Code Alarm CA 4051 Installation Manual

Download

Page 1

PROFESSIONAL

SERIES

Remote St art

Installation Guide

CA 4051

Page 2

Before You Begin ......................................................................................3

Wire Connection Guide ........................................................................... 4

4 Pin Main Harness ................................................................................... 5

3 Pin Parking Light Harness .....................................................................7

6 Pin Start Harness ................................................................................... 8

4 Pin Alternate Harness............................................................................9

2 Pin Door Lock Output Harness ........................................................... 10

Additional Ports ...................................................................................... 11

Antenna / LED / Programming Port ....................................................... 11

DBI Port.................................................................................................... 1 1

Set Up & Programming ..........................................................................12

Transmitter Programming........................................................................ 12

Manual Feature Programming.................................................................12

Programming Feature Banks .................................................................. 13

T ach Programming ..................................................................................14

Smart Tachless Mode .............................................................................14

Feature Descriptions .............................................................................15

Transmitter Button Functions ............................................................. 17

Remote Start Shutdown Diagnostics ................................................17

System Layout .........................................................................................18

Page 3

PROFESSIONAL INST ALLA TION

STRONGLY RECOMMENDED

Installation Precautions:

Roll down window to avoid locking keys in vehicle during installation

Avoid mounting components or routing wires near hot surfaces

Avoid mounting components or routing wires near moving parts

Tape or loom wires under hood for protection and appearance

Technical Support (800) 421-3209

or go to

http://techservices.codesystems.com

Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR "COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle computers.

Use grommets when routing wires through metal surfaces

BEFORE YOU BEGIN

Page 4

6 Pin Start Harness

4 Pin Alternate Output Harness

2 Pin Lock Output Harness

4 Pin Main Harness

3 Pin Parking Light Harness

PURPLE STARTER OUTPUT - MOTOR SIDE

RED BATTERY 12V ( + )

ORANGE ACCESSORY 1 ( + )

PINK/WHITE IGNITION 2 ( + )

RED/WHITE BATTERY 12V ( + )

PINK IGNITION 1 ( + )

6 PIN START

LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )

LT BLUE FACTORY ARM / PULSE AFTER START ( - )

GREEN/WHITE PULSE AFTER SHUTDOWN ( - )

BLACK/YELLOW PULSE DURING CRANK ( - )

4 PIN

ALTERNATE

OUTPUT

Page 5

4 Pin Main Harness

1 BLUE/BLACK IGNITION 3 / ACTIVE OUTPUT ( - )

The Active Output/Ignition 3 output wire provides a ground output when the remote start function is activated and remains until 4 seconds after the remote start is shutdown. The Ignition 3 output wire can be used for several functions listed below. If this wire will be used for multiple application's a 1 amp diode is required in-line with the stripe facing the control module.

Factory transponder (coded key) bypass. General Motors VATS bypass, see the following diagram. Use an SPDT relay (not

supplied). Ignition 3 output, see the following diagram. Use an SPDT relay (not supplied). Accessory 2/3 output, see the following diagram. Use an SPDT relay (not

supplied).

Fused +12 Volt Battery Source

87a

BLUE/BLACK ActiveOutput Wire

VATS Control Module

Matching Value Resistor

Ignition Switch

VATS Wire #1, WHITE or WHITE/BLACK

VATS Wire #2, WHITE or VIOLET/WHITE

X CUT

GM VATS

Fused +12 Volt Battery Source

87a

BLUE/BLACK Active Outpu

Wire

To Vehicle's 2nd or 3rd Ignition Wire

Jump To PINK Ignition Output Wire From Control Module

Ignition 3 Accessory 2/3

Fused +12 Volt Battery Source

87a

BLUE/BLACK Active Outpu

Wire

To Vehicle's 2nd or 3rd Accessory Wire

Jump To ORANGE Accessory Output Wire From Control Module

Page 6

2 PURPLE/WHITE TACH INPUT

Locate the vehicle’s ignition coil or fuel injector in the engine compartment.

Verification: Test using the following procedure:

1. Set voltmeter to AC VOLTS.

2. Attach positive lead of a volt meter to a constant 12-volt source.

3. Attach negative lead of a volt meter to the wire to be tested.

4. Start the engine.

5. Have someone press on the gas pedal slightly as you monitor the meter. If connected to the correct wire, the voltage reading will increase as the engine’s RPM increases.

Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil or fuel injector.

3 GRAY HOOD PIN INPUT ( - )

Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start.

Verification: This wire when connected will register ground when the

vehicle's hood is opened. Connect the GRAY wire to the hood pin. NOTE: Be sure to loom the wire, and seal the grommet.

4 BROWN/RED BRAKE INPUT ( + )

Locate the vehicle’s brake light wire at the brake pedal mounted switch.

Verification: This wire registers positive voltage when the brake pedal is

pressed. Connect the BROWN/RED wire to the vehicle’s brake light wire.

Page 7

1 BLACK GROUND

Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended grounding point is a metal surface in the driver’s side kick panel area.

NOTE: Do not ground the BLACK wire with any other vehicle components.

3 Pin Parking Light Harness

2 WHITE/RED PARKING LIGHT INPUT

3 WHIT E PARKING LIGHT OUTPUT

Locate the parking light output wire at the vehicle’s light switch.

Verification: This wire registers positive voltage when the parking lights are turned on.

Positive switching Parking Lights:

Connect the WHITE/RED wire to a 15 Amp max fused battery source. Connect the WHITE wire to the parking light output wire.

Negative switching Parking Lights:

Connect the WHITE/RED wire to a good chassis ground. Connect the WHITE wire to the parking light output wire.

Page 8

6 Pin Start Harness

1 PURPLE STARTER OUTPUT ( + )

Locate the vehicle starter wire.

Verification: This wire registers voltage only when the key is turned to the START position.

Verification:

The starter wire registers voltage when the key is turned to the START position.

Connect the PURPLE wire to the MOTOR SIDE of the vehicle starter wire.

2 RED BATTERY 12V ( + )

Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage in all positions of the ignition switch.

Connect the RED wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

3 ORANGE ACCESSORY 1 ( + )

Locate the vehicle’s accessory wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to ACC

(Accessory) and the ON (or RUN) position. The voltage drops out when the

key is turned to the START (or CRANK) position. Connect the ORANGE wire to the vehicle’s accessory wire.

4 PINK/WHITE IGNITION 2 ( + )

Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped).

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position, but not the ACC (Accessory) position. The voltage does not

drop out when the key is turned to the START (or CRANK) position. Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire. Programmable output: IGN, ACC, Start.

Page 9

6 PINK IGNITION 1 ( + )

Locate the vehicle’s ignition wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to the ON (or RUN) position. The voltage does not drop out when the key is turned to the

START (or CRANK) position. Connect the PINK wire to the vehicle’s Ignition wire. This wire is also used for Ignition 1 Output.

5 RED/WHITE BATTERY 12V ( + )

Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage in all positions of the ignition

switch. Connect the RED/WHITE wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

4 Pin Alternate Output Harness

1 LT GREEN/BLACK FACTORY DISARM /

PULSE BEFORE ST ART ( - )

This wire will supply a ( - ) 200mA pulse both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door.

Verification: This wire registers ground if the key is turned to the unlock position in the driver’s door cylinder.

Connect the LIGHT GREEN/BLACK wire to the factory alarm disarm wire.

2 L T BLUE FACTORY ARM /

PULSE AFTER START ( - )

This wire will supply a ( - ) 200mA pulse upon a successful completion of the remote start activation sequence and is typically used to re-lock the vehicle’s doors upon remote start if necessary.

Page 10

4 BLACK/YELLOW PULSE DURING CRANK ( - )

Locate the vehicle’s second starter (crank) wire at the ignition switch. (if equipped)

Verification: This wire registers voltage only in the start (crank) position of the ignition switch.

Connect the BLACK/YELLOW wire as shown in the diagram below. Use an SPDT relay (not supplied).

F us ed +1 2 Volt B a ttery S ou rc e

87a

BLACK/YELLOW Pulse During Crank Wire

To Vehic le's 2nd S tarter Wire

Jump To PUR PLE Starter Output Wire From The C ontrol Module

2 Pin Lock Output Harness

1 BLUE UNLOCK ( - )

The door unlock output wire provides an output only while the remote start feature is active.

3 GREEN/WHITE PULSE AFTER SHUTDOWN ( - )

This wire will supply a ( - ) 200mA pulse after the remote start shuts down. This is typically used to re-lock the vehicle’s doors if they unlock upon remote start shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle’s accessories from remaining on after remote start shutdown.

Page 11

Data Bus Interface Port

This 4 pin port is used for Flashlogic Door Lock and Transponder Databus Interfaces to communicate with the vehicle's Databus. When using the DBI port to control the Flashlogic Door Lock and Transponder Interface modules the following options may be available. Please refer to the D2D (Data to Data) function list available per vehicle on the tech service web site.

Tach Input Brake Safety Shut Down Trunk/Hatch Open Diesel Glow Plug Input Door Lock Control Passlock / Passkey Interface (GM Only) Dome Light Supervision Transponder Interface Activation Factory Alarm Arm / Disarm Manual Arm / Disarm Inputs (factory keyless

controls system)

Antenna Port

Mount the supplied antenna/receiver to a clear spot on the vehicle's windshield that will not block the driver's vision. A good location is usually high on the windshield near the rear view mirror. Be careful not to mount the antenna/receiver on any metallic window film, as this will effect system range. Route the antenna/ receiver cable to the control module and plug into the antenna port.

Additional Ports

Page 12

Manual Feature Programming - Feature Bank 2 - 4

1. Turn the ignition ON.

2. Press and hold the valet/override button.

3. Within 10 seconds the parking lights will flash (3) three times.

4. Use the valet/override button to advance through each option bank. For feature programming advance to Feature Bank 2, 3 or 4, which is (4) four, (5) five, and (6) six parking light flashes.

5. Use the transmitter button to scroll through the selections in each feature bank, the parking lights will flash to match the feature number.

6. Press the BRAKE to change the desired feature. The LED will flash indicating the changed feature.

NOTE: The system will remain in feature programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF.

Set Up & Programming

Transmitter Programming - Feature Bank 1

1. Turn the ignition ON.

2. Press and hold the valet/override button.

3. Within 10 seconds the parking lights will flash (3) three times.

4. Press 1 button of each transmitter you wish to program.

5. The system will respond with 1 light flash for each accepted transmitter.

6. Pressing the override button at anytime during programming will advance to the next bank.

NOTE: The system will exit transmitter programming after 15 seconds of inactivity. NOTE: This system has 1 button programming which programs all channels of the

system. NOTE: The system will hold up to 4 transmitters in memory, programming a 5th

transmitter will erase the oldest transmitter in memory. NOTE: This system has PTN - Programmed Transmitter Notification. Each time the

ignition is turned ON, the LED will flash the number of transmitters programmed to the system.

Page 13

Refer to transmitter programming.

Feature set not available on this model.

Feature Bank 1 -

3 Flashes

Transmitter Programming

Feature Bank 2 -

4 Flashes

Security Control

1 LED Flash 2 LED flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash

Feature Bank 3 -

5 Flashes

Output Control

1 LED Flash 2 LED flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash

1 Extended Lock Pulse

1 Second

3.5 Seconds

Double Pulse Unlock

Page 14

Tach Programming

The unit will not operate unless tach is programmed or tachless option is turned ON. If an attempt is made to start the vehicle via the remote start without

first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running in certain instances and reengage the starter motor.

The Remote Start unit will learn the tach rate of most vehicle's single coil, multiple coil

packs, or single injector. To learn tach:

1. Turn the ignition key to the ON position.

2. Press and release the valet/override button 3 times.

3. Immediately turn the ignition key OFF.

4. Press and hold the valet/override button, then start the vehicle using

the key.

5. When the unit senses the tach signal, the parking lights will begin to

flash.

6. Allow the vehicle to settle to a normal idle speed.

7. Release the valet/program push-button switch. The parking lights will

stay on solid indicating that the learned tach signal is stored and the unit has exited tach learn mode.

NOTE: If the unit fails to learn tach rate due to an improper tach connection or a poor tach source, the parking lights will not flash. To correct this situation, locate and connect the PURPLE/WHITE wire to the proper tach signal, and then repeat

the tach learn routine.

Smart Tachless Mode

Smart Tachless Mode is available only if a tach signal has never been learned to the system and when activated will automatically change the Tach Mode feature in option programming to Tachless without the need to enter the feature programming mode.

1. Activate the remote start. The parking lights should begin flashing 7

times indicating no tach signal has been learned.

2. Within the 7 flash time period, press and hold the button.

3. One extended parking light flash (1.5 seconds) will indicate the

system is now in tachless mode.

Page 15

Feature Bank 2 - Security

Feature set not available on this model.

Feature Descriptions

Feature Bank 3 - Output Control

1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock

output wires.

1 Second - Single 1 second unlock pulse.

3.5 Seconds - Single 3.5 second unlock pulse. Double Pulse Unlock - Double 1 second unlock pulse.

Feature Bank 4 - Remote Start Control

2 - Run Time: Controls the time in minutes that the vehicle will stay running

under control of the remote start until the system times out. The system may also be shut down at any time by use of the transmitter or system shutdowns.

3 - Running Lights: Controls the WHITE parking light output wire during remote start.

Steady - Parking lights constant during the remote start cycle. Flashing - Parking lights flash at a slow pace during the remote start cycle.

4 - Tach Mode: Determines how the system monitors the engine running during remote start.

Tach - Hard wired directly to the tach wire of the vehicle to monitor AC voltage.

Tachless (Crank Average/Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key and then monitors the change in voltage after remote start.

Hybrid (Crank Average / No Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key.

DBI Port - Monitors the vehicle’s tach rate through an interface module connected to the DBI port.

Page 16

5 - Voltage Level: The voltage variance for remote start when set to tachless. (see tach mode)

HIGH - The variance in battery voltage from before the remote start is activated to after the engine is running must be greater than 0.5 volts.

LOW - The variance in battery voltage from before the remote start is activated to after the engine is running may be less than 0.5 volts.

6 - Crank Time: Preset output times for the PURPLE starter wire.

1 Second 0.8 Seconds 1.5 Seconds 2 Seconds 4 Seconds

7 - Crank Average / Crank Time: The length of time in which the remote start will crank the vehicle’s starter.

Crank Average - Determines crank time by averaging the last 8 times the vehicle was started with the key.

Preset Time - Preset starter output time. (see crank time)

8 - Gas / Diesel: Selects engine type and delay time for the starter output wire during remote start activation.

Gas - Gasoline engine, no delay for the starter output wire. 10 Second Delay - Diesel engine, delays the starter output wire for 10

seconds after the ignition has been powered up by the remote start. 15 Second Delay - Diesel engine, delays the starter output wire for 15

seconds after the ignition has been powered up by the remote start. 20 Second Delay - Diesel engine, delays the starter output wire for 20

seconds after the ignition has been powered up by the remote start. 45 Second Delay - Diesel engine, delays the starter output wire for 45

seconds after the ignition has been powered up by the remote start.

9 - Single / Double Pulse Start: Switches the remote start activation between a single or double press from the transmitter.

10 - IGN 2 Output: Programmable high current output.

Ignition 2 - Ignition output during remote start. Accessory - Accessory output during remote start. Start / Crank - Crank output during remote start.

11 - 2 or 3 Hour Start: When activated, the remote start will activate and run for the programmed time and shut down every 2 or 3 hours.

Page 17

Transmitter Button Functions

Remote Start Shutdown Diagnostics

If the remote start shuts down or fails to start, the parking lights will flash one of the patterns below indicating the shutdown input.

To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and hold the button for 3 seconds.

FLASHES TRIGGER ZONE

3 Flashes Hood Input

Brake Input

4 Flashes Remote St art Valet Mode 7 Flashes Tach not learned / Crank Average not learned

1 Button Transmitter Start / Aux Operation Method

Unlock X

Press and Hold - During remote start only

Remote Start X

Press and Release (1 or 2 times depending on selectable option)

Remote Start Shut Down

Press and Release (1 or 2

times depending on

selectable option)

Page 18

BLACK/YELLOW PULSE DURING CRANK ( - )

GREEN/WHITE PULSE AFTER SHUTDOWN ( - )

LT BLUE FACTORY ARM / PULSE AFTER START ( - )

LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )

BLUE UNLOCK ( - )

OPEN

PURPLE STARTER OUTPUT - MOTOR SIDE ( + )

RED BATTERY 12V ( + )

ORANGE ACCESSORY 1 ( + )

PINK/WHITE IGNITION 2 ( + )

RED/WHITE BATTERY 12V ( + )

PINK IGNITION 1 ( + )

BLACK GROUND

WHITE/RED PARKING LIGHT INPUT

WHITE PARKING LIGHT OUTPUT

BLUE/BLACK IGNITION 3 / ACTIVE OUTPUT ( - )

PURPLE/WHITE TACH INPUT

GRAY HOOD INPUT ( - )

BROWN/RED BRAKE INPUT ( + )

ANTENNA

LED

VALET

DBI PORT

CA 4051

Page 19

Page 20

Audiovox Electronics Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference that may cause undesired operation.

Warning!

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.