Page 1
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
PETROL
MAKE
DAEWOO
MOD.
NUBIRA
YEAR
98 →→
DIESEL
ALARM/SIREN
POSITION
POWER SUPPLY + 30: connect to the 2,5mm2 RED wire located at the rear of the left lateral frame,
DIRECTION INDICATORS
ELECTRIC WINDOWS Positive control signal
Position the compact alarms and the sirens in the engine compartment near the
left lateral headlamp. Position the modular systems and the modules under the
dashboard, drivers side.
drivers side.
- 31: connect with an eyelet cable terminal to one of the fastening bolt of the
dashboard.
Connect to the 1 mm2 BLUE and LIGHT BLUE wires located in the wiring
harness and coming out of the 22 way yellow connector located on the support of
the connector holder, above the fuse box behind the left lateral frame, drivers
side.
Front window, driver’s side:
cut the BLUE wire directly outgoing from the switch of the window to the inner
drivers side door.
Front window, passenger’s side:
cut the 1,5 mm2 LIGHT BLUE wire.
Rear window, driver’s side:
cut the 1,5 mm2 BROWN wire.
Rear window, passenger’s side:
cut the 1,5 mm2 GREEN wire located in the wiring harness coming out of the
drivers side door.
CENTRAL DOORS LOCKING Negative control signal
Connect to the LIGHT BLUE wires with WHITE reference located at the position
nr. 7 (lock) and the YELLOW at the position nr. 1 (unlock), in the 9 way white
connector of the central door locking unit located at the rear of the left lateral
frame, drivers side.
Note: for the vehicles without original key less entry, please refer to
diagram nr. 42 for the serie Bridge antithefts or refer to diagram nr.42A for
serie 3100 antithefts.
IMMOBILISATION POINT
BONNET SWITCH
DOORS SWITCH
BOOT SWITCH
The vehicle has an original equipment immobiliser that may be enabled
immediately when the switchboard is switched off.
Install an additional switch on the front headlamp support plate.
Connect to the 0,5 mm2 WHITE wire located in the wiring harness coming out of
the 16 way white connector, on the support of the connector holder, above the
fuse box behind the left lateral frame, drivers side.
Connect to the 0,5 mm2 PINK wire with BLACK reference located in the wiring
harness and coming out of the 16 way white connector located on the support
mentioned above.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
danub98gbb.doc
Page 2
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
1
2
3
5
6
7
8
9
www.cobra.it
FITTING DIAGRAM N°42
Serie BRIDGE antitheft
ORANGE/VIOLET
White connector coming out of the central
doors locking unit.
VIOLET ORANGE
Negative control signal
For the versions without original radio control the positions Nr. 1 and Nr. 7 of the
white connector of the central doors closing are free, so insert suitable fastons.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
danub98gbb.doc
Page 3
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
1
2
3
5
6
7
8
9
VIOLET/WHITE
www.cobra.it
FITTING DIAGRAM N°42A
Serie 3100 antitheft
ORANGE/WHITE
White connector coming out of the central
doors locking unit.
VIOLET ORANGE
Negative control signal
For the versions without original radio control the positions Nr. 1 and Nr. 7 of the
white connector of the central doors locking are free, so insert suitable fastons.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
danub98gbb.doc
Loading...