Code Alarm ca5153, ca5153sst Installation Manual

cc

r:»~OFESSIONAI

c

c:

SE~IES

W-~1./.1

~

m

Automatic

Remote Start

Installation Guide

I Manual Transmission

for

ca5153

ca5153sst

with

models:

Keyless Entry

2012 Audiovox Electronics Corporation.

All

rights reserved. 4280476

Table

Contents

of

Before Wire

11

3 Pin Parking Light Harness ..................................................................... 8

6 Pin Start Harness ................................................................................... 9

4 Pin Alternate Harness .......................................................................... 1

2 Pin Door Lock Harness ........................................................................

You

Connection

Pin Main Harness ................................................................................. 5

Additional

Antenna

Port .................................................................................................... 15

OBI

Telematic Interface Port .......................................................................... 15

Begin

Ports

LED

I

...................................................................................... 3

Guide

...........................................................................

...................................................................................... 15

Programming Port ....................................................... 15

I

4

0

11

Programming

&

Up

Set

Transmitter Programming ........................................................................ 16

Manual

Programming Feature Banks .................................................................. 17

Tach Programming .................................................................................. 19

Smart

Feature

Transmitter

Remote

System

Feature Programming ................................................................. 16

Tach less Mode ............................................................................. 19

Descriptions

Button

Start

Layout

Shutdown

......................................................................................... 28

.......................................................................... 16

.............................................................................

Functions

Diagnostics

............................................................. 26

................................................ 27

20

2

ca5153/5153sst rev A

BEFORE YOU BEGIN

PROFESSIONAL INSTALLATION

STRONGLY RECOMMENDED

Roll

down window to avoid locking

during

Avoid mounting components or routing wires near

installation

keys

in

vehicle

hot surfaces

Avoid mounting components or routing wires near

moving parts

Use a Digital Multi circuits. "COMPUTER SAFE PROBE" bags or damage

DO NOT USE

Meter for testing and verifying

A TEST LIGHT, OR

as

these can set off air

vehicle

computers.

•

.

. .

2012

Audiovox Electronics Corporation.

Technical

http://techservices.codesystems.com

Support

or

go

to

(SOO)

421-3209

3

Pin Main Harness

11

GRAY/RED PURPLE

PARKING DOOR INPUT

BRAKE

(

+)

INPUT

)

(-

z

<(

~

z

a..

.,...-

GREEN BLACK/WHITE

BROWN/BLACK RED/WHITE TRUNK BLUE/BLACK PURPLE/WHITE GRAY BROWN/RED VIOLET/BLACK

DOOR INPUT ILLUMINATED ENTRY OUTPUT ( - )

HORN

START STATUS TACH HOOD PIN INPUT BRAKE AUX

OUTPUT (

RELEASE

INPUT

1 OUTPUT ( - )

3 Pin Parking Light Harness

(-)

(

I

+ )

- ) OUTPUT

ACTIVE

(-)

OUTPUT (

- )

C/)

ZI-

-I

a..(!)

-

C")

_J

I-

a::

<(

I-

C/)

z

a..

c.o

BLACK WHITE/RED PARKING LIGHT INPUT WHITE PARKING LIGHT

6 Pin

GROUND

Start

PURPLE STARTER RED ORANGE PINK/WHITE RED/WHITE PINK

Harness

BATTERY 12V ( ACCESSORY IGNITION 2 BATTERY 12V ( IGNITION

OUTPUT

OUTPUT-

+)

( + )

1

( + )

+)

( + )

1

MOTOR SIDE

4

ca5153/5153sst rev A

4 Pin Alternate Harness

z~

-u

o...o

N_.J

BLACK/YELLOW GREEN/WHITE LT BLUE L T GREEN/BLACK FACTORY

PULSE PULSE AFTER FACTORY ARM

2 Pin Door Lock Harness

BLUE GREEN

11

Pin Main Harness

UNLOCK LOCK

(-)

DURING

DISARM

(-)

CRANK

SHUIDOWN

I

PULSE AFTER START ( - )

(-)

I

PULSE BEFORE START ( - )

1

GRAY/RED

PARKING

BRAKE

INPUT

(-)

Locate the vehicle's parking brake wire.

Verification:

This wire

will

register ground when the vehicle's

BRAKE is engaged.

NOTE:

The

following

connection is required for

Manual

Transmission

Mode.

2

PURPLE

DOOR TRIGGER INPUT

(

+)

Locate the vehicle's dome light or door pin switch wire.

Verification:

opened and the interior light is on. This wire register ground or "0"

This wire will

Volts when the door

register positive voltage

will

is

closed and the interior light is

(POS)

when the door is

off.

Connect the PURPLE wire to the vehicle's positive door input wire(s).

PARKING

NOTE:

Certain vehicles may require multiple connections. Refer to vehicle

application guide.

5

3

GREEN

DOOR TRIGGER INPUT

(-

)

Locate the vehicle's

Verification:

dome

This wire and the interior light door is

closed and the interior

Connect the GREEN wire to the

NOTE:

Certain

application

4

BLACK/WHITE

vehicles

guide.

light or door pin switch wire.

register ground (NEG) when the door is opened

will

register positive

is on. This wire

will

light is off.

vehicle's

may require

multiple

negative door input wire(s).

connections. Refer to

ILLUMINATED ENTRY OUTPUT

voltage

vehicle

(-)

when the

This wire provides a ( - ) 500mA output for 30 seconds when the system is disarmed

Locate the

capable of driving relays.

vehicle's dome

Verification:

vehicle's dome

This wire

is turned

light

or pin switch wire.

light

will register positive voltage

ON.

or ground when the

5

BROWN/BLACK

Locate the vehicle's

Verification:

This wire

horn wire.

will

HORN

register at positive

OUTPUT ( -)

ground when the horn switch is pressed.

Connect the BROWN/BLACK wire to the output,

6

SOOmA.

RED/WHITE

TRUNK RELEASE OUTPUT ( - )

vehicle's

horn wire. This is a

Locate the vehicle's trunk release wire at the trunk

Verification:

the trunk

This is a

This wire will

release is activated.

low current output, 500mA and is

register either positive

configurable in option programming.

voltage

release

voltage

and register

low

switch.

or ground when

current

6

ca5153

5153sst rev A

I

7

BLUE/BLACK

START STATUS

I

ACTIVE

OUTPUT

(-)

This wire provides a ground output when the remote start function is activated and remains until 4 seconds after the remote start is shutdown. If be used for multiple application's a

1 amp diode is required in-line with the stripe

this wire

will

facing the control module.

8

PURPLE/WHITE

TACH

INPUT

Locate the vehicle's ignition coil or fuel injector in the engine compartment.

Verification:

1.

Set voltmeter to

2.

Attach positive lead of a volt meter to a constant 12-volt source.

3.

Attach negative

4.

Start

the engine.

5. Have someone press connected to the correct wire, the voltage reading

Test using the

AC

VOLTS.

lead

of a volt meter

on

the gas pedal slightly as you monitor the meter. If

following

to the wire to be tested.

procedure:

will

increase as the engine's

RPM increases.

Connect the or

fuel injector.

9

GRAY

PURPLE/WHITE wire to the negative side of the vehicle ignition coil

HOOD

INPUT

(-)

Install a Hood Pin

required for Remote

Verification:

Switch and connect to the GRAY wire. This connection is

Start.

This wire when connected

vehicle's hood is opened.

Connect the GRAY wire to the hood pin.

NOTE:

1

0

Be

sure to loom the wire, and seal the grommet.

BROWN/RED

Locate the vehicle's brake light wire at the brake pedal mounted switch. This connection is required for Remote

Verification:

This wire registers positive voltage when the brake pedal is

pressed.

Connect the BROWN/RED wire to the vehicle's brake light wire.

2012

Audiovox

Electronics

Corporation.

All

rights

reserved.

will

BRAKE INPUT

Start.

register ground when the

(

+)

7

11

VIOLET/BLACK

AUX 1

This wire provides a

( - )

SOOmA

output capable of driving relays. For Control of

optional accessories (i.e. Power Window/Sunroof, etc.).

activate refer to the transmitter button configuration chart. Please refer to the

To

selectable options for timing.

3 Pin Parking Light Harness

1

Connect the BLACK wire to a

BLACK

solid chassis ground point using a ring

self tapping screw (not supplied). ensure a good connection. The recommended grounding point is a metal

the driver's side kick panel area.

in

not ground the BLACK wire with any other vehicle components.

NOTE:

Do

GROUND

Scrape

terminal

away paint from the grounding point to

and

surface

2

3

WHITE/RED

WHITE

PARKING LIGHT INPUT

PARKING LIGHT

OUTPUT

Locate the parking light output wire at the vehicle's light switch.

Verification:

This wire registers positive voltage

when the parking lights are

turned on.

Positive switching Parking Lights:

Connect the

WHITE/RED

Connect the WHITE

wire to the parking light output wire.

wire to a 15 Amp max fused battery source.

Negative switching Parking Lights:

Connect the Connect the

WHITE/RED wire to a good chassis ground.

WHITE

wire to the parking light output wire.

8

ca5153

5153sst rev A

I

6 Pin

Start

Harness

1

PURPLE

STARTER OUTPUT (

+ )

Locate the vehicle starter wire.

when the key is turned to the

Verification:

This wire registers voltage

only

START position.

Verification:

The starter wire registers voltage when the key is turned to the START position.

vehicle starter wire.

Connect

2

PURPLE

the

wire to

RED BATTERY 12V (

the

+ )

Locate 1 of the vehicle's constant 12 Volt battery wires at the ignition switch.

Verification:

This wire

will register (

+ )

voltage

in

positions of the ignition

all

switch.

Connect the RED wire to the constant 12 Volt battery wire.

connections are made.

NOTE:

3

Remove

ORANGE

fuses until

all

ACCESSORY 1

(

+ )

Locate the vehicle's accessory wire at the ignition switch.

Verification:

(Accessory) and the

This wire registers voltage when the key is turned to ACC

ON (or RUN) position. The voltage drops out when the

key is turned to the START (or CRANK) position.

Connect the ORANGE wire to the vehicle's accessory wire.

+ )

(

4

PINK/WHITE

IGNITION

2

Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped).

Verification: This wire registers voltage when the key is turned to the ON

RUN) position, but not the drop out when the key is turned to the START (or CRANK) position.

PINK/WHITE

Connect

the

Programmable output:

Audiovox

2012

Electronics

Corporation.

the

to

wire

IGN, ACC,

rights reserved.

All

ACC

(Accessory) position. The voltage does not

vehicle's

Start.

ignition

2

(or

wire.

9

5

RED

!WHITE

BATTERY 12V

(

+ )

Locate 1 of the

Verification:

vehicle's

This wire

switch.

Connect the RED/WHITE

NOTE:

6

Locate the

Remove

PINK

vehicle's

Verification:

all

fuses

ignition wire at the ignition switch.

This wire registers voltage RUN) position. The START (or CRANK) position.

Connect the This wire

is

PINK

also

wire to the

used for

constant 12

will register (

Volt

battery wires at the ignition switch.

+)

voltage

wire to the constant 12

until all

connections are made.

IGNITION

1

when the key is turned to the

voltage

Ignition

does not drop out when the key is turned to the

vehicle's Ignition

1

Output.

wire.

(

Volt

+)

in

all positions of the ignition

battery wire.

ON

(or

4 Pin Alternate Harness

1

Locate the

Connect the BLACKNELLOW wire as shown relay (not supplied).

This output is configurable

2

This wire

is shutdown. vehicle's

BLACKNELLOW

vehicle's

Verification:

the ignition switch.

GREEN!WHITE

will supply a

typically

used to re-lock

It

can

accessories from remaining on after remote start shutdown.

PULSE

DURING

second starter (crank) wire at the ignition switch. (if equipped)

This wire registers

in

option programming.

voltage only

PULSE AFTER SHUTDOWN

( - ) 500mA

pulse

after the remote start shuts down. This

the vehicle's doors if they

also

be used to

pulse a door pin-switch wire to prevent the

CRANK

in

the start (crank) position of

in

the diagram

unlock

(-)

below. Use

an

SPOT

(-)

upon remote start

This output is configurable

10

in

option programming.

ca5153/5153sst rev A

3

LTBLUE

FACTORY ARM

I

(-)

This wire will supply a

(-)

500mA

PULSE

AFTER

START

pulse both upon arming the system and upon

successful completion of the remote start activation sequence and is

used to re-lock the vehicle's doors upon remote start if necessary.

option programming.

This output is configurable

GREEN/BLACK

4

This wire

LT

will supply

a ( - ) 500mA pulse the remote start feature is activated. Locate the factory perimeter wire from the key

Verification:

cylinder

This wire registers ground if the key is turned to the

in

FACTORY DISARM PULSE BEFORE

both upon disarming the system and when

inside the drivers door.

I

START

(-)

alarm

position in the driver's door cylinder.

typically

disarm

unlock

option programming.

This output is configurable

2 Pin Door

1

2

The door

BLUE

GREEN

lock I unlock outputs are designed to control

in

Lock Harness

...

UNLOCK

LOCK

(-)

systems which may require additional parts. chart to see which type of door lock system is types are shown

the following

in

diagrams.

(-)

several

Please

in

review the wire and

your vehicle. The most common

different types of

location

2012 Audiovox Electronics Corporation.

All

rights reserved.

11

Negative

All

Door Lock and Unlock: Locate the lock

Switching

Locks

unlock switch.

I

unlock wire at the vehicle's lock

I

Verification:

These wires

will register ground when the Lock and Unlock

switches are activated.

Connect the GREEN and BLUE wires shown

Negative Locks:

GREEN(-)

Lock

BLUE

(-)

Unlock Output

in

the diagram below.

Output

Vehicle Door Lock

Control Relays

Positive

All Door Lock and Unlock: Locate the lock

Switching

Locks

I

unlock switch.

Verification:

These wires

will register positive voltage when the Lock and

Unlock switches are activated.

Connect the GREEN and BLUE wires shown

Positive Locks:

Vehicle

Door Lock

Control Relays

unlock wire at the vehicle's lock

in

the diagram below.

GREEN

(-)Lock

Output

BLUE(-)

Unlock Output

I

12

ca5153/5153sst rev A

Reverse Polarity Locks (S-Wire Door

All Door Lock and Unlock:

Locate the

lock

unlock switch.

locks)

unlock

I

wire at the vehicle's

lock

I

Verification:

These wires

will rest at ground and register positive

voltage when the Lock and Unlock switches are activated.

Connect the GREEN and BLUE or BLUE/GREEN wires shown below

using (2)

SPOT relays

Reverse

(not supplied).

Polarity

Locks:

Cut

GREEN(-)

-..----~

BLUE(

Lock Output

-) Unlock Output

To Door Lock Motor

the diagram

in

Negative

Multiplexed

All Door Lock and Unlock: unlock

switch.

Verification:

Please consult

Locks

This wire

the wire and

Locate the

show variable

will

location

lock

unlock

I

wire at the

ground when the switch is activated.

chart for specific resistor

your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown

supplied).

below

using (2)

Multiplex

SPOT relays

Locks:

(not

vehicle's lock

values

the diagram

in

I

for

2012 Audiovox Electronics Corporation.

rights reserved.

All

13

Positive

Multiplexed Locks

All Door Lock and Unlock: Locate the lock

I

unlock wire at the vehicle's lock

unlock switch.

Verification:

This wire will show variable positive voltage when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown below using (2) SPOT relays (not supplied).

Multiplex Locks:

Vehicle Door Lock

Control Relays

in

the diagram

I

Adding Aftermarket Actuators

After BLUE wires shown

installing

aftermarket actuators, (not supplied). Connect the GREEN and

in

the diagram below using (2)

-------f

87

,.----t-----1

Fused +12 Volt Battery Source

Fused

+

Battery Source

12 Volt

SPOT

relays (not supplied).

BLUE (-) Unlock

Output

14

ca5153

I

5153sst rev A

Additional

Antenna

I

LED

:Ports

Programming Port

I

Mount the supplied antenna/receiver to a

not block the driver's vision. A good location is

will

that

windshield on any receiver

metallic window

cable

near the rear view mirror.

as this

film,

to the

control module

Be

effect system range. Route the antenna/

will

and plug

clear spot

careful

not to mount the antenna/receiver

into the antenna port.

the vehicle's windshield

on

the

on

usually

high

Data Bus

This 4 pin port is used for

Interface Port

Flashlogic Door Lock and Transponder Databus

Interfaces to communicate with the vehicle's Databus. When using the

control

the following function

Tach Trunk/Hatch Door Lock Control Passlock

Dome Light Supervision Transponder Interface Factory

Flashlogic

Door Lock and Transponder Interface

options may be

list available per

Input

Open Diesel Glow Plug Input

Alarm

Arm

available. Please

the tech service web site.

vehicle

on

Brake Safety Shut Down

Disarm

I

Manual controls

refer to the

Passkey Interface (GM Only)

I

Arm

020

Disarm Inputs (factory

system)

modules

(Data to Data)

Activation

OBI

the

port to

keyless

Telematic Interface Port

This 4 pin port is used for Telematic which can

Door Lock

Sliding

control some of the

Control

Doors AUX

Car Find Remote Start

Audiovox Electronics Corporation.

2012

All

Interface

following

Trunk

accessories, such as CarLink,

features.

Release

Output

rights reserved. 1 5

Set

Up

&

Programming

Transmitter Programming - Feature Bank 1

1.

2.

3.

4.

5.

6.

NOTE:

system.

NOTE:

transmitter

NOTE:

ignition is turned ON,

the system.

Turn the ignition

Press and hold the valet/override button. Within 1 0 Press 1 button of each transmitter you wish to program.

The system

Pressing the override button at anytime during programming

the next bank.

The system This system has 1 button programming which programs

The system

will

This system has

seconds the system

will respond with 1 chirp for each accepted transmitter.

erase the oldest transmitter

ON.

will

chirp (3) three times.

will advance to

will exit transmitter programming after 15 seconds of inactivity.

all

channels of the

will hold

the LED

up to 4 transmitters

in

PTN

- Programmed Transmitter Notification. Each time the will

flash the number of transmitters programmed to

in

memory, programming a 5th

memory.

Manual

1.

2.

3.

4.

5.

6.

Feature

Turn the ignition ON. Press and hold the valet/override button. Within 1 Use the valet/override button to advance through each option bank. For

feature programming advance to Feature Bank

four,

Use the transmitter

bank, the system

Press the transmitter

flash indicating the changed feature.

(5)

Programming - Feature Bank 2 - 5

0 seconds the system

five, (6) six and (7) seven chirps.

will chirp to match the feature number.

Defaulting All Features:

feature banks

will

default

will

chirp

0

button to

@

button to change the desired feature. The LED

Pressing the

all

features and return you to feature bank 2

scroll through the selections

@

(3)

three times.

2,

3,

4 or

button anytime while

in

5,

which is

in

each feature

any of the

- 4 chirps.

(4)

will

NOTE:

ignition is on, there is no time limit.

16

The system

will

remain

in

feature programming mode as

To

exit programming turn the

long

as the

IGNITION

ca5153

OFF.

I

5153sst rev A

Feature

Transmitter

Bank

1

-

Programming

3 Chirps

Refer to transmitter programming.

Factory Disarm

Lt

Green

2

NOTE:

I

On

Black

this

model

the

Lt

Green

Factory Disarm

I

Black

Output

5

will

wire

can be

override

configured

changes

Factory Disarm

I

Start Status

in

Bank

made

in

Bank

3

or

Bank

5.

Any

changes

3.

to

this

feature

in

Bank

2012 Audiovox

Electronics

Corporation.

All

rights reserved.

17

Feature Bank 5 4 Pin Alternate

Chirps

7

•

Output

Control

Yellow Output

I

Black

4

Green

Lt

the

model

NOTE: On

18

this

Pulse Crank Running

Black

I

During Ground

wire

Output

override

will

configured

can be

changes made

While

Ignition

in

Bank

changes

Any

5.

Bank

or

3

3.

to

5

Bank

In

feature

this

ca5153/5153sst rev A

Tach Programming

The unit will tachless

option is turned

remote start without first programming tach, the unit will flash times indicating tach has not been properly

programmed to the specific vehicle, the unit may not

not operate

unless

ON.

a tach

signal is programmed or the

If an attempt is made to start the

the parking

learned

and stored.

If the tach rate is not

realize

vehicle

vehicle is running in certain instances and reengage the starter motor.

The Remote

packs, or

1. Turn the ignition key to the

2.

3.

4.

Start

single

unit

injector.

Press and Immediately Press and

will learn the tach rate of most

To

learn

tach:

ON position.

release

turn the ignition key

hold

the valet/override button 3 times.

OFF.

the valet/override button, then start the

vehicle's single coil, multiple coil

vehicle

the key.

5.

When the unit senses the tach

signal,

the parking

lights will

flash.

6.

Allow

the

vehicle to

settle to a

normal idle

speed.

via the

lights

that the

using

begin to

7

7.

Release parking

the

valet/program

lights will

turn on for

tach signal is stored and the unit has exited tach

NOTE:

If

the unit

fails

to

learn tach rate due to an improper tach connection or a

poor tach source, the parking lights will and connect the

the tach

Smart

learn

Tachless Mode

Smart Tachless the system and when activated in option programming to

PURPLE/WHITE wire to the proper tach signal, and then repeat

routine.

Mode is

available only

will automatically

Tachless without the need to enter the feature

programming mode.

1.

Activate the remote start. The parking lights should times indicating no tach

signal has been learned.

push-button switch.

2

seconds, indicating that the

1

long

learn mode.

not

flash.

if a tach

To

correct this situation, locate

signal has never been

change the Tach Mode feature

chirp and the

learned

learned to

begin

flashing

7

2.

3.

Within the 7

The system

mode.

2012

Audiovox

Electronics

Corporation.

All

flash

will

time period, press and

chirp

rights reserved.

hold the

1

time indicating the system is now in tachless

0

button.

19

Feature Descriptions

Feature

Bank

Security

2 -

Silent

1 -

2 - 8

9 - OBI

interface with external modules.

Feature

Choice:

- Silent arming/disarming upon first press of lock/unlock,

ON unlock system lock/unlock buttons.

OFF -

Not

Port

OBI ADS

a second time will

will only

normal

available

Protocol:

Protocol

Bank

Controls

sound the arm/disarm chirps upon a second press of the

arm/disarm chirps upon the first press of

on

Output

3-

the

this

Determines the protocol type

model.

Control

normal

activate the arm/disarm chirps respectively. The

arm/disarm chirps of the security system.

lock/

which the

in

pressing

lock/unlock.

port uses to

OBI

Extended

1 -

output wires.

Second

1

Seconds

3.5 Second

1 second

30 Second

1 second Double Pulse

second

Lock

unlock pulse.

Pulse:

- Single 1 second

- Single

Lock,

unlock pulse.

Double Pulse

Lock,

Lock, 1 Second Unlock

Controls

3.5 second

Double Pulse Unlock

the timing of the BLUE and GREEN

lock pulse, single

Unlock-

Single 1 second

Single

-

- Double

1 second

30 second lock pulse, double

1 second

unlock pulse.

3.5 second unlock pulse. lock pulse, double

lock pulse, single

lock

1

20

ca5153

5153sst rev A

I

2 -

Factory

output.

Disarm: Controls

the timing of the

LT.

GREEN/BLACK factory disarm

Factory Disarm activation.

2nd Start Status -

during the remote start

NOTE: On

3 or Bank

Bank

3 -

ON

3.

Ignition

or

OFF. OFF Lock and

ignition is turned off. Lock

Unlock-

Single

Same output as

Single

1 second pulse

1 second

cycle.

this

model

5.

Any changes to this feature

Controlled

- Door Unlock-

Only

- Doors

the Lt Green

Locks:

locks

not activated by ignition.

Doors lock

lock

Control

when ignition is turned on

unlock

pulse

I

Black Output

with 2nd press of

with unlock

in

Bank 5

of door

with unlock

wire can be configured

will

locks

and remote start

unlock.

and continuous (

override changes made

when the ignition is

when ignition is turned on and unlock

only.

- ) output

in

Bank

in

cycled

when

4 -

Trunk

of the

5 -

Horn

some

Unlock Only

Output

Doors unlock when ignition is turned off only.

Timing

- Red/White

Output:

Controls the output timing/type

RED/WHITE output.

1 Second

1

0 Second - Continuous output for 1

20

Seconds - Continuous output for

Latched until IGN ON

Pulse -

1 second

pulse

output.

0

20

- Continuous output until

seconds.

the

ON. Latched ON until Button Press - Continuous output

is pressed again.

Output

vehicle will require a

16mS 1

Timing:

OmS

Control

longer pulse

the minimum horn

to activate the factory horn.

30mS 40mS 50mS

pulse

vehicle's

ignition is turned

until the activation button

time

in

milli

seconds,

6 -

Real Panic:

ON

- Randomized horn honks when panic is triggered.

OFF

2012 Audiovox

Electronics

- Standard pattern horn honks when panic is triggered.

Controls

Corporation.

All

the panic out when triggered from the transmitter.

rights reseNed. 21

7-

AUX 1: Controls the VIOLET/BLACK AUX 1 output activation type and timing.

Push and Hold - Output is continuously active until transmitter button is released.

Latched - Output stays active until button is pressed again. Latched until IGN ON - Output stays active until the ignition is turned on.

is

Dome Light Output - Output used for illuminated entry and

not controlled

by the AUX 1 function of the transmitter.

Defrost Output Single Pulse - Single 1 second pulse after start Defrost Output Latched 5 Minutes - 5 minute continuous output after

remote start.

Feature Bank 4-Remote Start Control

1 - RF Start Chirp: Turns remote start activation confirmation chirps ON or

2 -

Run

Time: Controls the time

in

minutes that the vehicle will stay running

OFF.

under control of the remote start until the system times out. The system may also be

shut down at any time by use of the transmitter or system shutdowns.

3-

Running Lights: Controls the WHITE parking light output wire during remote

start.

Steady - Parking lights constant during the remote start cycle.

Flashing - Parking lights flash at a slow pace during the remote start cycle.

4 - Tach Mode: Determines how the system monitors the engine running during

remote start.

Tach - Hard wired directly to the tach wire of the vehicle to monitor AC voltage.

Tachless (Crank AverageNoltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key and then monitors the

in

change

voltage after remote start.

Hybrid (Crank Average

the last 8 times the vehicle was started with the

OBI

Port - Monitors the vehicle's tach rate through

connected to the

22

OBI

I No Voltage)- Determines crank time by averaging

key.

an

interface module

port.

ca5153/5153sst rev A

5 - Voltage Level:

(see tach mode)

The

voltage

variance for remote start when set to tachless.

HIGH

-The

variance

in

is activated to after the engine is running must be greater than LOW

- The variance

in

is activated to after the engine is running may be

6 -

Crank

7 -

Crank

will

crank the

Time:

1 Second

Average

vehicle's

Preset output times for the PURPLE starter wire.

0.8

Seconds 1

I

Crank

starter.

Crank Average - Determines crank time by averaging the vehicle

Preset

8 - Gas

I Diesel:

was started with the

Time-

Preset starter output time. (see crank time)

Selects engine type and delay

during remote start activation.

battery

Time:

voltage

The

key.

from before the remote start

0.5 volts.

from before the remote start

less

than

0.5 volts.

.5

Seconds 2 Seconds 4 Seconds

length

of time

in

which the remote start

last

8 times the

time for the starter output wire

9 -

a

single

10

Gas -

1

0

Gasoline

engine, no

Second Delay

delay

- Diesel engine,

for the starter output wire.

delays

the starter output wire for 1 0

seconds after the ignition has been powered up by the remote start. 15 Second

Delay

-

Diesel

engine,

delays

the starter output wire for 15

seconds after the ignition has been powered up by the remote start. 20

Second

Delay

-

Diesel

engine,

delays

the starter output wire for

seconds after the ignition has been powered up by the remote start. 45 Second

Delay

-

Diesel engine,

delays

the starter output wire for 45

seconds after the ignition has been powered up by the remote start.

Single

-

IGN

Ignition

I

Double Pulse

or

double press from the transmitter.

2

Output:

2

Programmable high current output.

-

Ignition output during remote start.

Start:

Switches the remote start activation between

Accessory - Accessory output during remote start.

20

Start

I

Crank - Crank output during remote start.

11

- 2

or

3

Hour

2012 Audiovox

Electronics

Start:

Corporation.

Not

All

available

rights reserved.

on

this model.

23

12 - Turbo Timer: Not available on this model.

13 - Transmission Mode: Select the type of remote start activation based on

the vehicle's transmission type.

Automatic - For use with automatic transmission vehicles. Standard remote start operation. Manual - For use with manual transmission vehicles. Remote start ready mode must be set upon exit of vehicle to enable remote start.

Feature Bank

5-4

Pin Alternate Output Control

1 - Black/Yellow Output : Controls the BLACKNELLOW output activation type

and timing.

Pulse During Crank - Output becomes active with the same timing as the

starter output wire, during crank only.

Ground While Running - Continuous output for the entire remote start

sequence until after the vehicle shuts down.

Ignition - Output becomes active with the same timing as the ignition output

and does not drop out during crank. Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank.

2-

Green/White

Output:

Controls the GREEN/WHITE output activation type and

timing.

Pulse After Shutdown - 1 second pulse after the remote start has

shutdown. Ground While Running - Continuous output for the entire remote start

sequence until after the vehicle shuts down.

Ignition

-Output

and does not drop out during crank. Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank.

Pulse During Crank - Output becomes active with the same timing as the

starter output wire, during crank only.

24

becomes active with the same timing as the ignition output

ca5153/5153sst rev A

Green/Black Output

Lt

4-

type and timing.

Controls

:

the

GREEN/BLACK output activation

LT

3

Pulse

before Start

activated. Also Ground

sequence

While

until

During

I

1 second

a

Unlock-

pulse

Running - Continuous output for the entire remote start

after the

vehicle

1 second pulse when remote start is

when

unlock is pressed.

shuts down.

Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Pulse starter output wire, during crank

Blue Output

Lt

Pulse

sequence and has confirmed the when

Ground sequence until

During Crank - Output becomes active with the same timing as the

only.

Controls

:

After Start

unlock

is pressed.

During Lock - 1 second

I

the

vehicle

pulse

after the remote start

is running.

Also

1 second

a

BLUE output activation type and timing.

LT

While Running - Continuous output for the entire remote start

after the

vehicle

shuts down.

pulse

Ignition

-Output

becomes active with the same timing as the ignition output

and does not drop out during crank. Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank.

Pulse

starter output wire, during crank

During Crank - Output becomes active with the same timing as the

only.

2012 Audiovox

Electronics Corporation.

All

rights reserved.

25

Transmitter Button Functions

1

Way

Tra nsm itte r

Lock

Unlock

Car

Panic

Find

I

Start

Operation

Method

AUX

1

X

Push and

Hold

(3

Sec)

26

ca5153

I

5153sst rev A

to start, the parking

the remote start shuts down or

If

fails

the patterns below indicating the shutdown input.

shutdown, turn the ignition

manually

To

enter diagnostics and view the

and press and release

the

._.

button.

last

lights will flash

one of

ON

FLASHES

LED

3 Flashes

4 Flashes

5 Flashes

Flashes

7

SHUTDOWN ZONE

Hood

Input

Brake Input

Remote

Manual transmission

Tach

Start Valet

Transmission Mode not set

models only)

learned I Crank Average not

not

Mode

(manual

learned

27

1\)

(X)

BLUE

UNLOCK

(-)

GREEN

LOCK

(-)

BLACK/YELLOW

PULSE

DURING CRANK

(

- )

GREEN/WHITE

PULSE AFTER SHUTDOWN (

- )

LT

BLUE

FACTORY

ARM

I

PULSE AFTER START ( - )

L T GREEN/BLACK

FACTORY DISARM

I

PULSE BEFORE START ( - )

D

BLACK GROUND WHITE/RED PARKING LIGHT INPUT WHITE PARKING LIGHT

OUTPUT

E~

GRAY/RED PARKING BRAKE

INPUT

(

- )

n:~

PURPLE

DOOR INPUT

(

+ )

GREEN

DOOR INPUT

( - )

:s~

BLACK/WHITE ILLUMINATED

ENTRY OUTPUT (

- )

BROWN/BLACK HORN

OUTPUT ( - )

~~

RED/WHITE

TRUNK RELEASE OUTPUT

(-)

IU

u;

BLUE/BLACK START STATUS

I

ACTIVE OUTPUT

(-

)

PURPLE/WHITE TACH INPUT

o;;

GRAY

HOOD INPUT

(

- )

0~

BROWN/RED BRAKE

INPUT

(

+ )

ULO

VIOLET/BLACK

AUX 1 OUTPUT (

- )

OBI

PORT

(J9

;

ANTENNA

)

LED VALET

TELEMATIC PORT

(")

Ill

~

PURPLE

STARTER OUTPUT - MOTOR SIDE

(

+ )

-

RED

BATIERY

12V (

+)

0'1

......

ORANGE

ACCESSORY

1

(

+ )

~

PINK/WHITE IGNITION

2

(

+)

en

~

RED/WHITE

BATTERY 12V (

+)

co

PINK

IGNITION

1

(

+)

<

)>

2012 Audiovox

Electronics

Corporation.

All

rights reserved. 29

Audiovox Electronics Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

FCC COMPLIANCE

This device complies with Part 15 of the

Industry

1.

This device may not cause harmful interference, and

2.

This device must accept any interference received, including any interference

Canada. Operation is subject to the

that may cause undesired operation.

Warning!

Changes or modifications not expressly approved by the party responsible for compliance could

32

void the user's authority to operate the equipment.

R41

0-192-380

FCC rules and with

following

two conditions:

RSS-21 0

ca5153

of

I

5153sst rev

A

CCCc~l./.l~m

Automatic

Remote

IMPORTANT

applicable

SAFETY PRECAUTIONS

2012 Audiovox Electronics

Start

NOTE:

The operation of the Security and Convenience System as described in this manual is

to most vehicles.

Corporation.

Manual

I

and

However, due to the configuration of some

may not

rights reserved.

All

Keyless

apply. Please

Transmission

see your

Entry

vehicles,

installing dealer

System

some functions

for more information.

AND/OR

4280477

Table

of Contents

Using Your Remote

Using the Keyless Entry ................................................................... 3

Two Stage Door Unlock (optional) ................................................... 3

Activating Trunk Release (optional) ................................................ 3

Activating AUX 1 (optional) .............................................................. 3

Using the Progressive Car Finder Feature ...................................... 3

Using the Personal Protection Alarm ............................................... 3

Programmed Transmitter Notification .............................................. 4

Valet Eliminating Lock

Mode ........................................................................................ 4

Using Your Remote

Remote Start Ready Mode ................................................................ 5

Cancelling Remote Starting Your

Remote Start Shutdown ................................................................... 6

Entering Your Preheating or Precooling the User Programmable Run Time

Using the Quick Stop Feature .......................................................... 7

Operating the Daily Start Timer ........................................................ 7

Remote Start Safety Features ......................................................... 7

Remote Start Ready Mode ............................................. 5

Control

I

Unlock Notification Chirps ................................... 4

Starter

Vehicle

...............................................................

................................................................

Vehicle

while it is Running via Remote Start ........... 6

.......................................................... 6

Vehicle's Interior

............................... 6

I Run Time Extension ...................... 6

3

5

Transmitter Replacing

Warranty

2

Button

Remote

Control

Information

Functions

........................................................... 8

Batteries ............................................... 8

.........................................................................

10

ca5153/5153sst rev A

Using Your Remote Control

Using the Keyless Entry

The @ button is used to lock the vehicle's doors, the vehicle's doors.

To

lock or unlock the doors simply press and release the desired

ri]

button is used to unlock the

function button one time. For your convenience, the parking lights will flash once when the doors are unlocked and twice when the door are locked.

NOTE: The system is equipped with a feature called Silent Choice. If enabled, the system requires a second press of the

@ or

ri]

button to activate

an

audible locking/ unlocking response from the vehicle. If your system is set up for 2 step unlock, a third press of unlock will activate the audible response.

Two Stage

If this feature is enabled

unlock only the driver's door. Press

Door

Unlock (Optional)

on

your system, pressing the

ri]

again within three seconds to unlock the

ri]

button one time will

remaining doors.

Activating

The

ri]

press and hold the

the Trunk Release Feature (Optional)

button is used to open the trunk of the vehicle.

ri]

button for 3 seconds.

To

open the vehicle's trunk

Activating

If this feature is enabled

simultaneously will activate

AUX

1 (Optional)

on

your system, pressing the @ and

an

optional feature. This feature can be programmed

ri]

buttons

for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine the functionality of your system.

Using the Progressive Car Finder Feature

Press the and sound 5 times at low volume, increasing

~>))

button to locate your vehicle. The system will flash the parking lights

in

volume each time the button is

pressed.

Using the

Press and hold the alarm. During panic mode, the normal function of the transmitter buttons will suspended. The transmitter's @ and

door (if the option is installed).

Personal

~>))

Protection

Alarm

(Panic)

button for 3 seconds to activate the personal protection

be

ri]

buttons can be used to lock and unlock the

To

stop the alarm, press and hold the

~>))

button

on

the transmitter again for 3 seconds. The system will automatically stop after 30

seconds.

2012 Audiovox Electronics Corporation.

All

rights reserved.

3

Programmed

Transmitter

Notification

As a security precaution each time the

light

with flash

the number of transmitters programmed into the system. This

to identify unauthorized transmitters from accessing your vehicle. If

vehicle's

ignition is turn

on

the status LED

you

believe

unauthorized transmitter has been programmed to your system, contact your

installing dealer

for assistance.

Valet Mode

Valet valet

Eliminating

Mode

mode

1.

2.

3.

4.

is

used to

disable

simply follow

Turn the Push and

vehicle's

hold The LED will Release

Lock

the programming/valet button.

I

Unlock Notification Chirps

the system from remote starting.

the 4 steps

ignition

outlined below:

ON.

the programming/valet button.

turn

on

solid

when

valet

mode

is

active

To

enter or exit

helps

an

System

lock

and

unlock

notification chirps can be toggled

entering the programming feature banks.

1.

2.

Turn the ignition Press and

will

respond with 1 chirp

release

ON

then

OFF.

the valet/programming button 3 times. The system

for

ON

or 2 chirps for

ON

OFF.

or

OFF

without

4

ca5153/5153sst rev A

Using Your Remote Starter

Remote

with a manual

Remote

To

activate the remote start function, the system must first

Start

Ready

Mode

transmission.

Ready

Mode -Manual

must

be

enabled

Transmission

if

your

vehicle

Vehicles

be

in

Remote Start

is

equipped

Only

Ready Mode. Follow the steps below to enter remote start ready mode.

1.

2.

While the engine is running by the ignition key; a.

Set the parking brake

b.

Place the transmission

in

neutral.

With your foot off the brake pedal, press and release the 0 button 2

times within 2 seconds. The LED will flash 3 times and the parking

3.

lights will turn Remove the keys from the ignition, the vehicle will remain running

on

to confirm the system has entered quick stop mode.

quick stop mode.

4.

5.

Exit the vehicle and close all vehicle doors. Within 1 minute of step

1,

press the

(2)

button to lock the vehicle's doors. The vehicle will shutdown and sound 1 short chirp then 1 long chirp to confirm ready mode is set.

in

Cancelling

Remote

Start

Ready

Mode

The system will exit remote start ready mode if any of the following occur:

Open any door Open the hood or trunk (if connected)

Press the brake Release the parking brake

Turn the ignition

ON

2012 Audiovox Electronics Corporation.

All

rights reserved.

5

Remote

To

activate the remote start function, press and release the 2 seconds. The system system are correct, the vehicle will will

turn on (or flash depending on system settings) as a visual indication that the

Starting

Your

Vehicle

will sound, the parking lights

will

check the vehicle to ensure it is safe to start.

start within 5 seconds. The vehicle's parking lights

0

button 2 times within

will flash 1 time and the

If all

safety parameters

vehicle has started and is running.

If your vehicle stalls or does not start, the system will

pause 5 seconds, then try 2 more times to start the vehicle (a total of 3 attempts). The system seconds between each start attempt. If attempt, the system

will abort the remote vehicle start process.

Note: Do not leave children or animals unattended

the vehicle does not start after the 3rd

in

the vehicle when using the

remote start feature. Note: Manual transmission vehicles - Remote

Remote

Press and hold the

Entering

1.

2.

3.

Start

the

Shutdown

0

button for 3 seconds to turn the vehicle off.

Vehicle

while

it

is

Running

Unlock the vehicle's doors. Enter the vehicle.

DO

NOT PRESS THE BRAKE PEDAL!

Insert the key into the ignition switch and turn to the

Start

via

Ready Mode must be set.

Remote

Vehicle

ON

position.

will pause 5

Start

or RUN

4.

Press the brake pedal. The remote vehicle starter will disengage and

the vehicle

Preheating

or

Precooling

Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle's interior to your setting.

User

Programmable

Run

The system has the ability to allow running under control of the remote start. This the current run time setting during the current remote start set to run 15 minutes and the time remaining is 4 minutes, extending the run time will

reset the countdown timer to 15 minutes and your vehicle

for another 15 minutes.

1.

The remote start must already

2.

3.

6

Press and release the The system

confirm that the run time has been reset.

will

operate normally.

the

Time

Vehicle's

I

Run

interior

Time

Extension

the user to extend the time the vehicle

will

only extend the run time back to

cycle. If

will

Follow

will

the steps below to extend the vehicle's run time.

be

active.

0

button 4 times.

chirp 1 time and flash the parking lights 4 times to

your system is

continue to run

will

be

ca5153/5153sst rev A

Using

If

you want to make a short stop and keep your vehicle running (to keep the

interior warm or cool), the quick-stop feature

your

the

"Quick-stop"

Feature

-

Automatic

vehicle secure and your keys with you.

To

engage

quick

stop:

Transmission

Vehicles

allows you to do this while keeping

1.

2.

Stop the vehicle and

place the transmission

With your foot off the brake pedal, press and times within 2 seconds. The LED

will

flash 3 times to confirm quick

in

PARK.

release the

0

button 2

stop is entered.

3.

Note: Do not leave children or animals unattended

Remove the keys from the ignition and exit the vehicle. Press the

@

button to lock

the vehicle's doors if desired.

in

the

vehicle

when using the

quick-stop feature.

Operating

The system has the ability

the

Daily

Start

Timer

to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, pressing both the

timer (the vehicle operating the vehicle

@

&

0

buttons together

will

start 24 hours from this time). Next, When you are finished

for the day, perform the following

will

activate the 24 hour countdown

steps to complete the

process.

1.

2.

Turn the ignition

ON/OFF (vehicle must be disarmed).

Within 1 0 seconds,

while pressing the brake, press and

button twice.

3.

Remote

The

Start

vehicle will

Safety

Features

emit 2 chirps and flash

For safety and security reasons, the system

vehicle

starter from activating if any of the following

1.

The

2.

vehicle

The brake

hood is open.

pedal

is pressed prior to turning the

position.

3.

4.

The engine is over-revved (tach checking only). Valet

mode is active.

release

the parking lights 4 times.

will

shutdown or prevent the remote

occur:

ignition key to the

the

ON

0

2012

Audiovox

Electronics

Corporation. All

rights reserved.

7

Transmitter Button Functions

Replacing Remote Control Batteries

CATXMT)

1-Way Remote Control (part

The batteries (model

CR2016) 1 year under normal use. When the batteries become weak you remote control range (the distance from the vehicle the remote control deteriorate and the

small

control batteries:

1 . Remove 3 screws and disassemble the halves of the remote control.

2.

Remove the old batteries, observing the

and replace with new

3.

4.

Reassemble the halves of the remote control and install the 3 screws.

Test operation of the remote control.

#

inside each remote control should last approximately

on the remote control

LED

CR2016 batteries.

will

+1-

dim.

To

symbols

replace the remote

notice the

will

the batteries

on

work)

8 ca5153

5153sst rev A

I

Code Systems, Inc.

Limited

Lifetime

Warranty

Code Systems Inc. ("CODE") warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the "Product"), purchased from provided below) should this Product under normal use and conditions, material or workmanship DURING THE LIFETIME OF THE VEHICLE

be

NALLY INSTALLED, such defect(s) will

repaired or replaced (at CODE's option) without charge

an

authorized CODE dealer, that (except as

be

proven defective

IN

WHICH IT WAS ORIGI-

in

for parts directly related to repairs of the defect(s). Switches, indicator lights, and transmitter cases are similarly warranted to the original purchaser

for a period of one (1) year from the date of purchase of the Product. CODE accessories, sold separately, are covered by the applicable warranty accompanying the

accessory. This warranty is non-transferable, non-assignable and is voided when: (1) the Product is removed

from the vehicle

which it was originally installed; or (2) the vehicle

in

which the Product was

in

originally installed is transferred to another party. This warranty does not apply to any product damaged by accident, physical or electrical abuse,

improper installation, alteration, or use contrary to its intended function, fire, flood, or other natural acts.

In

order for the Product to

be

Product must

returned to sales receipt. The date of purchase and year, make and model of the vehicle was originally installed must

This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED

be

repaired or replaced under the terms of this warranty, the defective

an

authorized CODE dealer and accompanied by a copy of the retail

in

which the Product

be

clearly indicated on the sales receipt.

OR IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL DURATION OF THIS

WRITIEN

WARRANTY.

IN

NO CASE SHALL CODE

BE

LIMITED

BE

LIABLE FOR ANY

TO

THE

CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.

CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT

IS

OF CODE'S LIABILITY UNDER THIS WARRANTY

IN

MENT PROVIDED ABOVE AND,

NO EVENT SHALL CODE'S LIABILITY EXCEED THE PUR-

LIMITED TO THE REPAIR OR REPLACE-

CHASE PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION LABOR.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state

2012

Audiovox Electronics Corporation.

All

rights

reserved.

9

product is covered

This

by

one

or

more

the following U.S. Patents; Other Patents pending.

of

0407,034,0580,160,5,132,660,

5,157,375, 5,193,141, 5,245,694,

5~315,285,

5,334,969

5,349,931' 5,357,560, 5,381,128, 5,412,3711 5,467,070t 5,469,141,. 5,469.151' 5,506,568 5,532,670, 5,534,845, 5,563,576, 5,563,600, 5,572, 185, 5,602,535, 5,614,883, 5,617.819 5,646,591, 5,650,774, 5,656,868, 5,673,017, 5,656,997, 5,712.638, 5,798,711, 5,805,056, 5,819,568, 5,828,316, 5,838,255, 5,850, 5,872,519,

5,898,39t

5,900,806, 5,905,431, 5,907, 195, 5,914,667,

173,

5,783,988, 5,850, 174, 5,855.050 5,945,936, 5,952,933

5,783.989

5,990. 786, 6,028, 732, 6,028,505, 6,040,636, 6,043,734, 6,087,996, 6,093,979, 6,140,914

184,779,

6,

6,218, 7

40, 6,259,

6,462.648, 6,573,838,

6,697,719,

169, 6,285,296,. 6,288,635, 6,317 ,034. 6,452,483, 6,452.484

6,700,479,

6,781

,507, 6,828.901,

6,982,631,

7,030.739 7,069.127, 7,095,314, 7,102,515, 7,135,962, 7,142,097, 7,191,053, 7,243,007, 7,248,150 7,332,998, 7,653,463,

7,443,285, 7,962t260

7,463, 135, 7,483,783,

7,519,400, 7,532,959, 7,616,099,

7,646,285

10 ca5153/5153sst rev A

Audiovox

Electronics Corporation.

Customer

Service

WWW.CODE-ALARM.COM

FCC COMPLIANCE

This device complies with Part 15 of the

1-800-421-3209

FCC

rules and with

RSS-21 0

of

Industry

This device may not cause harmful interference, and

1. This device must accept any interference received, including any interference

2.

Canada. Operation is subject to the

that may cause undesired operation.

Warning!

Changes or modifications not expressly approved by the party responsible for

compliance

12

could

void the user's authority to operate the equipment.

0-192-390

R41

following two conditions:

ca5153

5153sst rev

I

A

WARNING

THIS VEHICLE IS EQUIPPED WITH

A REMOTE

CONTROLLED

CAR

STARTER

BEFORE

SERVICING THIS VEHICLE,

REMOVE THE

MAIN

POWER FUSE

(RED

WIRE) TO

THE CAR

STARTER

OR

DISCONNECT

THE VEHICLE

BATTERY.

LBL0675