It is not against federal law to receive radar transmissions with your Cobra radar/
laser detector. The Communications Act of 1924 guarantees your right to receive
radio transmissions on any frequency. Local laws that contravene this Act, while
illegal, may be enforced by your local law enforcement officials until and unless
they are prohibited from doing so by federal court action.
Safety Alert
Use of this product is not intended to, and does not, ensure that motorists or passengers
will not be involved in traffic accidents. It is only intended to alert
the motorist that an emergency vehicle equipped with a Cobra Safety Alert
transmitter is within range as defined by that product. Please call local fire
and police departments to learn if coverage exists in your area.
Safe Driving
Motorists, as well as operators of emergency or service vehicles, are expected to exercise
all due caution while using this product, and to obey all applicable traffic laws.
Security of Your Vehicle
Before leaving your vehicle, always remember to conceal your radar detector
in order to reduce the possibility of break-in and theft.
•
Nothing Comes Close to a Cobra
14 BAND™
ULTRA-HIGH PERFORMANCE
DIGITAL RADAR/LASER DETECTOR
Allows you to adjust the UltraBright
Data Display brightness for easy
reading. (Also turns VG-2 and
Spectre I & IV+ alerts On and Off.*)
* Press and hold for four seconds to
access these functions.
English
A2
For manual mute or auto
mute of audio alerts. (Also
turns Voice Alert On and Off.*)
Speaker
Mute Button
Mount
LaserEye
For 360° detection
of laser signals.
Audio Jack
City Button
For City or Highway
modes to reduce false
alerts. (Also turns Ku
IntelliMute Button
Engine RPM sensing mute function
which reduces false alerts. Button
turns IntelliMute On and Off. (Also
enters IntelliMute setting mode.*)
WARNING
Modifications or parts substitutions not approved
by Cobra Electronics Corporation may violate
FCC Rules and void your authority to operate
this equipment.
alerts On and Off.*)
•
Display
•
NOTE: In This Manual
X K Ka V S L
When steady,
the display will
X K KaVS c
be shown:
Radar, VG-2,
Spectre I & IV+ and
Safety Indicators
and IntelliMute Pro
Signal Strength 1 (weakest) to 5 (strongest)
Mode Indicators
Signal
Strength,
Pop, Laser,
City/Highway
Product Features
IntelliMute
Indicator
When blinking,
the display will
be shown:
X & K will light
simultaneously
when indicating
Ku detection:
X K Ka VS c
XK Ka VS c
Congratulations! You’ve made a smart choice by purchasing a high
performance radar/laser detector from Cobra. Just look at some of
the sophisticated features and capabilities your new unit includes:
Xtreme Range
Superheterodyne
®
Technology
With super-fast sweep circuitry,
provides extra detection range
and the best possible advance warning
to even the fastest radar guns
Detection and Separate Alerts For:
Radar signals (X, K, Ka and Ku bands,
with signal strength indicated), Laser
signals, Safety Alert signals, VG-2
signals, Spectre I & IV+ signals
®
LaserEye
For 360° detection of laser signals
Instant-On Ready
Detects radar guns with “instant-on”
(very fast) speed monitoring capabilities
Pop Detection
Detects the latest super-fast instant-on
single pulse radar guns
Tone Alert or Voice Alert
®
With adjustable volume
This booklet describes the simple steps for mounting and setting up your detector. It also provides helpful
information about how radar and laser guns are used and how you can interpret the alerts you receive.
UltraBright™ Data Display
Easy-to-read with adjustable brightness
City or Highway
Modes to reduce false alerts
Alert Programming
Easy setting of radar bands to be monitored
Safety Alert®
Traffic warning system distinguishes
important safety alerts from other
K band signals
Manual Mute or Auto Mute
A mute function of audio alerts
IntelliMute
®
A mute function reduces false audio alerts
by sensing engine RPMs
IntelliMute
®
Pro
Prevents detection by radar detector detectors
(RDDs) when traveling at slower speeds
Mounting
Mounts easily on windshield or dashboard
Nothing Comes Close to a Cobra
®
A3
Trademark Acknowledgement
Cobra®, DigiView®, EasySet®, Extra Sensory Detection®, IntelliMute®, IntelliMute® Pro, IntelliShield®,
•
LaserEye®, Nothing Comes Close to a Cobra®, Safety Alert® Trafc Warning System, Strobe Alert®,
VG-2 Alert®, Xtreme Range Superheterodyne® and the snake design are registered trademarks of Cobra
Electronics Corporation, USA.
Cobra Electronics Corporation™, 14 Band™, 15 Band™, AURA™, Extreme Bright DataGrax™,
IntelliLink™, IntelliScope™, IntelliView™, Revolution™ Series, SmartPower™, Super-Xtreme Range
Superheterodyne™, S-XRS™, UltraBright™, and Voice Alert™ are trademarks of Cobra Electronics
Corporation, USA.
Opticom™ is a trademark of 3M Corporation. Instaclear® for Ford is a registered trademark of Ford
Motor Company, Inc. Electriclear® for GM is a registered trademark of General Motors Corporation.
LTI Laser™ and LTI 20-20™ are trademarks of Laser Technology, Inc. Kustom Laser™, Kustom Laser
340™ and ProLaser II™ are trademarks of Kustom Signals, Inc. SpeedLaser™ is a trademark of Laser
Atlanta. Bee III™ and Pop™ are a trademarks of MPH Industries. Stalker™ LIDAR is a trademark of
Applied Concepts, Inc. Spectre I™ and Spectre IV™ are trademarks of Stealth Micro Systems Pty. Ltd.
SpeedLaser™ is a trademark of Laser Atlanta, LLC. Interceptor VG-2™ is a trademark of TechniSonic
Industries LTD. Tomar® is a registered trademark of TOMAR Electronics, Inc.
Nothing Comes Close to a Cobra
®
25
Introduction
Contents
Introduction
Important Information ...................................................................................... A1
You will get optimum performance from your detector if you Mount it at a
point approximately in the center of the vehicle, as low as possible on the front
windshield without obstructing the unit’s view of the road either to
the front or rear. Make sure the unit is level with the road. You can also
mount it directly on the dashboard.
Windshield MountingDashboard Mounting
The unit’s lens must not be blocked and the LaserEye should have a clear view
out the back window to allow 360° detection.
The LaserEye Should Have a Clear View
Radar and laser
signals pass
through glass but
not through other
materials and
objects. Objects
that can block or
weaken incoming signals include:
g
Windshield wiper blades
g
Mirrored sun screens
g
Dark tinting at the top of the windshield
g
Heated windshields currently available on some vehicles
(Instaclear for Ford, Electriclear for GM.) Consult your dealer
to see if you have this option.
•
Windshield Mounting
1. Attach the rubber
cups to the bracket.
2. Make sure the rubber cups and your windshield are clean.
3. Push the bracket firmly onto
the windshield.
4. Attach the detector to
the bracket. Check the
angle of the unit.
5. To adjust the angle if
necessary, gently push or
pull on the bracket to bend
it. DO NOT use the detector
to bend the bracket.
6. Plug the power cord
into the detector.
7. Plug the cigarette lighter
adapter on the power
cord into your vehicle’s
cigarette lighter.
8. You can temporarily remove the detector whenever you
wish by pressing the bracket release button and sliding
it off the bracket.
2
English
Nothing Comes Close to a Cobra
®
3
Your Detector
Installation
Your Detector
Getting Started
Dashboard Mounting
1. Place the detector on the dashboard to find a location
where the unit has a clear, level view of the road.
The angle can NOT be adjusted after mounting.
2. Remove the paper backing
from one side of the hookand-loop fastener.
3. Attach the pad to the
dashboard at your chosen
location and remove the
other paper backing.
4. Attach the detector to the
hook-and-loop fastener.
You can remove and reattach
the unit as
often as you like.
5. Plug the power cord
into the detector.
6. Plug the cigarette lighter
adapter on the power
cord into your vehicle’s
cigarette lighter.
Getting Started
Power On
X K Ka V Sh
On-Off/
Volume Control
Rotate clockwise
(away from you)
To Turn On the Unit and Adjust the Audio Volume
Rotate the On-Off/
Volume control
clockwise (away
from you).
ToneVoice
Three beepsTesting, then
three beeps
System Ready, then
Visual Display
h
appears in the
display indicating
that the power
is On
Voice Alert
NOTE
In some vehicles, power is supplied to the cigarette lighter even while the ignition
is Off. If this is the case with your vehicle, you should turn Off or unplug your
detector when parking for lengthy periods.
Auxiliary Audio Jack
The Auxiliary Audio Jack can be used to connect external speakers in
environments with high ambient noise levels. (This uses a mini stereo audio
connector.)
•
•
4
English
Auxiliary
Audio Jack
Nothing Comes Close to a Cobra
®
5
Your Detector
Settings
Your Detector
Settings
Settings
When changing the Settings on your detector, please keep in mind:
g
Buttons can have multiple functions.
g
Depending on your choice of Voice Alert or Tone Alert mode, you will
hear either voice messages or tones confirming changes in settings.
g
All settings will be stored in memory when the power is
turned Off and recalled when the power is turned back On.
Highway/City Mode
Setting your detector to City mode delays all X band audio alerts until
the signal strength reaches Level 3. (A single beep will sound when the
signal is first detected.) This will reduce false alerts while you are driving
in, or near, urban areas where there are many sources for conflicting
X band signals such as microwave towers and automatic door openers.
To change settings, follow the procedure listed below, which indicates
what you will see and hear (either in Voice Alert or Tone Alert mode)
as you complete each step. The factory setting is Highway mode.
Press and
X K Ka V S h
City Mode
X K Ka V S
To Change From Highway Mode to City Mode
Press and release
the City button.
To Change From City Mode Back to Highway Mode
Press and release
the City button again.
c
ToneVoice
One beepCity
ToneVoice
Two beepsHighway
release
Visual Display
c
appears
in the display
Visual Display
h appears
in the display
•
UltraBright Data Display Brightness
You can choose from three settings for Brightness of the display.
You can cycle through the settings by repeatedly pushing the Dim button.
The factory setting is Bright.
Bright
Press and
release Dim
Dark
button
Dim
Dim Button
Press and release
To Change the Brightness to Dim
Press and release
the Dim button once.
To Change the Brightness to Dark
Press and release
the Dim button
again.
To Change the Brightness to Bright
Press and release
the Dim button a
third time.
ToneVoice
One beepDimDisplay dims
ToneVoice
One beepDarkDisplay remains dim
ToneVoice
Two beepsBrightDisplay returns
Visual Display
Visual Display
(no visual alerts will
be seen)
Visual Display
to full brightness
6
English
Nothing Comes Close to a Cobra
®
7
Your Detector
Settings
Your Detector
Settings
Muting an Alert
Your detector allows you to quickly turn Off an audio Alert by momentarily
pressing the Mute button. If you press the Mute button a second time
during the Alert, the audio Alert will be turned back On.
Auto Mute Mode
Auto Mute will automatically reduce the audio volume of all alerts
after four seconds for as long as the signal is detected. The factory
setting for Auto Mute is On.
Mute Button
Press and release
To Turn Auto Mute On
Press and release
the Mute button
again while no
alert is occurring.
To Turn Auto Mute Off
Press and release
the Mute button
while no alert
is occurring.
ToneVoice
Two beepsAuto Mute OnNone
ToneVoice
One beepAuto Mute OffNone
Visual Display
Visual Display
IntelliMute
IntelliMute is a unique feature that allows you to avoid alerts you don’t need to
hear because you are stopped or moving slowly. By sensing the “revs” (RPMs)
of your engine, IntelliMute knows when you are at low speed and automatically
mutes audio radar alerts.
Before IntelliMute will work, you must set an activation point for your engine’s
revs (see page 10 for initial setup). Whenever the revs are below that point,
IntelliMute will begin muting. The activation point will be stored in memory and
recalled each time the power is turned On. The factory setting is IntelliMute Off.
NOTE
IntelliMute may not work with some vehicles because it cannot sense the
engine’s revs. In such cases, you can reduce unwanted audio alerts by
using Auto Mute and City mode when appropriate.
IntelliMute Button
Press and release
To Turn IntelliMute On
Press and release
the IntelliMute
button.
To Turn IntelliMute Off
Press and release
the IntelliMute
button again.
ToneVoice
Two beepsIntelliMute OnDot appears next to
ToneVoice
One beepIntelliMute OffDot disappears
Visual Display
the large character
on the right
Visual Display
8
English
Nothing Comes Close to a Cobra
®
9
Your Detector
Settings
What to Remember While Using IntelliMute
IntelliMute works with both City and Auto Mute modes.
Whenever your engine revs are below the activation point, the dot next to
the large character on the right side of the display will remain lit. Above the
activation point, the dot will blink twice every two seconds.
Below Activation Point
Above Activation Point
Your Detector
Settings
IntelliMute Button
Press and release
X K Ka V S
c
X K Ka V S
c
If, for any reason, the unit stops sensing your engine’s revs, IntelliMute
will indicate an error and automatically turn Off.
The rev point you set will be stored in the unit’s memory when power is turned
Off and recalled each time the power is turned On.
NOTE
The rev point must be reset if you use your detector in a different vehicle.
NOTE
When initially choosing your IntelliMute activation point, a setting
of approximately 300 to 600 RPMs above idle is recommended.
You can reset the activation point at any time to fit your individual
preferences and driving style.
Setting the IntelliMute Activation Point
Your detector must be installed in your vehicle.
CAUTION
Do not attempt to set the rev point while driving.
Your vehicle should be parked and idling.
IntelliMute must be turned On before setting the activation point. Depending on
whether the unit is in Tone Alert or Voice Alert mode, you will hear a series of
beeps or voice messages as you follow the steps on the next page.
To Set the IntelliMute Activation Point
Press and hold
the IntelliMute
button for two
seconds.
Rev your engine to
the level you wish
to set (recommend
slightly above idle)
and hold revs steady
for two seconds.
At the desired
rev level, press
and release the
IntelliMute
button.
Tone
Two beepsSet Engine RevsNone
NoneNoneThree bars will
Three beepsIntelliMute Set All three bars flash
NOTE
If the unit is unable to sense usable pulses within three
seconds or if you do not set a rev point within 20 seconds
of beginning these steps, IntelliMute will indicate an error
and automatically turn Off.
Tone
Four beepsIntelliMute Error,
Voice
Voice
followed by
IntelliMute Off
Visual Display
flash in succession
123
three times
123
Visual Display
E appears
X K Ka V S E
10
English
Nothing Comes Close to a Cobra
®
11
Your Detector
Settings
Your Detector
Settings
IntelliMute Pro
IntelliMute Pro prevents detection by radar detector detectors (RDDs) such as
VG-2, Spectre I and Spectre IV+ when traveling at slower speeds. It is intended
for use by experienced users only.
When IntelliMute Pro is turned On, and engine RPMs are below the IntelliMute
activation point, your detector’s radar detection circuits are turned Off to prevent
detection by RDDs.
Before IntelliMute Pro can be turned On, you must have turned On and Set the
IntelliMute activation point. (See pages 9 through 11.)
CAUTION
When IntelliMute Pro is On, NO radar signals will be detected and
NO alerts will be given at RPMs below the IntelliMute activation point.
IntelliMute Button
City Button
Press and hold both
buttons simultaneously
IntelliMute Pro On
X K KaV S
To Turn IntelliMute Pro On
While no signal
is being detected,
press and hold both
the IntelliMute
and City buttons
for four seconds.
To Turn IntelliMute Pro Off
Press and hold both
the IntelliMute andCity buttons for
four seconds.
English
12
ToneVoice
Two beepsIntelliMute Pro On c or h will blink
ToneVoice
One beepIntelliMute Pro Off c or h will show
Visual Display
Visual Display
steady
Voice/Tone Setting
You can set your detector to sound alerts with either a Voice or a Tone. You can
change settings by using the Mute button. In Voice Alert mode, you will first hear
several tones, then a voice message announcing the type of signal detected,
followed by more tones. In Tone Alert mode, you will hear the tones only. The
factory setting is Voice Alert mode.
To Change From Voice Alert to Tone Alert
While no signal
is being detected,
press and hold
the Mute button
for two seconds.
To Change From Tone Alert Back to Voice Alert
While no signal
is being detected,
press and hold the
Mute button for
two seconds again.
c
VG-2 and Spectre I & IV+ Alert Settings
Police use radar detector detectors (RDDs) to spot users of radar detectors.
Your detector is able to identify signals from VG-2, Spectre I and Spectre IV+
RDDs and can provide alerts when any of these or similar devices are in use
near your vehicle.
Your detector can be spotted by Spectre IV+ RDDs, but is invisible to VG-2 and
Spectre I RDDs. You can choose whether you want to be alerted to VG-2 and
Spectre I & IV+ RDD signals. The factory setting for VG-2 and Spectre I & IV+
alerts is Off.
To Turn VG-2 and Spectre I & IV+ Alerts On and Off
While no signal
is being detected,
press and hold the
Dim button for
four seconds.
ToneVoice
One beepTone AlertNone
ToneVoice
NoneVoice AlertNone
ToneVoice
On = Two BeepsSpectre VG-2 On
Off = One Beep
Spectre VG-2 Off
Nothing Comes Close to a Cobra
Visual Display
Visual Display
Visual Display
V will blink twice
in the display
V will blink once
in the display
®
13
Your Detector
Settings
Your Detector
Settings and Detection
Radar Alert Settings
The detector allows you to choose whether it will show alerts on the X, K
and Ku bands. The factory settings are: X Band and K Band On; Ku Band Off.
To Turn X Band On and Off
While no signal is
being detected, press
and hold both the Dim
and Mute buttons for
four seconds.
To Turn K Band On and Off
While no signal is
being detected,
press and hold both
the Mute and City
buttons for four
seconds.
To Turn Ku Band* On and Off
While no signal is being
detected, press and
hold the City button
for four seconds.
ToneVoice
X On = Two beeps
X Off = One beep
ToneVoice
K On = Two beeps
K Off = One beep
ToneVoice
Ku On = Two beepsKu On
Ku Off = One beep
X On
X Off
K On
K Off
Ku Off
Visual Display
X will blink twice
in the display
X will blink once
in the display
Visual Display
K will blink twice
in the display
K will blink once
in the display
Visual Display
X and K will blink
twice in the display
X and K will blink
once in the display
Pop Alert
The Pop Mode Radar Gun is a single-pulse Doppler radar that is a feature
of a K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses
a single, short-time pulse to measure the target vehicle’s speed.
The Pop mode receiver senses Pop singles beyond the effective range of Pop
radar guns. As the Pop mode receiver is so sensitive, you should limit the use
of Pop Detect mode to highway and rural driving.
Pop Alert will alert you to Pop radar signals. During the alert, the unit
continues to detect other signals. The factory setting is Pop Detect Off.
Pop Alert (continued)
To Turn Pop Alert On and Off
While no signal is
being detected,
press and hold both
the Dim and City
buttons for four
seconds.
To Turn Safety Alert On and Off
While no signal
is being detected,
press and hold
the Dim and iMute
buttons for
four seconds.
ToneVoice
Pop On = Two beeps
Pop Off = One beep
Tone
On = Two beeps
Off = One beep
Pop On
Pop Off
Voice
Safety Alert On
Safety Alert OffS Flashes One Time
Visual Display
P will blink twice
in the display
P will blink once
in the display
Visual Display
S Flashes Two Times
Detection
The tables on the following pages show you the types of Signals your detector
will detect, as well as the voice and visual alerts it provides for each of them.
In Voice Alert mode you will first hear several tones, then a voice message
announcing the type of signal detected, followed by more tones. In Tone Alert
mode, you will hear the tones only.
In both Voice Alert and Tone Alert modes, a distinctly different alert tone is used
for each type of signal detected (including separate tones for each laser signal).
For X, K, Ka and Ku band radar signals, the tones will repeat faster as
you approach the signal source. The repeat rate of the tones gives you useful
information about the signal detected. (See responding to alerts on page 18.)
An indication of the type of signal detected will appear in the UltraBright
data Display. During X, K, Ka and Ku alerts, a number will also appear,
indicating the strength of the signal detected. (1 = weakest, 5 = strongest)
X Signal Detected
X K Ka V S2
K Signal DetectedKa Signal Detected
X K Ka V S3X K Ka V S5X K Ka V S4
Ku Signal Detected
14
English
Nothing Comes Close to a Cobra
®
15
Your Detector
Detection
Your Detector
Detection
During pop alerts, the letter P
will
POP Signal Detected
Laser Signal Detected
appear; and during laser alerts,
the letter L will appear, instead of
X K Ka V S P
X K Ka V S L
the signal strength indication.
During VG-2 or Spectre I or IV+
alerts, the letter V will appear.
It will be steady during VG-2
and blink during Spectre I or IV+.
During Safety Alert, the letter
VG-2 Alert Signal
Detected
X K KaV S
Safety Alert Signal Detected
c
Spectre I or IV+ Alert
Signal Detected
X K KaV S
S will appear.
X K Ka V S
Radar Signals, Voice and Visual Displays
Type of Signal Voice Visual Display
X Band Radar X AlertX and Signal Strength
K Band Radar K AlertK and Signal Strength
Ka Band Radar Ka AlertKa and Signal Strength
Ku Band Radar Ku AlertX K and Signal Strength
Pop Radar Mode Pop AlertP is Steady
X Signal Detected
X K Ka V S2
POP Alert Signal Detected
X K Ka V SP
English
16
K Signal DetectedKa Signal Detected
X K Ka V S3X K Ka V S5X K Ka V S4
c
Ku Signal Detected
Laser Signals, Voice and Visual Displays
Type of SignalVoiceVisual Display
LTI 20-20*LaserL is Steady
LTI Laser*LaserL is Steady
Kustom Signals Laser 340*LaserL is Steady
Kustom Signals Laser*LaserL is Steady
Stalker LIDAR*LaserL is Steady
c
Laser Atlanta SpeedLaser/Kustom Signals-ProLaser II*LaserL is Steady
* Your detector provides 360° detection of these signals.
Laser Signal Detected
X K Ka V SL
NOTE
Beep rate changes with different laser alerts.
Safety Alert Signals, Voice and Visual Displays
Type of Signal Voice Visual Display
Emergency Vehicles Emergency Vehicle ApproachingS is Steady
Road Hazards Road Hazard AheadS is Steady
Trains Train ApproachingS is Steady
Safety Alert Signal Detected
NOTE
X K Ka V S
c
There are different tones for each Safety Alert.
VG-2 and Spectre I or IV+ Alert Signals, Voice and Visual Displays
Type of Signal Voice Visual Display
Interceptor VG-2 VG-2 AlertV is Steady
Spectre I or IV+ Spectre AlertV Blinks
VG-2 Alert Signal Detected
Spectre I or IV+ Alert
Signal Detected
NOTE
There are different
X K KaV S
c
X K KaVS
c
tones for each alert.
Nothing Comes Close to a Cobra
®
17
Your Detector
Detection
Your Detector
Understanding Radar and Laser
Instant-On Detection
Your detector is designed to detect Instant-On speed monitoring signals, which
can suddenly appear at full strength.
NOTE
You should take appropriate action immediately
whenever an instant-on alert is given.
DescriptionInterpretation
Tone repeats slowly at first,
then speeds up rapidly.
Tone sounds one
time only.
Tone instantly begins
repeating rapidly.
Tone repeats slowly as you
approach a hill or bridge,
then speeds up sharply as
you reach it.
Tone repeats slowly
for a short period.
Any type of laser alert. Laser alerts are
Any Safety Alert.
English
18
Probably police radar.FULL ALERT
Probably a false alarm,
but possibly pulsed radar,
VG-2, or Spectre I or IV+
nearby.
Radar, VG-2 or Spectre I
or IV+ nearby has been
activated suddenly.
Probably police
radar beyond the
hill or bridge.
Probably a false alarm.Exercise caution
never false alarms.
You are nearing an
emergency vehicle, railroad
crossing, or road hazard
(construction, accident, etc.).
Recommended
Response
Exercise caution
FULL ALERT
FULL ALERT
FULL ALERT
Exercise caution
Understanding Radar and Laser
•
Radar Speed Monitoring Systems
Three band frequencies have been approved by the Federal Communications
Commission (FCC) for use by speed monitoring radar equipment:
X band10.525 GHz
K band24.150 GHz
Ka band33.400 – 36.00 GHz
Your detector detects signals in all three radar bands, plus Ku band (13.435 GHz),
which is an approved frequency used in parts of Europe and Asia.
VG-2 and Spectre I & IV+
VG-2 and Spectre I & IV+ are radar detector detectors (RDDs) that work by
detecting low-level signals emitted by most radar detectors. Your detector
does not emit signals that can be spotted by VG-2 and Spectre I RDDs.
However, your detector can be spotted by Spectre IV+ RDDs. Your unit detects
signals from these or similar devices and will alert you when such
a device is in use near your vehicle.
Safety Alert Traffic Warning System
FCC-approved Safety Alert transmitters emit microwave radar signals that
indicate the presence of a safety-related concern. Depending on the frequency
of the signal emitted, it can indicate a speeding emergency vehicle or train,
or a stationary road hazard.
Because these microwave signals are within the K band frequency, most
conventional radar detectors will detect Safety Alert signals as standard
K band radar. Your detector, however, is designed to differentiate between
standard K band and Safety Alert signals, and give separate alerts for each.
Safety Alert technology is relatively new. Safety Alert transmitters can
be found in limited numbers in all 50 states, but the number is growing.
Depending on your location, you may not receive these alerts regularly
and may often encounter emergency vehicles, trains and road hazards
without being alerted. As the number of transmitters increases,
these alerts will become more common.
When you receive such an alert, please watch for emergency vehicles ahead
of you, on cross streets and behind you. If you see an emergency vehicle
approaching, please pull over to the right side of the road and allow it to pass.
Nothing Comes Close to a Cobra
®
19
Understanding Radar and Laser
and Maintenance
Your DetectorYour Detector
Specifications
LIDAR (Laser)
The correct name for the technology that most people refer to as
laser is actually LIDAR, which stands for Light Detection and Ranging.
LIDAR operates much like radar. Its signal spreads out like a radar signal, though
not as widely. Unlike radar, LIDAR must have a clear line of sight to its target
vehicle throughout the entire measurement interval. Obstructions such as sign
posts, utility poles, tree branches, etc., will prevent valid speed measurement.
Some common questions about LIDAR include:
g
Does weather have any affect on LIDAR?
Yes. Rain, snow, smoke, fog or airborne dust particles will reduce the
effective range of LIDAR and can, if dense enough, prevent its operation.
g
Can LIDAR operate through glass?
Yes. Newer LIDAR guns can obtain readings through most types of glass.
However, the laser pulse also can be received through glass to trigger
an alarm by your detector.
g
Can LIDAR operate while in motion?
No. Because LIDAR operates by line of sight, the person using it cannot
drive the vehicle, aim and operate the gun all at the same time.
g
Is LIDAR legal to use?
Yes. It is legal in all 50 states.
Maintenance
Maintenance of Your Radar Detector
Your detector is designed and built to give you years of trouble-free performance
without the need for service. No routine Maintenance is required.
If your unit does not appear to be operating properly, please follow these
troubleshooting steps:
g
Make sure the power cord is properly connected.
g
Make sure the socket of your vehicle’s cigarette lighter is clean and
free of corrosion.
g
Make sure the power cord’s cigarette lighter adapter is firmly seated
in your cigarette lighter.
g
Connect a USB device to the type A USB port on your power cord. If it does not
provide a charge/power to your phone/device then the internal fuse is likely
blown. Contact Cobra for support or spare parts.
Cobra Electronics Corporation warrants that this product and the component parts
thereof, will be free of defects in workmanship and materials for a period of one year
from the date of rst consumer purchase. This warranty may be enforced by the rst
consumer purchaser. If the product is under warranty, it will be repaired or exchanged
depending on the model as determined at Cobra’s sole discretion. Such remedy shall
be your sole and exclusive remedy for any breach of warranty.
The procedure for obtaining service and support, and the applicability of this warranty,
will vary depending on the country or jurisdiction in which you purchased and utilize
the product. For the details on obtaining product service, support and warranty please
visit www.cobra.com/support
Provided that the product is utilized within the U.S.A.- Cobra will, without charge,
repair or replace, at its option, defective products, products or component parts upon
delivery to the Cobra Factory Service department, accompanied by proof of the date of
rst consumer purchase, such as a duplicated copy of a sales receipt. You must pay
any initial shipping charges required to ship the product for warranty service, but the
return charges, to an address in the U.S.A., will be at Cobra’s expense, if the product is
repaired or replaced under warranty.
This warranty gives you specic legal rights, and you may also have other rights which
may vary from state to state and country to country.
Exclusions: This limited warranty does not apply: 1) To any product damaged by
accident; 2) In the event of misuse, ordinary wear, failure tofollow directions, or
improper maintenance of the product or as a result of unauthorized alterations or
repairs; 3) If the serial number has been altered, defaced, or removed; 4) If the product
was purchased or is utilized in a jurisdiction not covered by the limited warranty.
All implied warranties, including warranties of merchantability and tness for a
particular purpose are limited in duration to the length of this warranty. Cobra shall
not be liable for any incidental, consequential or other damages; including, without
limitation, damages resulting from loss of use or cost of installation.
Some states and countries do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you. This warranty gives you
specic legal rights, and you may also have other rights which vary from state to state
and country to country.
Product Service and Support
•
For any questions about operating or installing this new Cobra product, PLEASE CONTACT
COBRA FIRST…do not return this product to the retail store. The contact information for
Cobra will vary depending on the country in which you purchased and utilize the product.
For the latest contact information, please go to www.cobra.com/support
For products purchased in the U.S.A. you may also call 1-773-889-3087.
For Products Purchased in the U.S.A., if your product should require factory service, please
go to www.cobra.com/support and follow the instructions for returning your product to
the Cobra Factory Service Department for service.
22
English
Nothing Comes Close to a Cobra
®
23
Customer Assistance
Optional Accessories
Optional Accessories
You can find quality Cobra products and accessories
at your local Cobra dealer, or in the U.S.A., you can
order directly from Cobra at www.cobra.com
Windshield
Mounting Bracket
Includes suction cups
Item #545-159-N-001
Dual Port Power Adapter
Includes adjustable plug
(up to 90˚) and fuse
Item # CLP-2B
Straight 12V DC
Power Cord
Includes plug and fuse
Item #420-030-N-001
Hardwire Cord for Radar
Includes fuse
Item # RA-PSCB
Coiled 12V DC
Power Cord
Includes plug and fuse
Item # 420-026-N-001
Install Mount
Includes 3M Dual Lock
Item # 545-002
Straight Combination Radar
USB Cord
Includes plug and USB
Output
Item # PWR USB-01
•
24
English
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.