE output activation type and timing.

Controls the

Blue Output

Pulse After

:

Start

During

I

sequence and has confirmed the

pressed.

when lock

is

LT

Lock-

1 second pulse after the remote start

running. Also a 1 second pulse

vehicle

is

Ground While Running - Continuous output for the entire remote start

sequence until after the vehicle shuts down.

Ignition

Output

-

becomes active with the same timing as the ignition output

and does not drop out during crank.

Accessory-

Output

becomes active with the same timing as the accessory

output, drops out during crank.

Pulse During Crank - Output starter output wire, during crank only.

Green/White

-

3

Output :

timing.

Pulse After Shutdown - 2 second pulse after the remote start has shutdown.

Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.

Ignition - Output becomes active with the same timing as the ignition output

and does not drop out during crank.

Accessory - Output output, drops out during crank.

Pulse During Crank - Output starter output wire, during crank only.

2014 Voxx Electronics Corporation.

becomes active with the same timing as the

Controls the GREEN/WHITE output activation type and

becomes active with the same timing as the accessory

becomes active with the same timing as the

27

4 -

Black/Yellow

timing.

Output : Controls the BLACK/YELLOW output activation type and

Pulse During

Crank

- Output becomes active with the same timing as the

starter output wire, during crank only.

Ground While Running - Continuous output for the entire remote start

sequence until after the vehicle shuts down.

Ignition-

Output becomes active with the same timing as the ignition output

and does not drop out during crank. Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank.

28

ca5154

Install

rev A

Transmitter Button Functions

Way

1 Transmitter

Lock

Unlock

Car

Find

Panic

I

Start

N/A

Operation

Method

Press

Unlock

Start While

+

Anned

Electronics

Voxx

2014

Corporation. All

rights reserved.

29

Remote Start Shutdown Diagnostics

If

the remote start shuts down or

patterns

To

manually

press and release the

below

LED

indicating the shutdown input.

enter diagnostics and view the

14•

FLASHES

SHUTDOWN ZONE

fails

button.

to start, the parking

lights will

last

shutdown, turn the ignition

flash one

ON

of

the

and

3 Flashes

4 Flashes

5 Flashes

7 Flashes

Hood Brake

Remote

Input

Start

Valet Mode

Manual Transmission Mode not set (manual transmission models

Tach

not learned

only)

I

Crank Average not

learned

30

ca5154

Install

rev A

N

0

......

.::...

a-

#4120106

BLUE

UNLOCK

(-)

~

GREEN

LOCK

(-)

m

co

(')

-

...,

0

:::J

BLACK/YELLOW

PULSE DURING

CRANK ( - )

c:;·

CJ)

#4120102

GREEN/WHITE

PULSE

AFTER

SHUTDOWN

( - )

()

LT

BLUE

FACTORY

ARM

I

PULSE

AFTER

START

( -

)

0

...,

L T GREEN/BLACK

FACTORY DISARM

I

PULSE

BEFORE

START

(-

)

"0

0

...,

~

a·

?

#4120103

D

BLACK

GROUND

~

WHITE/RED

PARKING LIGHT INPUT

...,

WHITE

PARKING LIGHT OUTPUT

c6"

::r

u;

...,

ro

E~

N

GRAY/RED

PARKING

BRAKE

INPUT

(-

)

CJ)

M

ro

1.1"1

PURPLE

DOOR INPUT

(

+ )

<

n:~

0

\0

GREEN

DOOR INPUT

(

- )

ro

M

p..

3()

'<t

BLACK/WHITE

ILLUMINATED ENTRY OUTPUT

( - )

'**'

#4120185

BROWN/BLACK

HORN OUTPUT

(

-

)

~

RED/WHITE

TRUNK RELEASE

OUTPUT (

-

)

IU

BLUE/BLACK

START STATUS

I

ACTIVE OUTPUT

(

- )

PURPLE/WHITE

TACH

INPUT

0

GRAY

HOOD INPUT

(

-

)

0

BROWN/RED

BRAKE

INPUT (

+ )

u

VIOLET/BLACK

AUX 1

OUTPUT (

-

)

OBI

PORT

#4120291

ANTENNA

(o

#41~54

)

LED VALET

TELEMATIC PORT

PURPLE

STARTER

OUTPUT - MOTOR SIDE

(

+ )

RED

BATTERY 12V (

+ )

#4120110

ORANGE

ACCESSORY

1 ( + )

PINK/WHITE

IGNITION

2

(

+ )

RED/WHITE

BATTERY 12V (

+)

PINK

IGNITION

1

(

+ )

w

......

Voxx

Electronics

Corporation.

FCC This device

COMPLIANCE

Customer Service

complies

1-800-421-3209

WWW.CODE-ALARM.COM

with Part 15

of

the

FCC rules and with RSS-21 0

of

Industry

1.

This device may not cause harmful interference, and

2.

This device must accept any interference received,

Canada. Operation is subject to the

may cause undesired operation.

Warning!

Changes or modifications not compliance could

void the user's authority to operate the equipment.

PATENTED: www.voxxintl.com/company/patents

32

expressly

R410-192-730

following two conditions:

including any interference that

approved by the party

responsible

ca5154

for

Install

rev A

CCJCc~~~m

Automatic I

Remote

IMPORTANT

applicable

2014

Vox:x.

Electronics

NOTE: The operation

to most

SAFETY

Corporation. All

Start

vehicles.

PRECAUTIONS

Manual Transmission

and

of

the Security and Convenience System as described

However, due to the configuration

may not

rights reserved.

Keyless Entry System

apply. Please

see your installing dealer

of

some

vehicles,

in

this

manual

some functions AND/OR

for more information.

4280606

is

Table

Using Your Remote Control .................................................................... 3

Using the Keyless Entry .................................................................... 3

Two Stage Door Unlock (optional) ..................................................... 3

Activating Trunk Release (optional) ................................................... 3

Activating AUX 1 (optional) ................................................................ 3

Using the Progressive Car Finder Feature ........................................ 3

Using the Personal Protection Alarm ................................................. 3

Programmed Transmitter Notification ................................................ 4

Valet Mode ........................................................................................ 4

Eliminating Lock

Using Your Remote Starter ..................................................................... 5

of

Contents

I Unlock Notification Chirps .................................... 4

Remote Start Ready Mode ................................................................ 5

Cancelling Remote Start Ready Mode .............................................. 5

Remote Starting Your Vehicle ............................................................ 6

Remote Start Shutdown .................................................................... 6

Entering Your Vehicle while it is Running via Remote Start .............. 6

Preheating

User Programmable Run Time

Using the Quick Stop Feature ........................................................... 7

Operating the Daily Start Timer ......................................................... 7

Remote Start Safety Features ........................................................... 8

Transmitter Button Functions ................................................................ 8

Replacing Remote Control Batteries ..................................................... 9

Warranty Information ............................................................................ 10

or

Precooling the Vehicle's Interior ................................. 6

I Run Time Extension ....................... 7

2

ca5154 Owners rev A

Using

Using the Keyless Entry

Your

Remote Control

button is used to

vehicle's

button is used to lock

@

The

lock or

vehicle's function button one time. For your convenience, the parking the doors are

NOTE:

system requires a second press unlocking press

Two

this feature is enabled

If only doors.

Activating the Trunk Release Feature (Optional)

The

press and

doors.

The system is equipped with a feature

response from the

unlock will

of

Stage

the driver's door. Press

button is used to open the trunk

co

hold

To

unlocked

Door

Unlock (Optional)

the

and twice when the door are

activate the audible

button for 3 seconds.

co

the

unlock

your system, pressing the

on

the doors simply

the

of

vehicle. If your system is set up for 2 step

again within three seconds to

co

doors, the

called Silent

co

or

@

response.

the vehicle.

of

button to activate an

co

press and

locked.

button one time

co

To

unlock

release the desired

lights will

Choice. If enabled,

unlock

open the vehicle's

flash once when

audible locking/

unlock,

will unlock

the remaining

the

a third

trunk

Activating

this feature is

If

simultaneously will

wide range

installing dealer

Using the Progressive Car Finder Feature

Press the

and sound 5 times at

pressed.

Using the Personal Protection Alarm (Panic)

Press and During panic mode, the normal The transmitter's option is installed). again for 3 seconds. The system

AUX

c::J

hold

1 (Optional)

enabled

activate

functions

of

to determine the

button to

)})

low volume,

>})

c::J

the

and

@

stop the

To

your system, pressing the

on

optional feature. This feature can be programmed for a

an

power window or sunroof automation,

like

functionality

locate

button for 3 seconds to activate the

your vehicle.

increasing

function

buttons can be used to

ciJ

alarm,

will automatically

of

press and

of

The system

in

the transmitter buttons

and

@

your system.

will flash

volume

hold

each time the button

and

lock

c::J

the

stop after

buttons

co

please consult

the parking

personal

will

unlock button

)})

30 seconds.

your

lights

is

protection

be suspended.

the door (if the

the transmitter

on

alarm.

Voxx Electronics

2014

Corporation.

3

Programmed Transmitter Notification

As a security precaution each time the vehicle's light

with

flash

the number of transmitters programmed into the system. This

to identify unauthorized transmitters from accessing your

ignition

is

turn

on

vehicle. If

the status LED

helps

you

believe

an

unauthorized transmitter has been programmed to your system, contact your installing dealer

Valet Mode

Valet Mode mode

Eliminating Lock

for assistance.

is

used to disable

the system from remote starting.

simply follow the 4 steps outlined below:

1.

2.

3.

4.

Turn the Push and The LED Release

vehicle's ignition ON.

hold

the programming/valet button.

will

turn on

solid

when

the programming/valet button.

I

Unlock Notification Chirps

valet

mode

is

active

To

enter or exit valet

System

lock

and

unlock

notification chirps can

entering the programming feature banks.

1.

2.

Turn the ignition

Press and release

will respond with 1 chirp for

ON

then

OFF.

the valet/programming button 3

ON

be

toggled

or 2 chirps for

ON

or OFF

without

times. The system

OFF.

4 ca5154

Owners rev A

Using Your Remote Starter

Remote Start Ready Mode must be enabled manual transmission.

your vehicle

if

equipped with a

is

Remote Start Ready Mode - Manual Transmission Vehicles

in

activate the remote start function, the system must first

To Mode. Follow

1.

2.

3.

the steps While a. b.

Set Place

With your foot off the brake pedal, times within 2 seconds. The LED

lights will Remove the keys from the ignition, the

below to enter remote start ready mode.

running by the ignition key;

the engine

is

the parking brake

neutral.

the transmission

in

press and release

flash 3 times and the parking

will

to confirm the system has entered quick stop mode.

on

turn

vehicle will

be

quick stop mode.

4.

5.

Exit the vehicle and

close all vehicle

Within 1 minute of step

press the

1,

doors.

button to

liJ

doors. The vehicle will shutdown and sound 2 short chirps then 1 long

set.

chirp to confirm ready mode

is

Only

Remote

the

Start Ready

button 2

0

remain running

vehicle's

the

lock

in

Cancelling Remote Start Ready Mode

exit remote start ready mode if any of the Open Open

will

any door the hood or trunk (if connected)

The system

Press the brake Release

Turn the ignition

the parking brake

ON

following occur:

2014 Voxx Electronics

Corporation.

All

rights reserved.

5

Remote Starting Your Vehicle

To

activate the remote start function, press and release the 0 button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it

is

safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle's parking lights will turn on (or flash depending

on

system settings) as a visual indication that the vehicle has started and

is

running. If your vehicle stalls or does not start, the system will pause 5 seconds, then try

2 more times to start the vehicle

(a

total

of

3 attempts). The system will pause 5 seconds between each start attempt. If the vehicle does not start after the 3rd attempt, the system will abort the remote vehicle start process.

Note:

Do

not leave children or animals unattended

in

the vehicle when using the

remote start feature.

Note: Manual transmission vehicles- Remote Start Ready Mode must be set.

Remote Start Shutdown

Press and hold the 0 button for 3 seconds to turn the vehicle off.

Entering the Vehicle while it is Running via Remote Vehicle Start

1.

2.

3.

Unlock the vehicle's doors. Enter the vehicle.

DO

NOT PRESS THE BRAKE PEDAL!

Insert the key into the ignition switch and turn to the

ON

or RUN

position.

4.

Press the brake pedal. The remote vehicle starter will disengage and

the vehicle will operate normally.

Preheating

or

Precooling the Vehicle's interior

Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle's interior to your setting.

6

ca5154 Owners rev A

User Programmable Run Time I Run Time Extension

The system has the ability to allow the user to extend the time the vehicle will running under control of the remote start. This will only extend the

run

time back to the

current run time setting during the current remote start cycle. If your system

is

run 15 minutes and the time remaining

4 minutes, extending the

the countdown timer to 15 minutes and your vehicle will continue to

run

time will reset

run

for another 15

be

is

set to

minutes. Follow the steps below to extend the vehicle's run time.

be

1 . The remote start must already

2.

3.

Using the "Quick-stop" Feature -Automatic Transmission Vehicles

Press and release the 0 button 4 times.

The system will chirp 1 time and flash the parking lights 4 times to

run

confirm that the

time has been reset.

active.

If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you.

To

engage quick stop:

1.

2.

Stop the vehicle and place the transmission

in

PARK.

With your foot off the brake pedal, press and release the 0 button 2 times within 2 seconds. The LED will flash 3 times to confirm quick

is

entered.

(I)

3.

stop Remove the keys from the ignition and exit the vehicle. Press the

button to lock the vehicle's doors if desired.

Note: Do not leave children or animals unattended

in

the vehicle when using the

quick-stop feature.

Operating the Daily Start Timer

The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, while

(I)

of the vehicle, pressing both the

& 0 buttons together will activate the 24 hour

in

range

countdown timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the

day,

perform the following steps to complete the

process.

1.

2.

Turn the ignition ON/OFF (vehicle must Within 10 seconds, while pressing the brake, press and release the 0

button twice.

3.

The vehicle will emit 2 chirps and flash the parking lights 4 times.

be

disarmed).

7

Remote

Start

Safety Features

For safety and security reasons, the system will shutdown or prevent the remote vehicle starter from activating if any

of

the following occur:

1.

2.

The vehicle hood is open. The brake pedal

is

pressed prior to turning the ignition key to the ON

position.

3.

4.

The engine

is

over-revved (tach checking only).

Valet mode is active.

Transmitter Button Functions

1

Way

Transmitter

Lock

Unlock

Car

Find

Panic

I

Start

Operation

Method

AUX 1

8

X

Push and Hold

(3

Sec)

ca5154 Owners rev A

Replacing Remote Control Batteries

1 Way 4 Button Remote

The batteries inside each remote

Control-

Model CAT4

control should last approximately

use. When the batteries become weak you distance from the the remote

control will

1.

vehicle

the remote

dim.

Using a coin,

control will work) deteriorate and the

To

replace

disassemble

the remote

control.

2.

3.

4. Test operation

Remove the batteries and

old

replace

Reassemble the

of

battery, observing the +/-

with a new battery.

halves

of

the remote

will

the

halves

control.

notice the remote

control

batteries:

of

the remote

symbols

control

1 year under

control

range (the

small LED on

on the

normal

2014

Voxx Electronics Corporation.

All

rights reserved.

9

Code Systems,

Inc.

Limited

Lifetime Warranty

Code Systems product (the

"Product"),

Inc. ("CODE")

purchased from an authorized CODE

warrants to the ORIGINAL

PURCHASER

dealer, that (except as provided below)

of

should this Product under normal use and conditions, be proven defective

WHICH IT WAS ORIGINALLY INSTALLED,

DURING defect(s)

LIFETIME OF

THE

be repaired

will

THE

replaced (at

or

VEHICLE

IN

CODE's

option) without charge for parts directly related to

CODE vehicle

this

material

in

or

security

workmanship

such

repairs of the defect(s).

Switches, indicator lights, and transmitter cases are a period of one (1) year from the date of purchase

CODE

accessories,

sold separately, are covered by the applicable warranty accompanying the

similarly

the Product.

of

warranted to the original purchaser for

accessory.

voided when: (1) the Product is removed from

This warranty the vehicle

in

non-transferable, non-assignable and

is

which it was originally installed;

or (2) the

is

vehicle

which the Product was

in

originally

installed is transferred to another party.

This warranty does not apply to any product damaged by accident, physical or electrical abuse, im-

proper

In Product must be returned to an authorized sales receipt. The date

was

installation, alteration, or use contrary to its intended function, fire,

order for the Product to be repaired or replaced under the terms

CODE dealer and accompanied by a copy

purchase and year, make and model of the vehicle

of

originally installed

must be

clearly

indicated on the sales receipt.

flood,

this warranty, the defective

of

or other natural acts.

the retail

of

which the

in

Produ~t

CODE MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED.

exclusive

This warranty

is ANY IMPLIED WARRANTIES, INCLUDING AND FITNESS WRITTEN

INCIDENTAL

FORA

WARRANTY.

DAMAGES

and

IMPLIED

ANY

PARTICULAR PURPOSE, SHALL

NO CASE SHALL CODE

IN

BREACH OF THIS OR

FOR

BE

WARRANTY LIMITED TO THE

BE

LIABLE FOR

OTHER

ANY

OF MERCHANTABILITY

DURATION OF THIS

CONSEQUENTIAL OR

ANY

WARRANTY,

EXPRESS OR

IMPLIED, WHATSOEVER.

CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT

REPAIR OR REPLACEMENT

CODE'S LIABILITY

PROVIDED ABOVE PRICE PAID BY

THE

UNDER

AND,

ORIGINAL

THIS

IN

WARRANTY EVENT SHALL CODE'S LIABILITY

NO

IS LIMITED TO

PURCHASER OF THE

THE

EXCEED THE

PURCHASE

PRODUCT WITHOUT INSTALLATION

LABOR.

incidental or consequential damages, so the

Some

states do not

the exclusion

allow

or limitation

above limitation may not apply to you. This warranty gives you specific

of

rights and you may also

legal

have other rights which vary from state to state.

OF

10

ca5154

Owners

rev A

11

Voxx Electronics Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

FCC COMPLIANCE

of

This device complies with Part 15

Industry Canada. Operation is subject to the following two conditions:

1.

This device may not cause harmful interference, and

2.

This device must accept any interference received, including any interference that

may cause undesired operation.

the FCC rules and with RSS-21 0

Warning!

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

PATENTED: www.voxxintl.com/company/patents

12

of

ca5154 Owners rev A

WARNING

THIS

VEHICLE IS EQUIPPED WITH

A REMOTE

CONTROLLED

CAR STARTER

BEFORE

SERVICING THIS VEHICLE, REMOVE THE MAIN

POWER

FUSE (RED

WIRE) TO

THE

CAR STARTER

OR

DISCONNECT

THE

VEHICLE

BATTERY.

LBL0675