Code 3 XT3 User Manual

XT3 / XT4 / XT6 - LED LIGHT HEADS

AVAILABLE LED COLORS - Red, Amber, Blue, White and Green

XT3 SINGLE
LED COLOR

SCREWS

WARNING!

XT4 DUAL

LED COLOR

XT3A
XT3B
XT3G
XT3R

XT3W

BEZEL

This Product contains high intensity LED

devices. To prevent eye damage, DO NOT
stare into light beam at close range.

XT4AA XT4RA
XT4AW XT4RB
XT4BA XT4RR
XT4BB XT4RW
XT4BW XT4WW
XT4GG

LIGHT HEAD

XT4 MULTI

LED COLOR

BEZEL
GASKET

XT4MCAW

XT4MCBA

XT4MCBW

XT4MCRA
XT4MCRB

XT4MCRW

WIRING INSTRUCTIONS:
RED ----------To +VDC (fuse @ 2A)
BLACK ------To Chassis Ground
BLUE --------Flash Pattern Select (see list at right)
YELLOW ---Connect YELLOW wires of all heads
together for Synchronization. Note: Only like
products may be syncronized.

*When the Yellow wires of all heads are connected to-

gether, the Group1 heads will ash either in phase (P1)
or 180 degrees out of phase (P2) based on the pattern

selected. For example, if the XT3 lights in Group1 have

pattern PA1, A1-Five Flash P1 selected and the Group2
heads have pattern PA2, A2-Five Flash P2 selected, the
Group1 / Group2 heads will ash in a Five Flash Alter-

XT6 DUAL

LED COLOR

XT6AA XT6RA
XT6AW XT6RB
XT6BA XT6RR
XT6BB XT6RW
XT6BW XT6WW
XT6GG

XT6 MULTI

LED COLOR

XT6MCBA

XT6MCBW

XT6MCRA
XT6MCRB

XT6MCRW

TO SELECT FLASH PATTERNS:

Touch BLUE wire to BLACK wire:

- less than 1 second for next pattern

- more than 1 second for previous pattern

- more than 5 seconds to turn off

FLASH PATTERNS - SINGLE COLOR: XT3

PA1- A1 - Five Flash P1 PA7- A7 - Single Flash P1
PA2- A2 - Five Flash P2 PA8- A8 - Single Flash P2
PA3- A3 - Quad Flash P1 PA9- A9 - Triple Flash P1
PA4- A4 - Quad Flash P2 PA10- A10 - Triple Flash P2
PA5- A5 - Double Flash P1 PA11- A11 - Steady Burn
PA6 - A6 - Double Flash P2 PA12- OFF

FLASH PATTERNS - DUAL COLOR: XT4 / XT6

PA1- Single Alert Alternating PA9- Single Flash75 Simultaneous P2 PA17- Action Scan
PA2- Single Alert Simultaneous P1 PA10- Single Flash375 Alternating PA18- Steady with 5 Single & Single POP
PA3- Single Alert Simultaneous P2 PA11- Single Flash375 Simultaneous P1 PA19- Steady – 5 Single
PA4- Fast Flash Alternating PA12- Single Flash375 Simultaneous P2 PA20- Steady
PA5- Fast Flash Simultaneous P1 PA13- Action Flash Alternating PA21- Cycle Flash(factory Default)- AUTORUN
PA6- Fast Flash Simultaneous P2 PA14- Action Flash Simultaneous PA22- OFF
PA7- Single Flash75 Alternating PA15- Modul Flash Alternating
PA8- Single Flash75 Simultaneous P1 PA16- Modul Flash Simultaneous

FLASH PATTERNS - MULTI COLOR: XT4 / XT6

PA1 - LAMP-1 Single Flash 75 Sim P1(Factory Default) PA14 - LAMP-2 Double Flash 75 Sim P2
PA2 - LAMP-1 Single Flash 75 Sim P2 PA15 - Dual-Lamp ALT Double Flash 75 Sim P1
PA3 - LAMP-2 Single Flash 75 Sim P1 PA16 - Dual-Lamp ALT Double Flash 75 Sim P2
PA4 - LAMP-2 Single Flash 75 Sim P2 PA17 - Dual-Lamp ALT Quad Flash 75 Sim P1
PA5 - LAMP-1 CA T13 75FPM Single Flash Sim P1 PA18 - Dual-Lamp ALT Quad Flash 75 Sim P2
PA6 - LAMP-1 CA T13 75FPM Single Flash Sim P2 PA19 - LAMP-1 ECE R65 120FPM Single Flash Sim P1
PA7 - LAMP-2 CA T13 75FPM Single Flash Sim P1 PA20 - LAMP-1 ECE R65 120FPM Single Flash Sim P2
PA8 - LAMP-2 CA T13 75FPM Single Flash Sim P2 PA21 - LAMP-2 ECE R65 120FPM Single Flash Sim P1
PA9 - Dual-Lamp ALT Single Flash 75 Sim P1 PA22 - LAMP-2 ECE R65 120FPM Single Flash Sim P2
PA10 - Dual-Lamp ALT Single Flash 75 Sim P2 PA23 - Dual-Lamp ALT ECE R65 120FPM Single Flash Sim P1
PA11 - LAMP-1 Double Flash 75 Sim P1 PA24 - Dual-Lamp ALT ECE R65 120FPM Single Flash Sim P2
PA12 - LAMP-1 Double Flash 75 Sim P2 PA25 - OFF
PA13 - LAMP-2 Double Flash 75 Sim P1

WARRANTY

Code 3, Inc.’s emergency devices are tested and found to be operational at the time of manufacture. Provided
they are installed and operated in accordance with manufacturer’s recommendations, Code 3, Inc. guarantees all
parts and components except the lamps to a period of 1 year, LED Lighthead modules to a period of 5 years (unless
otherwise expressed) from the date of purchase or delivery, whichever is later. Units demonstrated to be defective
within the warranty period will be repaired or replaced at the factory service center at no cost.

Use of lamp or other electrical load of a wattage higher than installed or recommended by the factory, or use
of inappropriate or inadequate wiring or circuit protection causes this warranty to become void. Failure or destruction
of the product resulting from abuse or unusual use and/or accidents is not covered by this warranty. Code 3, Inc.
shall in no way be liable for other damages including consequential, indirect or special damages whether loss is due
to negligence or breach of warranty.

CODE 3, INC. MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY INCLUDING, WITHOUT LIMITA­TION, WARRANTIES OF FITNESS OR MERCHANTABILITY, WITH RESPECT TO THIS PRODUCT.

NEED HELP? Call our Technical Assistance HOTLINE - [phone]

PRODUCT RETURNS

If a product must be returned for repair or replacement*, please contact our factory to obtain a Return Goods
Authorization Number (RGA number) before you ship the product to Code 3, Inc. Write the RGA number clearly on

the package near the mailing label. Be sure you use sufcient packing materials to avoid damage to the product

being returned while in transit.

*Code 3, Inc. reserves the right to repair or replace at its discretion. Code 3, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or reinstallation of
products requiring service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of products returned to sender after the service has been rendered.

Code 3 is a registered trademark of Code 3, Inc. a Public Safety Equipment Company.

Code 3®, Inc.

St. Louis, Missouri 63114-2029—USA

Ph. [phone] Fax [phone]

Revision 1, 10/12 - Instruction Book Part No. T11619

©2012 Public Safety Equipment, Inc. Printed in USA

10986 N. Warson Road

www.code3pse.com