Code 3 Work Light - 9 LED User Manual

!

Installation and Operation Instructions

CW2310 & CW2311 LED WORKLAMPS

Code 3’s CW2310 and CW2311 LED Worklamps feature nine
10-watt LEDs that produce an extremely high-intensity beam as
well as an aluminum heatsink housing, heavy-duty stainless steel
mounting bracket and tough polycarbonate lens to withstand the
most demanding applications. These highly durable worklamps
are designed to perform in the harshest of work environments and
offer all the benefi ts of LED technology including the brightest white
light output, a long, maintenance-free service life and extremely low

current consumption.

IMPORTANT! Read all instructions before installing and using. Installer: This manual must be

delivered to the end user.

WARNING!

Failure to install or use this product according to manufacturer’s recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!

Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.

1. Proper installation combined with operator training in the installation, use, care and maintenance of vehicle equipment accessories is
essential to ensure the safety of you and those you are trying to protect.

2. Exercise caution when working with live electrical connections.

3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high
current arcing, which can cause personal injury and/or severe vehicle damage, including fi re.

4. Proper placement and installation are vital to the performance of this worklamp. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he can

operate the system without losing eye contact with the work area.

5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the
vehicle operator should ensure the projection of the beam is not blocked by vehicle components (i.e., open trunks
or compartment doors), people, vehicles, or other obstructions.

6. The manufacturer assumes no liability for any loss resulting from the use of this device.

SAA

NOTE: Black die cast Aluminum housing gets very hot to the touch after operating constantly for several hours.

Speci cations:

Voltage: CW2310: 12-24 VDC
CW2311: 12-24 VDC

Current: CW2310: 5.3 Amps @ 12.8VDC
CW2311: 5.3 Amps @ 12.8VDC

Weight: CW2310: 4.7 lbs.
CW2311: 4.7 lbs.

Lumens: CW2310: 5050(Raw), 3600(Effective)
CW2311: 4950(Raw), 3600(Effective)

Installation:

1. Select a mounting location for the unit on a fl at surface.
Place the unit bracket, fl at side down, on the surface.

2. Use the two circular slots in the bracket to mark the drill
locations for mounting. Drill two 0.397 diameter through holes
(X drill bit) through the mounting surface. Align the base with
the mounting holes, and use 3/8”-16 hardware (include bolts,
fl at washers, lock washers, and nuts) to mount the bracket to
the surface. Position the unit in the horizontal direction, and

tighten both nuts.

3. To position the unit vertically, use a 5/32” hex L-key to
loosen the two screws on each side of the bracket. Tighten
the screws when pivoted properly.

920-1005-00 Rev. A

Page 1 of 2

Wiring Instructions:

Black Wire: Ground
Red Wire: Connect to fused power

See wiring diagram for further instruction

Worklamp

Switch

User Supplied

BLKRED

Ground

Fuse 7.5A

User Supplied

Ground

Manufacturer Limited Warranty and Limitation of Liability:

Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specications for this product (which are available from the
Manufacturer upon request), and Manufacturer further warrants that this product is free from defects in materials and workmanship. This Limited Warranty
extends for 36 months from the date of purchase. Other warranties may apply, call Manufacturer for details. Manufacturer will, at its discretion, repair or
replace any product found by the Manufacturer to be defective and subject to this Limited Warranty.

DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR
OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET

FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.

ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT WHICH MAY HAVE BEEN MADE BY SALESPEOPLE, DEALERS, AGENTS OR OTHER
MANUFACTURER’S REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES. THIS LIMITED WARRANTY MAY NOT BE AMENDED, MODIFIED, OR EN­LARGED EXCEPT BY A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICIAL OF MANUFACTURER WHICH EXPRESSLY REFERS TO THIS LIMITED

WARRANTY.

Exclusion of Other Warranties: MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES

FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT. BUYER’S SOLE
AND EXCLUSIVE REMEDY IN CONTRACT, TORT, OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE

SHALL BE THE REPLACEMENT OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE.

Limitation of Liability: IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM

RELATED TO THE MANUFACTURER’S PRODUCTS, MANUFACTURER’S LIABILITY FOR DAMAGES SHALL BE LIMITED TO THE AMOUNT PAID FOR THE

PRODUCT AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE

EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH
OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE
PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGA­TION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.

This Limited Warranty denes specic legal rights. You may have other legal rights which vary from state to state. Some states do not allow the exclusion or
limitation

10986 North Warson Road

St. Louis, MO 63114

Customer Service

[phone]

[e-mail]

www.code3esg.com

A Division of ESG | www.eccogroup.com

©2014 CODE 3

920-1005-00 Rev. A Page 2 of 2